Ricardo Benitez
meh
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_F091RC/stm32f0xx_hal_smartcard.h
- Revision:
- 108:34e6b704fe68
- Parent:
- 93:e188a91d3eaa
--- a/TARGET_NUCLEO_F091RC/stm32f0xx_hal_smartcard.h Wed Sep 16 15:32:31 2015 +0100
+++ b/TARGET_NUCLEO_F091RC/stm32f0xx_hal_smartcard.h Fri Oct 02 07:35:07 2015 +0200
@@ -2,13 +2,13 @@
******************************************************************************
* @file stm32f0xx_hal_smartcard.h
* @author MCD Application Team
- * @version V1.2.0
- * @date 11-December-2014
+ * @version V1.3.0
+ * @date 26-June-2015
* @brief Header file of SMARTCARD HAL module.
******************************************************************************
* @attention
*
- * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2>
+ * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
@@ -32,7 +32,7 @@
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
- ******************************************************************************
+ ******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
@@ -54,23 +54,22 @@
/** @addtogroup SMARTCARD
* @{
- */
+ */
-/* Exported types ------------------------------------------------------------*/
+/* Exported types ------------------------------------------------------------*/
/** @defgroup SMARTCARD_Exported_Types SMARTCARD Exported Types
* @{
- */
-
+ */
-/**
- * @brief SMARTCARD Init Structure definition
- */
+/**
+ * @brief SMARTCARD Init Structure definition
+ */
typedef struct
{
uint32_t BaudRate; /*!< Configures the SmartCard communication baud rate.
The baud rate register is computed using the following formula:
Baud Rate Register = ((PCLKx) / ((hsmartcard->Init.BaudRate))) */
-
+
uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
This parameter @ref SMARTCARD_Word_Length can only be set to 9 (8 data + 1 parity bits). */
@@ -82,7 +81,7 @@
@note The parity is enabled by default (PCE is forced to 1).
Since the WordLength is forced to 8 bits + parity, M is
forced to 1 and the parity bit is the 9th bit. */
-
+
uint16_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
This parameter can be a value of @ref SMARTCARD_Mode */
@@ -95,85 +94,85 @@
uint16_t CLKLastBit; /*!< Specifies whether the clock pulse corresponding to the last transmitted
data bit (MSB) has to be output on the SCLK pin in synchronous mode.
This parameter can be a value of @ref SMARTCARD_Last_Bit */
-
+
uint16_t OneBitSampling; /*!< Specifies whether a single sample or three samples' majority vote is selected.
Selecting the single sample method increases the receiver tolerance to clock
deviations. This parameter can be a value of @ref SMARTCARD_OneBit_Sampling. */
uint8_t Prescaler; /*!< Specifies the SmartCard Prescaler */
-
+
uint8_t GuardTime; /*!< Specifies the SmartCard Guard Time */
-
+
uint16_t NACKEnable; /*!< Specifies whether the SmartCard NACK transmission is enabled
in case of parity error.
- This parameter can be a value of @ref SMARTCARD_NACK_Enable */
-
- uint32_t TimeOutEnable; /*!< Specifies whether the receiver timeout is enabled.
+ This parameter can be a value of @ref SMARTCARD_NACK_Enable */
+
+ uint32_t TimeOutEnable; /*!< Specifies whether the receiver timeout is enabled.
This parameter can be a value of @ref SMARTCARD_Timeout_Enable*/
-
- uint32_t TimeOutValue; /*!< Specifies the receiver time out value in number of baud blocks:
- it is used to implement the Character Wait Time (CWT) and
- Block Wait Time (BWT). It is coded over 24 bits. */
-
+
+ uint32_t TimeOutValue; /*!< Specifies the receiver time out value in number of baud blocks:
+ it is used to implement the Character Wait Time (CWT) and
+ Block Wait Time (BWT). It is coded over 24 bits. */
+
uint8_t BlockLength; /*!< Specifies the SmartCard Block Length in T=1 Reception mode.
- This parameter can be any value from 0x0 to 0xFF */
-
+ This parameter can be any value from 0x0 to 0xFF */
+
uint8_t AutoRetryCount; /*!< Specifies the SmartCard auto-retry count (number of retries in
- receive and transmit mode). When set to 0, retransmission is
+ receive and transmit mode). When set to 0, retransmission is
disabled. Otherwise, its maximum value is 7 (before signalling
- an error) */
-
+ an error) */
+
}SMARTCARD_InitTypeDef;
-/**
- * @brief SMARTCARD advanced features initalization structure definition
+/**
+ * @brief SMARTCARD advanced features initalization structure definition
*/
-typedef struct
+typedef struct
{
uint32_t AdvFeatureInit; /*!< Specifies which advanced SMARTCARD features is initialized. Several
- advanced features may be initialized at the same time. This parameter
- can be a value of @ref SMARTCARD_Advanced_Features_Initialization_Type */
+ advanced features may be initialized at the same time. This parameter
+ can be a value of @ref SMARTCARD_Advanced_Features_Initialization_Type */
uint32_t TxPinLevelInvert; /*!< Specifies whether the TX pin active level is inverted.
This parameter can be a value of @ref SMARTCARD_Tx_Inv */
-
+
uint32_t RxPinLevelInvert; /*!< Specifies whether the RX pin active level is inverted.
This parameter can be a value of @ref SMARTCARD_Rx_Inv */
uint32_t DataInvert; /*!< Specifies whether data are inverted (positive/direct logic
vs negative/inverted logic).
This parameter can be a value of @ref SMARTCARD_Data_Inv */
-
- uint32_t Swap; /*!< Specifies whether TX and RX pins are swapped.
+
+ uint32_t Swap; /*!< Specifies whether TX and RX pins are swapped.
This parameter can be a value of @ref SMARTCARD_Rx_Tx_Swap */
-
- uint32_t OverrunDisable; /*!< Specifies whether the reception overrun detection is disabled.
+
+ uint32_t OverrunDisable; /*!< Specifies whether the reception overrun detection is disabled.
This parameter can be a value of @ref SMARTCARD_Overrun_Disable */
-
- uint32_t DMADisableonRxError; /*!< Specifies whether the DMA is disabled in case of reception error.
+
+ uint32_t DMADisableonRxError; /*!< Specifies whether the DMA is disabled in case of reception error.
This parameter can be a value of @ref SMARTCARD_DMA_Disable_on_Rx_Error */
-
- uint32_t MSBFirst; /*!< Specifies whether MSB is sent first on UART line.
+
+ uint32_t MSBFirst; /*!< Specifies whether MSB is sent first on UART line.
