Ricardo Benitez
meh
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_F334R8/stm32f3xx_ll_fmc.h
- Revision:
- 92:4fc01daae5a5
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/TARGET_NUCLEO_F334R8/stm32f3xx_ll_fmc.h Thu Nov 27 13:33:22 2014 +0000
@@ -0,0 +1,956 @@
+/**
+ ******************************************************************************
+ * @file stm32f3xx_ll_fmc.h
+ * @author MCD Application Team
+ * @version V1.1.0
+ * @date 12-Sept-2014
+ * @brief Header file of FMC HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F3xx_LL_FMC_H
+#define __STM32F3xx_LL_FMC_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#if defined(STM32F302xE) || defined(STM32F303xE) || defined(STM32F398xx)
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f3xx_hal_def.h"
+
+/** @addtogroup STM32F3xx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup FMC
+ * @{
+ */
+
+/* Exported typedef ----------------------------------------------------------*/
+#define FMC_NORSRAM_TypeDef FMC_Bank1_TypeDef
+#define FMC_NORSRAM_EXTENDED_TypeDef FMC_Bank1E_TypeDef
+#define FMC_NAND_TypeDef FMC_Bank2_3_TypeDef
+#define FMC_PCCARD_TypeDef FMC_Bank4_TypeDef
+
+#define FMC_NORSRAM_DEVICE FMC_Bank1
+#define FMC_NORSRAM_EXTENDED_DEVICE FMC_Bank1E
+#define FMC_NAND_DEVICE FMC_Bank2_3
+#define FMC_PCCARD_DEVICE FMC_Bank4
+
+/**
+ * @brief FMC_NORSRAM Configuration Structure definition
+ */
+typedef struct
+{
+ uint32_t NSBank; /*!< Specifies the NORSRAM memory device that will be used.
+ This parameter can be a value of @ref FMC_NORSRAM_Bank */
+
+ uint32_t DataAddressMux; /*!< Specifies whether the address and data values are
+ multiplexed on the data bus or not.
+ This parameter can be a value of @ref FMC_Data_Address_Bus_Multiplexing */
+
+ uint32_t MemoryType; /*!< Specifies the type of external memory attached to
+ the corresponding memory device.
+ This parameter can be a value of @ref FMC_Memory_Type */
+
+ uint32_t MemoryDataWidth; /*!< Specifies the external memory device width.
+ This parameter can be a value of @ref FMC_NORSRAM_Data_Width */
+
+ uint32_t BurstAccessMode; /*!< Enables or disables the burst access mode for Flash memory,
+ valid only with synchronous burst Flash memories.
+ This parameter can be a value of @ref FMC_Burst_Access_Mode */
+
+ uint32_t WaitSignalPolarity; /*!< Specifies the wait signal polarity, valid only when accessing
+ the Flash memory in burst mode.
+ This parameter can be a value of @ref FMC_Wait_Signal_Polarity */
+
+ uint32_t WrapMode; /*!< Enables or disables the Wrapped burst access mode for Flash
+ memory, valid only when accessing Flash memories in burst mode.
+ This parameter can be a value of @ref FMC_Wrap_Mode */
+
+ uint32_t WaitSignalActive; /*!< Specifies if the wait signal is asserted by the memory one
+ clock cycle before the wait state or during the wait state,
+ valid only when accessing memories in burst mode.
+ This parameter can be a value of @ref FMC_Wait_Timing */
+
+ uint32_t WriteOperation; /*!< Enables or disables the write operation in the selected device by the FMC.
+ This parameter can be a value of @ref FMC_Write_Operation */
+
+ uint32_t WaitSignal; /*!< Enables or disables the wait state insertion via wait
+ signal, valid for Flash memory access in burst mode.
+ This parameter can be a value of @ref FMC_Wait_Signal */
+
+ uint32_t ExtendedMode; /*!< Enables or disables the extended mode.
+ This parameter can be a value of @ref FMC_Extended_Mode */
+
+ uint32_t AsynchronousWait; /*!< Enables or disables wait signal during asynchronous transfers,
+ valid only with asynchronous Flash memories.
+ This parameter can be a value of @ref FMC_AsynchronousWait */
+
+ uint32_t WriteBurst; /*!< Enables or disables the write burst operation.
+ This parameter can be a value of @ref FMC_Write_Burst */
+
+ uint32_t ContinuousClock; /*!< Enables or disables the FMC clock output to external memory devices.
+ This parameter is only enabled through the FMC_BCR1 register, and don't care
+ through FMC_BCR2..4 registers.
+ This parameter can be a value of @ref FMC_Continous_Clock */
+
+}FMC_NORSRAM_InitTypeDef;
+
+/**
+ * @brief FMC_NORSRAM Timing parameters structure definition
+ */
+typedef struct
+{
+ uint32_t AddressSetupTime; /*!< Defines the number of HCLK cycles to configure
+ the duration of the address setup time.
+ This parameter can be a value between Min_Data = 0 and Max_Data = 15.
+ @note This parameter is not used with synchronous NOR Flash memories. */
+
+ uint32_t AddressHoldTime; /*!< Defines the number of HCLK cycles to configure
+ the duration of the address hold time.
