Ricardo Benitez
/
mbed
Important changes to repositories hosted on mbed.com
Mbed hosted mercurial repositories are deprecated and are due to be permanently deleted in July 2026.
To keep a copy of this software download the repository Zip archive or clone locally using Mercurial.
It is also possible to export all your personal repositories from the account settings page.
Fork of
mbed
by 
mbed official
Diff: TARGET_NUCLEO_F411RE/stm32f4xx_hal_rcc_ex.h
- Revision:
- 110:165afa46840b
- Parent:
- 106:ba1f97679dad
--- a/TARGET_NUCLEO_F411RE/stm32f4xx_hal_rcc_ex.h Thu Oct 29 08:40:18 2015 +0000
+++ b/TARGET_NUCLEO_F411RE/stm32f4xx_hal_rcc_ex.h Wed Nov 25 13:21:40 2015 +0000
@@ -2,8 +2,8 @@
******************************************************************************
* @file stm32f4xx_hal_rcc_ex.h
* @author MCD Application Team
- * @version V1.3.2
- * @date 26-June-2015
+ * @version V1.4.1
+ * @date 09-October-2015
* @brief Header file of RCC HAL Extension module.
******************************************************************************
* @attention
@@ -68,10 +68,10 @@
This parameter can be a value of @ref RCC_PLL_Config */
uint32_t PLLSource; /*!< RCC_PLLSource: PLL entry clock source.
- This parameter must be a value of @ref RCC_PLL_Clock_Source */
+ This parameter must be a value of @ref RCC_PLL_Clock_Source */
uint32_t PLLM; /*!< PLLM: Division factor for PLL VCO input clock.
- This parameter must be a number between Min_Data = 0 and Max_Data = 63 */
+ This parameter must be a number between Min_Data = 0 and Max_Data = 63 */
uint32_t PLLN; /*!< PLLN: Multiplication factor for PLL VCO output clock.
This parameter must be a number between Min_Data = 192 and Max_Data = 432 */
@@ -81,11 +81,13 @@
uint32_t PLLQ; /*!< PLLQ: Division factor for OTG FS, SDIO and RNG clocks.
This parameter must be a number between Min_Data = 4 and Max_Data = 15 */
-#if defined(STM32F446xx)
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) || defined(STM32F469xx) ||\
+ defined(STM32F479xx)
uint32_t PLLR; /*!< PLLR: PLL division factor for I2S, SAI, SYSTEM, SPDIFRX clocks.
- This parameter is only available in STM32F446xx devices.
+ This parameter is only available in STM32F410xx/STM32F446xx/STM32F469xx and STM32F479xx
+ devices.
This parameter must be a number between Min_Data = 2 and Max_Data = 7 */
-#endif /* STM32F446xx */
+#endif /* STM32F410xx || STM32F446xx || STM32F469xx || STM32F479xx */
}RCC_PLLInitTypeDef;
#if defined(STM32F446xx)
@@ -95,7 +97,7 @@
typedef struct
{
uint32_t PLLI2SM; /*!< Specifies division factor for PLL VCO input clock.
- This parameter must be a number between Min_Data = 2 and Max_Data = 63 */
+ This parameter must be a number between Min_Data = 2 and Max_Data = 63 */
uint32_t PLLI2SN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock.
This parameter must be a number between Min_Data = 192 and Max_Data = 432 */
@@ -105,7 +107,7 @@
uint32_t PLLI2SQ; /*!< Specifies the division factor for SAI clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 15.
- This parameter will be used only when PLLI2S is selected as Clock Source SAI */
+ This parameter will be used only when PLLI2S is selected as Clock Source SAI */
uint32_t PLLI2SR; /*!< Specifies the division factor for I2S clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 7.
@@ -118,10 +120,10 @@
typedef struct
{
uint32_t PLLSAIM; /*!< Spcifies division factor for PLL VCO input clock.
- This parameter must be a number between Min_Data = 2 and Max_Data = 63 */
+ This parameter must be a number between Min_Data = 2 and Max_Data = 63 */
uint32_t PLLSAIN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock.
- This parameter must be a number between Min_Data = 192 and Max_Data = 432 */
+ This parameter must be a number between Min_Data = 192 and Max_Data = 432 */
uint32_t PLLSAIP; /*!< Specifies division factor for OTG FS, SDIO and RNG clocks.
This parameter must be a value of @ref RCCEx_PLLSAIP_Clock_Divider */
@@ -187,7 +189,32 @@
}RCC_PeriphCLKInitTypeDef;
#endif /* STM32F446xx */
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/**
+ * @brief RCC extended clocks structure definition
+ */
+typedef struct
+{
+ uint32_t PeriphClockSelection; /*!< The Extended Clock to be configured.
+ This parameter can be a value of @ref RCCEx_Periph_Clock_Selection */
+
+ uint32_t I2SClockSelection; /*!< Specifies RTC Clock Source Selection.
+ This parameter can be a value of @ref RCCEx_I2S_APB_Clock_Source */
+
+ uint32_t RTCClockSelection; /*!< Specifies RTC Clock Source Selection.
+ This parameter can be a value of @ref RCC_RTC_Clock_Source */
+
+ uint32_t Lptim1ClockSelection; /*!< Specifies LPTIM1 Clock Source Selection.
+ This parameter can be a value of @ref RCCEx_LPTIM1_Clock_Source */
+
+ uint32_t Fmpi2c1ClockSelection; /*!< Specifies FMPI2C1 Clock Source Selection.
+ This parameter can be a value of @ref RCCEx_FMPI2C1_Clock_Source */
+ uint8_t TIMPresSelection; /*!< Specifies TIM Clock Source Selection.
+ This parameter can be a value of @ref RCCEx_TIM_PRescaler_Selection */
+}RCC_PeriphCLKInitTypeDef;
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
/**
* @brief PLLI2S Clock structure definition
@@ -215,6 +242,11 @@
uint32_t PLLSAIN; /*!< Specifies the multiplication factor for PLLI2S VCO output clock.
This parameter must be a number between Min_Data = 192 and Max_Data = 432.
This parameter will be used only when PLLSAI is selected as Clock Source SAI or LTDC */
+#if defined(STM32F469xx) || defined(STM32F479xx)
+ uint32_t PLLSAIP; /*!< Specifies division factor for OTG FS and SDIO clocks.
+ This parameter is only available in STM32F469xx/STM32F479xx devices.
+ This parameter must be a value of @ref RCCEx_PLLSAIP_Clock_Divider */
+#endif /* STM32F469xx || STM32F479xx */
uint32_t PLLSAIQ; /*!< Specifies the division factor for SAI1 clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 15.
@@ -255,18 +287,24 @@
uint8_t TIMPresSelection; /*!< Specifies TIM Clock Prescalers Selection.
This parameter can be a value of @ref RCCEx_TIM_PRescaler_Selection */
-
+#if defined(STM32F469xx) || defined(STM32F479xx)
+ uint32_t Clk48ClockSelection; /*!< Specifies CK48 Clock Selection this clock used OTG FS, SDIO and RNG clocks.
+ This parameter can be a value of @ref RCCEx_CK48_Clock_Source */
+
+ uint32_t SdioClockSelection; /*!< Specifies SDIO Clock Source Selection.
+ This parameter can be a value of @ref RCCEx_SDIO_Clock_Source */
+#endif /* STM32F469xx || STM32F479xx */
}RCC_PeriphCLKInitTypeDef;
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-
-#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\
defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
/**
* @brief PLLI2S Clock structure definition
*/
typedef struct
{
-#if defined(STM32F411xE)
+#if defined(STM32F411xE)
uint32_t PLLI2SM; /*!< PLLM: Division factor for PLLI2S VCO input clock.
This parameter must be a number between Min_Data = 2 and Max_Data = 62 */
#endif /* STM32F411xE */
@@ -294,7 +332,7 @@
This parameter will be used only when PLLI2S is selected as Clock Source I2S or SAI */
uint32_t RTCClockSelection; /*!< Specifies RTC Clock Prescalers Selection.
- This parameter can be a value of @ref RCC_RTC_Clock_Source */
+ This parameter can be a value of @ref RCC_RTC_Clock_Source */
}RCC_PeriphCLKInitTypeDef;
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */
@@ -310,7 +348,17 @@
/** @defgroup RCCEx_Periph_Clock_Selection RCC Periph Clock Selection
* @{
*/
-/*------------------------------- Peripheral Clock source for STM32F446xx -----------------------------*/
+/*------------------- Peripheral Clock source for STM32F410xx ----------------*/
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001)
+#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000002)
+#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000004)
+#define RCC_PERIPHCLK_FMPI2C1 ((uint32_t)0x00000008)
+#define RCC_PERIPHCLK_LPTIM1 ((uint32_t)0x00000010)
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+/*----------------------------------------------------------------------------*/
+
+/*------------------- Peripheral Clock source for STM32F446xx ----------------*/
#if defined(STM32F446xx)
#define RCC_PERIPHCLK_I2S_APB1 ((uint32_t)0x00000001)
#define RCC_PERIPHCLK_I2S_APB2 ((uint32_t)0x00000002)
@@ -325,9 +373,23 @@
#define RCC_PERIPHCLK_SPDIFRX ((uint32_t)0x00000400)
#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000800)
#endif /* STM32F446xx */
-/*-----------------------------------------------------------------------------------------------------*/
-
-/*--------------- Peripheral Clock source for STM32F42xxx/STM32F43xxx ---------------------*/
+/*-----------------------------------------------------------------------------*/
+
+/*----------- Peripheral Clock source for STM32F469xx/STM32F479xx -------------*/
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001)
+#define RCC_PERIPHCLK_SAI_PLLI2S ((uint32_t)0x00000002)
+#define RCC_PERIPHCLK_SAI_PLLSAI ((uint32_t)0x00000004)
+#define RCC_PERIPHCLK_LTDC ((uint32_t)0x00000008)
+#define RCC_PERIPHCLK_TIM ((uint32_t)0x00000010)
+#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000020)
+#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000040)
+#define RCC_PERIPHCLK_CK48 ((uint32_t)0x00000080)
+#define RCC_PERIPHCLK_SDIO ((uint32_t)0x00000100)
+#endif /* STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*-------- Peripheral Clock source for STM32F42xxx/STM32F43xxx ---------------*/
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001)
#define RCC_PERIPHCLK_SAI_PLLI2S ((uint32_t)0x00000002)
@@ -337,29 +399,44 @@
#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000020)
#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000040)
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-/*-----------------------------------------------------------------------------------------------------*/
-
-/*------------------------ Peripheral Clock source for STM32F40xxx/STM32F41xxx ------------------------*/
+/*----------------------------------------------------------------------------*/
+
+/*-------- Peripheral Clock source for STM32F40xxx/STM32F41xxx ---------------*/
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\
defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
#define RCC_PERIPHCLK_I2S ((uint32_t)0x00000001)
#define RCC_PERIPHCLK_RTC ((uint32_t)0x00000002)
#define RCC_PERIPHCLK_PLLI2S ((uint32_t)0x00000004)
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */
-/*-----------------------------------------------------------------------------------------------------*/
+/*----------------------------------------------------------------------------*/
/**
* @}
*/
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+/** @defgroup RCCEx_I2S_Clock_Source I2S Clock Source
+ * @{
+ */
+#define RCC_I2SCLKSOURCE_PLLI2S ((uint32_t)0x00000000)
+#define RCC_I2SCLKSOURCE_EXT ((uint32_t)0x00000001)
+/**
+ * @}
+ */
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
/** @defgroup RCCEx_PLLSAI_DIVR RCC PLLSAI DIVR
* @{
*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) ||\
+ defined(STM32F469xx) || defined(STM32F479xx)
#define RCC_PLLSAIDIVR_2 ((uint32_t)0x00000000)
#define RCC_PLLSAIDIVR_4 ((uint32_t)0x00010000)
#define RCC_PLLSAIDIVR_8 ((uint32_t)0x00020000)
#define RCC_PLLSAIDIVR_16 ((uint32_t)0x00030000)
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
/**
* @}
*/
@@ -367,12 +444,12 @@
/** @defgroup RCCEx_PLLI2SP_Clock_Divider RCC PLLI2SP Clock Divider
* @{
*/
-#if defined(STM32F446xx)
+#if defined(STM32F446xx)
#define RCC_PLLI2SP_DIV2 ((uint32_t)0x00000002)