This parameter can be a value of @ref SMARTCARD_MSB_First */
}SMARTCARD_AdvFeatureInitTypeDef;
-/**
- * @brief HAL State structures definition
- */
+/**
+ * @brief HAL State structures definition
+ */
typedef enum
{
HAL_SMARTCARD_STATE_RESET = 0x00, /*!< Peripheral is not initialized */
HAL_SMARTCARD_STATE_READY = 0x01, /*!< Peripheral Initialized and ready for use */
- HAL_SMARTCARD_STATE_BUSY = 0x02, /*!< an internal process is ongoing */
+ HAL_SMARTCARD_STATE_BUSY = 0x02, /*!< an internal process is ongoing */
HAL_SMARTCARD_STATE_BUSY_TX = 0x12, /*!< Data Transmission process is ongoing */
HAL_SMARTCARD_STATE_BUSY_RX = 0x22, /*!< Data Reception process is ongoing */
- HAL_SMARTCARD_STATE_BUSY_TX_RX = 0x32, /*!< Data Transmission and Reception process is ongoing */
+ HAL_SMARTCARD_STATE_BUSY_TX_RX = 0x32, /*!< Data Transmission and Reception process is ongoing */
HAL_SMARTCARD_STATE_TIMEOUT = 0x03, /*!< Timeout state */
HAL_SMARTCARD_STATE_ERROR = 0x04 /*!< Error */
}HAL_SMARTCARD_StateTypeDef;
-/**
- * @brief SMARTCARD clock sources
+/**
+ * @brief SMARTCARD clock sources
*/
typedef enum
{
@@ -181,43 +180,43 @@
SMARTCARD_CLOCKSOURCE_HSI = 0x02, /*!< HSI clock source */
SMARTCARD_CLOCKSOURCE_SYSCLK = 0x04, /*!< SYSCLK clock source */
SMARTCARD_CLOCKSOURCE_LSE = 0x08, /*!< LSE clock source */
- SMARTCARD_CLOCKSOURCE_UNDEFINED = 0x10 /*!< undefined clock source */
+ SMARTCARD_CLOCKSOURCE_UNDEFINED = 0x10 /*!< undefined clock source */
}SMARTCARD_ClockSourceTypeDef;
-/**
- * @brief SMARTCARD handle Structure definition
- */
+/**
+ * @brief SMARTCARD handle Structure definition
+ */
typedef struct
{
USART_TypeDef *Instance; /*!< USART registers base address */
-
+
SMARTCARD_InitTypeDef Init; /*!< SmartCard communication parameters */
-
+
SMARTCARD_AdvFeatureInitTypeDef AdvancedInit; /*!< SmartCard advanced features initialization parameters */
-
+
uint8_t *pTxBuffPtr; /*!< Pointer to SmartCard Tx transfer Buffer */
-
+
uint16_t TxXferSize; /*!< SmartCard Tx Transfer size */
-
+
uint16_t TxXferCount; /*!< SmartCard Tx Transfer Counter */
-
+
uint8_t *pRxBuffPtr; /*!< Pointer to SmartCard Rx transfer Buffer */
-
+
uint16_t RxXferSize; /*!< SmartCard Rx Transfer size */
-
+
uint16_t RxXferCount; /*!< SmartCard Rx Transfer Counter */
-
+
DMA_HandleTypeDef *hdmatx; /*!< SmartCard Tx DMA Handle parameters */
-
+
DMA_HandleTypeDef *hdmarx; /*!< SmartCard Rx DMA Handle parameters */
-
+
HAL_LockTypeDef Lock; /*!< Locking object */
-
- HAL_SMARTCARD_StateTypeDef State; /*!< SmartCard communication state */
-
+
+ __IO HAL_SMARTCARD_StateTypeDef State; /*!< SmartCard communication state */
+
__IO uint32_t ErrorCode; /*!< SmartCard Error code
This parameter can be a value of @ref SMARTCARD_Error */
-
+
}SMARTCARD_HandleTypeDef;
/**
@@ -225,11 +224,11 @@
*/
/* Exported constants --------------------------------------------------------*/
-/** @defgroup SMARTCARD_Exported_Constants SMARTCARD Exported constants
+/** @defgroup SMARTCARD_Exported_Constants SMARTCARD Exported Constants
* @{
*/
-/** @defgroup SMARTCARD_Error SMARTCARD Error
+/** @defgroup SMARTCARD_Error SMARTCARD Error
* @{
*/
#define HAL_SMARTCARD_ERROR_NONE ((uint32_t)0x00000000) /*!< No error */
@@ -243,73 +242,64 @@
* @}
*/
-/** @defgroup SMARTCARD_Word_Length SMARTCARD Word Length
+/** @defgroup SMARTCARD_Word_Length SMARTCARD Word Length
* @{
*/
-#define SMARTCARD_WORDLENGTH_9B ((uint32_t)USART_CR1_M0)
-#define IS_SMARTCARD_WORD_LENGTH(LENGTH) ((LENGTH) == SMARTCARD_WORDLENGTH_9B)
+#define SMARTCARD_WORDLENGTH_9B ((uint32_t)USART_CR1_M0) /*!< SMARTCARD frame length */
/**
* @}
*/
-
-/** @defgroup SMARTCARD_Stop_Bits SMARTCARD Stop Bits
+
+/** @defgroup SMARTCARD_Stop_Bits SMARTCARD Stop Bits
* @{
*/
-#define SMARTCARD_STOPBITS_1_5 ((uint32_t)(USART_CR2_STOP))
-#define IS_SMARTCARD_STOPBITS(STOPBITS) ((STOPBITS) == SMARTCARD_STOPBITS_1_5)
+#define SMARTCARD_STOPBITS_1_5 USART_CR2_STOP /*!< SMARTCARD frame with 1.5 stop bits */
/**
* @}
- */
+ */
-/** @defgroup SMARTCARD_Parity SMARTCARD Parity
+/** @defgroup SMARTCARD_Parity SMARTCARD Parity
* @{
- */
-#define SMARTCARD_PARITY_EVEN ((uint16_t)USART_CR1_PCE)
-#define SMARTCARD_PARITY_ODD ((uint16_t)(USART_CR1_PCE | USART_CR1_PS))
-#define IS_SMARTCARD_PARITY(PARITY) (((PARITY) == SMARTCARD_PARITY_EVEN) || \
- ((PARITY) == SMARTCARD_PARITY_ODD))
-/**
- * @}
- */
-
-/** @defgroup SMARTCARD_Mode SMARTCARD Transfer Mode
- * @{
- */
-#define SMARTCARD_MODE_RX ((uint16_t)USART_CR1_RE)
-#define SMARTCARD_MODE_TX ((uint16_t)USART_CR1_TE)
-#define SMARTCARD_MODE_TX_RX ((uint16_t)(USART_CR1_TE |USART_CR1_RE))
-#define IS_SMARTCARD_MODE(MODE) ((((MODE) & (uint16_t)0xFFF3) == 0x00) && ((MODE) != (uint16_t)0x00))
+ */
+#define SMARTCARD_PARITY_EVEN ((uint32_t)USART_CR1_PCE) /*!< SMARTCARD frame even parity */
+#define SMARTCARD_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS)) /*!< SMARTCARD frame odd parity */
/**
* @}
*/
-/** @defgroup SMARTCARD_Clock_Polarity SMARTCARD Clock Polarity
+/** @defgroup SMARTCARD_Mode SMARTCARD Transfer Mode
* @{
*/
-#define SMARTCARD_POLARITY_LOW ((uint16_t)0x0000)
-#define SMARTCARD_POLARITY_HIGH ((uint16_t)USART_CR2_CPOL)
-#define IS_SMARTCARD_POLARITY(CPOL) (((CPOL) == SMARTCARD_POLARITY_LOW) || ((CPOL) == SMARTCARD_POLARITY_HIGH))
+#define SMARTCARD_MODE_RX ((uint32_t)USART_CR1_RE) /*!< SMARTCARD RX mode */
+#define SMARTCARD_MODE_TX ((uint32_t)USART_CR1_TE) /*!< SMARTCARD TX mode */
+#define SMARTCARD_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE)) /*!< SMARTCARD RX and TX mode */
/**
* @}
- */
+ */
+
+/** @defgroup SMARTCARD_Clock_Polarity SMARTCARD Clock Polarity
+ * @{
+ */
+#define SMARTCARD_POLARITY_LOW ((uint32_t)0x00000000) /*!< SMARTCARD frame low polarity */
+#define SMARTCARD_POLARITY_HIGH ((uint32_t)USART_CR2_CPOL) /*!< SMARTCARD frame high polarity */
+/**
+ * @}
+ */
/** @defgroup SMARTCARD_Clock_Phase SMARTCARD Clock Phase
* @{
*/
-#define SMARTCARD_PHASE_1EDGE ((uint16_t)0x0000)
-#define SMARTCARD_PHASE_2EDGE ((uint16_t)USART_CR2_CPHA)
-#define IS_SMARTCARD_PHASE(CPHA) (((CPHA) == SMARTCARD_PHASE_1EDGE) || ((CPHA) == SMARTCARD_PHASE_2EDGE))
+#define SMARTCARD_PHASE_1EDGE ((uint32_t)0x00000000) /*!< SMARTCARD frame phase on first clock transition */
+#define SMARTCARD_PHASE_2EDGE ((uint32_t)USART_CR2_CPHA) /*!< SMARTCARD frame phase on second clock transition */
