Ricardo Benitez
meh
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_F401RE/stm32f4xx_hal_uart.h
- Revision:
- 77:869cf507173a
- Child:
- 81:7d30d6019079
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/TARGET_NUCLEO_F401RE/stm32f4xx_hal_uart.h Fri Feb 14 14:36:43 2014 +0000
@@ -0,0 +1,480 @@
+/**
+ ******************************************************************************
+ * @file stm32f4xx_hal_uart.h
+ * @author MCD Application Team
+ * @version V1.0.0RC2
+ * @date 04-February-2014
+ * @brief Header file of UART HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F4xx_HAL_UART_H
+#define __STM32F4xx_HAL_UART_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f4xx_hal_def.h"
+
+/** @addtogroup STM32F4xx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup UART
+ * @{
+ */
+
+/* Exported types ------------------------------------------------------------*/
+
+/**
+ * @brief UART Init Structure definition
+ */
+typedef struct
+{
+ uint32_t BaudRate; /*!< This member configures the UART communication baud rate.
+ The baud rate is computed using the following formula:
+ - IntegerDivider = ((PCLKx) / (8 * (OVR8+1) * (huart->Init.BaudRate)))
+ - FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 8 * (OVR8+1)) + 0.5
+ Where OVR8 is the "oversampling by 8 mode" configuration bit in the CR1 register. */
+
+ uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
+ This parameter can be a value of @ref UART_Word_Length */
+
+ uint32_t StopBits; /*!< Specifies the number of stop bits transmitted.
+ This parameter can be a value of @ref UART_Stop_Bits */
+
+ uint32_t Parity; /*!< Specifies the parity mode.
+ This parameter can be a value of @ref UART_Parity
+ @note When parity is enabled, the computed parity is inserted
+ at the MSB position of the transmitted data (9th bit when
+ the word length is set to 9 data bits; 8th bit when the
+ word length is set to 8 data bits). */
+
+ uint32_t Mode; /*!< Specifies wether the Receive or Transmit mode is enabled or disabled.
+ This parameter can be a value of @ref UART_Mode */
+
+ uint32_t HwFlowCtl; /*!< Specifies wether the hardware flow control mode is enabled
+ or disabled.
+ This parameter can be a value of @ref UART_Hardware_Flow_Control */
+
+ uint32_t OverSampling; /*!< Specifies wether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to fPCLK/8).
+ This parameter can be a value of @ref UART_Over_Sampling */
+}UART_InitTypeDef;
+
+/**
+ * @brief HAL UART State structures definition
+ */
+typedef enum
+{
+ HAL_UART_STATE_RESET = 0x00, /*!< Peripheral is not yet Initialized */
+ HAL_UART_STATE_READY = 0x01, /*!< Peripheral Initialized and ready for use */
+ HAL_UART_STATE_BUSY = 0x02, /*!< an internal process is ongoing */
+ HAL_UART_STATE_BUSY_TX = 0x12, /*!< Data Transmission process is ongoing */
+ HAL_UART_STATE_BUSY_RX = 0x22, /*!< Data Reception process is ongoing */
+ HAL_UART_STATE_BUSY_TX_RX = 0x32, /*!< Data Transmission and Reception process is ongoing */
+ HAL_UART_STATE_TIMEOUT = 0x03, /*!< Timeout state */
+ HAL_UART_STATE_ERROR = 0x04 /*!< Error */
+}HAL_UART_StateTypeDef;
+
+/**
+ * @brief HAL UART Error Code structure definition
+ */
+typedef enum
+{
+ HAL_UART_ERROR_NONE = 0x00, /*!< No error */
+ HAL_UART_ERROR_PE = 0x01, /*!< Parity error */
+ HAL_UART_ERROR_NE = 0x02, /*!< Noise error */
+ HAL_UART_ERROR_FE = 0x04, /*!< frame error */
+ HAL_UART_ERROR_ORE = 0x08, /*!< Overrun error */
+ HAL_UART_ERROR_DMA = 0x10 /*!< DMA transfer error */