#define RCC_PLLI2SP_DIV4 ((uint32_t)0x00000004)
#define RCC_PLLI2SP_DIV6 ((uint32_t)0x00000006)
#define RCC_PLLI2SP_DIV8 ((uint32_t)0x00000008)
-#endif /* STM32F446xx */
+#endif /* STM32F446xx */
/**
* @}
*/
@@ -380,17 +457,17 @@
/** @defgroup RCCEx_PLLSAIP_Clock_Divider RCC PLLSAIP Clock Divider
* @{
*/
-#if defined(STM32F446xx)
+#if defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
#define RCC_PLLSAIP_DIV2 ((uint32_t)0x00000002)
#define RCC_PLLSAIP_DIV4 ((uint32_t)0x00000004)
#define RCC_PLLSAIP_DIV6 ((uint32_t)0x00000006)
#define RCC_PLLSAIP_DIV8 ((uint32_t)0x00000008)
-#endif /* STM32F446xx */
+#endif /* STM32F446xx || STM32F469xx || STM32F479xx */
/**
* @}
*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @defgroup RCCEx_SAI_BlockA_Clock_Source RCC SAI BlockA Clock Source
* @{
*/
@@ -410,7 +487,36 @@
/**
* @}
*/
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+/** @defgroup RCCEx_CK48_Clock_Source RCC CK48 Clock Source
+ * @{
+ */
+#define RCC_CK48CLKSOURCE_PLLQ ((uint32_t)0x00000000)
+#define RCC_CK48CLKSOURCE_PLLSAIP ((uint32_t)RCC_DCKCFGR_CK48MSEL)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_SDIO_Clock_Source RCC SDIO Clock Source
+ * @{
+ */
+#define RCC_SDIOCLKSOURCE_CK48 ((uint32_t)0x00000000)
+#define RCC_SDIOCLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR_SDIOSEL)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_DSI_Clock_Source RCC DSI Clock Source
+ * @{
+ */
+#define RCC_DSICLKSOURCE_DSIPHY ((uint32_t)0x00000000)
+#define RCC_DSICLKSOURCE_PLLR ((uint32_t)RCC_DCKCFGR_DSISEL)
+/**
+ * @}
+ */
+#endif /* STM32F469xx || STM32F479xx */
#if defined(STM32F446xx)
/** @defgroup RCCEx_SAI1_Clock_Source RCC SAI1 Clock Source
@@ -502,11 +608,42 @@
/**
* @}
*/
-
+
#endif /* STM32F446xx */
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\
- defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx)
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+
+/** @defgroup RCCEx_I2S_APB_Clock_Source RCC I2S APB Clock Source
+ * @{
+ */
+#define RCC_I2SAPBCLKSOURCE_PLLR ((uint32_t)0x00000000)
+#define RCC_I2SAPBCLKSOURCE_EXT ((uint32_t)RCC_DCKCFGR_I2SSRC_0)
+#define RCC_I2SAPBCLKSOURCE_PLLSRC ((uint32_t)RCC_DCKCFGR_I2SSRC_1)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_FMPI2C1_Clock_Source RCC FMPI2C1 Clock Source
+ * @{
+ */
+#define RCC_FMPI2C1CLKSOURCE_APB ((uint32_t)0x00000000)
+#define RCC_FMPI2C1CLKSOURCE_SYSCLK ((uint32_t)RCC_DCKCFGR2_FMPI2C1SEL_0)
+#define RCC_FMPI2C1CLKSOURCE_HSI ((uint32_t)RCC_DCKCFGR2_FMPI2C1SEL_1)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_LPTIM1_Clock_Source RCC LPTIM1 Clock Source
+ * @{
+ */
+#define RCC_LPTIM1CLKSOURCE_PCLK ((uint32_t)0x00000000)
+#define RCC_LPTIM1CLKSOURCE_HSI ((uint32_t)RCC_DCKCFGR2_LPTIM1SEL_0)
+#define RCC_LPTIM1CLKSOURCE_LSI ((uint32_t)RCC_DCKCFGR2_LPTIM1SEL_1)
+#define RCC_LPTIM1CLKSOURCE_LSE ((uint32_t)RCC_DCKCFGR2_LPTIM1SEL_0 | RCC_DCKCFGR2_LPTIM1SEL_1)
+/**
+ * @}
+ */
+
/** @defgroup RCCEx_TIM_PRescaler_Selection RCC TIM PRescaler Selection
* @{
*/
@@ -515,9 +652,24 @@
/**
* @}
*/
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx) || STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx */
-
-#if defined(STM32F411xE) || defined(STM32F446xx)
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) ||\
+ defined(STM32F469xx) || defined(STM32F479xx)
+/** @defgroup RCCEx_TIM_PRescaler_Selection RCC TIM PRescaler Selection
+ * @{
+ */
+#define RCC_TIMPRES_DESACTIVATED ((uint8_t)0x00)
+#define RCC_TIMPRES_ACTIVATED ((uint8_t)0x01)
+/**
+ * @}
+ */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F401xC || STM32F401xE ||\
+ STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) ||\
+ defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @defgroup RCCEx_LSE_Dual_Mode_Selection RCC LSE Dual Mode Selection
* @{
*/
@@ -526,7 +678,38 @@
/**
* @}
*/
-#endif /* STM32F411xE || STM32F446xx */
+#endif /* STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
+
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+/** @defgroup RCC_MCO2_Clock_Source MCO2 Clock Source
+ * @{
+ */
+#define RCC_MCO2SOURCE_SYSCLK ((uint32_t)0x00000000)
+#define RCC_MCO2SOURCE_PLLI2SCLK RCC_CFGR_MCO2_0
+#define RCC_MCO2SOURCE_HSE RCC_CFGR_MCO2_1
+#define RCC_MCO2SOURCE_PLLCLK RCC_CFGR_MCO2
+/**
+ * @}
+ */
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/** @defgroup RCC_MCO2_Clock_Source MCO2 Clock Source
+ * @{
+ */
+#define RCC_MCO2SOURCE_SYSCLK ((uint32_t)0x00000000)
+#define RCC_MCO2SOURCE_I2SCLK RCC_CFGR_MCO2_0
+#define RCC_MCO2SOURCE_HSE RCC_CFGR_MCO2_1
+#define RCC_MCO2SOURCE_PLLCLK RCC_CFGR_MCO2
+/**
+ * @}
+ */
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
/**
* @}
@@ -536,13 +719,49 @@
/** @defgroup RCCEx_Exported_Macros RCCEx Exported Macros
* @{
*/
-/*------------------------------- STM32F42xxx/STM32F43xxx ----------------------------------*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx)
-/** @brief Enables or disables the AHB1 peripheral clock.
+/*------------------- STM32F42xxx/STM32F43xxx/STM32F469xx/STM32F479xx --------*/
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB1 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
+#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ UNUSED(tmpreg); \
+ } while(0)
#define __HAL_RCC_GPIOI_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOIEN);\
@@ -627,7 +846,8 @@
tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN))
+#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN))
#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN))
#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN))
#define __HAL_RCC_GPIOI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOIEN))
@@ -640,6 +860,9 @@
#define __HAL_RCC_ETHMACPTP_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_ETHMACPTPEN))
#define __HAL_RCC_USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN))
+#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN))
+#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
/**
* @brief Enable ETHERNET clock.
@@ -657,14 +880,17 @@
__HAL_RCC_ETHMACRX_CLK_DISABLE(); \
__HAL_RCC_ETHMAC_CLK_DISABLE(); \
} while(0)
-
-/** @brief Enable or disable the AHB2 peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
-
-#define __HAL_RCC_DCMI_CLK_ENABLE() do { \
+ #define __HAL_RCC_DCMI_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_DCMIEN);\
/* Delay after an RCC peripheral clock enabling */ \
@@ -673,7 +899,7 @@
} while(0)
#define __HAL_RCC_DCMI_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_DCMIEN))
-#if defined(STM32F437xx)|| defined(STM32F439xx)
+#if defined(STM32F437xx)|| defined(STM32F439xx) || defined(STM32F479xx)
#define __HAL_RCC_CRYP_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_CRYPEN);\
@@ -691,9 +917,40 @@
#define __HAL_RCC_CRYP_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_CRYPEN))
#define __HAL_RCC_HASH_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_HASHEN))
-#endif /* STM32F437xx || STM32F439xx */
-
-/** @brief Enables or disables the AHB3 peripheral clock.
+#endif /* STM32F437xx || STM32F439xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEX_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_ENABLE();\
+ }while(0)
+
+#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() do { (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_DISABLE();\
+ }while(0)
+
+#define __HAL_RCC_RNG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_RNGEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB3 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -706,8 +963,22 @@
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_FMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FMCEN))
-
-/** @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_QSPI_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_QSPI_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_QSPIEN))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -810,7 +1081,46 @@
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_UART8EN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN))
+#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN))
+#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN))
#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN))
#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN))
#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN))
@@ -824,8 +1134,12 @@
#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN))
#define __HAL_RCC_UART7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART7EN))
#define __HAL_RCC_UART8_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_UART8EN))
-
-/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -872,22 +1186,69 @@
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN);\
UNUSED(tmpreg); \
} while(0)
-
-#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
-#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
-#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
-#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
-#define __HAL_RCC_SPI6_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI6EN))
-#define __HAL_RCC_SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN))
-
-#if defined(STM32F429xx)|| defined(STM32F439xx)
-#define __HAL_RCC_LTDC_CLK_ENABLE() (RCC->APB2ENR |= (RCC_APB2ENR_LTDCEN))
+#define __HAL_RCC_SDIO_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM10_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN))
+#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN))
+#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN))
+#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
+#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
+#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
+#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
+#define __HAL_RCC_SPI6_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI6EN))
+#define __HAL_RCC_SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN))
+
+#if defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_LTDC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_LTDCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_LTDCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
#define __HAL_RCC_LTDC_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_LTDCEN))
-#endif /* STM32F429xx || STM32F439xx */
-
-/** @brief Force or release AHB1 peripheral reset.
- */
+#endif /* STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_DSI_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_DSIEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DSIEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_DSI_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_DSIEN))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ */
+#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_GPIOI_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOIRST))
@@ -896,7 +1257,10 @@
#define __HAL_RCC_GPIOJ_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOJRST))
#define __HAL_RCC_GPIOK_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOKRST))
#define __HAL_RCC_DMA2D_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_DMA2DRST))
-
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+
+#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_GPIOI_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOIRST))
@@ -905,26 +1269,55 @@
#define __HAL_RCC_GPIOJ_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOJRST))
#define __HAL_RCC_GPIOK_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOKRST))
#define __HAL_RCC_DMA2D_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_DMA2DRST))
-
-/** @brief Force or release AHB2 peripheral reset.