+ This parameter can be a value between Min_Data = 1 and Max_Data = 15.
+ @note This parameter is not used with synchronous NOR Flash memories. */
+
+ uint32_t DataSetupTime; /*!< Defines the number of HCLK cycles to configure
+ the duration of the data setup time.
+ This parameter can be a value between Min_Data = 1 and Max_Data = 255.
+ @note This parameter is used for SRAMs, ROMs and asynchronous multiplexed
+ NOR Flash memories. */
+
+ uint32_t BusTurnAroundDuration; /*!< Defines the number of HCLK cycles to configure
+ the duration of the bus turnaround.
+ This parameter can be a value between Min_Data = 0 and Max_Data = 15.
+ @note This parameter is only used for multiplexed NOR Flash memories. */
+
+ uint32_t CLKDivision; /*!< Defines the period of CLK clock output signal, expressed in number of
+ HCLK cycles. This parameter can be a value between Min_Data = 2 and Max_Data = 16.
+ @note This parameter is not used for asynchronous NOR Flash, SRAM or ROM
+ accesses. */
+
+ uint32_t DataLatency; /*!< Defines the number of memory clock cycles to issue
+ to the memory before getting the first data.
+ The parameter value depends on the memory type as shown below:
+ - It must be set to 0 in case of a CRAM
+ - It is don't care in asynchronous NOR, SRAM or ROM accesses
+ - It may assume a value between Min_Data = 2 and Max_Data = 17 in NOR Flash memories
+ with synchronous burst mode enable */
+
+ uint32_t AccessMode; /*!< Specifies the asynchronous access mode.
+ This parameter can be a value of @ref FMC_Access_Mode */
+
+}FMC_NORSRAM_TimingTypeDef;
+
+/**
+ * @brief FMC_NAND Configuration Structure definition
+ */
+typedef struct
+{
+ uint32_t NandBank; /*!< Specifies the NAND memory device that will be used.
+ This parameter can be a value of @ref FMC_NAND_Bank */
+
+ uint32_t Waitfeature; /*!< Enables or disables the Wait feature for the NAND Memory device.
+ This parameter can be any value of @ref FMC_Wait_feature */
+
+ uint32_t MemoryDataWidth; /*!< Specifies the external memory device width.
+ This parameter can be any value of @ref FMC_NAND_Data_Width */
+
+ uint32_t EccComputation; /*!< Enables or disables the ECC computation.
+ This parameter can be any value of @ref FMC_ECC */
+
+ uint32_t ECCPageSize; /*!< Defines the page size for the extended ECC.
+ This parameter can be any value of @ref FMC_ECC_Page_Size */
+
+ uint32_t TCLRSetupTime; /*!< Defines the number of HCLK cycles to configure the
+ delay between CLE low and RE low.
+ This parameter can be a value between Min_Data = 0 and Max_Data = 255 */
+
+ uint32_t TARSetupTime; /*!< Defines the number of HCLK cycles to configure the
+ delay between ALE low and RE low.
+ This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
+
+}FMC_NAND_InitTypeDef;
+
+/**
+ * @brief FMC_NAND_PCCARD Timing parameters structure definition
+ */
+typedef struct
+{
+ uint32_t SetupTime; /*!< Defines the number of HCLK cycles to setup address before
+ the command assertion for NAND-Flash read or write access
+ to common/Attribute or I/O memory space (depending on
+ the memory space timing to be configured).
+ This parameter can be a value between Min_Data = 0 and Max_Data = 255 */
+
+ uint32_t WaitSetupTime; /*!< Defines the minimum number of HCLK cycles to assert the
+ command for NAND-Flash read or write access to
+ common/Attribute or I/O memory space (depending on the
+ memory space timing to be configured).
+ This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
+
+ uint32_t HoldSetupTime; /*!< Defines the number of HCLK clock cycles to hold address
+ (and data for write access) after the command de-assertion
+ for NAND-Flash read or write access to common/Attribute
+ or I/O memory space (depending on the memory space timing
+ to be configured).
+ This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
+
+ uint32_t HiZSetupTime; /*!< Defines the number of HCLK clock cycles during which the
+ data bus is kept in HiZ after the start of a NAND-Flash
+ write access to common/Attribute or I/O memory space (depending
+ on the memory space timing to be configured).
+ This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
+
+}FMC_NAND_PCC_TimingTypeDef;
+
+/**
+ * @brief FMC_NAND Configuration Structure definition
+ */
+typedef struct
+{
+ uint32_t Waitfeature; /*!< Enables or disables the Wait feature for the PCCARD Memory device.
+ This parameter can be any value of @ref FMC_Wait_feature */
+
+ uint32_t TCLRSetupTime; /*!< Defines the number of HCLK cycles to configure the
+ delay between CLE low and RE low.
+ This parameter can be a value between Min_Data = 0 and Max_Data = 255 */
+
+ uint32_t TARSetupTime; /*!< Defines the number of HCLK cycles to configure the
+ delay between ALE low and RE low.
