Ricardo Benitez
meh
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_F401RE/stm32f4xx_hal_uart.h
- Revision:
- 99:dbbf35b96557
- Parent:
- 90:cb3d968589d8
- Child:
- 106:ba1f97679dad
--- a/TARGET_NUCLEO_F401RE/stm32f4xx_hal_uart.h Wed Apr 29 10:16:23 2015 +0100
+++ b/TARGET_NUCLEO_F401RE/stm32f4xx_hal_uart.h Wed May 13 08:08:21 2015 +0200
@@ -2,13 +2,13 @@
******************************************************************************
* @file stm32f4xx_hal_uart.h
* @author MCD Application Team
- * @version V1.1.0
- * @date 19-June-2014
+ * @version V1.3.0
+ * @date 09-March-2015
* @brief Header file of UART HAL module.
******************************************************************************
* @attention
*
- * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
@@ -55,6 +55,9 @@
*/
/* Exported types ------------------------------------------------------------*/
+/** @defgroup UART_Exported_Types UART Exported Types
+ * @{
+ */
/**
* @brief UART Init Structure definition
@@ -80,14 +83,14 @@
the word length is set to 9 data bits; 8th bit when the
word length is set to 8 data bits). */
- uint32_t Mode; /*!< Specifies wether the Receive or Transmit mode is enabled or disabled.
+ uint32_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
This parameter can be a value of @ref UART_Mode */
- uint32_t HwFlowCtl; /*!< Specifies wether the hardware flow control mode is enabled
+ uint32_t HwFlowCtl; /*!< Specifies whether the hardware flow control mode is enabled
or disabled.
This parameter can be a value of @ref UART_Hardware_Flow_Control */
- uint32_t OverSampling; /*!< Specifies wether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to fPCLK/8).
+ uint32_t OverSampling; /*!< Specifies whether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to fPCLK/8).
This parameter can be a value of @ref UART_Over_Sampling */
}UART_InitTypeDef;
@@ -107,202 +110,185 @@
}HAL_UART_StateTypeDef;
/**
- * @brief HAL UART Error Code structure definition
- */
-typedef enum
-{
- HAL_UART_ERROR_NONE = 0x00, /*!< No error */
- HAL_UART_ERROR_PE = 0x01, /*!< Parity error */
- HAL_UART_ERROR_NE = 0x02, /*!< Noise error */
- HAL_UART_ERROR_FE = 0x04, /*!< frame error */
- HAL_UART_ERROR_ORE = 0x08, /*!< Overrun error */
- HAL_UART_ERROR_DMA = 0x10 /*!< DMA transfer error */
-}HAL_UART_ErrorTypeDef;
-
-/**
* @brief UART handle Structure definition
*/
typedef struct
{
- USART_TypeDef *Instance; /* UART registers base address */
+ USART_TypeDef *Instance; /*!< UART registers base address */
- UART_InitTypeDef Init; /* UART communication parameters */
+ UART_InitTypeDef Init; /*!< UART communication parameters */
- uint8_t *pTxBuffPtr; /* Pointer to UART Tx transfer Buffer */
+ uint8_t *pTxBuffPtr; /*!< Pointer to UART Tx transfer Buffer */
- uint16_t TxXferSize; /* UART Tx Transfer size */
+ uint16_t TxXferSize; /*!< UART Tx Transfer size */
- uint16_t TxXferCount; /* UART Tx Transfer Counter */
+ uint16_t TxXferCount; /*!< UART Tx Transfer Counter */
- uint8_t *pRxBuffPtr; /* Pointer to UART Rx transfer Buffer */
+ uint8_t *pRxBuffPtr; /*!< Pointer to UART Rx transfer Buffer */
- uint16_t RxXferSize; /* UART Rx Transfer size */
+ uint16_t RxXferSize; /*!< UART Rx Transfer size */
- uint16_t RxXferCount; /* UART Rx Transfer Counter */
+ uint16_t RxXferCount; /*!< UART Rx Transfer Counter */
- DMA_HandleTypeDef *hdmatx; /* UART Tx DMA Handle parameters */