- */
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST))
+#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_RNGRST))
#define __HAL_RCC_DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST))
+
+#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00)
+#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST))
+#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_RNGRST))
#define __HAL_RCC_DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST))
-#if defined(STM32F437xx)|| defined(STM32F439xx)
+#if defined(STM32F437xx)|| defined(STM32F439xx) || defined(STM32F479xx)
#define __HAL_RCC_CRYP_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_CRYPRST))
#define __HAL_RCC_HASH_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_HASHRST))
#define __HAL_RCC_CRYP_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_CRYPRST))
#define __HAL_RCC_HASH_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_HASHRST))
-#endif /* STM32F437xx || STM32F439xx */
-
-/** @brief Force or release AHB3 peripheral reset
+#endif /* STM32F437xx || STM32F439xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
*/
+#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00)
#define __HAL_RCC_FMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FMCRST))
#define __HAL_RCC_FMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FMCRST))
-
-/** @brief Force or release APB1 peripheral reset.
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_QSPI_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_QSPIRST))
+#define __HAL_RCC_QSPI_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_QSPIRST))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
*/
#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST))
@@ -939,7 +1332,17 @@
#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST))
#define __HAL_RCC_UART7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART7RST))
#define __HAL_RCC_UART8_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART8RST))
-
+#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST))
+
+#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST))
#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST))
#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST))
@@ -953,30 +1356,51 @@
#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST))
#define __HAL_RCC_UART7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART7RST))
#define __HAL_RCC_UART8_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_UART8RST))
-
-/** @brief Force or release APB2 peripheral reset.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
*/
#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST))
#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST))
#define __HAL_RCC_SPI6_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI6RST))
#define __HAL_RCC_SAI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI1RST))
-
+#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST))
+
+#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_RELEASE_RESET()(RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST))
#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST))
#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST))
#define __HAL_RCC_SPI6_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI6RST))
#define __HAL_RCC_SAI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI1RST))
-#if defined(STM32F429xx)|| defined(STM32F439xx)
+#if defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
#define __HAL_RCC_LTDC_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_LTDCRST))
#define __HAL_RCC_LTDC_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_LTDCRST))
-#endif /* STM32F429xx|| STM32F439xx */
-
-/** @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+#endif /* STM32F429xx|| STM32F439xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_DSI_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_DSIRST))
+#define __HAL_RCC_DSI_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_DSIRST))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ */
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_GPIOI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOILPEN))
@@ -991,7 +1415,13 @@
#define __HAL_RCC_GPIOK_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOKLPEN))
#define __HAL_RCC_SRAM3_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM3LPEN))
#define __HAL_RCC_DMA2D_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_DMA2DLPEN))
-
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN))
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_GPIOI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOILPEN))
@@ -1005,25 +1435,44 @@
#define __HAL_RCC_GPIOJ_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOJLPEN))
#define __HAL_RCC_GPIOK_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOKLPEN))
#define __HAL_RCC_DMA2D_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_DMA2DLPEN))
-
-/** @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
- * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN))
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN))
+
+#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_RNGLPEN))
+#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_RNGLPEN))
+
#define __HAL_RCC_DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN))
#define __HAL_RCC_DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN))
-#if defined(STM32F437xx)|| defined(STM32F439xx)
+#if defined(STM32F437xx)|| defined(STM32F439xx) || defined(STM32F479xx)
#define __HAL_RCC_CRYP_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_CRYPLPEN))
#define __HAL_RCC_HASH_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_HASHLPEN))
#define __HAL_RCC_CRYP_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_CRYPLPEN))
#define __HAL_RCC_HASH_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_HASHLPEN))
-#endif /* STM32F437xx || STM32F439xx */
-
-/** @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
+#endif /* STM32F437xx || STM32F439xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_LowPower_Enable_Disable AHB3 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1032,7 +1481,16 @@
#define __HAL_RCC_FMC_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_FMCLPEN))
#define __HAL_RCC_FMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FMCLPEN))
-/** @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_QSPI_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_QSPILPEN))
+#define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_QSPILPEN))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1051,7 +1509,17 @@
#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN))
#define __HAL_RCC_UART7_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART7LPEN))
#define __HAL_RCC_UART8_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART8LPEN))
-
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN))
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN))
#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN))
#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN))
#define __HAL_RCC_TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN))
@@ -1065,8 +1533,12 @@
#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN))
#define __HAL_RCC_UART7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART7LPEN))
#define __HAL_RCC_UART8_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART8LPEN))
-
-/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1078,7 +1550,13 @@
#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN))
#define __HAL_RCC_SPI6_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI6LPEN))
#define __HAL_RCC_SAI1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SAI1LPEN))
-
+#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE()(RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN))
+
+#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE()(RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN))
#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN))
#define __HAL_RCC_ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN))
#define __HAL_RCC_ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN))
@@ -1086,22 +1564,65 @@
#define __HAL_RCC_SPI6_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI6LPEN))
#define __HAL_RCC_SAI1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SAI1LPEN))
-#if defined(STM32F429xx)|| defined(STM32F439xx)
+#if defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
#define __HAL_RCC_LTDC_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_LTDCLPEN))
#define __HAL_RCC_LTDC_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_LTDCLPEN))
-#endif /* STM32F429xx || STM32F439xx */
-
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx|| STM32F439xx */
-/*---------------------------------------------------------------------------------------------*/
-
-/*----------------------------------- STM32F40xxx/STM32F41xxx----------------------------------*/
+#endif /* STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define __HAL_RCC_DSI_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_DSILPEN))
+#define __HAL_RCC_DSI_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_DSILPEN))
+#endif /* STM32F469xx || STM32F479xx */
+/**
+ * @}
+ */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx|| STM32F439xx || STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*----------------------------------- STM32F40xxx/STM32F41xxx-----------------*/
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx)
-/** @brief Enables or disables the AHB1 peripheral clock.
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB1 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
+#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ UNUSED(tmpreg); \
+ } while(0)
#define __HAL_RCC_GPIOI_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOIEN);\
@@ -1137,13 +1658,16 @@
tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN))
+#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN))
#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN))
#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN))
#define __HAL_RCC_GPIOI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOIEN))
#define __HAL_RCC_USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN))
-
+#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN))
+#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
#if defined(STM32F407xx)|| defined(STM32F417xx)
/**
* @brief Enable ETHERNET clock.
@@ -1195,12 +1719,33 @@
__HAL_RCC_ETHMAC_CLK_DISABLE(); \
} while(0)
#endif /* STM32F407xx || STM32F417xx */
-
-/** @brief Enable or disable the AHB2 peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
*/
+#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_ENABLE();\
+ }while(0)
+
+#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() do { (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_DISABLE();\
+ }while(0)
+
+#define __HAL_RCC_RNG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_RNGEN))
+
#if defined(STM32F407xx)|| defined(STM32F417xx)
#define __HAL_RCC_DCMI_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
@@ -1230,8 +1775,12 @@
#define __HAL_RCC_CRYP_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_CRYPEN))
#define __HAL_RCC_HASH_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_HASHEN))
#endif /* STM32F415xx || STM32F417xx */
-
-/** @brief Enables or disables the AHB3 peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB3 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1244,8 +1793,12 @@
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_FSMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FSMCEN))
-
-/** @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1327,7 +1880,46 @@
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN))
+#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN))
+#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN))
#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN))
#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN))
#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN))
@@ -1339,8 +1931,12 @@
#define __HAL_RCC_CAN1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN1EN))
#define __HAL_RCC_CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN))
#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN))
-
-/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1366,27 +1962,68 @@
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC3EN);\
UNUSED(tmpreg); \
} while(0)
-
-#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
-#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
-#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
-
-/** @brief Force or release AHB1 peripheral reset.
- */
+#define __HAL_RCC_SDIO_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM10_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN))
+#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN))
+#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN))
+#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
+#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
+#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ */
+#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_GPIOI_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOIRST))
#define __HAL_RCC_ETHMAC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_ETHMACRST))
#define __HAL_RCC_USB_OTG_HS_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_OTGHRST))
-
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+
+#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_GPIOI_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOIRST))
#define __HAL_RCC_ETHMAC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_ETHMACRST))
#define __HAL_RCC_USB_OTG_HS_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_OTGHRST))
-
-/** @brief Force or release AHB2 peripheral reset.
- */
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00)
+
#if defined(STM32F407xx)|| defined(STM32F417xx)
#define __HAL_RCC_DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST))
#define __HAL_RCC_DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST))
@@ -1398,15 +2035,32 @@
#define __HAL_RCC_CRYP_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_CRYPRST))
#define __HAL_RCC_HASH_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_HASHRST))
-
#endif /* STM32F415xx || STM32F417xx */
-
-/** @brief Force or release AHB3 peripheral reset
- */
+
+#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST))
+#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST))
+
+#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_RNGRST))
+#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_RNGRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00)
+
#define __HAL_RCC_FSMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FSMCRST))
#define __HAL_RCC_FSMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FSMCRST))
-
-/** @brief Force or release APB1 peripheral reset.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
*/
#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST))
@@ -1419,7 +2073,17 @@
#define __HAL_RCC_CAN1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN1RST))
#define __HAL_RCC_CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST))
#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST))
-
+#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST))
+
+#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST))
#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST))
#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST))
@@ -1431,18 +2095,35 @@
#define __HAL_RCC_CAN1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN1RST))
#define __HAL_RCC_CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST))
#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST))
-
-/** @brief Force or release APB2 peripheral reset.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
*/
#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST))
+#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST))
+
+#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_RELEASE_RESET()(RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST))
#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST))
-
-/** @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ */
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_GPIOI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOILPEN))
@@ -1453,7 +2134,13 @@
#define __HAL_RCC_ETHMACPTP_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_ETHMACPTPLPEN))
#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSLPEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSULPILPEN))
-
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN))
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_GPIOI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOILPEN))
@@ -1464,13 +2151,28 @@
#define __HAL_RCC_ETHMACPTP_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_ETHMACPTPLPEN))
#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSLPEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSULPILPEN))
-
-/** @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
- * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN))
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN))
+
+#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_RNGLPEN))
+#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_RNGLPEN))
+
#if defined(STM32F407xx)|| defined(STM32F417xx)
#define __HAL_RCC_DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN))
#define __HAL_RCC_DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN))
@@ -1483,8 +2185,12 @@
#define __HAL_RCC_CRYP_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_CRYPLPEN))
#define __HAL_RCC_HASH_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_HASHLPEN))
#endif /* STM32F415xx || STM32F417xx */
-
-/** @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_LowPower_Enable_Disable AHB3 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1492,8 +2198,12 @@
*/
#define __HAL_RCC_FSMC_CLK_SLEEP_ENABLE() (RCC->AHB3LPENR |= (RCC_AHB3LPENR_FSMCLPEN))
#define __HAL_RCC_FSMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FSMCLPEN))
-
-/** @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1510,7 +2220,17 @@
#define __HAL_RCC_CAN1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN1LPEN))
#define __HAL_RCC_CAN2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN2LPEN))
#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN))
-
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN))
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN))
#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN))
#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN))
#define __HAL_RCC_TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN))
@@ -1522,8 +2242,12 @@
#define __HAL_RCC_CAN1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN1LPEN))
#define __HAL_RCC_CAN2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN2LPEN))
#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN))
-
-/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1532,16 +2256,421 @@
#define __HAL_RCC_TIM8_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM8LPEN))
#define __HAL_RCC_ADC2_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC2LPEN))
#define __HAL_RCC_ADC3_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC3LPEN))
-
+#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE()(RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN))
+
+#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE()(RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN))
#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN))
#define __HAL_RCC_ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN))
#define __HAL_RCC_ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN))
+/**
+ * @}
+ */
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx */
-/*---------------------------------------------------------------------------------------------*/
-
-/*------------------------------------------ STM32F411xx --------------------------------------*/
-#if defined(STM32F411xE)
-/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+/*----------------------------------------------------------------------------*/
+
+/*------------------------- STM32F401xE/STM32F401xC --------------------------*/
+#if defined(STM32F401xC) || defined(STM32F401xE)
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN))
+#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
+#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN))
+#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_ENABLE();\
+ }while(0)
+
+#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() do { (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_DISABLE();\
+ }while(0)
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN))
+#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN))
+#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_SDIO_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM10_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN))
+#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN))
+#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB1_FORCE_RESET() (RCC->AHB1RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST))
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+
+#define __HAL_RCC_AHB1_RELEASE_RESET() (RCC->AHB1RSTR = 0x00)
+#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST))
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST))
+
+#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00)
+#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_APB1_FORCE_RESET() (RCC->APB1RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST))
+
+#define __HAL_RCC_APB1_RELEASE_RESET() (RCC->APB1RSTR = 0x00)
+#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_APB2_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST))
+
+#define __HAL_RCC_APB2_RELEASE_RESET() (RCC->APB2RSTR = 0x00)
+#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN))
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN))
+
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN))
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN))
+
+#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN))
+/**
+ * @}
+ */
+#endif /* STM32F401xC || STM32F401xE*/
+/*----------------------------------------------------------------------------*/
+
+/*-------------------------------- STM32F410xx -------------------------------*/
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ */
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_RNG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_RNGEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_RNGEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
+#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_RNGEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB1) peripheral clock.