/**
* @}
*/
-/** @defgroup SMARTCARD_Last_Bit SMARTCARD Last Bit
+/** @defgroup SMARTCARD_Last_Bit SMARTCARD Last Bit
* @{
*/
-#define SMARTCARD_LASTBIT_DISABLED ((uint16_t)0x0000)
-#define SMARTCARD_LASTBIT_ENABLED ((uint16_t)USART_CR2_LBCL)
-#define IS_SMARTCARD_LASTBIT(LASTBIT) (((LASTBIT) == SMARTCARD_LASTBIT_DISABLED) || \
- ((LASTBIT) == SMARTCARD_LASTBIT_ENABLED))
+#define SMARTCARD_LASTBIT_DISABLE ((uint32_t)0x00000000) /*!< SMARTCARD frame last data bit clock pulse not output to SCLK pin */
+#define SMARTCARD_LASTBIT_ENABLE ((uint32_t)USART_CR2_LBCL) /*!< SMARTCARD frame last data bit clock pulse output to SCLK pin */
/**
* @}
*/
@@ -317,56 +307,42 @@
/** @defgroup SMARTCARD_OneBit_Sampling SMARTCARD One Bit Sampling Method
* @{
*/
-#define SMARTCARD_ONEBIT_SAMPLING_DISABLED ((uint16_t)0x0000)
-#define SMARTCARD_ONEBIT_SAMPLING_ENABLED ((uint16_t)USART_CR3_ONEBIT)
-#define IS_SMARTCARD_ONEBIT_SAMPLING(ONEBIT) (((ONEBIT) == SMARTCARD_ONEBIT_SAMPLING_DISABLED) || \
- ((ONEBIT) == SMARTCARD_ONEBIT_SAMPLING_ENABLED))
+#define SMARTCARD_ONE_BIT_SAMPLE_DISABLE ((uint32_t)0x00000000) /*!< SMARTCARD frame one-bit sample disabled */
+#define SMARTCARD_ONE_BIT_SAMPLE_ENABLE ((uint32_t)USART_CR3_ONEBIT) /*!< SMARTCARD frame one-bit sample enabled */
/**
* @}
- */
+ */
-/** @defgroup SMARTCARD_NACK_Enable SMARTCARD NACK Enable
+/** @defgroup SMARTCARD_NACK_Enable SMARTCARD NACK Enable
* @{
*/
-#define SMARTCARD_NACK_ENABLED ((uint16_t)USART_CR3_NACK)
-#define SMARTCARD_NACK_DISABLED ((uint16_t)0x0000)
-#define IS_SMARTCARD_NACK(NACK) (((NACK) == SMARTCARD_NACK_ENABLED) || \
- ((NACK) == SMARTCARD_NACK_DISABLED))
+#define SMARTCARD_NACK_ENABLE ((uint32_t)USART_CR3_NACK) /*!< SMARTCARD NACK transmission disabled */
+#define SMARTCARD_NACK_DISABLE ((uint32_t)0x00000000) /*!< SMARTCARD NACK transmission enabled */
/**
* @}
*/
-/** @defgroup SMARTCARD_Timeout_Enable SMARTCARD Timeout Enable
+/** @defgroup SMARTCARD_Timeout_Enable SMARTCARD Timeout Enable
* @{
*/
-#define SMARTCARD_TIMEOUT_DISABLED ((uint32_t)0x00000000)
-#define SMARTCARD_TIMEOUT_ENABLED ((uint32_t)USART_CR2_RTOEN)
-#define IS_SMARTCARD_TIMEOUT(TIMEOUT) (((TIMEOUT) == SMARTCARD_TIMEOUT_DISABLED) || \
- ((TIMEOUT) == SMARTCARD_TIMEOUT_ENABLED))
+#define SMARTCARD_TIMEOUT_DISABLE ((uint32_t)0x00000000) /*!< SMARTCARD receiver timeout disabled */
+#define SMARTCARD_TIMEOUT_ENABLE ((uint32_t)USART_CR2_RTOEN) /*!< SMARTCARD receiver timeout enabled */
/**
* @}
*/
-
+
/** @defgroup SMARTCARD_Advanced_Features_Initialization_Type SMARTCARD advanced feature initialization type
* @{
*/
-#define SMARTCARD_ADVFEATURE_NO_INIT ((uint32_t)0x00000000)
-#define SMARTCARD_ADVFEATURE_TXINVERT_INIT ((uint32_t)0x00000001)
-#define SMARTCARD_ADVFEATURE_RXINVERT_INIT ((uint32_t)0x00000002)
-#define SMARTCARD_ADVFEATURE_DATAINVERT_INIT ((uint32_t)0x00000004)
-#define SMARTCARD_ADVFEATURE_SWAP_INIT ((uint32_t)0x00000008)
-#define SMARTCARD_ADVFEATURE_RXOVERRUNDISABLE_INIT ((uint32_t)0x00000010)
-#define SMARTCARD_ADVFEATURE_DMADISABLEONERROR_INIT ((uint32_t)0x00000020)
-#define SMARTCARD_ADVFEATURE_MSBFIRST_INIT ((uint32_t)0x00000080)
-#define IS_SMARTCARD_ADVFEATURE_INIT(INIT) ((INIT) <= (SMARTCARD_ADVFEATURE_NO_INIT | \
- SMARTCARD_ADVFEATURE_TXINVERT_INIT | \
- SMARTCARD_ADVFEATURE_RXINVERT_INIT | \
- SMARTCARD_ADVFEATURE_DATAINVERT_INIT | \
- SMARTCARD_ADVFEATURE_SWAP_INIT | \
- SMARTCARD_ADVFEATURE_RXOVERRUNDISABLE_INIT | \
- SMARTCARD_ADVFEATURE_DMADISABLEONERROR_INIT | \
- SMARTCARD_ADVFEATURE_MSBFIRST_INIT))
+#define SMARTCARD_ADVFEATURE_NO_INIT ((uint32_t)0x00000000) /*!< No advanced feature initialization */
+#define SMARTCARD_ADVFEATURE_TXINVERT_INIT ((uint32_t)0x00000001) /*!< TX pin active level inversion */
+#define SMARTCARD_ADVFEATURE_RXINVERT_INIT ((uint32_t)0x00000002) /*!< RX pin active level inversion */
+#define SMARTCARD_ADVFEATURE_DATAINVERT_INIT ((uint32_t)0x00000004) /*!< Binary data inversion */
+#define SMARTCARD_ADVFEATURE_SWAP_INIT ((uint32_t)0x00000008) /*!< TX/RX pins swap */
+#define SMARTCARD_ADVFEATURE_RXOVERRUNDISABLE_INIT ((uint32_t)0x00000010) /*!< RX overrun disable */
+#define SMARTCARD_ADVFEATURE_DMADISABLEONERROR_INIT ((uint32_t)0x00000020) /*!< DMA disable on Reception Error */
+#define SMARTCARD_ADVFEATURE_MSBFIRST_INIT ((uint32_t)0x00000080) /*!< Most significant bit sent/received first */
/**
* @}
*/
@@ -374,10 +350,8 @@
/** @defgroup SMARTCARD_Tx_Inv SMARTCARD advanced feature TX pin active level inversion
* @{
*/
-#define SMARTCARD_ADVFEATURE_TXINV_DISABLE ((uint32_t)0x00000000)
-#define SMARTCARD_ADVFEATURE_TXINV_ENABLE ((uint32_t)USART_CR2_TXINV)
-#define IS_SMARTCARD_ADVFEATURE_TXINV(TXINV) (((TXINV) == SMARTCARD_ADVFEATURE_TXINV_DISABLE) || \
- ((TXINV) == SMARTCARD_ADVFEATURE_TXINV_ENABLE))
+#define SMARTCARD_ADVFEATURE_TXINV_DISABLE ((uint32_t)0x00000000) /*!< TX pin active level inversion disable */
+#define SMARTCARD_ADVFEATURE_TXINV_ENABLE ((uint32_t)USART_CR2_TXINV) /*!< TX pin active level inversion enable */
/**
* @}
*/
@@ -385,86 +359,75 @@
/** @defgroup SMARTCARD_Rx_Inv SMARTCARD advanced feature RX pin active level inversion
* @{
*/
-#define SMARTCARD_ADVFEATURE_RXINV_DISABLE ((uint32_t)0x00000000)
-#define SMARTCARD_ADVFEATURE_RXINV_ENABLE ((uint32_t)USART_CR2_RXINV)
-#define IS_SMARTCARD_ADVFEATURE_RXINV(RXINV) (((RXINV) == SMARTCARD_ADVFEATURE_RXINV_DISABLE) || \
- ((RXINV) == SMARTCARD_ADVFEATURE_RXINV_ENABLE))
+#define SMARTCARD_ADVFEATURE_RXINV_DISABLE ((uint32_t)0x00000000) /*!< RX pin active level inversion disable */
+#define SMARTCARD_ADVFEATURE_RXINV_ENABLE ((uint32_t)USART_CR2_RXINV) /*!< RX pin active level inversion enable */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Data_Inv SMARTCARD advanced feature Binary Data inversion
+ * @{
+ */
+#define SMARTCARD_ADVFEATURE_DATAINV_DISABLE ((uint32_t)0x00000000) /*!< Binary data inversion disable */
+#define SMARTCARD_ADVFEATURE_DATAINV_ENABLE ((uint32_t)USART_CR2_DATAINV) /*!< Binary data inversion enable */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Rx_Tx_Swap SMARTCARD advanced feature RX TX pins swap
+ * @{
+ */
+#define SMARTCARD_ADVFEATURE_SWAP_DISABLE ((uint32_t)0x00000000) /*!< TX/RX pins swap disable */
+#define SMARTCARD_ADVFEATURE_SWAP_ENABLE ((uint32_t)USART_CR2_SWAP) /*!< TX/RX pins swap enable */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Overrun_Disable SMARTCARD advanced feature Overrun Disable