+ This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
+
+}FMC_PCCARD_InitTypeDef;
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup FMC_NOR_SRAM_Controller
+ * @{
+ */
+
+/** @defgroup FMC_NORSRAM_Bank
+ * @{
+ */
+#define FMC_NORSRAM_BANK1 ((uint32_t)0x00000000)
+#define FMC_NORSRAM_BANK2 ((uint32_t)0x00000002)
+#define FMC_NORSRAM_BANK3 ((uint32_t)0x00000004)
+#define FMC_NORSRAM_BANK4 ((uint32_t)0x00000006)
+
+#define IS_FMC_NORSRAM_BANK(BANK) (((BANK) == FMC_NORSRAM_BANK1) || \
+ ((BANK) == FMC_NORSRAM_BANK2) || \
+ ((BANK) == FMC_NORSRAM_BANK3) || \
+ ((BANK) == FMC_NORSRAM_BANK4))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Data_Address_Bus_Multiplexing
+ * @{
+ */
+#define FMC_DATA_ADDRESS_MUX_DISABLE ((uint32_t)0x00000000)
+#define FMC_DATA_ADDRESS_MUX_ENABLE ((uint32_t)0x00000002)
+
+#define IS_FMC_MUX(MUX) (((MUX) == FMC_DATA_ADDRESS_MUX_DISABLE) || \
+ ((MUX) == FMC_DATA_ADDRESS_MUX_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Memory_Type
+ * @{
+ */
+#define FMC_MEMORY_TYPE_SRAM ((uint32_t)0x00000000)
+#define FMC_MEMORY_TYPE_PSRAM ((uint32_t)0x00000004)
+#define FMC_MEMORY_TYPE_NOR ((uint32_t)0x00000008)
+
+#define IS_FMC_MEMORY(MEMORY) (((MEMORY) == FMC_MEMORY_TYPE_SRAM) || \
+ ((MEMORY) == FMC_MEMORY_TYPE_PSRAM)|| \
+ ((MEMORY) == FMC_MEMORY_TYPE_NOR))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_NORSRAM_Data_Width
+ * @{
+ */
+#define FMC_NORSRAM_MEM_BUS_WIDTH_8 ((uint32_t)0x00000000)
+#define FMC_NORSRAM_MEM_BUS_WIDTH_16 ((uint32_t)0x00000010)
+#define FMC_NORSRAM_MEM_BUS_WIDTH_32 ((uint32_t)0x00000020)
+
+#define IS_FMC_NORSRAM_MEMORY_WIDTH(WIDTH) (((WIDTH) == FMC_NORSRAM_MEM_BUS_WIDTH_8) || \
+ ((WIDTH) == FMC_NORSRAM_MEM_BUS_WIDTH_16) || \
+ ((WIDTH) == FMC_NORSRAM_MEM_BUS_WIDTH_32))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_NORSRAM_Flash_Access
+ * @{
+ */
+#define FMC_NORSRAM_FLASH_ACCESS_ENABLE ((uint32_t)0x00000040)
+#define FMC_NORSRAM_FLASH_ACCESS_DISABLE ((uint32_t)0x00000000)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Burst_Access_Mode
+ * @{
+ */
+#define FMC_BURST_ACCESS_MODE_DISABLE ((uint32_t)0x00000000)
+#define FMC_BURST_ACCESS_MODE_ENABLE ((uint32_t)0x00000100)
+
+#define IS_FMC_BURSTMODE(STATE) (((STATE) == FMC_BURST_ACCESS_MODE_DISABLE) || \
+ ((STATE) == FMC_BURST_ACCESS_MODE_ENABLE))
+/**
+ * @}
+ */
+
+
+/** @defgroup FMC_Wait_Signal_Polarity
+ * @{
+ */
+#define FMC_WAIT_SIGNAL_POLARITY_LOW ((uint32_t)0x00000000)
+#define FMC_WAIT_SIGNAL_POLARITY_HIGH ((uint32_t)0x00000200)
+
+#define IS_FMC_WAIT_POLARITY(POLARITY) (((POLARITY) == FMC_WAIT_SIGNAL_POLARITY_LOW) || \
+ ((POLARITY) == FMC_WAIT_SIGNAL_POLARITY_HIGH))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Wrap_Mode
+ * @{
+ */
+#define FMC_WRAP_MODE_DISABLE ((uint32_t)0x00000000)
+#define FMC_WRAP_MODE_ENABLE ((uint32_t)0x00000400)
+
+#define IS_FMC_WRAP_MODE(MODE) (((MODE) == FMC_WRAP_MODE_DISABLE) || \
+ ((MODE) == FMC_WRAP_MODE_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Wait_Timing
+ * @{
+ */
+#define FMC_WAIT_TIMING_BEFORE_WS ((uint32_t)0x00000000)
+#define FMC_WAIT_TIMING_DURING_WS ((uint32_t)0x00000800)
+
+#define IS_FMC_WAIT_SIGNAL_ACTIVE(ACTIVE) (((ACTIVE) == FMC_WAIT_TIMING_BEFORE_WS) || \
+ ((ACTIVE) == FMC_WAIT_TIMING_DURING_WS))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Write_Operation
+ * @{
+ */
+#define FMC_WRITE_OPERATION_DISABLE ((uint32_t)0x00000000)