+ */
+#define __HAL_RCC_TIM6_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM6EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_LPTIM1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_LPTIM1EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_LPTIM1EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_RTCAPB_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_RTCAPBEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_RTCAPBEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_FMPI2C1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_FMPI2C1EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_FMPI2C1EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_DAC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN))
+#define __HAL_RCC_RTCAPB_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_RTCAPBEN))
+#define __HAL_RCC_LPTIM1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_LPTIM1EN))
+#define __HAL_RCC_FMPI2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_FMPI2C1EN))
+#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
*/
#define __HAL_RCC_SPI5_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
@@ -1550,28 +2679,471 @@
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\
UNUSED(tmpreg); \
} while(0)
-#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
-
-/** @brief Force or release APB2 peripheral reset.
- */
-#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST))
-#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST))
-
-/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+#define __HAL_RCC_EXTIT_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_EXTITEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_EXTITEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
+#define __HAL_RCC_EXTIT_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_EXTITEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ */
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_RNGRST))
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_RNGRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET()
+#define __HAL_RCC_AHB2_RELEASE_RESET()
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
*/
-#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN))
-#define __HAL_RCC_SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN))
-
-#endif /* STM32F411xE */
-/*---------------------------------------------------------------------------------------------*/
-
-/*----------------------------------------- STM32F446xx ---------------------------------------*/
-#if defined(STM32F446xx)
-/** @brief Enables or disables the AHB1 peripheral clock.
+#define __HAL_RCC_AHB3_FORCE_RESET()
+#define __HAL_RCC_AHB3_RELEASE_RESET()
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
+ */
+#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST))
+#define __HAL_RCC_LPTIM1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_LPTIM1RST))
+#define __HAL_RCC_FMPI2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_FMPI2C1RST))
+#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST))
+
+#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST))
+#define __HAL_RCC_LPTIM1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_LPTIM1RST))
+#define __HAL_RCC_FMPI2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_FMPI2C1RST))
+#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
+ */
+#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST))
+#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ */
+#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_RNGLPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+
+#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_RNGLPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+ */
+#define __HAL_RCC_TIM6_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM6LPEN))
+#define __HAL_RCC_LPTIM1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_LPTIM1LPEN))
+#define __HAL_RCC_RTCAPB_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_RTCAPBLPEN))
+#define __HAL_RCC_FMPI2C1_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_FMPI2C1LPEN))
+#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN))
+
+#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN))
+#define __HAL_RCC_LPTIM1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_LPTIM1LPEN))
+#define __HAL_RCC_RTCAPB_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_RTCAPBLPEN))
+#define __HAL_RCC_FMPI2C1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_FMPI2C1LPEN))
+#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+ */
+#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN))
+#define __HAL_RCC_EXTIT_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_EXTITLPEN))
+#define __HAL_RCC_SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN))
+#define __HAL_RCC_EXTIT_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_EXTITLPEN))
+/**
+ * @}
+ */
+
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+/*----------------------------------------------------------------------------*/
+
+/*-------------------------------- STM32F411xx -------------------------------*/
+#if defined(STM32F411xE)
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ */
+#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN))
+#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN))
+#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN))
+#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEX_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
- */
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_ENABLE();\
+ }while(0)
+
+#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() do { (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_DISABLE();\
+ }while(0)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ */
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN))
+#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN))
+#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN))
+/**
+ * @}
+ */
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+ */
+#define __HAL_RCC_SPI5_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI5EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SDIO_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM10_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN))
+#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN))
+#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN))
+#define __HAL_RCC_SPI5_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI5EN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ */
+#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST))
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+
+#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST))
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST))
+
+#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00)
+#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
+ */
+#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST))
+
+#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
+ */
+#define __HAL_RCC_SPI5_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI5RST))
+#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST))
+
+#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST))
+#define __HAL_RCC_SPI5_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI5RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ */
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN))
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN))
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+ */
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN))
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+ */
+#define __HAL_RCC_SPI5_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI5LPEN))
+#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN))
+
+#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN))
+#define __HAL_RCC_SPI5_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI5LPEN))
+/**
+ * @}
+ */
+#endif /* STM32F411xE */
+/*----------------------------------------------------------------------------*/
+
+/*---------------------------------- STM32F446xx -----------------------------*/
+#if defined(STM32F446xx)
+/** @defgroup RCCEx_AHB1_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ */
+#define __HAL_RCC_BKPSRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_BKPSRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CCMDATARAMEN_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CCMDATARAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIODEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOEEN);\
+ UNUSED(tmpreg); \
+ } while(0)
#define __HAL_RCC_GPIOF_CLK_ENABLE() do { \
__IO uint32_t tmpreg; \
SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_GPIOFEN);\
@@ -1600,13 +3172,21 @@
tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_OTGHSULPIEN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_GPIOD_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIODEN))
+#define __HAL_RCC_GPIOE_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOEEN))
#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOFEN))
#define __HAL_RCC_GPIOG_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_GPIOGEN))
#define __HAL_RCC_USB_OTG_HS_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_OTGHSULPIEN))
-
-/** @brief Enable or disable the AHB2 peripheral clock.
+#define __HAL_RCC_BKPSRAM_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_BKPSRAMEN))
+#define __HAL_RCC_CCMDATARAMEN_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CCMDATARAMEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHB1ENR &= ~(RCC_AHB1ENR_CRCEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1619,8 +3199,28 @@
UNUSED(tmpreg); \
} while(0)
#define __HAL_RCC_DCMI_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_DCMIEN))
-
-/** @brief Enables or disables the AHB3 peripheral clock.
+#define __HAL_RCC_USB_OTG_FS_CLK_ENABLE() do {(RCC->AHB2ENR |= (RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_ENABLE();\
+ }while(0)
+
+#define __HAL_RCC_USB_OTG_FS_CLK_DISABLE() do { (RCC->AHB2ENR &= ~(RCC_AHB2ENR_OTGFSEN));\
+ __HAL_RCC_SYSCFG_CLK_DISABLE();\
+ }while(0)
+
+#define __HAL_RCC_RNG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_RNG_CLK_DISABLE() (RCC->AHB2ENR &= ~(RCC_AHB2ENR_RNGEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable
+ * @brief Enables or disables the AHB3 peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1642,8 +3242,12 @@
#define __HAL_RCC_FMC_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_FMCEN))
#define __HAL_RCC_QSPI_CLK_DISABLE() (RCC->AHB3ENR &= ~(RCC_AHB3ENR_QSPIEN))
-
-/** @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1746,7 +3350,46 @@
tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_DACEN);\
UNUSED(tmpreg); \
} while(0)
-
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM2EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_SPI3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM2EN))
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM4_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM4EN))
+#define __HAL_RCC_SPI3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_SPI3EN))
+#define __HAL_RCC_I2C3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C3EN))
#define __HAL_RCC_TIM6_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM6EN))
#define __HAL_RCC_TIM7_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM7EN))
#define __HAL_RCC_TIM12_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM12EN))
@@ -1761,8 +3404,12 @@
#define __HAL_RCC_CAN2_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CAN2EN))
#define __HAL_RCC_CEC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_CECEN))
#define __HAL_RCC_DAC_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_DACEN))
-
-/** @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
* @note After reset, the peripheral clock (used for registers read/write access)
* is disabled and the application software has to enable this clock before
* using it.
@@ -1802,44 +3449,101 @@
tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN);\
UNUSED(tmpreg); \
} while(0)
-
-#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
-#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
-#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
-#define __HAL_RCC_SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN))
-#define __HAL_RCC_SAI2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI2EN))
-
-/** @brief Force or release AHB1 peripheral reset.
- */
+#define __HAL_RCC_SDIO_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDIOEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI4EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM10_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM10EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SDIO_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SDIOEN))
+#define __HAL_RCC_SPI4_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI4EN))
+#define __HAL_RCC_TIM10_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM10EN))
+#define __HAL_RCC_TIM8_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM8EN))
+#define __HAL_RCC_ADC2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC2EN))
+#define __HAL_RCC_ADC3_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC3EN))
+#define __HAL_RCC_SAI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI1EN))
+#define __HAL_RCC_SAI2_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SAI2EN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_Force_Release_Reset AHB1 Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ */
+#define __HAL_RCC_GPIOD_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_USB_OTG_HS_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_OTGHRST))
-
+#define __HAL_RCC_CRC_FORCE_RESET() (RCC->AHB1RSTR |= (RCC_AHB1RSTR_CRCRST))
+
+#define __HAL_RCC_GPIOD_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIODRST))
+#define __HAL_RCC_GPIOE_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOERST))
#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOFRST))
#define __HAL_RCC_GPIOG_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_GPIOGRST))
#define __HAL_RCC_USB_OTG_HS_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_OTGHRST))
-
-/** @brief Force or release AHB2 peripheral reset.