+ * @{
+ */
+#define SMARTCARD_ADVFEATURE_OVERRUN_ENABLE ((uint32_t)0x00000000) /*!< RX overrun enable */
+#define SMARTCARD_ADVFEATURE_OVERRUN_DISABLE ((uint32_t)USART_CR3_OVRDIS) /*!< RX overrun disable */
/**
* @}
*/
-/** @defgroup SMARTCARD_Data_Inv SMARTCARD advanced feature Binary Data inversion
+/** @defgroup SMARTCARD_DMA_Disable_on_Rx_Error SMARTCARD advanced feature DMA Disable on Rx Error
* @{
*/
-#define SMARTCARD_ADVFEATURE_DATAINV_DISABLE ((uint32_t)0x00000000)
-#define SMARTCARD_ADVFEATURE_DATAINV_ENABLE ((uint32_t)USART_CR2_DATAINV)
-#define IS_SMARTCARD_ADVFEATURE_DATAINV(DATAINV) (((DATAINV) == SMARTCARD_ADVFEATURE_DATAINV_DISABLE) || \
- ((DATAINV) == SMARTCARD_ADVFEATURE_DATAINV_ENABLE))
-/**
- * @}
- */
-
-/** @defgroup SMARTCARD_Rx_Tx_Swap SMARTCARD advanced feature RX TX pins swap
- * @{
- */
-#define SMARTCARD_ADVFEATURE_SWAP_DISABLE ((uint32_t)0x00000000)
-#define SMARTCARD_ADVFEATURE_SWAP_ENABLE ((uint32_t)USART_CR2_SWAP)
-#define IS_SMARTCARD_ADVFEATURE_SWAP(SWAP) (((SWAP) == SMARTCARD_ADVFEATURE_SWAP_DISABLE) || \
- ((SWAP) == SMARTCARD_ADVFEATURE_SWAP_ENABLE))
+#define SMARTCARD_ADVFEATURE_DMA_ENABLEONRXERROR ((uint32_t)0x00000000) /*!< DMA enable on Reception Error */
+#define SMARTCARD_ADVFEATURE_DMA_DISABLEONRXERROR ((uint32_t)USART_CR3_DDRE) /*!< DMA disable on Reception Error */
/**
* @}
- */
-
-/** @defgroup SMARTCARD_Overrun_Disable SMARTCARD advanced feature Overrun Disable
- * @{
*/
-#define SMARTCARD_ADVFEATURE_OVERRUN_ENABLE ((uint32_t)0x00000000)
-#define SMARTCARD_ADVFEATURE_OVERRUN_DISABLE ((uint32_t)USART_CR3_OVRDIS)
-#define IS_SMARTCARD_OVERRUN(OVERRUN) (((OVERRUN) == SMARTCARD_ADVFEATURE_OVERRUN_ENABLE) || \
- ((OVERRUN) == SMARTCARD_ADVFEATURE_OVERRUN_DISABLE))
-/**
- * @}
- */
-
-/** @defgroup SMARTCARD_DMA_Disable_on_Rx_Error SMARTCARD advanced feature DMA Disable on Rx Error
- * @{
- */
-#define SMARTCARD_ADVFEATURE_DMA_ENABLEONRXERROR ((uint32_t)0x00000000)
-#define SMARTCARD_ADVFEATURE_DMA_DISABLEONRXERROR ((uint32_t)USART_CR3_DDRE)
-#define IS_SMARTCARD_ADVFEATURE_DMAONRXERROR(DMA) (((DMA) == SMARTCARD_ADVFEATURE_DMA_ENABLEONRXERROR) || \
- ((DMA) == SMARTCARD_ADVFEATURE_DMA_DISABLEONRXERROR))
-/**
- * @}
- */
/** @defgroup SMARTCARD_MSB_First SMARTCARD advanced feature MSB first
* @{
*/
-#define SMARTCARD_ADVFEATURE_MSBFIRST_DISABLE ((uint32_t)0x00000000)
-#define SMARTCARD_ADVFEATURE_MSBFIRST_ENABLE ((uint32_t)USART_CR2_MSBFIRST)
-#define IS_SMARTCARD_ADVFEATURE_MSBFIRST(MSBFIRST) (((MSBFIRST) == SMARTCARD_ADVFEATURE_MSBFIRST_DISABLE) || \
- ((MSBFIRST) == SMARTCARD_ADVFEATURE_MSBFIRST_ENABLE))
+#define SMARTCARD_ADVFEATURE_MSBFIRST_DISABLE ((uint32_t)0x00000000) /*!< Most significant bit sent/received first disable */
+#define SMARTCARD_ADVFEATURE_MSBFIRST_ENABLE ((uint32_t)USART_CR2_MSBFIRST) /*!< Most significant bit sent/received first enable */
/**
* @}
- */
+ */
-/** @defgroup SMARTCARD_Flags SMARTCARD Flags
+/** @defgroup SMARTCARD_Flags SMARTCARD Flags
* Elements values convention: 0xXXXX
* - 0xXXXX : Flag mask in the ISR register
* @{
*/
-#define SMARTCARD_FLAG_REACK ((uint32_t)0x00400000)
-#define SMARTCARD_FLAG_TEACK ((uint32_t)0x00200000)
-#define SMARTCARD_FLAG_BUSY ((uint32_t)0x00010000)
-#define SMARTCARD_FLAG_EOBF ((uint32_t)0x00001000)
-#define SMARTCARD_FLAG_RTOF ((uint32_t)0x00000800)
-#define SMARTCARD_FLAG_TXE ((uint32_t)0x00000080)
-#define SMARTCARD_FLAG_TC ((uint32_t)0x00000040)
-#define SMARTCARD_FLAG_RXNE ((uint32_t)0x00000020)
-#define SMARTCARD_FLAG_ORE ((uint32_t)0x00000008)
-#define SMARTCARD_FLAG_NE ((uint32_t)0x00000004)
-#define SMARTCARD_FLAG_FE ((uint32_t)0x00000002)
-#define SMARTCARD_FLAG_PE ((uint32_t)0x00000001)
+#define SMARTCARD_FLAG_REACK USART_ISR_REACK /*!< SMARTCARD receive enable acknowledge flag */
+#define SMARTCARD_FLAG_TEACK USART_ISR_TEACK /*!< SMARTCARD transmit enable acknowledge flag */
+#define SMARTCARD_FLAG_BUSY USART_ISR_BUSY /*!< SMARTCARD busy flag */
+#define SMARTCARD_FLAG_EOBF USART_ISR_EOBF /*!< SMARTCARD end of block flag */
+#define SMARTCARD_FLAG_RTOF USART_ISR_RTOF /*!< SMARTCARD receiver timeout flag */
+#define SMARTCARD_FLAG_TXE USART_ISR_TXE /*!< SMARTCARD transmit data register empty */
+#define SMARTCARD_FLAG_TC USART_ISR_TC /*!< SMARTCARD transmission complete */
+#define SMARTCARD_FLAG_RXNE USART_ISR_RXNE /*!< SMARTCARD read data register not empty */
+#define SMARTCARD_FLAG_IDLE USART_ISR_IDLE /*!< SMARTCARD idle line detection */
+#define SMARTCARD_FLAG_ORE USART_ISR_ORE /*!< SMARTCARD overrun error */
+#define SMARTCARD_FLAG_NE USART_ISR_NE /*!< SMARTCARD noise error */
+#define SMARTCARD_FLAG_FE USART_ISR_FE /*!< SMARTCARD frame error */
+#define SMARTCARD_FLAG_PE USART_ISR_PE /*!< SMARTCARD parity error */
/**
* @}
*/
@@ -479,34 +442,67 @@
* - ZZZZ : Flag position in the ISR register(4bits)
* @{
*/
-
-#define SMARTCARD_IT_PE ((uint16_t)0x0028)
-#define SMARTCARD_IT_TXE ((uint16_t)0x0727)
-#define SMARTCARD_IT_TC ((uint16_t)0x0626)
-#define SMARTCARD_IT_RXNE ((uint16_t)0x0525)
-
-#define SMARTCARD_IT_ERR ((uint16_t)0x0060)
-#define SMARTCARD_IT_ORE ((uint16_t)0x0300)
-#define SMARTCARD_IT_NE ((uint16_t)0x0200)
-#define SMARTCARD_IT_FE ((uint16_t)0x0100)
-#define SMARTCARD_IT_EOB ((uint16_t)0x0C3B)
-#define SMARTCARD_IT_RTO ((uint16_t)0x0B3A)
+#define SMARTCARD_IT_PE ((uint16_t)0x0028) /*!< SMARTCARD parity error interruption */
+#define SMARTCARD_IT_TXE ((uint16_t)0x0727) /*!< SMARTCARD transmit data register empty interruption */
+#define SMARTCARD_IT_TC ((uint16_t)0x0626) /*!< SMARTCARD transmission complete interruption */
+#define SMARTCARD_IT_RXNE ((uint16_t)0x0525) /*!< SMARTCARD read data register not empty interruption */
+#define SMARTCARD_IT_IDLE ((uint16_t)0x0424) /*!< SMARTCARD idle line detection interruption */
+
+#define SMARTCARD_IT_ERR ((uint16_t)0x0060) /*!< SMARTCARD error interruption */
+#define SMARTCARD_IT_ORE ((uint16_t)0x0300) /*!< SMARTCARD overrun error interruption */
+#define SMARTCARD_IT_NE ((uint16_t)0x0200) /*!< SMARTCARD noise error interruption */
+#define SMARTCARD_IT_FE ((uint16_t)0x0100) /*!< SMARTCARD frame error interruption */
+
+#define SMARTCARD_IT_EOB ((uint16_t)0x0C3B) /*!< SMARTCARD end of block interruption */