+#define FMC_WRITE_OPERATION_ENABLE ((uint32_t)0x00001000)
+
+#define IS_FMC_WRITE_OPERATION(OPERATION) (((OPERATION) == FMC_WRITE_OPERATION_DISABLE) || \
+ ((OPERATION) == FMC_WRITE_OPERATION_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Wait_Signal
+ * @{
+ */
+#define FMC_WAIT_SIGNAL_DISABLE ((uint32_t)0x00000000)
+#define FMC_WAIT_SIGNAL_ENABLE ((uint32_t)0x00002000)
+
+#define IS_FMC_WAITE_SIGNAL(SIGNAL) (((SIGNAL) == FMC_WAIT_SIGNAL_DISABLE) || \
+ ((SIGNAL) == FMC_WAIT_SIGNAL_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Extended_Mode
+ * @{
+ */
+#define FMC_EXTENDED_MODE_DISABLE ((uint32_t)0x00000000)
+#define FMC_EXTENDED_MODE_ENABLE ((uint32_t)0x00004000)
+
+#define IS_FMC_EXTENDED_MODE(MODE) (((MODE) == FMC_EXTENDED_MODE_DISABLE) || \
+ ((MODE) == FMC_EXTENDED_MODE_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_AsynchronousWait
+ * @{
+ */
+#define FMC_ASYNCHRONOUS_WAIT_DISABLE ((uint32_t)0x00000000)
+#define FMC_ASYNCHRONOUS_WAIT_ENABLE ((uint32_t)0x00008000)
+
+#define IS_FMC_ASYNWAIT(STATE) (((STATE) == FMC_ASYNCHRONOUS_WAIT_DISABLE) || \
+ ((STATE) == FMC_ASYNCHRONOUS_WAIT_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Write_Burst
+ * @{
+ */
+#define FMC_WRITE_BURST_DISABLE ((uint32_t)0x00000000)
+#define FMC_WRITE_BURST_ENABLE ((uint32_t)0x00080000)
+
+#define IS_FMC_WRITE_BURST(BURST) (((BURST) == FMC_WRITE_BURST_DISABLE) || \
+ ((BURST) == FMC_WRITE_BURST_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Continous_Clock
+ * @{
+ */
+#define FMC_CONTINUOUS_CLOCK_SYNC_ONLY ((uint32_t)0x00000000)
+#define FMC_CONTINUOUS_CLOCK_SYNC_ASYNC ((uint32_t)0x00100000)
+
+#define IS_FMC_CONTINOUS_CLOCK(CCLOCK) (((CCLOCK) == FMC_CONTINUOUS_CLOCK_SYNC_ONLY) || \
+ ((CCLOCK) == FMC_CONTINUOUS_CLOCK_SYNC_ASYNC))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Address_Setup_Time
+ * @{
+ */
+#define IS_FMC_ADDRESS_SETUP_TIME(TIME) ((TIME) <= 15)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Address_Hold_Time
+ * @{
+ */
+#define IS_FMC_ADDRESS_HOLD_TIME(TIME) (((TIME) > 0) && ((TIME) <= 15))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Data_Setup_Time
+ * @{
+ */
+#define IS_FMC_DATASETUP_TIME(TIME) (((TIME) > 0) && ((TIME) <= 255))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Bus_Turn_around_Duration
+ * @{
+ */
+#define IS_FMC_TURNAROUND_TIME(TIME) ((TIME) <= 15)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_CLK_Division
+ * @{
+ */
+#define IS_FMC_CLK_DIV(DIV) (((DIV) > 1) && ((DIV) <= 16))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Data_Latency
+ * @{
+ */
+#define IS_FMC_DATA_LATENCY(LATENCY) (((LATENCY) > 1) && ((LATENCY) <= 17))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Access_Mode
+ * @{
+ */
+#define FMC_ACCESS_MODE_A ((uint32_t)0x00000000)
+#define FMC_ACCESS_MODE_B ((uint32_t)0x10000000)
+#define FMC_ACCESS_MODE_C ((uint32_t)0x20000000)
+#define FMC_ACCESS_MODE_D ((uint32_t)0x30000000)
+
+#define IS_FMC_ACCESS_MODE(MODE) (((MODE) == FMC_ACCESS_MODE_A) || \
+ ((MODE) == FMC_ACCESS_MODE_B) || \
+ ((MODE) == FMC_ACCESS_MODE_C) || \
+ ((MODE) == FMC_ACCESS_MODE_D))
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup FMC_NAND_Controller
+ * @{
+ */
+
+/** @defgroup FMC_NAND_Bank
+ * @{
+ */
+#define FMC_NAND_BANK2 ((uint32_t)0x00000010)
+#define FMC_NAND_BANK3 ((uint32_t)0x00000100)
+
+#define IS_FMC_NAND_BANK(BANK) (((BANK) == FMC_NAND_BANK2) || \