- */
+#define __HAL_RCC_CRC_RELEASE_RESET() (RCC->AHB1RSTR &= ~(RCC_AHB1RSTR_CRCRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_Force_Release_Reset AHB2 Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() (RCC->AHB2RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_USB_OTG_FS_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_OTGFSRST))
+#define __HAL_RCC_RNG_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_RNGRST))
#define __HAL_RCC_DCMI_FORCE_RESET() (RCC->AHB2RSTR |= (RCC_AHB2RSTR_DCMIRST))
+
+#define __HAL_RCC_AHB2_RELEASE_RESET() (RCC->AHB2RSTR = 0x00)
+#define __HAL_RCC_USB_OTG_FS_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_OTGFSRST))
+#define __HAL_RCC_RNG_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_RNGRST))
#define __HAL_RCC_DCMI_RELEASE_RESET() (RCC->AHB2RSTR &= ~(RCC_AHB2RSTR_DCMIRST))
-
-/** @brief Force or release AHB3 peripheral reset
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_Force_Release_Reset AHB3 Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
*/
+#define __HAL_RCC_AHB3_FORCE_RESET() (RCC->AHB3RSTR = 0xFFFFFFFF)
+#define __HAL_RCC_AHB3_RELEASE_RESET() (RCC->AHB3RSTR = 0x00)
+
#define __HAL_RCC_FMC_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_FMCRST))
#define __HAL_RCC_QSPI_FORCE_RESET() (RCC->AHB3RSTR |= (RCC_AHB3RSTR_QSPIRST))
#define __HAL_RCC_FMC_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_FMCRST))
#define __HAL_RCC_QSPI_RELEASE_RESET() (RCC->AHB3RSTR &= ~(RCC_AHB3RSTR_QSPIRST))
-
-/** @brief Force or release APB1 peripheral reset.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_Force_Release_Reset APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
*/
#define __HAL_RCC_TIM6_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM7RST))
#define __HAL_RCC_TIM12_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM12RST))
#define __HAL_RCC_TIM13_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM13RST))
#define __HAL_RCC_TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST))
-#define __HAL_RCC_SPDIFRX_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPDIFRXRST))
+#define __HAL_RCC_SPDIFRX_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPDIFRXRST))
#define __HAL_RCC_USART3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_USART3RST))
#define __HAL_RCC_UART4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART4RST))
#define __HAL_RCC_UART5_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_UART5RST))
@@ -1848,7 +3552,17 @@
#define __HAL_RCC_CAN2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CAN2RST))
#define __HAL_RCC_CEC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_CECRST))
#define __HAL_RCC_DAC_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_DACRST))
-
+#define __HAL_RCC_TIM2_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C3RST))
+
+#define __HAL_RCC_TIM2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM2RST))
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM4_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM4RST))
+#define __HAL_RCC_SPI3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_SPI3RST))
+#define __HAL_RCC_I2C3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C3RST))
#define __HAL_RCC_TIM6_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM6RST))
#define __HAL_RCC_TIM7_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM7RST))
#define __HAL_RCC_TIM12_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM12RST))
@@ -1863,44 +3577,86 @@
#define __HAL_RCC_CAN2_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CAN2RST))
#define __HAL_RCC_CEC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_CECRST))
#define __HAL_RCC_DAC_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_DACRST))
-
-/** @brief Force or release APB2 peripheral reset.
- */
-#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST))
-#define __HAL_RCC_SAI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI1RST))
-#define __HAL_RCC_SAI2_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI2RST))
-
-#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST))
-#define __HAL_RCC_SAI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI1RST))
-#define __HAL_RCC_SAI2_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI2RST))
-
-/** @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_Force_Release_Reset APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
+ */
+#define __HAL_RCC_TIM8_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM8RST))
+#define __HAL_RCC_SAI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI1RST))
+#define __HAL_RCC_SAI2_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SAI2RST))
+#define __HAL_RCC_SDIO_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM10RST))
+
+#define __HAL_RCC_SDIO_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SDIORST))
+#define __HAL_RCC_SPI4_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI4RST))
+#define __HAL_RCC_TIM10_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM10RST))
+#define __HAL_RCC_TIM8_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM8RST))
+#define __HAL_RCC_SAI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI1RST))
+#define __HAL_RCC_SAI2_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SAI2RST))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB1_LowPower_Enable_Disable AHB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ */
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_SRAM2_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM2LPEN))
#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSLPEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_OTGHSULPILPEN))
-
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_ENABLE() (RCC->AHB1LPENR |= (RCC_AHB1LPENR_BKPSRAMLPEN))
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIODLPEN))
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOELPEN))
#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOFLPEN))
#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_GPIOGLPEN))
#define __HAL_RCC_SRAM2_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM2LPEN))
#define __HAL_RCC_USB_OTG_HS_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSLPEN))
#define __HAL_RCC_USB_OTG_HS_ULPI_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_OTGHSULPILPEN))
-/** @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_CRCLPEN))
+#define __HAL_RCC_FLITF_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_FLITFLPEN))
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_SRAM1LPEN))
+#define __HAL_RCC_BKPSRAM_CLK_SLEEP_DISABLE() (RCC->AHB1LPENR &= ~(RCC_AHB1LPENR_BKPSRAMLPEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB2_LowPower_Enable_Disable AHB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
- * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note After wake-up from SLEEP mode, the peripheral clock is enabled again.
* @note By default, all peripheral clocks are enabled during SLEEP mode.
- */
+ * @{
+ */
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_OTGFSLPEN))
+#define __HAL_RCC_USB_OTG_FS_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_OTGFSLPEN))
+
+#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_RNGLPEN))
+#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_RNGLPEN))
+
#define __HAL_RCC_DCMI_CLK_SLEEP_ENABLE() (RCC->AHB2LPENR |= (RCC_AHB2LPENR_DCMILPEN))
#define __HAL_RCC_DCMI_CLK_SLEEP_DISABLE() (RCC->AHB2LPENR &= ~(RCC_AHB2LPENR_DCMILPEN))
-
-/** @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_AHB3_LowPower_Enable_Disable AHB3 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1911,8 +3667,12 @@
#define __HAL_RCC_FMC_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_FMCLPEN))
#define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE() (RCC->AHB3LPENR &= ~(RCC_AHB3LPENR_QSPILPEN))
-
-/** @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB1_LowPower_Enable_Disable APB1 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1923,7 +3683,7 @@
#define __HAL_RCC_TIM12_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM12LPEN))
#define __HAL_RCC_TIM13_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM13LPEN))
#define __HAL_RCC_TIM14_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM14LPEN))
-#define __HAL_RCC_SPDIFRX_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPDIFRXLPEN))
+#define __HAL_RCC_SPDIFRX_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPDIFRXLPEN))
#define __HAL_RCC_USART3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_USART3LPEN))
#define __HAL_RCC_UART4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART4LPEN))
#define __HAL_RCC_UART5_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_UART5LPEN))
@@ -1932,23 +3692,37 @@
#define __HAL_RCC_CAN2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CAN2LPEN))
#define __HAL_RCC_CEC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_CECLPEN))
#define __HAL_RCC_DAC_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_DACLPEN))
-
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() (RCC->APB1LPENR |= (RCC_APB1LPENR_I2C3LPEN))
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM2LPEN))
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM3LPEN))
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM4LPEN))
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPI3LPEN))
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_I2C3LPEN))
#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM6LPEN))
#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM7LPEN))
#define __HAL_RCC_TIM12_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM12LPEN))
#define __HAL_RCC_TIM13_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM13LPEN))
#define __HAL_RCC_TIM14_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_TIM14LPEN))
-#define __HAL_RCC_SPDIFRX_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPDIFRXLPEN))
+#define __HAL_RCC_SPDIFRX_CLK_SLEEP_DISABLE()(RCC->APB1LPENR &= ~(RCC_APB1LPENR_SPDIFRXLPEN))
#define __HAL_RCC_USART3_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_USART3LPEN))
#define __HAL_RCC_UART4_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART4LPEN))
#define __HAL_RCC_UART5_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_UART5LPEN))
-#define __HAL_RCC_FMPI2C1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_FMPI2C1LPEN))
+#define __HAL_RCC_FMPI2C1_CLK_SLEEP_DISABLE()(RCC->APB1LPENR &= ~(RCC_APB1LPENR_FMPI2C1LPEN))
#define __HAL_RCC_CAN1_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN1LPEN))
#define __HAL_RCC_CAN2_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CAN2LPEN))
#define __HAL_RCC_CEC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_CECLPEN))
#define __HAL_RCC_DAC_CLK_SLEEP_DISABLE() (RCC->APB1LPENR &= ~(RCC_APB1LPENR_DACLPEN))
-
-/** @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_APB2_LowPower_Enable_Disable APB2 Peripheral Low Power Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
* @note Peripheral clock gating in SLEEP mode can be used to further reduce
* power consumption.
* @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
@@ -1959,18 +3733,27 @@
#define __HAL_RCC_ADC3_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_ADC3LPEN))
#define __HAL_RCC_SAI1_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SAI1LPEN))
#define __HAL_RCC_SAI2_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SAI2LPEN))
-
+#define __HAL_RCC_SDIO_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_ENABLE() (RCC->APB2LPENR |= (RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_ENABLE()(RCC->APB2LPENR |= (RCC_APB2LPENR_TIM10LPEN))
+
+#define __HAL_RCC_SDIO_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SDIOLPEN))
+#define __HAL_RCC_SPI4_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SPI4LPEN))
+#define __HAL_RCC_TIM10_CLK_SLEEP_DISABLE()(RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM10LPEN))
#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_TIM8LPEN))
#define __HAL_RCC_ADC2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC2LPEN))
#define __HAL_RCC_ADC3_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_ADC3LPEN))
#define __HAL_RCC_SAI1_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SAI1LPEN))
#define __HAL_RCC_SAI2_CLK_SLEEP_DISABLE() (RCC->APB2LPENR &= ~(RCC_APB2LPENR_SAI2LPEN))
+/**
+ * @}
+ */
#endif /* STM32F446xx */
-/*------------------------------------------------------------------------------------------------------------*/
-
-/*------------------------------------------------- PLL Configuration ----------------------------------------*/
-#if defined(STM32F446xx)
+/*----------------------------------------------------------------------------*/
+/*------------------------------- PLL Configuration --------------------------*/
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) ||\
+ defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Macro to configure the main PLL clock source, multiplication and division factors.
* @note This function must be used only when the main PLL is disabled.
* @param __RCC_PLLSource__: specifies the PLL entry clock source.
@@ -1992,7 +3775,7 @@
* This parameter must be a number in the range {2, 4, 6, or 8}.
*
* @param __PLLQ__: specifies the division factor for OTG FS, SDIO and RNG clocks
- * This parameter must be a number between Min_Data = 2 and Max_Data = 15.
+ * This parameter must be a number between Min_Data = 2 and Max_Data = 15.
* @note If the USB OTG FS is used in your application, you have to set the
* PLLQ parameter correctly to have 48 MHz clock for the USB. However,
* the SDIO and RNG need a frequency lower than or equal to 48 MHz to work
@@ -2000,7 +3783,7 @@
*
* @param __PLLR__: PLL division factor for I2S, SAI, SYSTEM, SPDIFRX clocks.
* This parameter must be a number between Min_Data = 2 and Max_Data = 7.
- * @note This parameter is only available in STM32F446xx devices.
+ * @note This parameter is only available in STM32F446xx/STM32F469xx/STM32F479xx devices.
*
*/
#define __HAL_RCC_PLL_CONFIG(__RCC_PLLSource__, __PLLM__, __PLLN__, __PLLP__, __PLLQ__,__PLLR__) \
@@ -2031,7 +3814,7 @@
* This parameter must be a number in the range {2, 4, 6, or 8}.
*
* @param __PLLQ__: specifies the division factor for OTG FS, SDIO and RNG clocks
- * This parameter must be a number between Min_Data = 2 and Max_Data = 15.
+ * This parameter must be a number between Min_Data = 2 and Max_Data = 15.