+#define SMARTCARD_IT_RTO ((uint16_t)0x0B3A) /*!< SMARTCARD receiver timeout interruption */
/**
* @}
- */
-
+ */
/** @defgroup SMARTCARD_IT_CLEAR_Flags SMARTCARD Interruption Clear Flags
* @{
*/
-#define SMARTCARD_CLEAR_PEF USART_ICR_PECF /*!< Parity Error Clear Flag */
-#define SMARTCARD_CLEAR_FEF USART_ICR_FECF /*!< Framing Error Clear Flag */
-#define SMARTCARD_CLEAR_NEF USART_ICR_NCF /*!< Noise detected Clear Flag */
-#define SMARTCARD_CLEAR_OREF USART_ICR_ORECF /*!< OverRun Error Clear Flag */
-#define SMARTCARD_CLEAR_TCF USART_ICR_TCCF /*!< Transmission Complete Clear Flag */
-#define SMARTCARD_CLEAR_RTOF USART_ICR_RTOCF /*!< Receiver Time Out Clear Flag */
-#define SMARTCARD_CLEAR_EOBF USART_ICR_EOBCF /*!< End Of Block Clear Flag */
+#define SMARTCARD_CLEAR_PEF USART_ICR_PECF /*!< SMARTCARD parity error clear flag */
+#define SMARTCARD_CLEAR_FEF USART_ICR_FECF /*!< SMARTCARD framing error clear flag */
+#define SMARTCARD_CLEAR_NEF USART_ICR_NCF /*!< SMARTCARD noise detected clear flag */
+#define SMARTCARD_CLEAR_OREF USART_ICR_ORECF /*!< SMARTCARD overrun error clear flag */
+#define SMARTCARD_CLEAR_IDLEF USART_ICR_IDLECF /*!< SMARTCARD idle line detected clear flag */
+#define SMARTCARD_CLEAR_TCF USART_ICR_TCCF /*!< SMARTCARD transmission complete clear flag */
+#define SMARTCARD_CLEAR_RTOF USART_ICR_RTOCF /*!< SMARTCARD receiver time out clear flag */
+#define SMARTCARD_CLEAR_EOBF USART_ICR_EOBCF /*!< SMARTCARD end of block clear flag */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_CR3_SCARCNT_LSB_POS SMARTCARD auto retry counter LSB position in CR3 register
+ * @{
+ */
+#define SMARTCARD_CR3_SCARCNT_LSB_POS ((uint32_t) 17) /*!< SMARTCARD auto retry counter LSB position in CR3 register */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_GTPR_GT_LSB_POS SMARTCARD guard time value LSB position in GTPR register
+ * @{
+ */
+#define SMARTCARD_GTPR_GT_LSB_POS ((uint32_t) 8) /*!< SMARTCARD guard time value LSB position in GTPR register */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_RTOR_BLEN_LSB_POS SMARTCARD block length LSB position in RTOR register
+ * @{
+ */
+#define SMARTCARD_RTOR_BLEN_LSB_POS ((uint32_t) 24) /*!< SMARTCARD block length LSB position in RTOR register */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Interruption_Mask SMARTCARD interruptions flags mask
+ * @{
+ */
+#define SMARTCARD_IT_MASK ((uint16_t)0x001F) /*!< SMARTCARD interruptions flags mask */
/**
* @}
*/
@@ -516,151 +512,178 @@
*/
#define SMARTCARD_RXDATA_FLUSH_REQUEST ((uint16_t)USART_RQR_RXFRQ) /*!< Receive Data flush Request */
#define SMARTCARD_TXDATA_FLUSH_REQUEST ((uint16_t)USART_RQR_TXFRQ) /*!< Transmit data flush Request */
-#define IS_SMARTCARD_REQUEST_PARAMETER(PARAM) (((PARAM) == SMARTCARD_RXDATA_FLUSH_REQUEST) || \
- ((PARAM) == SMARTCARD_TXDATA_FLUSH_REQUEST))
/**
* @}
*/
-
-
-/** @defgroup SMARTCARD_CR3_SCARCNT_LSB_POS SMARTCARD auto retry counter LSB position in CR3 register
- * @{
- */
-#define SMARTCARD_CR3_SCARCNT_LSB_POS ((uint32_t) 17)
+
/**
* @}
*/
-
-/** @defgroup SMARTCARD_GTPR_GT_LSB_POS SMARTCARD guard time value LSB position in GTPR register
- * @{
- */
-#define SMARTCARD_GTPR_GT_LSB_POS ((uint32_t) 8)
-/**
- * @}
- */
-
-/** @defgroup SMARTCARD_RTOR_BLEN_LSB_POS SMARTCARD block length LSB position in RTOR register
- * @{
- */
-#define SMARTCARD_RTOR_BLEN_LSB_POS ((uint32_t) 24)
-/**
- * @}
- */
-
-/** @defgroup SMARTCARD_Interruption_Mask SMARTCARD interruptions flag mask
- * @{
- */
-#define SMARTCARD_IT_MASK ((uint16_t)0x001F)
-/**
- * @}
- */
-
-/**
- * @}
- */
-
-/* Exported macro ------------------------------------------------------------*/
-/** @defgroup SMARTCARD_Exported_Macros SMARTCARD Exported Macros
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup SMARTCARD_Exported_Macros SMARTCARD Exported Macros
* @{
*/
-/** @brief Reset SMARTCARD handle state
+/** @brief Reset SMARTCARD handle state.
* @param __HANDLE__: SMARTCARD handle.
* @retval None
*/
#define __HAL_SMARTCARD_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_SMARTCARD_STATE_RESET)
-/** @brief Checks whether the specified Smartcard flag is set or not.
+/** @brief Flush the Smartcard Data registers.
+ * @param __HANDLE__: specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_FLUSH_DRREGISTER(__HANDLE__) \
+ do{ \
+ SET_BIT((__HANDLE__)->Instance->RQR, SMARTCARD_RXDATA_FLUSH_REQUEST); \
+ SET_BIT((__HANDLE__)->Instance->RQR, SMARTCARD_TXDATA_FLUSH_REQUEST); \
+ } while(0)
+
+/** @brief Clear the specified SMARTCARD pending flag.
+ * @param __HANDLE__: specifies the SMARTCARD Handle.
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be any combination of the following values:
+ * @arg SMARTCARD_CLEAR_PEF: Parity error clear flag
+ * @arg SMARTCARD_CLEAR_FEF: Framing error clear flag
+ * @arg SMARTCARD_CLEAR_NEF: Noise detected clear flag
+ * @arg SMARTCARD_CLEAR_OREF: OverRun error clear flag
+ * @arg SMARTCARD_CLEAR_IDLEF: Idle line detected clear flag
+ * @arg SMARTCARD_CLEAR_TCF: Transmission complete clear flag
+ * @arg SMARTCARD_CLEAR_RTOF: Receiver timeout clear flag
+ * @arg SMARTCARD_CLEAR_EOBF: End of block clear flag
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->ICR = (__FLAG__))
+
+/** @brief Clear the SMARTCARD PE pending flag.
+ * @param __HANDLE__: specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_PEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_PEF)
+
+
+/** @brief Clear the SMARTCARD FE pending flag.
+ * @param __HANDLE__: specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_FEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_FEF)
+
+/** @brief Clear the SMARTCARD NE pending flag.
+ * @param __HANDLE__: specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_NEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_NEF)
+
+/** @brief Clear the SMARTCARD ORE pending flag.
+ * @param __HANDLE__: specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_OREFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_OREF)
+
+/** @brief Clear the SMARTCARD IDLE pending flag.
+ * @param __HANDLE__: specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_IDLEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_IDLEF)
+
+/** @brief Check whether the specified Smartcard flag is set or not.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __FLAG__: specifies the flag to check.