+ ((BANK) == FMC_NAND_BANK3))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Wait_feature
+ * @{
+ */
+#define FMC_NAND_PCC_WAIT_FEATURE_DISABLE ((uint32_t)0x00000000)
+#define FMC_NAND_PCC_WAIT_FEATURE_ENABLE ((uint32_t)0x00000002)
+
+#define IS_FMC_WAIT_FEATURE(FEATURE) (((FEATURE) == FMC_NAND_PCC_WAIT_FEATURE_DISABLE) || \
+ ((FEATURE) == FMC_NAND_PCC_WAIT_FEATURE_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_PCR_Memory_Type
+ * @{
+ */
+#define FMC_PCR_MEMORY_TYPE_PCCARD ((uint32_t)0x00000000)
+#define FMC_PCR_MEMORY_TYPE_NAND ((uint32_t)0x00000008)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_NAND_Data_Width
+ * @{
+ */
+#define FMC_NAND_PCC_MEM_BUS_WIDTH_8 ((uint32_t)0x00000000)
+#define FMC_NAND_PCC_MEM_BUS_WIDTH_16 ((uint32_t)0x00000010)
+
+#define IS_FMC_NAND_MEMORY_WIDTH(WIDTH) (((WIDTH) == FMC_NAND_PCC_MEM_BUS_WIDTH_8) || \
+ ((WIDTH) == FMC_NAND_PCC_MEM_BUS_WIDTH_16))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_ECC
+ * @{
+ */
+#define FMC_NAND_ECC_DISABLE ((uint32_t)0x00000000)
+#define FMC_NAND_ECC_ENABLE ((uint32_t)0x00000040)
+
+#define IS_FMC_ECC_STATE(STATE) (((STATE) == FMC_NAND_ECC_DISABLE) || \
+ ((STATE) == FMC_NAND_ECC_ENABLE))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_ECC_Page_Size
+ * @{
+ */
+#define FMC_NAND_ECC_PAGE_SIZE_256BYTE ((uint32_t)0x00000000)
+#define FMC_NAND_ECC_PAGE_SIZE_512BYTE ((uint32_t)0x00020000)
+#define FMC_NAND_ECC_PAGE_SIZE_1024BYTE ((uint32_t)0x00040000)
+#define FMC_NAND_ECC_PAGE_SIZE_2048BYTE ((uint32_t)0x00060000)
+#define FMC_NAND_ECC_PAGE_SIZE_4096BYTE ((uint32_t)0x00080000)
+#define FMC_NAND_ECC_PAGE_SIZE_8192BYTE ((uint32_t)0x000A0000)
+
+#define IS_FMC_ECCPAGE_SIZE(SIZE) (((SIZE) == FMC_NAND_ECC_PAGE_SIZE_256BYTE) || \
+ ((SIZE) == FMC_NAND_ECC_PAGE_SIZE_512BYTE) || \
+ ((SIZE) == FMC_NAND_ECC_PAGE_SIZE_1024BYTE) || \
+ ((SIZE) == FMC_NAND_ECC_PAGE_SIZE_2048BYTE) || \
+ ((SIZE) == FMC_NAND_ECC_PAGE_SIZE_4096BYTE) || \
+ ((SIZE) == FMC_NAND_ECC_PAGE_SIZE_8192BYTE))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_TCLR_Setup_Time
+ * @{
+ */
+#define IS_FMC_TCLR_TIME(TIME) ((TIME) <= 255)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_TAR_Setup_Time
+ * @{
+ */
+#define IS_FMC_TAR_TIME(TIME) ((TIME) <= 255)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Setup_Time
+ * @{
+ */
+#define IS_FMC_SETUP_TIME(TIME) ((TIME) <= 255)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Wait_Setup_Time
+ * @{
+ */
+#define IS_FMC_WAIT_TIME(TIME) ((TIME) <= 255)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Hold_Setup_Time
+ * @{
+ */
+#define IS_FMC_HOLD_TIME(TIME) ((TIME) <= 255)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_HiZ_Setup_Time
+ * @{
+ */
+#define IS_FMC_HIZ_TIME(TIME) ((TIME) <= 255)
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup FMC_NORSRAM_Device_Instance
+ * @{
+ */
+#define IS_FMC_NORSRAM_DEVICE(INSTANCE) ((INSTANCE) == FMC_NORSRAM_DEVICE)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_NORSRAM_EXTENDED_Device_Instance
+ * @{
+ */
+#define IS_FMC_NORSRAM_EXTENDED_DEVICE(INSTANCE) ((INSTANCE) == FMC_NORSRAM_EXTENDED_DEVICE)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_NAND_Device_Instance
+ * @{
+ */
+#define IS_FMC_NAND_DEVICE(INSTANCE) ((INSTANCE) == FMC_NAND_DEVICE)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_PCCARD_Device_Instance
+ * @{
+ */
+#define IS_FMC_PCCARD_DEVICE(INSTANCE) ((INSTANCE) == FMC_PCCARD_DEVICE)