+}HAL_UART_ErrorTypeDef;
+
+/**
+ * @brief UART handle Structure definition
+ */
+typedef struct
+{
+ USART_TypeDef *Instance; /* UART registers base address */
+
+ UART_InitTypeDef Init; /* UART communication parameters */
+
+ uint8_t *pTxBuffPtr; /* Pointer to UART Tx transfer Buffer */
+
+ uint16_t TxXferSize; /* UART Tx Transfer size */
+
+ uint16_t TxXferCount; /* UART Tx Transfer Counter */
+
+ uint8_t *pRxBuffPtr; /* Pointer to UART Rx transfer Buffer */
+
+ uint16_t RxXferSize; /* UART Rx Transfer size */
+
+ uint16_t RxXferCount; /* UART Rx Transfer Counter */
+
+ DMA_HandleTypeDef *hdmatx; /* UART Tx DMA Handle parameters */
+
+ DMA_HandleTypeDef *hdmarx; /* UART Rx DMA Handle parameters */
+
+ HAL_LockTypeDef Lock; /* Locking object */
+
+ __IO HAL_UART_StateTypeDef State; /* UART communication state */
+
+ __IO HAL_UART_ErrorTypeDef ErrorCode; /* UART Error code */
+
+}UART_HandleTypeDef;
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup UART_Exported_Constants
+ * @{
+ */
+
+/** @defgroup UART_Word_Length
+ * @{
+ */
+#define UART_WORDLENGTH_8B ((uint32_t)0x00000000)
+#define UART_WORDLENGTH_9B ((uint32_t)USART_CR1_M)
+#define IS_UART_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B) || \
+ ((LENGTH) == UART_WORDLENGTH_9B))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Stop_Bits
+ * @{
+ */
+#define UART_STOPBITS_1 ((uint32_t)0x00000000)
+#define UART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1)
+#define IS_UART_STOPBITS(STOPBITS) (((STOPBITS) == UART_STOPBITS_1) || \
+ ((STOPBITS) == UART_STOPBITS_2))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Parity
+ * @{
+ */
+#define UART_PARITY_NONE ((uint32_t)0x00000000)
+#define UART_PARITY_EVEN ((uint32_t)USART_CR1_PCE)
+#define UART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
+#define IS_UART_PARITY(PARITY) (((PARITY) == UART_PARITY_NONE) || \
+ ((PARITY) == UART_PARITY_EVEN) || \
+ ((PARITY) == UART_PARITY_ODD))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Hardware_Flow_Control
+ * @{
+ */
+#define UART_HWCONTROL_NONE ((uint32_t)0x00000000)
+#define UART_HWCONTROL_RTS ((uint32_t)USART_CR3_RTSE)
+#define UART_HWCONTROL_CTS ((uint32_t)USART_CR3_CTSE)
+#define UART_HWCONTROL_RTS_CTS ((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE))
+#define IS_UART_HARDWARE_FLOW_CONTROL(CONTROL)\
+ (((CONTROL) == UART_HWCONTROL_NONE) || \
+ ((CONTROL) == UART_HWCONTROL_RTS) || \
+ ((CONTROL) == UART_HWCONTROL_CTS) || \
+ ((CONTROL) == UART_HWCONTROL_RTS_CTS))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Mode
+ * @{
+ */
+#define UART_MODE_RX ((uint32_t)USART_CR1_RE)
+#define UART_MODE_TX ((uint32_t)USART_CR1_TE)
+#define UART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE))
+#define IS_UART_MODE(MODE) ((((MODE) & (uint32_t)0x0000FFF3) == 0x00) && ((MODE) != (uint32_t)0x000000))
+/**
+ * @}
+ */
+
+ /** @defgroup UART_State
+ * @{
+ */
+#define UART_STATE_DISABLE ((uint32_t)0x00000000)
+#define UART_STATE_ENABLE ((uint32_t)USART_CR1_UE)
+#define IS_UART_STATE(STATE) (((STATE) == UART_STATE_DISABLE) || \
+ ((STATE) == UART_STATE_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Over_Sampling
+ * @{
+ */
+#define UART_OVERSAMPLING_16 ((uint32_t)0x00000000)
+#define UART_OVERSAMPLING_8 ((uint32_t)USART_CR1_OVER8)
+#define IS_UART_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16) || \
+ ((SAMPLING) == UART_OVERSAMPLING_8))
+/**
+ * @}
+ */
+
+/** @defgroup UART_LIN_Break_Detection_Length
+ * @{
+ */