+ DMA_HandleTypeDef *hdmatx; /*!< UART Tx DMA Handle parameters */
- DMA_HandleTypeDef *hdmarx; /* UART Rx DMA Handle parameters */
+ DMA_HandleTypeDef *hdmarx; /*!< UART Rx DMA Handle parameters */
- HAL_LockTypeDef Lock; /* Locking object */
+ HAL_LockTypeDef Lock; /*!< Locking object */
- __IO HAL_UART_StateTypeDef State; /* UART communication state */
+ __IO HAL_UART_StateTypeDef State; /*!< UART communication state */
- __IO HAL_UART_ErrorTypeDef ErrorCode; /* UART Error code */
-
+ __IO uint32_t ErrorCode; /*!< UART Error code */
+
}UART_HandleTypeDef;
+/**
+ * @}
+ */
/* Exported constants --------------------------------------------------------*/
-/** @defgroup UART_Exported_Constants
+/** @defgroup UART_Exported_Constants UART Exported constants
* @{
*/
-
-/** @defgroup UART_Word_Length
+
+/** @defgroup UART_Error_Code UART Error Code
+ * @brief UART Error Code
+ * @{
+ */
+#define HAL_UART_ERROR_NONE ((uint32_t)0x00000000) /*!< No error */
+#define HAL_UART_ERROR_PE ((uint32_t)0x00000001) /*!< Parity error */
+#define HAL_UART_ERROR_NE ((uint32_t)0x00000002) /*!< Noise error */
+#define HAL_UART_ERROR_FE ((uint32_t)0x00000004) /*!< Frame error */
+#define HAL_UART_ERROR_ORE ((uint32_t)0x00000008) /*!< Overrun error */
+#define HAL_UART_ERROR_DMA ((uint32_t)0x00000010) /*!< DMA transfer error */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Word_Length UART Word Length
* @{
*/
#define UART_WORDLENGTH_8B ((uint32_t)0x00000000)
#define UART_WORDLENGTH_9B ((uint32_t)USART_CR1_M)
-#define IS_UART_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B) || \
- ((LENGTH) == UART_WORDLENGTH_9B))
/**
* @}
*/
-/** @defgroup UART_Stop_Bits
+/** @defgroup UART_Stop_Bits UART Number of Stop Bits
* @{
*/
#define UART_STOPBITS_1 ((uint32_t)0x00000000)
#define UART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1)
-#define IS_UART_STOPBITS(STOPBITS) (((STOPBITS) == UART_STOPBITS_1) || \
- ((STOPBITS) == UART_STOPBITS_2))
/**
* @}
*/
-/** @defgroup UART_Parity
+/** @defgroup UART_Parity UART Parity
* @{
*/
#define UART_PARITY_NONE ((uint32_t)0x00000000)
#define UART_PARITY_EVEN ((uint32_t)USART_CR1_PCE)
#define UART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
-#define IS_UART_PARITY(PARITY) (((PARITY) == UART_PARITY_NONE) || \
- ((PARITY) == UART_PARITY_EVEN) || \
- ((PARITY) == UART_PARITY_ODD))
/**
* @}
*/
-/** @defgroup UART_Hardware_Flow_Control
+/** @defgroup UART_Hardware_Flow_Control UART Hardware Flow Control
* @{
*/
#define UART_HWCONTROL_NONE ((uint32_t)0x00000000)
#define UART_HWCONTROL_RTS ((uint32_t)USART_CR3_RTSE)
#define UART_HWCONTROL_CTS ((uint32_t)USART_CR3_CTSE)
#define UART_HWCONTROL_RTS_CTS ((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE))
-#define IS_UART_HARDWARE_FLOW_CONTROL(CONTROL)\
- (((CONTROL) == UART_HWCONTROL_NONE) || \
- ((CONTROL) == UART_HWCONTROL_RTS) || \
- ((CONTROL) == UART_HWCONTROL_CTS) || \
- ((CONTROL) == UART_HWCONTROL_RTS_CTS))
/**
* @}
*/
-/** @defgroup UART_Mode
+/** @defgroup UART_Mode UART Transfer Mode
* @{
*/
#define UART_MODE_RX ((uint32_t)USART_CR1_RE)
#define UART_MODE_TX ((uint32_t)USART_CR1_TE)
#define UART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE))
-#define IS_UART_MODE(MODE) ((((MODE) & (uint32_t)0x0000FFF3) == 0x00) && ((MODE) != (uint32_t)0x000000))
/**
* @}
*/
- /** @defgroup UART_State
+ /** @defgroup UART_State UART State