+
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Interrupt_definition
+ * @brief FMC Interrupt definition
+ * @{
+ */
+#define FMC_IT_RISING_EDGE ((uint32_t)0x00000008)
+#define FMC_IT_LEVEL ((uint32_t)0x00000010)
+#define FMC_IT_FALLING_EDGE ((uint32_t)0x00000020)
+#define FMC_IT_REFRESH_ERROR ((uint32_t)0x00004000)
+
+#define IS_FMC_IT(IT) ((((IT) & (uint32_t)0xFFFFBFC7) == 0x00000000) && ((IT) != 0x00000000))
+
+#define IS_FMC_GET_IT(IT) (((IT) == FMC_IT_RISING_EDGE) || \
+ ((IT) == FMC_IT_LEVEL) || \
+ ((IT) == FMC_IT_FALLING_EDGE) || \
+ ((IT) == FMC_IT_REFRESH_ERROR))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Flag_definition
+ * @brief FMC Flag definition
+ * @{
+ */
+#define FMC_FLAG_RISING_EDGE ((uint32_t)0x00000001)
+#define FMC_FLAG_LEVEL ((uint32_t)0x00000002)
+#define FMC_FLAG_FALLING_EDGE ((uint32_t)0x00000004)
+#define FMC_FLAG_FEMPT ((uint32_t)0x00000040)
+
+#define IS_FMC_GET_FLAG(FLAG) (((FLAG) == FMC_FLAG_RISING_EDGE) || \
+ ((FLAG) == FMC_FLAG_LEVEL) || \
+ ((FLAG) == FMC_FLAG_FALLING_EDGE) || \
+ ((FLAG) == FMC_FLAG_FEMPT))
+
+#define IS_FMC_CLEAR_FLAG(FLAG) ((((FLAG) & (uint32_t)0xFFFFFFF8) == 0x00000000) && ((FLAG) != 0x00000000))
+/**
+ * @}
+ */
+
+/* Exported macro ------------------------------------------------------------*/
+
+/** @defgroup FMC_NOR_Macros
+ * @brief macros to handle NOR device enable/disable and read/write operations
+ * @{
+ */
+
+/**
+ * @brief Enable the NORSRAM device access.
+ * @param __INSTANCE__: FMC_NORSRAM Instance
+ * @param __BANK__: FMC_NORSRAM Bank
+ * @retval None
+ */
+#define __FMC_NORSRAM_ENABLE(__INSTANCE__, __BANK__) ((__INSTANCE__)->BTCR[(__BANK__)] |= FMC_BCR1_MBKEN)
+
+/**
+ * @brief Disable the NORSRAM device access.
+ * @param __INSTANCE__: FMC_NORSRAM Instance
+ * @param __BANK__: FMC_NORSRAM Bank
+ * @retval None
+ */
+#define __FMC_NORSRAM_DISABLE(__INSTANCE__, __BANK__) ((__INSTANCE__)->BTCR[(__BANK__)] &= ~FMC_BCR1_MBKEN)
+
+/**
+ * @}
+ */
+
+/** @defgroup FMC_NAND_Macros
+ * @brief macros to handle NAND device enable/disable
+ * @{
+ */
+
+/**
+ * @brief Enable the NAND device access.
+ * @param __INSTANCE__: FMC_NAND Instance
+ * @param __BANK__: FMC_NAND Bank
+ * @retval None
+ */
+#define __FMC_NAND_ENABLE(__INSTANCE__, __BANK__) (((__BANK__) == FMC_NAND_BANK2)? ((__INSTANCE__)->PCR2 |= FMC_PCR2_PBKEN): \
+ ((__INSTANCE__)->PCR3 |= FMC_PCR3_PBKEN))
+
+/**
+ * @brief Disable the NAND device access.
+ * @param __INSTANCE__: FMC_NAND Instance
+ * @param __BANK__: FMC_NAND Bank
+ * @retval None
+ */
+#define __FMC_NAND_DISABLE(__INSTANCE__, __BANK__) (((__BANK__) == FMC_NAND_BANK2)? ((__INSTANCE__)->PCR2 &= ~FMC_PCR2_PBKEN): \
+ ((__INSTANCE__)->PCR3 &= ~FMC_PCR3_PBKEN))
+/**
+ * @}
+ */
+
+/** @defgroup FMC_PCCARD_Macros
+ * @brief macros to handle SRAM read/write operations
+ * @{
+ */
+
+/**
+ * @brief Enable the PCCARD device access.
+ * @param __INSTANCE__: FMC_PCCARD Instance
+ * @retval None
+ */
+#define __FMC_PCCARD_ENABLE(__INSTANCE__) ((__INSTANCE__)->PCR4 |= FMC_PCR4_PBKEN)
+
+/**
+ * @brief Disable the PCCARD device access.
+ * @param __INSTANCE__: FMC_PCCARD Instance
+ * @retval None
+ */
+#define __FMC_PCCARD_DISABLE(__INSTANCE__) ((__INSTANCE__)->PCR4 &= ~FMC_PCR4_PBKEN)
+/**
+ * @}
+ */
+
+/** @defgroup FMC_Interrupt
+ * @brief macros to handle FMC interrupts
+ * @{
+ */
+
+/**
+ * @brief Enable the NAND device interrupt.