+#define UART_LINBREAKDETECTLENGTH_10B ((uint32_t)0x00000000)
+#define UART_LINBREAKDETECTLENGTH_11B ((uint32_t)0x00000020)
+#define IS_UART_LIN_BREAK_DETECT_LENGTH(LENGTH) (((LENGTH) == UART_LINBREAKDETECTLENGTH_10B) || \
+ ((LENGTH) == UART_LINBREAKDETECTLENGTH_11B))
+/**
+ * @}
+ */
+
+/** @defgroup UART_WakeUp_functions
+ * @{
+ */
+#define UART_WAKEUPMETHODE_IDLELINE ((uint32_t)0x00000000)
+#define UART_WAKEUPMETHODE_ADDRESSMARK ((uint32_t)0x00000800)
+#define IS_UART_WAKEUPMETHODE(WAKEUP) (((WAKEUP) == UART_WAKEUPMETHODE_IDLELINE) || \
+ ((WAKEUP) == UART_WAKEUPMETHODE_ADDRESSMARK))
+/**
+ * @}
+ */
+
+/** @defgroup UART_Flags
+ * Elements values convention: 0xXXXX
+ * - 0xXXXX : Flag mask in the SR register
+ * @{
+ */
+#define UART_FLAG_CTS ((uint32_t)0x00000200)
+#define UART_FLAG_LBD ((uint32_t)0x00000100)
+#define UART_FLAG_TXE ((uint32_t)0x00000080)
+#define UART_FLAG_TC ((uint32_t)0x00000040)
+#define UART_FLAG_RXNE ((uint32_t)0x00000020)
+#define UART_FLAG_IDLE ((uint32_t)0x00000010)
+#define UART_FLAG_ORE ((uint32_t)0x00000008)
+#define UART_FLAG_NE ((uint32_t)0x00000004)
+#define UART_FLAG_FE ((uint32_t)0x00000002)
+#define UART_FLAG_PE ((uint32_t)0x00000001)
+/**
+ * @}
+ */
+
+/** @defgroup UART_Interrupt_definition
+ * Elements values convention: 0xY000XXXX
+ * - XXXX : Interrupt mask in the XX register
+ * - Y : Interrupt source register (2bits)
+ * - 01: CR1 register
+ * - 10: CR2 register
+ * - 11: CR3 register
+ *
+ * @{
+ */
+#define UART_IT_PE ((uint32_t)0x10000100)
+#define UART_IT_TXE ((uint32_t)0x10000080)
+#define UART_IT_TC ((uint32_t)0x10000040)
+#define UART_IT_RXNE ((uint32_t)0x10000020)
+#define UART_IT_IDLE ((uint32_t)0x10000010)
+
+#define UART_IT_LBD ((uint32_t)0x20000040)
+#define UART_IT_CTS ((uint32_t)0x30000400)
+
+#define UART_IT_ERR ((uint32_t)0x30000001)
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported macro ------------------------------------------------------------*/
+
+/** @brief Checks whether the specified UART flag is set or not.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
+ * UART peripheral.
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5)
+ * @arg UART_FLAG_LBD: LIN Break detection flag
+ * @arg UART_FLAG_TXE: Transmit data register empty flag
+ * @arg UART_FLAG_TC: Transmission Complete flag
+ * @arg UART_FLAG_RXNE: Receive data register not empty flag
+ * @arg UART_FLAG_IDLE: Idle Line detection flag
+ * @arg UART_FLAG_ORE: OverRun Error flag
+ * @arg UART_FLAG_NE: Noise Error flag
+ * @arg UART_FLAG_FE: Framing Error flag
+ * @arg UART_FLAG_PE: Parity Error flag
+ * @retval The new state of __FLAG__ (TRUE or FALSE).
+ */
+
+#define __HAL_UART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))
+
+/** @brief Clears the specified UART pending flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
+ * UART peripheral.
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be any combination of the following values:
+ * @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5).
+ * @arg UART_FLAG_LBD: LIN Break detection flag.
+ * @arg UART_FLAG_TC: Transmission Complete flag.
+ * @arg UART_FLAG_RXNE: Receive data register not empty flag.
+ *
+ * @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun
+ * error) and IDLE (Idle line detected) flags are cleared by software
+ * sequence: a read operation to USART_SR register followed by a read
+ * operation to USART_DR register.
+ * @note RXNE flag can be also cleared by a read to the USART_DR register.