* This parameter can be one of the following values:
- * @arg SMARTCARD_FLAG_REACK: Receive enable ackowledge flag
- * @arg SMARTCARD_FLAG_TEACK: Transmit enable ackowledge flag
+ * @arg SMARTCARD_FLAG_REACK: Receive enable acknowledge flag
+ * @arg SMARTCARD_FLAG_TEACK: Transmit enable acknowledge flag
* @arg SMARTCARD_FLAG_BUSY: Busy flag
- * @arg SMARTCARD_FLAG_EOBF: End of block flag
- * @arg SMARTCARD_FLAG_RTOF: Receiver timeout flag
+ * @arg SMARTCARD_FLAG_EOBF: End of block flag
+ * @arg SMARTCARD_FLAG_RTOF: Receiver timeout flag
* @arg SMARTCARD_FLAG_TXE: Transmit data register empty flag
- * @arg SMARTCARD_FLAG_TC: Transmission Complete flag
+ * @arg SMARTCARD_FLAG_TC: Transmission complete flag
* @arg SMARTCARD_FLAG_RXNE: Receive data register not empty flag
- * @arg SMARTCARD_FLAG_ORE: OverRun Error flag
- * @arg SMARTCARD_FLAG_NE: Noise Error flag
- * @arg SMARTCARD_FLAG_FE: Framing Error flag
- * @arg SMARTCARD_FLAG_PE: Parity Error flag
+ * @arg SMARTCARD_FLAG_IDLE: Idle line detection flag
+ * @arg SMARTCARD_FLAG_ORE: Overrun error flag
+ * @arg SMARTCARD_FLAG_NE: Noise error flag
+ * @arg SMARTCARD_FLAG_FE: Framing error flag
+ * @arg SMARTCARD_FLAG_PE: Parity error flag
* @retval The new state of __FLAG__ (TRUE or FALSE).
*/
#define __HAL_SMARTCARD_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->ISR & (__FLAG__)) == (__FLAG__))
-/** @brief Enables the specified SmartCard interrupt.
+/** @brief Enable the specified SmartCard interrupt.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __INTERRUPT__: specifies the SMARTCARD interrupt to enable.
* This parameter can be one of the following values:
- * @arg SMARTCARD_IT_EOBF: End Of Block interrupt
- * @arg SMARTCARD_IT_RTOF: Receive TimeOut interrupt
- * @arg SMARTCARD_IT_TXE: Transmit Data Register empty interrupt
- * @arg SMARTCARD_IT_TC: Transmission complete interrupt
- * @arg SMARTCARD_IT_RXNE: Receive Data register not empty interrupt
- * @arg SMARTCARD_IT_PE: Parity Error interrupt
- * @arg SMARTCARD_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
+ * @arg SMARTCARD_IT_EOB: End of block interrupt
+ * @arg SMARTCARD_IT_RTO: Receive timeout interrupt
+ * @arg SMARTCARD_IT_TXE: Transmit data register empty interrupt
+ * @arg SMARTCARD_IT_TC: Transmission complete interrupt
+ * @arg SMARTCARD_IT_RXNE: Receive data register not empty interrupt
+ * @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
+ * @arg SMARTCARD_IT_PE: Parity error interrupt
+ * @arg SMARTCARD_IT_ERR: Error interrupt(frame error, noise error, overrun error)
* @retval None
*/
#define __HAL_SMARTCARD_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 |= (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 |= (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
((__HANDLE__)->Instance->CR3 |= (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))))
-/** @brief Disables the specified SmartCard interrupt.
+/** @brief Disable the specified SmartCard interrupt.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __INTERRUPT__: specifies the SMARTCARD interrupt to disable.
* This parameter can be one of the following values:
- * @arg SMARTCARD_IT_EOBF: End Of Block interrupt
- * @arg SMARTCARD_IT_RTOF: Receive TimeOut interrupt
- * @arg SMARTCARD_IT_TXE: Transmit Data Register empty interrupt
- * @arg SMARTCARD_IT_TC: Transmission complete interrupt
- * @arg SMARTCARD_IT_RXNE: Receive Data register not empty interrupt
- * @arg SMARTCARD_IT_PE: Parity Error interrupt
- * @arg SMARTCARD_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
+ * @arg SMARTCARD_IT_EOB: End of block interrupt
+ * @arg SMARTCARD_IT_RTO: Receive timeout interrupt
+ * @arg SMARTCARD_IT_TXE: Transmit data register empty interrupt
+ * @arg SMARTCARD_IT_TC: Transmission complete interrupt
+ * @arg SMARTCARD_IT_RXNE: Receive data register not empty interrupt
+ * @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
+ * @arg SMARTCARD_IT_PE: Parity error interrupt
+ * @arg SMARTCARD_IT_ERR: Error interrupt(frame error, noise error, overrun error)
* @retval None
*/
#define __HAL_SMARTCARD_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 &= ~ (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 &= ~ (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
((__HANDLE__)->Instance->CR3 &= ~ (1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))))
-
-/** @brief Checks whether the specified SmartCard interrupt has occurred or not.
+
+/** @brief Check whether the specified SmartCard interrupt has occurred or not.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __IT__: specifies the SMARTCARD interrupt to check.
* This parameter can be one of the following values:
- * @arg SMARTCARD_IT_EOBF: End Of Block interrupt
- * @arg SMARTCARD_IT_RTOF: Receive TimeOut interrupt
- * @arg SMARTCARD_IT_TXE: Transmit Data Register empty interrupt
- * @arg SMARTCARD_IT_TC: Transmission complete interrupt
- * @arg SMARTCARD_IT_RXNE: Receive Data register not empty interrupt
- * @arg SMARTCARD_IT_ORE: OverRun Error interrupt
- * @arg SMARTCARD_IT_NE: Noise Error interrupt
- * @arg SMARTCARD_IT_FE: Framing Error interrupt
- * @arg SMARTCARD_IT_PE: Parity Error interrupt
+ * @arg SMARTCARD_IT_EOB: End of block interrupt
+ * @arg SMARTCARD_IT_RTO: Receive timeout interrupt
+ * @arg SMARTCARD_IT_TXE: Transmit data register empty interrupt
+ * @arg SMARTCARD_IT_TC: Transmission complete interrupt
+ * @arg SMARTCARD_IT_RXNE: Receive data register not empty interrupt
+ * @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
+ * @arg SMARTCARD_IT_ORE: Overrun error interrupt
+ * @arg SMARTCARD_IT_NE: Noise error interrupt
+ * @arg SMARTCARD_IT_FE: Framing error interrupt
+ * @arg SMARTCARD_IT_PE: Parity error interrupt
* @retval The new state of __IT__ (TRUE or FALSE).
*/
-#define __HAL_SMARTCARD_GET_IT(__HANDLE__, __IT__) ((__HANDLE__)->Instance->ISR & ((uint32_t)1 << ((__IT__)>> 0x08)))
+#define __HAL_SMARTCARD_GET_IT(__HANDLE__, __IT__) ((__HANDLE__)->Instance->ISR & ((uint32_t)1 << ((__IT__)>> 0x08)))
-/** @brief Checks whether the specified SmartCard interrupt interrupt source is enabled.
+/** @brief Check whether the specified SmartCard interrupt source is enabled or not.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __IT__: specifies the SMARTCARD interrupt source to check.
* This parameter can be one of the following values:
- * @arg SMARTCARD_IT_EOBF: End Of Block interrupt
- * @arg SMARTCARD_IT_RTOF: Receive TimeOut interrupt
- * @arg SMARTCARD_IT_TXE: Transmit Data Register empty interrupt
- * @arg SMARTCARD_IT_TC: Transmission complete interrupt
- * @arg SMARTCARD_IT_RXNE: Receive Data register not empty interrupt
- * @arg SMARTCARD_IT_ORE: OverRun Error interrupt
- * @arg SMARTCARD_IT_NE: Noise Error interrupt
- * @arg SMARTCARD_IT_FE: Framing Error interrupt
- * @arg SMARTCARD_IT_PE: Parity Error interrupt
+ * @arg SMARTCARD_IT_EOB: End of block interrupt
+ * @arg SMARTCARD_IT_RTO: Receive timeout interrupt
+ * @arg SMARTCARD_IT_TXE: Transmit data register empty interrupt
+ * @arg SMARTCARD_IT_TC: Transmission complete interrupt
+ * @arg SMARTCARD_IT_RXNE: Receive data register not empty interrupt
+ * @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
+ * @arg SMARTCARD_IT_ORE: Overrun error interrupt
+ * @arg SMARTCARD_IT_NE: Noise error interrupt
+ * @arg SMARTCARD_IT_FE: Framing error interrupt
+ * @arg SMARTCARD_IT_PE: Parity error interrupt
* @retval The new state of __IT__ (TRUE or FALSE).
*/
#define __HAL_SMARTCARD_GET_IT_SOURCE(__HANDLE__, __IT__) ((((((uint8_t)(__IT__)) >> 5U) == 1)? (__HANDLE__)->Instance->CR1 : \
@@ -668,87 +691,261 @@
(__HANDLE__)->Instance->CR3)) & ((uint32_t)1 << (((uint16_t)(__IT__)) & SMARTCARD_IT_MASK)))
-/** @brief Clears the specified SMARTCARD ISR flag, in setting the proper ICR register flag.