* @note If the USB OTG FS is used in your application, you have to set the
* PLLQ parameter correctly to have 48 MHz clock for the USB. However,
* the SDIO and RNG need a frequency lower than or equal to 48 MHz to work
@@ -2043,10 +3826,23 @@
((__PLLN__) << POSITION_VAL(RCC_PLLCFGR_PLLN)) | \
((((__PLLP__) >> 1) -1) << POSITION_VAL(RCC_PLLCFGR_PLLP)) | \
((__PLLQ__) << POSITION_VAL(RCC_PLLCFGR_PLLQ))))
- #endif /* STM32F446xx */
-/*-------------------------------------------------------------------------------------------------------*/
-
-/*------------------------------------------- PLLI2S Configuration --------------------------------------*/
+ #endif /* STM32F410xx || STM32F446xx || STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*----------------------------PLLI2S Configuration ---------------------------*/
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+
+/** @brief Macros to enable or disable the PLLI2S.
+ * @note The PLLI2S is disabled by hardware when entering STOP and STANDBY modes.
+ */
+#define __HAL_RCC_PLLI2S_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLI2SON_BB = ENABLE)
+#define __HAL_RCC_PLLI2S_DISABLE() (*(__IO uint32_t *) RCC_CR_PLLI2SON_BB = DISABLE)
+
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
#if defined(STM32F446xx)
/** @brief Macro to configure the PLLI2S clock multiplication and division factors .
* @note This macro must be used only when the PLLI2S is disabled.
@@ -2057,8 +3853,7 @@
* @note You have to set the PLLI2SM parameter correctly to ensure that the VCO input
* frequency ranges from 1 to 2 MHz. It is recommended to select a frequency
* of 1 MHz to limit PLLI2S jitter.
- * @note The PLLI2SM parameter is only used with STM32F411xE and STM32F446xx Devices
- *
+ *
* @param __PLLI2SN__: specifies the multiplication factor for PLLI2S VCO output clock
* This parameter must be a number between Min_Data = 192 and Max_Data = 432.
* @note You have to set the PLLI2SN parameter correctly to ensure that the VCO
@@ -2075,15 +3870,13 @@
*
* @param __PLLI2SQ__: specifies the division factor for SAI clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 15.
- * @note the PLLI2SQ parameter is only available with STM32F427/437/429x/439xx Devices
- *
- */
-#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SM__, __PLLI2SN__, __PLLI2SP__, __PLLI2SQ__, __PLLI2SR__) \
- (RCC->PLLI2SCFGR = ((__PLLI2SM__) |\
- ((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\
- ((((__PLLI2SP__) >> 1) -1) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)) |\
- ((__PLLI2SQ__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)) |\
- ((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR))))
+ */
+#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SM__, __PLLI2SN__, __PLLI2SP__, __PLLI2SQ__, __PLLI2SR__) \
+ (RCC->PLLI2SCFGR = ((__PLLI2SM__) |\
+ ((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\
+ ((((__PLLI2SP__) >> 1) -1) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SP)) |\
+ ((__PLLI2SQ__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SQ)) |\
+ ((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR))))
#else
/** @brief Macro to configure the PLLI2S clock multiplication and division factors .
* @note This macro must be used only when the PLLI2S is disabled.
@@ -2093,19 +3886,19 @@
* This parameter must be a number between Min_Data = 192 and Max_Data = 432.
* @note You have to set the PLLI2SN parameter correctly to ensure that the VCO
* output frequency is between Min_Data = 192 and Max_Data = 432 MHz.
+ *
* @param __PLLI2SR__: specifies the division factor for I2S clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 7.
* @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz
* on the I2S clock frequency.
- *
- */
-#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SN__, __PLLI2SR__) \
- (RCC->PLLI2SCFGR = (((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) | \
+ *
+ */
+#define __HAL_RCC_PLLI2S_CONFIG(__PLLI2SN__, __PLLI2SR__) \
+ (RCC->PLLI2SCFGR = (((__PLLI2SN__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SN)) |\
((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR))))
#endif /* STM32F446xx */
#if defined(STM32F411xE)
-
/** @brief Macro to configure the PLLI2S clock multiplication and division factors .
* @note This macro must be used only when the PLLI2S is disabled.
* @note This macro must be used only when the PLLI2S is disabled.
@@ -2113,7 +3906,7 @@
* HAL_RCC_ClockConfig() API).
* @param __PLLI2SM__: specifies the division factor for PLLI2S VCO input clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 63.
- * @note The PLLI2SM parameter is only used with STM32F411xE Devices
+ * @note The PLLI2SM parameter is only used with STM32F411xE/STM32F410xx Devices
* @note You have to set the PLLI2SM parameter correctly to ensure that the VCO input
* frequency ranges from 1 to 2 MHz. It is recommended to select a frequency
* of 2 MHz to limit PLLI2S jitter.
@@ -2131,7 +3924,7 @@
((__PLLI2SR__) << POSITION_VAL(RCC_PLLI2SCFGR_PLLI2SR))))
#endif /* STM32F411xE */
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Macro used by the SAI HAL driver to configure the PLLI2S clock multiplication and division factors.
* @note This macro must be used only when the PLLI2S is disabled.
* @note PLLI2S clock source is common with the main PLL (configured in
@@ -2142,8 +3935,8 @@
* output frequency is between Min_Data = 192 and Max_Data = 432 MHz.
* @param __PLLI2SQ__: specifies the division factor for SAI1 clock.
* This parameter must be a number between Min_Data = 2 and Max_Data = 15.
- * @note the PLLI2SQ parameter is only available with STM32F427xx/437xx/429xx/439xx Devices
- * and can be configured using the __HAL_RCC_PLLI2S_PLLSAICLK_CONFIG() macro
+ * @note the PLLI2SQ parameter is only available with STM32F427xx/437xx/429xx/439xx/469xx/479xx
+ * Devices and can be configured using the __HAL_RCC_PLLI2S_PLLSAICLK_CONFIG() macro
* @param __PLLI2SR__: specifies the division factor for I2S clock
* This parameter must be a number between Min_Data = 2 and Max_Data = 7.
* @note You have to set the PLLI2SR parameter correctly to not exceed 192 MHz
@@ -2152,13 +3945,13 @@
#define __HAL_RCC_PLLI2S_SAICLK_CONFIG(__PLLI2SN__, __PLLI2SQ__, __PLLI2SR__) (RCC->PLLI2SCFGR = ((__PLLI2SN__) << 6) |\
((__PLLI2SQ__) << 24) |\
((__PLLI2SR__) << 28))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-/*----------------------------------------------------------------------------------------------------------------*/
-
-/*--------------------------------------------------- PLLSAI Configuration ---------------------------------------*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx)
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*------------------------------ PLLSAI Configuration ------------------------*/
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Macros to Enable or Disable the PLLISAI.
- * @note The PLLSAI is only available with STM32F429x/439x Devices.
+ * @note The PLLSAI is only available with STM32F429x/439x Devices.
* @note The PLLSAI is disabled by hardware when entering STOP and STANDBY modes.
*/
#define __HAL_RCC_PLLSAI_ENABLE() (*(__IO uint32_t *) RCC_CR_PLLSAION_BB = ENABLE)
@@ -2196,6 +3989,30 @@
((((__PLLSAIP__) >> 1) -1) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)) | \
((__PLLSAIQ__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ))))
#endif /* STM32F446xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+/** @brief Macro to configure the PLLSAI clock multiplication and division factors.
+ *
+ * @param __PLLSAIN__: specifies the multiplication factor for PLLSAI VCO output clock.
+ * This parameter must be a number between Min_Data = 192 and Max_Data = 432.
+ * @note You have to set the PLLSAIN parameter correctly to ensure that the VCO
+ * output frequency is between Min_Data = 192 and Max_Data = 432 MHz.
+ *
+ * @param __PLLSAIP__: specifies division factor for SDIO and CLK48 clocks.
+ * This parameter must be a number in the range {2, 4, 6, or 8}.
+ *
+ * @param __PLLSAIQ__: specifies the division factor for SAI clock
+ * This parameter must be a number between Min_Data = 2 and Max_Data = 15.
+ *
+ * @param __PLLSAIR__: specifies the division factor for LTDC clock
+ * This parameter must be a number between Min_Data = 2 and Max_Data = 7.
+ */
+#define __HAL_RCC_PLLSAI_CONFIG(__PLLSAIN__, __PLLSAIP__, __PLLSAIQ__, __PLLSAIR__) \
+ (RCC->PLLSAICFGR = (((__PLLSAIN__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIN)) |\
+ ((((__PLLSAIP__) >> 1) -1) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIP)) |\
+ ((__PLLSAIQ__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIQ)) |\
+ ((__PLLSAIR__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR))))
+#endif /* STM32F469xx || STM32F479xx */
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
/** @brief Macro to configure the PLLSAI clock multiplication and division factors.
@@ -2218,14 +4035,15 @@
((__PLLSAIR__) << POSITION_VAL(RCC_PLLSAICFGR_PLLSAIR))))
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx */
-/*----------------------------------------------------------------------------------------------------------------------*/
-
-/*----------------------------------------- PLLSAI/PLLI2S Dividers Configuration ---------------------------------------*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx)
-/** @brief Macro to configure the SAI clock Divider coming from PLLI2S.
- * @note This function must be called before enabling the PLLI2S.
- * @param __PLLI2SDivQ__: specifies the PLLI2S division factor for SAI1 clock .
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*------------------- PLLSAI/PLLI2S Dividers Configuration -------------------*/
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) ||\
+ defined(STM32F469xx) || defined(STM32F479xx)
+/** @brief Macro to configure the SAI clock Divider coming from PLLI2S.
+ * @note This function must be called before enabling the PLLI2S.
+ * @param __PLLI2SDivQ__: specifies the PLLI2S division factor for SAI1 clock.
* This parameter must be a number between 1 and 32.
* SAI1 clock frequency = f(PLLI2SQ) / __PLLI2SDivQ__
*/
@@ -2238,25 +4056,26 @@
* SAI1 clock frequency = f(PLLSAIQ) / __PLLSAIDivQ__
*/
#define __HAL_RCC_PLLSAI_PLLSAICLKDIVQ_CONFIG(__PLLSAIDivQ__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_PLLSAIDIVQ, ((__PLLSAIDivQ__)-1)<<8))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Macro to configure the LTDC clock Divider coming from PLLSAI.
*
- * @note The LTDC peripheral is only available with STM32F427/437/429/439xx Devices.
+ * @note The LTDC peripheral is only available with STM32F427/437/429/439/469/479xx Devices.
* @note This function must be called before enabling the PLLSAI.
* @param __PLLSAIDivR__: specifies the PLLSAI division factor for LTDC clock .
* This parameter must be a number between Min_Data = 2 and Max_Data = 16.
* LTDC clock frequency = f(PLLSAIR) / __PLLSAIDivR__
- */
+ */
#define __HAL_RCC_PLLSAI_PLLSAICLKDIVR_CONFIG(__PLLSAIDivR__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_PLLSAIDIVR, (__PLLSAIDivR__)))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-/*-----------------------------------------------------------------------------------------------------------------------------------*/
-
-/*-------------------------------------------------- Peripheral Clock selection -----------------------------------------------------*/
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
+/*----------------------------------------------------------------------------*/
+
+/*------------------------- Peripheral Clock selection -----------------------*/
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) ||\
defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
- defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F469xx) ||\
+ defined(STM32F479xx)
/** @brief Macro to configure the I2S clock source (I2SCLK).
* @note This function must be called before enabling the I2S APB clock.
* @param __SOURCE__: specifies the I2S clock source.