+ * @param __INSTANCE__: FMC_NAND Instance
+ * @param __BANK__: FMC_NAND Bank
+ * @param __INTERRUPT__: FMC_NAND interrupt
+ * This parameter can be any combination of the following values:
+ * @arg FMC_IT_RISING_EDGE: Interrupt rising edge.
+ * @arg FMC_IT_LEVEL: Interrupt level.
+ * @arg FMC_IT_FALLING_EDGE: Interrupt falling edge.
+ * @retval None
+ */
+#define __FMC_NAND_ENABLE_IT(__INSTANCE__, __BANK__, __INTERRUPT__) (((__BANK__) == FMC_NAND_BANK2)? ((__INSTANCE__)->SR2 |= (__INTERRUPT__)): \
+ ((__INSTANCE__)->SR3 |= (__INTERRUPT__)))
+
+/**
+ * @brief Disable the NAND device interrupt.
+ * @param __INSTANCE__: FMC_NAND Instance
+ * @param __BANK__: FMC_NAND Bank
+ * @param __INTERRUPT__: FMC_NAND interrupt
+ * This parameter can be any combination of the following values:
+ * @arg FMC_IT_RISING_EDGE: Interrupt rising edge.
+ * @arg FMC_IT_LEVEL: Interrupt level.
+ * @arg FMC_IT_FALLING_EDGE: Interrupt falling edge.
+ * @retval None
+ */
+#define __FMC_NAND_DISABLE_IT(__INSTANCE__, __BANK__, __INTERRUPT__) (((__BANK__) == FMC_NAND_BANK2)? ((__INSTANCE__)->SR2 &= ~(__INTERRUPT__)): \
+ ((__INSTANCE__)->SR3 &= ~(__INTERRUPT__)))
+
+/**
+ * @brief Get flag status of the NAND device.
+ * @param __INSTANCE__: FMC_NAND Instance
+ * @param __BANK__: FMC_NAND Bank
+ * @param __FLAG__: FMC_NAND flag
+ * This parameter can be any combination of the following values:
+ * @arg FMC_FLAG_RISING_EDGE: Interrupt rising edge flag.
+ * @arg FMC_FLAG_LEVEL: Interrupt level edge flag.
+ * @arg FMC_FLAG_FALLING_EDGE: Interrupt falling edge flag.
+ * @arg FMC_FLAG_FEMPT: FIFO empty flag.
+ * @retval The state of FLAG (SET or RESET).
+ */
+#define __FMC_NAND_GET_FLAG(__INSTANCE__, __BANK__, __FLAG__) (((__BANK__) == FMC_NAND_BANK2)? (((__INSTANCE__)->SR2 &(__FLAG__)) == (__FLAG__)): \
+ (((__INSTANCE__)->SR3 &(__FLAG__)) == (__FLAG__)))
+/**
+ * @brief Clear flag status of the NAND device.
+ * @param __INSTANCE__: FMC_NAND Instance
+ * @param __BANK__: FMC_NAND Bank
+ * @param __FLAG__: FMC_NAND flag
+ * This parameter can be any combination of the following values:
+ * @arg FMC_FLAG_RISING_EDGE: Interrupt rising edge flag.
+ * @arg FMC_FLAG_LEVEL: Interrupt level edge flag.
+ * @arg FMC_FLAG_FALLING_EDGE: Interrupt falling edge flag.
+ * @arg FMC_FLAG_FEMPT: FIFO empty flag.
+ * @retval None
+ */
+#define __FMC_NAND_CLEAR_FLAG(__INSTANCE__, __BANK__, __FLAG__) (((__BANK__) == FMC_NAND_BANK2)? ((__INSTANCE__)->SR2 &= ~(__FLAG__)): \
+ ((__INSTANCE__)->SR3 &= ~(__FLAG__)))
+/**
+ * @brief Enable the PCCARD device interrupt.
+ * @param __INSTANCE__: FMC_PCCARD Instance
+ * @param __INTERRUPT__: FMC_PCCARD interrupt
+ * This parameter can be any combination of the following values:
+ * @arg FMC_IT_RISING_EDGE: Interrupt rising edge.
+ * @arg FMC_IT_LEVEL: Interrupt level.
+ * @arg FMC_IT_FALLING_EDGE: Interrupt falling edge.
+ * @retval None
+ */
+#define __FMC_PCCARD_ENABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->SR4 |= (__INTERRUPT__))
+
+/**
+ * @brief Disable the PCCARD device interrupt.
+ * @param __INSTANCE__: FMC_PCCARD Instance
+ * @param __INTERRUPT__: FMC_PCCARD interrupt
+ * This parameter can be any combination of the following values:
+ * @arg FMC_IT_RISING_EDGE: Interrupt rising edge.
+ * @arg FMC_IT_LEVEL: Interrupt level.
+ * @arg FMC_IT_FALLING_EDGE: Interrupt falling edge.
+ * @retval None
+ */
+#define __FMC_PCCARD_DISABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->SR4 &= ~(__INTERRUPT__))
+
+/**
+ * @brief Get flag status of the PCCARD device.