+/** @brief Clear the specified SMARTCARD ISR flag, in setting the proper ICR register flag.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __IT_CLEAR__: specifies the interrupt clear register flag that needs to be set
* to clear the corresponding interrupt
* This parameter can be one of the following values:
- * @arg USART_CLEAR_PEF: Parity Error Clear Flag
- * @arg USART_CLEAR_FEF: Framing Error Clear Flag
- * @arg USART_CLEAR_NEF: Noise detected Clear Flag
- * @arg USART_CLEAR_OREF: OverRun Error Clear Flag
- * @arg USART_CLEAR_TCF: Transmission Complete Clear Flag
- * @arg USART_CLEAR_RTOF: Receiver Time Out Clear Flag
- * @arg USART_CLEAR_EOBF: End Of Block Clear Flag
+ * @arg SMARTCARD_CLEAR_PEF: Parity error clear flag
+ * @arg SMARTCARD_CLEAR_FEF: Framing error clear flag
+ * @arg SMARTCARD_CLEAR_NEF: Noise detected clear flag
+ * @arg SMARTCARD_CLEAR_OREF: OverRun error clear flag
+ * @arg SMARTCARD_CLEAR_IDLEF: Idle line detection clear flag
+ * @arg SMARTCARD_CLEAR_TCF: Transmission complete clear flag
+ * @arg SMARTCARD_CLEAR_RTOF: Receiver timeout clear flag
+ * @arg SMARTCARD_CLEAR_EOBF: End of block clear flag
* @retval None
*/
-#define __HAL_SMARTCARD_CLEAR_IT(__HANDLE__, __IT_CLEAR__) ((__HANDLE__)->Instance->ICR = (uint32_t)(__IT_CLEAR__))
+#define __HAL_SMARTCARD_CLEAR_IT(__HANDLE__, __IT_CLEAR__) ((__HANDLE__)->Instance->ICR = (uint32_t)(__IT_CLEAR__))
/** @brief Set a specific SMARTCARD request flag.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be USARTx where x: 1, 2 or 3 to select the USART peripheral.
* @param __REQ__: specifies the request flag to set
- * This parameter can be one of the following values:
- * @arg SMARTCARD_RXDATA_FLUSH_REQUEST: Receive Data flush Request
- * @arg SMARTCARD_TXDATA_FLUSH_REQUEST: Transmit data flush Request
+ * This parameter can be one of the following values:
+ * @arg SMARTCARD_RXDATA_FLUSH_REQUEST: Receive data flush Request
+ * @arg SMARTCARD_TXDATA_FLUSH_REQUEST: Transmit data flush Request
*
* @retval None
- */
-#define __HAL_SMARTCARD_SEND_REQ(__HANDLE__, __REQ__) ((__HANDLE__)->Instance->RQR |= (uint16_t)(__REQ__))
+ */
+#define __HAL_SMARTCARD_SEND_REQ(__HANDLE__, __REQ__) ((__HANDLE__)->Instance->RQR |= (uint16_t)(__REQ__))
-/** @brief Enable the USART associated to the SMARTCARD Handle
+/** @brief Enable the SMARTCARD one bit sample method.
+ * @param __HANDLE__: specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)
+
+/** @brief Disable the SMARTCARD one bit sample method.
+ * @param __HANDLE__: specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint32_t)~((uint32_t)USART_CR3_ONEBIT))
+
+/** @brief Enable the USART associated to the SMARTCARD Handle.
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be UARTx where x: 1, 2, 3 to select the USART peripheral
* @retval None
- */
+ */
#define __HAL_SMARTCARD_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
/** @brief Disable the USART associated to the SMARTCARD Handle
* @param __HANDLE__: specifies the SMARTCARD Handle.
* The Handle Instance can be UARTx where x: 1, 2, 3 to select the USART peripheral
* @retval None
- */
+ */
#define __HAL_SMARTCARD_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
+/**
+ * @}
+ */
+
+/* Private macros -------------------------------------------------------------*/
+/** @defgroup SMARTCARD_Private_Macros SMARTCARD Private Macros
+ * @{
+ */
+
/** @brief Check the Baud rate range. The maximum Baud Rate is derived from the
* maximum clock on F0 (i.e. 48 MHz) divided by the oversampling used
- * on the SMARTCARD (i.e. 16)
+ * on the SMARTCARD (i.e. 16).
* @param __BAUDRATE__: Baud rate set by the configuration function.
- * @retval Test result (TRUE or FALSE)
- */
+ * @retval Test result (TRUE or FALSE)
+ */
#define IS_SMARTCARD_BAUDRATE(__BAUDRATE__) ((__BAUDRATE__) < 4500001)
-/** @brief Check the block length range. The maximum SMARTCARD block length is 0xFF.
+/** @brief Check the block length range.
+ * @note The maximum SMARTCARD block length is 0xFF.
* @param __LENGTH__: block length.
- * @retval Test result (TRUE or FALSE)
+ * @retval Test result (TRUE or FALSE)
*/
#define IS_SMARTCARD_BLOCKLENGTH(__LENGTH__) ((__LENGTH__) <= 0xFF)
-/** @brief Check the receiver timeout value. The maximum SMARTCARD receiver timeout
- * value is 0xFFFFFF.
+/** @brief Check the receiver timeout value.
+ * @note The maximum SMARTCARD receiver timeout value is 0xFFFFFF.
* @param __TIMEOUTVALUE__: receiver timeout value.
- * @retval Test result (TRUE or FALSE)
+ * @retval Test result (TRUE or FALSE)
*/
#define IS_SMARTCARD_TIMEOUT_VALUE(__TIMEOUTVALUE__) ((__TIMEOUTVALUE__) <= 0xFFFFFF)
-/** @brief Check the SMARTCARD autoretry counter value. The maximum number of
- * retransmissions is 0x7.
- * @param __COUNT__: number of retransmissions
- * @retval Test result (TRUE or FALSE)
+/** @brief Check the SMARTCARD autoretry counter value.
+ * @note The maximum number of retransmissions is 0x7.
+ * @param __COUNT__: number of retransmissions.
+ * @retval Test result (TRUE or FALSE)
*/
#define IS_SMARTCARD_AUTORETRY_COUNT(__COUNT__) ((__COUNT__) <= 0x7)
/**
+ * @brief Ensure that SMARTCARD frame length is valid.
+ * @param __LENGTH__: SMARTCARD frame length.
+ * @retval SET (__LENGTH__ is valid) or RESET (__LENGTH__ is invalid)
+ */
+#define IS_SMARTCARD_WORD_LENGTH(__LENGTH__) ((__LENGTH__) == SMARTCARD_WORDLENGTH_9B)
+
+/**
+ * @brief Ensure that SMARTCARD frame number of stop bits is valid.
+ * @param __STOPBITS__: SMARTCARD frame number of stop bits.
+ * @retval SET (__STOPBITS__ is valid) or RESET (__STOPBITS__ is invalid)
+ */
+#define IS_SMARTCARD_STOPBITS(__STOPBITS__) ((__STOPBITS__) == SMARTCARD_STOPBITS_1_5)
+
+/**
+ * @brief Ensure that SMARTCARD frame parity is valid.
+ * @param __PARITY__: SMARTCARD frame parity.
+ * @retval SET (__PARITY__ is valid) or RESET (__PARITY__ is invalid)
+ */
+#define IS_SMARTCARD_PARITY(__PARITY__) (((__PARITY__) == SMARTCARD_PARITY_EVEN) || \
+ ((__PARITY__) == SMARTCARD_PARITY_ODD))
+
+/**
+ * @brief Ensure that SMARTCARD communication mode is valid.
+ * @param __MODE__: SMARTCARD communication mode.
+ * @retval SET (__MODE__ is valid) or RESET (__MODE__ is invalid)
+ */
+#define IS_SMARTCARD_MODE(__MODE__) ((((__MODE__) & (uint16_t)0xFFF3) == 0x00) && ((__MODE__) != (uint16_t)0x00))
+
+/**
+ * @brief Ensure that SMARTCARD frame polarity is valid.
+ * @param __CPOL__: SMARTCARD frame polarity.
+ * @retval SET (__CPOL__ is valid) or RESET (__CPOL__ is invalid)
+ */
+#define IS_SMARTCARD_POLARITY(__CPOL__) (((__CPOL__) == SMARTCARD_POLARITY_LOW) || ((__CPOL__) == SMARTCARD_POLARITY_HIGH))
+
+/**
+ * @brief Ensure that SMARTCARD frame phase is valid.
+ * @param __CPHA__: SMARTCARD frame phase.
+ * @retval SET (__CPHA__ is valid) or RESET (__CPHA__ is invalid)
+ */
+#define IS_SMARTCARD_PHASE(__CPHA__) (((__CPHA__) == SMARTCARD_PHASE_1EDGE) || ((__CPHA__) == SMARTCARD_PHASE_2EDGE))
+
+/**
+ * @brief Ensure that SMARTCARD frame last bit clock pulse setting is valid.
+ * @param __LASTBIT__: SMARTCARD frame last bit clock pulse setting.