* @{
*/
#define UART_STATE_DISABLE ((uint32_t)0x00000000)
#define UART_STATE_ENABLE ((uint32_t)USART_CR1_UE)
-#define IS_UART_STATE(STATE) (((STATE) == UART_STATE_DISABLE) || \
- ((STATE) == UART_STATE_ENABLE))
/**
* @}
*/
-/** @defgroup UART_Over_Sampling
+/** @defgroup UART_Over_Sampling UART Over Sampling
* @{
*/
#define UART_OVERSAMPLING_16 ((uint32_t)0x00000000)
#define UART_OVERSAMPLING_8 ((uint32_t)USART_CR1_OVER8)
-#define IS_UART_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16) || \
- ((SAMPLING) == UART_OVERSAMPLING_8))
/**
* @}
*/
-/** @defgroup UART_LIN_Break_Detection_Length
+/** @defgroup UART_LIN_Break_Detection_Length UART LIN Break Detection Length
* @{
*/
#define UART_LINBREAKDETECTLENGTH_10B ((uint32_t)0x00000000)
#define UART_LINBREAKDETECTLENGTH_11B ((uint32_t)0x00000020)
-#define IS_UART_LIN_BREAK_DETECT_LENGTH(LENGTH) (((LENGTH) == UART_LINBREAKDETECTLENGTH_10B) || \
- ((LENGTH) == UART_LINBREAKDETECTLENGTH_11B))
/**
* @}
*/
-/** @defgroup UART_WakeUp_functions
+/** @defgroup UART_WakeUp_functions UART Wakeup Functions
* @{
*/
-#define UART_WAKEUPMETHODE_IDLELINE ((uint32_t)0x00000000)
-#define UART_WAKEUPMETHODE_ADDRESSMARK ((uint32_t)0x00000800)
-#define IS_UART_WAKEUPMETHODE(WAKEUP) (((WAKEUP) == UART_WAKEUPMETHODE_IDLELINE) || \
- ((WAKEUP) == UART_WAKEUPMETHODE_ADDRESSMARK))
+#define UART_WAKEUPMETHOD_IDLELINE ((uint32_t)0x00000000)
+#define UART_WAKEUPMETHOD_ADDRESSMARK ((uint32_t)0x00000800)
/**
* @}
*/
-/** @defgroup UART_Flags
+/** @defgroup UART_Flags UART FLags
* Elements values convention: 0xXXXX
* - 0xXXXX : Flag mask in the SR register
* @{
*/
-#define UART_FLAG_CTS ((uint32_t)0x00000200)
-#define UART_FLAG_LBD ((uint32_t)0x00000100)
-#define UART_FLAG_TXE ((uint32_t)0x00000080)
-#define UART_FLAG_TC ((uint32_t)0x00000040)
-#define UART_FLAG_RXNE ((uint32_t)0x00000020)
-#define UART_FLAG_IDLE ((uint32_t)0x00000010)
-#define UART_FLAG_ORE ((uint32_t)0x00000008)
-#define UART_FLAG_NE ((uint32_t)0x00000004)
-#define UART_FLAG_FE ((uint32_t)0x00000002)
-#define UART_FLAG_PE ((uint32_t)0x00000001)
+#define UART_FLAG_CTS ((uint32_t)USART_SR_CTS)
+#define UART_FLAG_LBD ((uint32_t)USART_SR_LBD)
+#define UART_FLAG_TXE ((uint32_t)USART_SR_TXE)
+#define UART_FLAG_TC ((uint32_t)USART_SR_TC)
+#define UART_FLAG_RXNE ((uint32_t)USART_SR_RXNE)
+#define UART_FLAG_IDLE ((uint32_t)USART_SR_IDLE)
+#define UART_FLAG_ORE ((uint32_t)USART_SR_ORE)
+#define UART_FLAG_NE ((uint32_t)USART_SR_NE)
+#define UART_FLAG_FE ((uint32_t)USART_SR_FE)
+#define UART_FLAG_PE ((uint32_t)USART_SR_PE)
/**
* @}
*/
-/** @defgroup UART_Interrupt_definition
+/** @defgroup UART_Interrupt_definition UART Interrupt Definitions
* Elements values convention: 0xY000XXXX
- * - XXXX : Interrupt mask in the XX register
+ * - XXXX : Interrupt mask (16 bits) in the Y register
* - Y : Interrupt source register (2bits)
- * - 01: CR1 register
- * - 10: CR2 register
- * - 11: CR3 register
+ * - 0001: CR1 register
+ * - 0010: CR2 register
+ * - 0011: CR3 register
*
* @{
- */
-#define UART_IT_PE ((uint32_t)0x10000100)
-#define UART_IT_TXE ((uint32_t)0x10000080)
-#define UART_IT_TC ((uint32_t)0x10000040)
-#define UART_IT_RXNE ((uint32_t)0x10000020)
-#define UART_IT_IDLE ((uint32_t)0x10000010)
+ */
-#define UART_IT_LBD ((uint32_t)0x20000040)
-#define UART_IT_CTS ((uint32_t)0x30000400)