+ * @param __INSTANCE__: FMC_PCCARD Instance
+ * @param __FLAG__: FMC_PCCARD flag
+ * This parameter can be any combination of the following values:
+ * @arg FMC_FLAG_RISING_EDGE: Interrupt rising edge flag.
+ * @arg FMC_FLAG_LEVEL: Interrupt level edge flag.
+ * @arg FMC_FLAG_FALLING_EDGE: Interrupt falling edge flag.
+ * @arg FMC_FLAG_FEMPT: FIFO empty flag.
+ * @retval The state of FLAG (SET or RESET).
+ */
+#define __FMC_PCCARD_GET_FLAG(__INSTANCE__, __FLAG__) (((__INSTANCE__)->SR4 &(__FLAG__)) == (__FLAG__))
+
+/**
+ * @brief Clear flag status of the PCCARD device.
+ * @param __INSTANCE__: FMC_PCCARD Instance
+ * @param __FLAG__: FMC_PCCARD flag
+ * This parameter can be any combination of the following values:
+ * @arg FMC_FLAG_RISING_EDGE: Interrupt rising edge flag.
+ * @arg FMC_FLAG_LEVEL: Interrupt level edge flag.
+ * @arg FMC_FLAG_FALLING_EDGE: Interrupt falling edge flag.
+ * @arg FMC_FLAG_FEMPT: FIFO empty flag.
+ * @retval None
+ */
+#define __FMC_PCCARD_CLEAR_FLAG(__INSTANCE__, __FLAG__) ((__INSTANCE__)->SR4 &= ~(__FLAG__))
+
+/**
+ * @}
+ */
+
+/* Exported functions --------------------------------------------------------*/
+
+/* FMC_NORSRAM Controller functions *******************************************/
+/* Initialization/de-initialization functions */
+HAL_StatusTypeDef FMC_NORSRAM_Init(FMC_NORSRAM_TypeDef *Device, FMC_NORSRAM_InitTypeDef *Init);
+HAL_StatusTypeDef FMC_NORSRAM_Timing_Init(FMC_NORSRAM_TypeDef *Device, FMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank);
+HAL_StatusTypeDef FMC_NORSRAM_Extended_Timing_Init(FMC_NORSRAM_EXTENDED_TypeDef *Device, FMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank, uint32_t ExtendedMode);
+HAL_StatusTypeDef FMC_NORSRAM_DeInit(FMC_NORSRAM_TypeDef *Device, FMC_NORSRAM_EXTENDED_TypeDef *ExDevice, uint32_t Bank);
+
+/* FMC_NORSRAM Control functions */
+HAL_StatusTypeDef FMC_NORSRAM_WriteOperation_Enable(FMC_NORSRAM_TypeDef *Device, uint32_t Bank);
+HAL_StatusTypeDef FMC_NORSRAM_WriteOperation_Disable(FMC_NORSRAM_TypeDef *Device, uint32_t Bank);
+
+/* FMC_NAND Controller functions **********************************************/
+/* Initialization/de-initialization functions */
+HAL_StatusTypeDef FMC_NAND_Init(FMC_NAND_TypeDef *Device, FMC_NAND_InitTypeDef *Init);
+HAL_StatusTypeDef FMC_NAND_CommonSpace_Timing_Init(FMC_NAND_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank);
+HAL_StatusTypeDef FMC_NAND_AttributeSpace_Timing_Init(FMC_NAND_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank);
+HAL_StatusTypeDef FMC_NAND_DeInit(FMC_NAND_TypeDef *Device, uint32_t Bank);
+
+/* FMC_NAND Control functions */
+HAL_StatusTypeDef FMC_NAND_ECC_Enable(FMC_NAND_TypeDef *Device, uint32_t Bank);
+HAL_StatusTypeDef FMC_NAND_ECC_Disable(FMC_NAND_TypeDef *Device, uint32_t Bank);
+HAL_StatusTypeDef FMC_NAND_GetECC(FMC_NAND_TypeDef *Device, uint32_t *ECCval, uint32_t Bank, uint32_t Timeout);
+
+/* FMC_PCCARD Controller functions ********************************************/
+/* Initialization/de-initialization functions */
+HAL_StatusTypeDef FMC_PCCARD_Init(FMC_PCCARD_TypeDef *Device, FMC_PCCARD_InitTypeDef *Init);
+HAL_StatusTypeDef FMC_PCCARD_CommonSpace_Timing_Init(FMC_PCCARD_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing);
+HAL_StatusTypeDef FMC_PCCARD_AttributeSpace_Timing_Init(FMC_PCCARD_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing);
+HAL_StatusTypeDef FMC_PCCARD_IOSpace_Timing_Init(FMC_PCCARD_TypeDef *Device, FMC_NAND_PCC_TimingTypeDef *Timing);
+HAL_StatusTypeDef FMC_PCCARD_DeInit(FMC_PCCARD_TypeDef *Device);
+
+#endif /* STM32F302xE || STM32F303xE || STM32F398xx */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F3xx_LL_FMC_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/