+ * @retval SET (__LASTBIT__ is valid) or RESET (__LASTBIT__ is invalid)
+ */
+#define IS_SMARTCARD_LASTBIT(__LASTBIT__) (((__LASTBIT__) == SMARTCARD_LASTBIT_DISABLE) || \
+ ((__LASTBIT__) == SMARTCARD_LASTBIT_ENABLE))
+
+/**
+ * @brief Ensure that SMARTCARD frame sampling is valid.
+ * @param __ONEBIT__: SMARTCARD frame sampling.
+ * @retval SET (__ONEBIT__ is valid) or RESET (__ONEBIT__ is invalid)
+ */
+#define IS_SMARTCARD_ONE_BIT_SAMPLE(__ONEBIT__) (((__ONEBIT__) == SMARTCARD_ONE_BIT_SAMPLE_DISABLE) || \
+ ((__ONEBIT__) == SMARTCARD_ONE_BIT_SAMPLE_ENABLE))
+
+/**
+ * @brief Ensure that SMARTCARD NACK transmission setting is valid.
+ * @param __NACK__: SMARTCARD NACK transmission setting.
+ * @retval SET (__NACK__ is valid) or RESET (__NACK__ is invalid)
+ */
+#define IS_SMARTCARD_NACK(__NACK__) (((__NACK__) == SMARTCARD_NACK_ENABLE) || \
+ ((__NACK__) == SMARTCARD_NACK_DISABLE))
+
+/**
+ * @brief Ensure that SMARTCARD receiver timeout setting is valid.
+ * @param __TIMEOUT__: SMARTCARD receiver timeout setting.
+ * @retval SET (__TIMEOUT__ is valid) or RESET (__TIMEOUT__ is invalid)
+ */
+#define IS_SMARTCARD_TIMEOUT(__TIMEOUT__) (((__TIMEOUT__) == SMARTCARD_TIMEOUT_DISABLE) || \
+ ((__TIMEOUT__) == SMARTCARD_TIMEOUT_ENABLE))
+
+/**
+ * @brief Ensure that SMARTCARD advanced features initialization is valid.
+ * @param __INIT__: SMARTCARD advanced features initialization.
+ * @retval SET (__INIT__ is valid) or RESET (__INIT__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_INIT(__INIT__) ((__INIT__) <= (SMARTCARD_ADVFEATURE_NO_INIT | \
+ SMARTCARD_ADVFEATURE_TXINVERT_INIT | \
+ SMARTCARD_ADVFEATURE_RXINVERT_INIT | \
+ SMARTCARD_ADVFEATURE_DATAINVERT_INIT | \
+ SMARTCARD_ADVFEATURE_SWAP_INIT | \
+ SMARTCARD_ADVFEATURE_RXOVERRUNDISABLE_INIT | \
+ SMARTCARD_ADVFEATURE_DMADISABLEONERROR_INIT | \
+ SMARTCARD_ADVFEATURE_MSBFIRST_INIT))
+
+/**
+ * @brief Ensure that SMARTCARD frame TX inversion setting is valid.
+ * @param __TXINV__: SMARTCARD frame TX inversion setting.
+ * @retval SET (__TXINV__ is valid) or RESET (__TXINV__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_TXINV(__TXINV__) (((__TXINV__) == SMARTCARD_ADVFEATURE_TXINV_DISABLE) || \
+ ((__TXINV__) == SMARTCARD_ADVFEATURE_TXINV_ENABLE))
+
+/**
+ * @brief Ensure that SMARTCARD frame RX inversion setting is valid.
+ * @param __RXINV__: SMARTCARD frame RX inversion setting.
+ * @retval SET (__RXINV__ is valid) or RESET (__RXINV__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_RXINV(__RXINV__) (((__RXINV__) == SMARTCARD_ADVFEATURE_RXINV_DISABLE) || \
+ ((__RXINV__) == SMARTCARD_ADVFEATURE_RXINV_ENABLE))
+
+/**
+ * @brief Ensure that SMARTCARD frame data inversion setting is valid.
+ * @param __DATAINV__: SMARTCARD frame data inversion setting.
+ * @retval SET (__DATAINV__ is valid) or RESET (__DATAINV__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_DATAINV(__DATAINV__) (((__DATAINV__) == SMARTCARD_ADVFEATURE_DATAINV_DISABLE) || \
+ ((__DATAINV__) == SMARTCARD_ADVFEATURE_DATAINV_ENABLE))
+
+/**
+ * @brief Ensure that SMARTCARD frame RX/TX pins swap setting is valid.
+ * @param __SWAP__: SMARTCARD frame RX/TX pins swap setting.
+ * @retval SET (__SWAP__ is valid) or RESET (__SWAP__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_SWAP(__SWAP__) (((__SWAP__) == SMARTCARD_ADVFEATURE_SWAP_DISABLE) || \
+ ((__SWAP__) == SMARTCARD_ADVFEATURE_SWAP_ENABLE))
+
+/**
+ * @brief Ensure that SMARTCARD frame overrun setting is valid.
+ * @param __OVERRUN__: SMARTCARD frame overrun setting.
+ * @retval SET (__OVERRUN__ is valid) or RESET (__OVERRUN__ is invalid)
+ */
+#define IS_SMARTCARD_OVERRUN(__OVERRUN__) (((__OVERRUN__) == SMARTCARD_ADVFEATURE_OVERRUN_ENABLE) || \
+ ((__OVERRUN__) == SMARTCARD_ADVFEATURE_OVERRUN_DISABLE))
+
+/**
+ * @brief Ensure that SMARTCARD DMA enabling or disabling on error setting is valid.
+ * @param __DMA__: SMARTCARD DMA enabling or disabling on error setting.
+ * @retval SET (__DMA__ is valid) or RESET (__DMA__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_DMAONRXERROR(__DMA__) (((__DMA__) == SMARTCARD_ADVFEATURE_DMA_ENABLEONRXERROR) || \
+ ((__DMA__) == SMARTCARD_ADVFEATURE_DMA_DISABLEONRXERROR))
+
+/**
+ * @brief Ensure that SMARTCARD frame MSB first setting is valid.
+ * @param __MSBFIRST__: SMARTCARD frame MSB first setting.
+ * @retval SET (__MSBFIRST__ is valid) or RESET (__MSBFIRST__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_MSBFIRST(__MSBFIRST__) (((__MSBFIRST__) == SMARTCARD_ADVFEATURE_MSBFIRST_DISABLE) || \
+ ((__MSBFIRST__) == SMARTCARD_ADVFEATURE_MSBFIRST_ENABLE))
+
+/**
+ * @brief Ensure that SMARTCARD request parameter is valid.
+ * @param __PARAM__: SMARTCARD request parameter.
+ * @retval SET (__PARAM__ is valid) or RESET (__PARAM__ is invalid)
+ */
+#define IS_SMARTCARD_REQUEST_PARAMETER(__PARAM__) (((__PARAM__) == SMARTCARD_RXDATA_FLUSH_REQUEST) || \
+ ((__PARAM__) == SMARTCARD_TXDATA_FLUSH_REQUEST))
+
+/**
* @}
- */
+ */
/* Include SMARTCARD HAL Extended module */
-#include "stm32f0xx_hal_smartcard_ex.h"
+#include "stm32f0xx_hal_smartcard_ex.h"
-
/* Exported functions --------------------------------------------------------*/
-
/** @addtogroup SMARTCARD_Exported_Functions SMARTCARD Exported Functions
* @{
*/
@@ -762,9 +959,10 @@
HAL_StatusTypeDef HAL_SMARTCARD_DeInit(SMARTCARD_HandleTypeDef *hsmartcard);
void HAL_SMARTCARD_MspInit(SMARTCARD_HandleTypeDef *hsmartcard);
void HAL_SMARTCARD_MspDeInit(SMARTCARD_HandleTypeDef *hsmartcard);
+
/**
* @}
- */
+ */
/** @addtogroup SMARTCARD_Exported_Functions_Group2 IO operation functions
* @{
@@ -780,23 +978,25 @@
void HAL_SMARTCARD_TxCpltCallback(SMARTCARD_HandleTypeDef *hsmartcard);
void HAL_SMARTCARD_RxCpltCallback(SMARTCARD_HandleTypeDef *hsmartcard);
void HAL_SMARTCARD_ErrorCallback(SMARTCARD_HandleTypeDef *hsmartcard);
+
/**
* @}
- */
+ */
/** @addtogroup SMARTCARD_Exported_Functions_Group3 Peripheral State and Errors functions
* @{
- */
+ */
/* Peripheral State and Error functions ***************************************/
HAL_SMARTCARD_StateTypeDef HAL_SMARTCARD_GetState(SMARTCARD_HandleTypeDef *hsmartcard);
-uint32_t HAL_SMARTCARD_GetError(SMARTCARD_HandleTypeDef *hsmartcard);
+uint32_t HAL_SMARTCARD_GetError(SMARTCARD_HandleTypeDef *hsmartcard);
+
/**
* @}
*/
-
+
/**
* @}
- */
+ */
/**
* @}