+#define UART_IT_PE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_PEIE))
+#define UART_IT_TXE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_TXEIE))
+#define UART_IT_TC ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_TCIE))
+#define UART_IT_RXNE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_RXNEIE))
+#define UART_IT_IDLE ((uint32_t)(UART_CR1_REG_INDEX << 28 | USART_CR1_IDLEIE))
-#define UART_IT_ERR ((uint32_t)0x30000001)
+#define UART_IT_LBD ((uint32_t)(UART_CR2_REG_INDEX << 28 | USART_CR2_LBDIE))
+#define UART_IT_CTS ((uint32_t)(UART_CR3_REG_INDEX << 28 | USART_CR3_CTSIE))
+#define UART_IT_ERR ((uint32_t)(UART_CR3_REG_INDEX << 28 | USART_CR3_EIE))
/**
* @}
*/
@@ -312,6 +298,9 @@
*/
/* Exported macro ------------------------------------------------------------*/
+/** @defgroup UART_Exported_Macros UART Exported Macros
+ * @{
+ */
/** @brief Reset UART handle state
* @param __HANDLE__: specifies the UART Handle.
@@ -321,7 +310,7 @@
*/
#define __HAL_UART_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_UART_STATE_RESET)
-/** @brief Flushs the UART DR register
+/** @brief Flushes the UART DR register
* @param __HANDLE__: specifies the UART Handle.
*/
#define __HAL_UART_FLUSH_DRREGISTER(__HANDLE__) ((__HANDLE__)->Instance->DR)
@@ -338,7 +327,7 @@
* @arg UART_FLAG_TC: Transmission Complete flag
* @arg UART_FLAG_RXNE: Receive data register not empty flag
* @arg UART_FLAG_IDLE: Idle Line detection flag
- * @arg UART_FLAG_ORE: OverRun Error flag
+ * @arg UART_FLAG_ORE: Overrun Error flag
* @arg UART_FLAG_NE: Noise Error flag
* @arg UART_FLAG_FE: Framing Error flag
* @arg UART_FLAG_PE: Parity Error flag
@@ -358,7 +347,7 @@
* @arg UART_FLAG_TC: Transmission Complete flag.
* @arg UART_FLAG_RXNE: Receive data register not empty flag.
*
- * @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun
+ * @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (Overrun
* error) and IDLE (Idle line detected) flags are cleared by software
* sequence: a read operation to USART_SR register followed by a read
* operation to USART_DR register.
@@ -377,8 +366,14 @@
* UART peripheral.
* @retval None
*/
-#define __HAL_UART_CLEAR_PEFLAG(__HANDLE__) do{(__HANDLE__)->Instance->SR;\
- (__HANDLE__)->Instance->DR;}while(0)
+#define __HAL_UART_CLEAR_PEFLAG(__HANDLE__) \
+ do{ \
+ __IO uint32_t tmpreg; \
+ tmpreg = (__HANDLE__)->Instance->SR; \
+ tmpreg = (__HANDLE__)->Instance->DR; \
+ UNUSED(tmpreg); \
+ } while(0)
+
/** @brief Clear the UART FE pending flag.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
@@ -411,11 +406,11 @@
*/
#define __HAL_UART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__)
-/** @brief Enables or disables the specified UART interrupt.
+/** @brief Enable the specified UART interrupt.
* @param __HANDLE__: specifies the UART Handle.
* This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
* UART peripheral.
- * @param __INTERRUPT__: specifies the UART interrupt source to check.
+ * @param __INTERRUPT__: specifies the UART interrupt source to enable.
* This parameter can be one of the following values:
* @arg UART_IT_CTS: CTS change interrupt
* @arg UART_IT_LBD: LIN Break detection interrupt
@@ -425,14 +420,28 @@
* @arg UART_IT_IDLE: Idle line detection interrupt
* @arg UART_IT_PE: Parity Error interrupt
* @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
- * @param NewState: new state of the specified UART interrupt.