+ * @note TC flag can be also cleared by software sequence: a read operation to
+ * USART_SR register followed by a write operation to USART_DR register.
+ * @note TXE flag is cleared only by a write to the USART_DR register.
+ *
+ * @retval None
+ */
+#define __HAL_UART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR &= ~(__FLAG__))
+
+/** @brief Enables or disables the specified UART interrupt.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
+ * UART peripheral.
+ * @param __INTERRUPT__: specifies the UART interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_CTS: CTS change interrupt
+ * @arg UART_IT_LBD: LIN Break detection interrupt
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg UART_IT_PE: Parity Error interrupt
+ * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
+ * @param NewState: new state of the specified UART interrupt.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+#define UART_IT_MASK ((uint32_t)0x0000FFFF)
+#define __HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == 1)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & UART_IT_MASK)): \
+ (((__INTERRUPT__) >> 28) == 2)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & UART_IT_MASK)): \
+ ((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & UART_IT_MASK)))
+#define __HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28) == 1)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & UART_IT_MASK)): \
+ (((__INTERRUPT__) >> 28) == 2)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & UART_IT_MASK)): \
+ ((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & UART_IT_MASK)))
+
+/** @brief Checks whether the specified UART interrupt has occurred or not.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or
+ * UART peripheral.
+ * @param __IT__: specifies the UART interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
+ * @arg UART_IT_LBD: LIN Break detection interrupt
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg USART_IT_ERR: Error interrupt
+ * @retval The new state of __IT__ (TRUE or FALSE).
+ */
+#define __HAL_UART_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28) == 1)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28) == 2)? \
+ (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & UART_IT_MASK))
+
+/** @brief macros to enables or disables the UART's one bit sampling method
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_ONEBIT_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)
+#define __HAL_UART_ONEBIT_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT))
+
+#define __HAL_UART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
+#define __HAL_UART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
+
+#define __DIV_SAMPLING16(_PCLK_, _BAUD_) (((_PCLK_)*25)/(4*(_BAUD_)))
+#define __DIVMANT_SAMPLING16(_PCLK_, _BAUD_) (__DIV_SAMPLING16((_PCLK_), (_BAUD_))/100)
+#define __DIVFRAQ_SAMPLING16(_PCLK_, _BAUD_) (((__DIV_SAMPLING16((_PCLK_), (_BAUD_)) - (__DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100)
+#define __UART_BRR_SAMPLING16(_PCLK_, _BAUD_) ((__DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) << 4)|(__DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0x0F))
+
+#define __DIV_SAMPLING8(_PCLK_, _BAUD_) (((_PCLK_)*25)/(2*(_BAUD_)))
+#define __DIVMANT_SAMPLING8(_PCLK_, _BAUD_) (__DIV_SAMPLING8((_PCLK_), (_BAUD_))/100)
+#define __DIVFRAQ_SAMPLING8(_PCLK_, _BAUD_) (((__DIV_SAMPLING8((_PCLK_), (_BAUD_)) - (__DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) * 100)) * 16 + 50) / 100)
+#define __UART_BRR_SAMPLING8(_PCLK_, _BAUD_) ((__DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) << 4)|(__DIVFRAQ_SAMPLING8((_PCLK_), (_BAUD_)) & 0x0F))
+
+#define IS_UART_BAUDRATE(BAUDRATE) ((BAUDRATE) < 10500001)
+#define IS_UART_ADDRESS(ADDRESS) ((ADDRESS) <= 0xF)
+
+/* Exported functions --------------------------------------------------------*/
+/* Initialization/de-initialization functions **********************************/
+HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength);
+HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethode);
+HAL_StatusTypeDef HAL_UART_DeInit (UART_HandleTypeDef *huart);
+__weak void HAL_UART_MspInit(UART_HandleTypeDef *huart);
+__weak void HAL_UART_MspDeInit(UART_HandleTypeDef *huart);
+
+/* IO operation functions *******************************************************/
+HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart);
+void HAL_UART_IRQHandler(UART_HandleTypeDef *huart);
+__weak void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart);
+__weak void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart);
+__weak void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart);
+__weak void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart);
+__weak void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart);
+
+/* Peripheral Control functions ************************************************/
+HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_MultiProcessor_ExitMuteMode(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart);
+
+/* Peripheral State functions **************************************************/
+HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart);
+uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart);
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F4xx_HAL_UART_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/