@@ -2266,12 +4085,12 @@
* used as I2S clock source.
*/
#define __HAL_RCC_I2S_CONFIG(__SOURCE__) (*(__IO uint32_t *) RCC_CFGR_I2SSRC_BB = (__SOURCE__))
-#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx */
+#endif /* STM32F40xxx || STM32F41xxx || STM32F42xxx || STM32F43xxx || STM32F469xx || STM32F479xx */
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Macro to configure SAI1BlockA clock source selection.
- * @note The SAI peripheral is only available with STM32F427/437/429/439xx Devices.
+ * @note The SAI peripheral is only available with STM32F427/437/429/439/469/479xx Devices.
* @note This function must be called before enabling PLLSAI, PLLI2S and
* the SAI clock.
* @param __SOURCE__: specifies the SAI Block A clock source.
@@ -2286,7 +4105,7 @@
#define __HAL_RCC_SAI_BLOCKACLKSOURCE_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SAI1ASRC, (__SOURCE__)))
/** @brief Macro to configure SAI1BlockB clock source selection.
- * @note The SAI peripheral is only available with STM32F427/437/429/439xx Devices.
+ * @note The SAI peripheral is only available with STM32F427/437/429/439/469/479xx Devices.
* @note This function must be called before enabling PLLSAI, PLLI2S and
* the SAI clock.
* @param __SOURCE__: specifies the SAI Block B clock source.
@@ -2299,11 +4118,11 @@
* used as SAI1 Block B clock.
*/
#define __HAL_RCC_SAI_BLOCKBCLKSOURCE_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SAI1BSRC, (__SOURCE__)))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F469xx || STM32F479xx */
#if defined(STM32F446xx)
/** @brief Macro to configure SAI1 clock source selection.
- * @note This configuration is only available with STM32F446xx Devices.
+ * @note This configuration is only available with STM32F446xx Devices.
* @note This function must be called before enabling PLL, PLLSAI, PLLI2S and
* the SAI clock.
* @param __SOURCE__: specifies the SAI1 clock source.
@@ -2349,7 +4168,6 @@
#define __HAL_RCC_GET_SAI2_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_SAI2SRC))
/** @brief Macro to configure I2S APB1 clock source selection.
- * @note This configuration is only available with STM32F446xx Devices.
* @note This function must be called before enabling PLL, PLLI2S and the I2S clock.
* @param __SOURCE__: specifies the I2S APB1 clock source.
* This parameter can be one of the following values:
@@ -2361,7 +4179,6 @@
#define __HAL_RCC_I2S_APB1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2S1SRC, (__SOURCE__)))
/** @brief Macro to Get I2S APB1 clock source selection.
- * @note This configuration is only available with STM32F446xx Devices.
* @retval The clock source can be one of the following values:
* @arg RCC_I2SAPB1CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR used as I2S clock.
* @arg RCC_I2SAPB1CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin used as SAI1 clock.
@@ -2371,7 +4188,6 @@
#define __HAL_RCC_GET_I2S_APB1_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_I2S1SRC))
/** @brief Macro to configure I2S APB2 clock source selection.
- * @note This configuration is only available with STM32F446xx Devices.
* @note This function must be called before enabling PLL, PLLI2S and the I2S clock.
* @param __SOURCE__: specifies the SAI Block A clock source.
* This parameter can be one of the following values:
@@ -2383,7 +4199,6 @@
#define __HAL_RCC_I2S_APB2_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2S2SRC, (__SOURCE__)))
/** @brief Macro to Get I2S APB2 clock source selection.
- * @note This configuration is only available with STM32F446xx Devices.
* @retval The clock source can be one of the following values:
* @arg RCC_I2SAPB2CLKSOURCE_PLLI2S: PLLI2S VCO output clock divided by PLLI2SR used as I2S clock.
* @arg RCC_I2SAPB2CLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin used as SAI1 clock.
@@ -2406,21 +4221,21 @@
* @arg RCC_CECCLKSOURCE_LSE: LSE selected as CEC clock
*/
#define __HAL_RCC_GET_CEC_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_CECSEL))
-
+
/** @brief Macro to configure the FMPI2C1 clock.
* @param __SOURCE__: specifies the FMPI2C1 clock source.
* This parameter can be one of the following values:
- * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as CEC clock
- * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as CEC clock
- * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as CEC clock
+ * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock
*/
#define __HAL_RCC_FMPI2C1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL, (uint32_t)(__SOURCE__)))
/** @brief Macro to Get the FMPI2C1 clock.
* @retval The clock source can be one of the following values:
- * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as CEC clock
- * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as CEC clock
- * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as CEC clock
+ * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock
*/
#define __HAL_RCC_GET_FMPI2C1_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL))
@@ -2469,10 +4284,115 @@
*/
#define __HAL_RCC_GET_SPDIFRX_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_SPDIFRXSEL))
#endif /* STM32F446xx */
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\
- defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx)
-
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+
+/** @brief Macro to configure the CLK48 clock.
+ * @param __SOURCE__: specifies the CK48 clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_CK48CLKSOURCE_PLLQ: PLL VCO Output divided by PLLQ used as CK48 clock.
+ * @arg RCC_CK48CLKSOURCE_PLLSAIP: PLLSAI VCO Output divided by PLLSAIP used as CK48 clock.
+ */
+#define __HAL_RCC_CLK48_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_CK48MSEL, (uint32_t)(__SOURCE__)))
+
+/** @brief Macro to Get the CLK48 clock.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_CK48CLKSOURCE_PLLQ: PLL VCO Output divided by PLLQ used as CK48 clock.
+ * @arg RCC_CK48CLKSOURCE_PLLSAIP: PLLSAI VCO Output divided by PLLSAIP used as CK48 clock.
+ */
+#define __HAL_RCC_GET_CLK48_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_CK48MSEL))
+
+/** @brief Macro to configure the SDIO clock.
+ * @param __SOURCE__: specifies the SDIO clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_SDIOCLKSOURCE_CK48: CK48 output used as SDIO clock.
+ * @arg RCC_SDIOCLKSOURCE_SYSCLK: System clock output used as SDIO clock.
+ */
+#define __HAL_RCC_SDIO_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_SDIOSEL, (uint32_t)(__SOURCE__)))
+
+/** @brief Macro to Get the SDIO clock.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_SDIOCLKSOURCE_CK48: CK48 output used as SDIO clock.
+ * @arg RCC_SDIOCLKSOURCE_SYSCLK: System clock output used as SDIO clock.
+ */
+#define __HAL_RCC_GET_SDIO_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_SDIOSEL))
+
+/** @brief Macro to configure the DSI clock.
+ * @param __SOURCE__: specifies the DSI clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_DSICLKSOURCE_PLLR: PLLR output used as DSI clock.
+ * @arg RCC_DSICLKSOURCE_DSIPHY: DSI-PHY output used as DSI clock.
+ */
+#define __HAL_RCC_DSI_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_DSISEL, (uint32_t)(__SOURCE__)))
+
+/** @brief Macro to Get the DSI clock.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_DSICLKSOURCE_PLLR: PLLR output used as DSI clock.
+ * @arg RCC_DSICLKSOURCE_DSIPHY: DSI-PHY output used as DSI clock.
+ */
+#define __HAL_RCC_GET_DSI_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_DSISEL))
+
+#endif /* STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/** @brief Macro to configure I2S clock source selection.
+ * @param __SOURCE__: specifies the I2S clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_I2SAPBCLKSOURCE_PLLR: PLL VCO output clock divided by PLLR.
+ * @arg RCC_I2SAPBCLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin.
+ * @arg RCC_I2SAPBCLKSOURCE_PLLSRC: HSI/HSE depends on PLLSRC.
+ */
+#define __HAL_RCC_I2S_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR, RCC_DCKCFGR_I2SSRC, (__SOURCE__)))
+
+/** @brief Macro to Get I2S clock source selection.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_I2SAPBCLKSOURCE_PLLR: PLL VCO output clock divided by PLLR.
+ * @arg RCC_I2SAPBCLKSOURCE_EXT: External clock mapped on the I2S_CKIN pin.
+ * @arg RCC_I2SAPBCLKSOURCE_PLLSRC: HSI/HSE depends on PLLSRC.
+ */
+#define __HAL_RCC_GET_I2S_SOURCE() (READ_BIT(RCC->DCKCFGR, RCC_DCKCFGR_I2SSRC))
+
+/** @brief Macro to configure the FMPI2C1 clock.
+ * @param __SOURCE__: specifies the FMPI2C1 clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock
+ */
+#define __HAL_RCC_FMPI2C1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL, (uint32_t)(__SOURCE__)))
+
+/** @brief Macro to Get the FMPI2C1 clock.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_FMPI2C1CLKSOURCE_APB: APB selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_SYSCLK: SYS clock selected as FMPI2C1 clock
+ * @arg RCC_FMPI2C1CLKSOURCE_HSI: HSI selected as FMPI2C1 clock
+ */
+#define __HAL_RCC_GET_FMPI2C1_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_FMPI2C1SEL))
+
+/** @brief Macro to configure the LPTIM1 clock.
+ * @param __SOURCE__: specifies the LPTIM1 clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_LPTIM1CLKSOURCE_PCLK: APB selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_HSI: HSI clock selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_LSI: LSI selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_LSE: LSE selected as LPTIM1 clock
+ */
+#define __HAL_RCC_LPTIM1_CONFIG(__SOURCE__) (MODIFY_REG(RCC->DCKCFGR2, RCC_DCKCFGR2_LPTIM1SEL, (uint32_t)(__SOURCE__)))
+
+/** @brief Macro to Get the LPTIM1 clock.
+ * @retval The clock source can be one of the following values:
+ * @arg RCC_LPTIM1CLKSOURCE_PCLK: APB selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_HSI: HSI clock selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_LSI: LSI selected as LPTIM1 clock
+ * @arg RCC_LPTIM1CLKSOURCE_LSE: LSE selected as LPTIM1 clock
+ */
+#define __HAL_RCC_GET_LPTIM1_SOURCE() (READ_BIT(RCC->DCKCFGR2, RCC_DCKCFGR2_LPTIM1SEL))
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F410Tx) || defined(STM32F410Cx) ||\
+ defined(STM32F410Rx) || defined(STM32F411xE) || defined(STM32F446xx) || defined(STM32F469xx) ||\
+ defined(STM32F479xx)
/** @brief Macro to configure the Timers clocks prescalers
* @note This feature is only available with STM32F429x/439x Devices.
* @param __PRESC__ : specifies the Timers clocks prescalers selection
@@ -2488,11 +4408,12 @@
*/
#define __HAL_RCC_TIMCLKPRESCALER(__PRESC__) (*(__IO uint32_t *) RCC_DCKCFGR_TIMPRE_BB = (__PRESC__))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx) || STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx */
-
-/*-------------------------------------------------------------------------------------------------------------------*/
-
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx)
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx) || STM32F401xC || STM32F401xE || STM32F410xx || STM32F411xE ||\
+ STM32F446xx || STM32F469xx || STM32F479xx */
+
+/*----------------------------------------------------------------------------*/
+
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
/** @brief Enable PLLSAI_RDY interrupt.
*/
#define __HAL_RCC_PLLSAI_ENABLE_IT() (RCC->CIR |= (RCC_CIR_PLLSAIRDYIE))
@@ -2515,7 +4436,27 @@
*/
#define __HAL_RCC_PLLSAI_GET_FLAG() ((RCC->CR & (RCC_CR_PLLSAIRDY)) == (RCC_CR_PLLSAIRDY))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/** @defgroup RCCEx_MCO1_Enable MCO1 Enable
+ * @brief Macros to enable or disable the RCC MCO1 feature.