- * This parameter can be: ENABLE or DISABLE.
* @retval None
*/
#define UART_IT_MASK ((uint32_t)0x0000FFFF)
#define __HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == 1)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & UART_IT_MASK)): \
(((__INTERRUPT__) >> 28) == 2)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & UART_IT_MASK)): \
((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & UART_IT_MASK)))
+/** @brief Disable the specified UART interrupt.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
+ * UART peripheral.
+ * @param __INTERRUPT__: specifies the UART interrupt source to disable.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_CTS: CTS change interrupt
+ * @arg UART_IT_LBD: LIN Break detection interrupt
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg UART_IT_PE: Parity Error interrupt
+ * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
+ * @retval None
+ */
#define __HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == 1)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & UART_IT_MASK)): \
(((__INTERRUPT__) >> 28) == 2)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & UART_IT_MASK)): \
((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & UART_IT_MASK)))
@@ -531,39 +540,56 @@
(__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_RTSE); \
} while(0)
-/** @brief macros to enables or disables the UART's one bit sampling method
+/** @brief macros to enables the UART's one bit sample method
* @param __HANDLE__: specifies the UART Handle.
* @retval None
*/
-#define __HAL_UART_ONEBIT_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)
-#define __HAL_UART_ONEBIT_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT))
+#define __HAL_UART_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)
+
+/** @brief macros to disables the UART's one bit sample method
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT))
+/** @brief Enable UART
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
#define __HAL_UART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
+
+/** @brief Disable UART
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
#define __HAL_UART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
+/**
+ * @}
+ */
-#define __DIV_SAMPLING16(_PCLK_, _BAUD_) (((_PCLK_)*25)/(4*(_BAUD_)))
-#define __DIVMANT_SAMPLING16(_PCLK_, _BAUD_) (__DIV_SAMPLING16((_PCLK_), (_BAUD_))/100)
-#define __DIVFRAQ_SAMPLING16(_PCLK_, _BAUD_) (((__DIV_SAMPLING16((_PCLK_), (_BAUD_)) - (__DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100)
-#define __UART_BRR_SAMPLING16(_PCLK_, _BAUD_) ((__DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) << 4)|(__DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0x0F))
-
-#define __DIV_SAMPLING8(_PCLK_, _BAUD_) (((_PCLK_)*25)/(2*(_BAUD_)))
-#define __DIVMANT_SAMPLING8(_PCLK_, _BAUD_) (__DIV_SAMPLING8((_PCLK_), (_BAUD_))/100)
-#define __DIVFRAQ_SAMPLING8(_PCLK_, _BAUD_) (((__DIV_SAMPLING8((_PCLK_), (_BAUD_)) - (__DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100)
-#define __UART_BRR_SAMPLING8(_PCLK_, _BAUD_) ((__DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) << 4)|(__DIVFRAQ_SAMPLING8((_PCLK_), (_BAUD_)) & 0x0F))
-
-#define IS_UART_BAUDRATE(BAUDRATE) ((BAUDRATE) < 10500001)
-#define IS_UART_ADDRESS(ADDRESS) ((ADDRESS) <= 0xF)
-
/* Exported functions --------------------------------------------------------*/
+/** @addtogroup UART_Exported_Functions
+ * @{
+ */
+
+/** @addtogroup UART_Exported_Functions_Group1
+ * @{
+ */
/* Initialization/de-initialization functions **********************************/
HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength);
-HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethode);
+HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod);
HAL_StatusTypeDef HAL_UART_DeInit (UART_HandleTypeDef *huart);
void HAL_UART_MspInit(UART_HandleTypeDef *huart);
void HAL_UART_MspDeInit(UART_HandleTypeDef *huart);
+/**
+ * @}
+ */
+/** @addtogroup UART_Exported_Functions_Group2
+ * @{
+ */
/* IO operation functions *******************************************************/
HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
@@ -580,17 +606,104 @@
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart);
void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart);
void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart);
+/**
+ * @}
+ */
+/** @addtogroup UART_Exported_Functions_Group3
+ * @{
+ */
/* Peripheral Control functions ************************************************/
HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_MultiProcessor_ExitMuteMode(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart);
HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart);
+/**
+ * @}
+ */
+/** @addtogroup UART_Exported_Functions_Group4
+ * @{
+ */
/* Peripheral State functions **************************************************/
HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart);
uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart);
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup UART_Private_Constants UART Private Constants
+ * @{
+ */
+/** @brief UART interruptions flag mask
+ *
+ */
+#define UART_CR1_REG_INDEX 1
+#define UART_CR2_REG_INDEX 2
+#define UART_CR3_REG_INDEX 3
+/**
+ * @}
+ */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup UART_Private_Macros UART Private Macros
+ * @{
+ */
+#define IS_UART_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B) || \
+ ((LENGTH) == UART_WORDLENGTH_9B))
+#define IS_UART_LIN_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B))
+#define IS_UART_STOPBITS(STOPBITS) (((STOPBITS) == UART_STOPBITS_1) || \
+ ((STOPBITS) == UART_STOPBITS_2))
+#define IS_UART_PARITY(PARITY) (((PARITY) == UART_PARITY_NONE) || \
+ ((PARITY) == UART_PARITY_EVEN) || \
+ ((PARITY) == UART_PARITY_ODD))
+#define IS_UART_HARDWARE_FLOW_CONTROL(CONTROL)\
+ (((CONTROL) == UART_HWCONTROL_NONE) || \
+ ((CONTROL) == UART_HWCONTROL_RTS) || \
+ ((CONTROL) == UART_HWCONTROL_CTS) || \
+ ((CONTROL) == UART_HWCONTROL_RTS_CTS))
+#define IS_UART_MODE(MODE) ((((MODE) & (uint32_t)0x0000FFF3) == 0x00) && ((MODE) != (uint32_t)0x000000))
+#define IS_UART_STATE(STATE) (((STATE) == UART_STATE_DISABLE) || \
+ ((STATE) == UART_STATE_ENABLE))
+#define IS_UART_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16) || \
+ ((SAMPLING) == UART_OVERSAMPLING_8))
+#define IS_UART_LIN_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16))
+#define IS_UART_LIN_BREAK_DETECT_LENGTH(LENGTH) (((LENGTH) == UART_LINBREAKDETECTLENGTH_10B) || \
+ ((LENGTH) == UART_LINBREAKDETECTLENGTH_11B))
+#define IS_UART_WAKEUPMETHOD(WAKEUP) (((WAKEUP) == UART_WAKEUPMETHOD_IDLELINE) || \
+ ((WAKEUP) == UART_WAKEUPMETHOD_ADDRESSMARK))
+#define IS_UART_BAUDRATE(BAUDRATE) ((BAUDRATE) < 10500001)
+#define IS_UART_ADDRESS(ADDRESS) ((ADDRESS) <= 0xF)
+
+#define UART_DIV_SAMPLING16(_PCLK_, _BAUD_) (((_PCLK_)*25)/(4*(_BAUD_)))
+#define UART_DIVMANT_SAMPLING16(_PCLK_, _BAUD_) (UART_DIV_SAMPLING16((_PCLK_), (_BAUD_))/100)
+#define UART_DIVFRAQ_SAMPLING16(_PCLK_, _BAUD_) (((UART_DIV_SAMPLING16((_PCLK_), (_BAUD_)) - (UART_DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100)
+#define UART_BRR_SAMPLING16(_PCLK_, _BAUD_) ((UART_DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) << 4)|(UART_DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0x0F))
+
+#define UART_DIV_SAMPLING8(_PCLK_, _BAUD_) (((_PCLK_)*25)/(2*(_BAUD_)))
+#define UART_DIVMANT_SAMPLING8(_PCLK_, _BAUD_) (UART_DIV_SAMPLING8((_PCLK_), (_BAUD_))/100)
+#define UART_DIVFRAQ_SAMPLING8(_PCLK_, _BAUD_) (((UART_DIV_SAMPLING8((_PCLK_), (_BAUD_)) - (UART_DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100)
+#define UART_BRR_SAMPLING8(_PCLK_, _BAUD_) ((UART_DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) << 4)|(UART_DIVFRAQ_SAMPLING8((_PCLK_), (_BAUD_)) & 0x0F))
+
+/**
+ * @}
+ */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup UART_Private_Functions UART Private Functions
+ * @{
+ */
+
+/**
+ * @}
+ */
/**
* @}
@@ -598,8 +711,8 @@
/**
* @}
- */
-
+ */
+
#ifdef __cplusplus
}
#endif