+ */
+#define __HAL_RCC_MCO1_ENABLE() (*(__IO uint32_t *) RCC_CFGR_MCO1EN_BB = ENABLE)
+#define __HAL_RCC_MCO1_DISABLE() (*(__IO uint32_t *) RCC_CFGR_MCO1EN_BB = DISABLE)
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_MCO2_Enable MCO2 Enable
+ * @brief Macros to enable or disable the RCC MCO2 feature.
+ */
+#define __HAL_RCC_MCO2_ENABLE() (*(__IO uint32_t *) RCC_CFGR_MCO2EN_BB = ENABLE)
+#define __HAL_RCC_MCO2_DISABLE() (*(__IO uint32_t *) RCC_CFGR_MCO2EN_BB = DISABLE)
+/**
+ * @}
+ */
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
/**
* @}
@@ -2536,9 +4477,10 @@
uint32_t HAL_RCCEx_GetPeriphCLKFreq(uint32_t PeriphClk);
#endif /* STM32F446xx */
-#if defined(STM32F411xE) || defined(STM32F446xx)
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F411xE) ||\
+ defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
void HAL_RCCEx_SelectLSEMode(uint8_t Mode);
-#endif /* STM32F411xE || STM32F446xx */
+#endif /* STM32F410xx || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
/**
* @}
*/
@@ -2558,20 +4500,60 @@
* @{
*/
/* --- CR Register ---*/
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F446xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
+ defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
/* Alias word address of PLLSAION bit */
#define RCC_PLLSAION_BIT_NUMBER 0x1C
#define RCC_CR_PLLSAION_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32) + (RCC_PLLSAION_BIT_NUMBER * 4))
+#define PLLSAI_TIMEOUT_VALUE ((uint32_t)100) /* Timeout value fixed to 100 ms */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+/* Alias word address of PLLI2SON bit */
+#define RCC_PLLI2SON_BIT_NUMBER 0x1A
+#define RCC_CR_PLLI2SON_BB (PERIPH_BB_BASE + (RCC_CR_OFFSET * 32) + (RCC_PLLI2SON_BIT_NUMBER * 4))
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
/* --- DCKCFGR Register ---*/
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) ||\
+ defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx) || defined(STM32F446xx) ||\
+ defined(STM32F469xx) || defined(STM32F479xx)
/* Alias word address of TIMPRE bit */
#define RCC_DCKCFGR_OFFSET (RCC_OFFSET + 0x8C)
#define RCC_TIMPRE_BIT_NUMBER 0x18
#define RCC_DCKCFGR_TIMPRE_BB (PERIPH_BB_BASE + (RCC_DCKCFGR_OFFSET * 32) + (RCC_TIMPRE_BIT_NUMBER * 4))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx */
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F410xx || STM32F446xx || STM32F469xx || STM32F479xx */
+
+/* --- CFGR Register ---*/
+#define RCC_CFGR_OFFSET (RCC_OFFSET + 0x08)
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+/* Alias word address of I2SSRC bit */
+#define RCC_I2SSRC_BIT_NUMBER 0x17
+#define RCC_CFGR_I2SSRC_BB (PERIPH_BB_BASE + (RCC_CFGR_OFFSET * 32) + (RCC_I2SSRC_BIT_NUMBER * 4))
+
+#define PLLI2S_TIMEOUT_VALUE ((uint32_t)100) /* Timeout value fixed to 100 ms */
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+/* Alias word address of MCO1EN bit */
+#define RCC_MCO1EN_BIT_NUMBER 0x8
+#define RCC_CFGR_MCO1EN_BB (PERIPH_BB_BASE + (RCC_CFGR_OFFSET * 32) + (RCC_MCO1EN_BIT_NUMBER * 4))
+
+/* Alias word address of MCO2EN bit */
+#define RCC_MCO2EN_BIT_NUMBER 0x9
+#define RCC_CFGR_MCO2EN_BB (PERIPH_BB_BASE + (RCC_CFGR_OFFSET * 32) + (RCC_MCO2EN_BIT_NUMBER * 4))
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
#define PLL_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
-
/**
* @}
*/
@@ -2589,23 +4571,32 @@
*/
#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx)
-#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x0000002F))
+#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x0000007F))
#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx)|| defined(STM32F417xx) ||\
defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
-#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x00000003))
+#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x00000007))
#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F401xC || STM32F401xE || STM32F411xE */
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x0000001F))
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
+
#if defined(STM32F446xx)
-#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x000007FF))
+#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x00000FFF))
#endif /* STM32F446xx */
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define IS_RCC_PERIPHCLOCK(SELECTION) ((1 <= (SELECTION)) && ((SELECTION) <= 0x000001FF))
+#endif /* STM32F469xx || STM32F479xx */
+
#define IS_RCC_PLLI2SN_VALUE(VALUE) ((192 <= (VALUE)) && ((VALUE) <= 432))
#define IS_RCC_PLLI2SR_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 7))
-#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) || defined(STM32F446xx)
+#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx)|| defined(STM32F439xx) ||\
+ defined(STM32F446xx) || defined(STM32F469xx) || defined(STM32F479xx)
#define IS_RCC_PLLI2SQ_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 15))
#define IS_RCC_PLLSAIN_VALUE(VALUE) ((49 <= (VALUE)) && ((VALUE) <= 432))
@@ -2622,14 +4613,34 @@
((VALUE) == RCC_PLLSAIDIVR_4) ||\
((VALUE) == RCC_PLLSAIDIVR_8) ||\
((VALUE) == RCC_PLLSAIDIVR_16))
-#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */
-
-#if defined(STM32F446xx) || defined(STM32F411xE)
+#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F411xE) || defined(STM32F446xx)
#define IS_RCC_PLLI2SM_VALUE(VALUE) ((VALUE) <= 63)
#define IS_RCC_LSE_MODE(MODE) (((MODE) == RCC_LSE_LOWPOWER_MODE) ||\
((MODE) == RCC_LSE_HIGHDRIVE_MODE))
-#endif /* STM32F446xx || STM32F411xE */
+#endif /* STM32F411xE || STM32F446xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+#define IS_RCC_PLLR_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 7))
+
+#define IS_RCC_LSE_MODE(MODE) (((MODE) == RCC_LSE_LOWPOWER_MODE) ||\
+ ((MODE) == RCC_LSE_HIGHDRIVE_MODE))
+
+#define IS_RCC_FMPI2C1CLKSOURCE(SOURCE) (((SOURCE) == RCC_FMPI2C1CLKSOURCE_APB) ||\
+ ((SOURCE) == RCC_FMPI2C1CLKSOURCE_SYSCLK) ||\
+ ((SOURCE) == RCC_FMPI2C1CLKSOURCE_HSI))
+
+#define IS_RCC_LPTIM1CLKSOURCE(SOURCE) (((SOURCE) == RCC_LPTIM1CLKSOURCE_PCLK) ||\
+ ((SOURCE) == RCC_LPTIM1CLKSOURCE_HSI) ||\
+ ((SOURCE) == RCC_LPTIM1CLKSOURCE_LSI) ||\
+ ((SOURCE) == RCC_LPTIM1CLKSOURCE_LSE))
+
+#define IS_RCC_I2SAPBCLKSOURCE(SOURCE) (((SOURCE) == RCC_I2SAPBCLKSOURCE_PLLR) ||\
+ ((SOURCE) == RCC_I2SAPBCLKSOURCE_EXT) ||\
+ ((SOURCE) == RCC_I2SAPBCLKSOURCE_PLLSRC))
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
#if defined(STM32F446xx)
#define IS_RCC_PLLR_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 7))
@@ -2679,10 +4690,46 @@
#define IS_RCC_SDIOCLKSOURCE(SOURCE) (((SOURCE) == RCC_SDIOCLKSOURCE_CK48) ||\
((SOURCE) == RCC_SDIOCLKSOURCE_SYSCLK))
-#define IS_RCC_SPDIFRXCLKSOURCE(SOURCE) (((SOURCE) == RCC_SPDIFRXCLKSOURCE_PLLR) ||\
+#define IS_RCC_SPDIFRXCLKSOURCE(SOURCE) (((SOURCE) == RCC_SPDIFRXCLKSOURCE_PLLR) ||\
((SOURCE) == RCC_SPDIFRXCLKSOURCE_PLLI2SP))
-#endif /* STM32F446xx */
-
+#endif /* STM32F446xx */
+
+#if defined(STM32F469xx) || defined(STM32F479xx)
+#define IS_RCC_PLLR_VALUE(VALUE) ((2 <= (VALUE)) && ((VALUE) <= 7))
+
+#define IS_RCC_PLLSAIP_VALUE(VALUE) (((VALUE) == RCC_PLLSAIP_DIV2) ||\
+ ((VALUE) == RCC_PLLSAIP_DIV4) ||\
+ ((VALUE) == RCC_PLLSAIP_DIV6) ||\
+ ((VALUE) == RCC_PLLSAIP_DIV8))
+
+#define IS_RCC_CK48CLKSOURCE(SOURCE) (((SOURCE) == RCC_CK48CLKSOURCE_PLLQ) ||\
+ ((SOURCE) == RCC_CK48CLKSOURCE_PLLSAIP))
+
+#define IS_RCC_SDIOCLKSOURCE(SOURCE) (((SOURCE) == RCC_SDIOCLKSOURCE_CK48) ||\
+ ((SOURCE) == RCC_SDIOCLKSOURCE_SYSCLK))
+
+#define IS_RCC_DSIBYTELANECLKSOURCE(SOURCE) (((SOURCE) == RCC_DSICLKSOURCE_PLLR) ||\
+ ((SOURCE) == RCC_DSICLKSOURCE_DSIPHY))
+
+#define IS_RCC_LSE_MODE(MODE) (((MODE) == RCC_LSE_LOWPOWER_MODE) ||\
+ ((MODE) == RCC_LSE_HIGHDRIVE_MODE))
+#endif /* STM32F469xx || STM32F479xx */
+
+#if defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx) || \
+ defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) || \
+ defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE) || defined(STM32F446xx) || \
+ defined(STM32F469xx) || defined(STM32F479xx)
+
+#define IS_RCC_MCO2SOURCE(SOURCE) (((SOURCE) == RCC_MCO2SOURCE_SYSCLK) || ((SOURCE) == RCC_MCO2SOURCE_PLLI2SCLK)|| \
+ ((SOURCE) == RCC_MCO2SOURCE_HSE) || ((SOURCE) == RCC_MCO2SOURCE_PLLCLK))
+
+#endif /* STM32F405xx || STM32F415xx || STM32F407xx || STM32F417xx || STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx ||
+ STM32F401xC || STM32F401xE || STM32F411xE || STM32F446xx || STM32F469xx || STM32F479xx */
+
+#if defined(STM32F410Tx) || defined(STM32F410Cx) || defined(STM32F410Rx)
+#define IS_RCC_MCO2SOURCE(SOURCE) (((SOURCE) == RCC_MCO2SOURCE_SYSCLK) || ((SOURCE) == RCC_MCO2SOURCE_I2SCLK)|| \
+ ((SOURCE) == RCC_MCO2SOURCE_HSE) || ((SOURCE) == RCC_MCO2SOURCE_PLLCLK))
+#endif /* STM32F410Tx || STM32F410Cx || STM32F410Rx */
/**
* @}
*/