Revision 0:e3e886021c90, committed 2020-07-15

Comitter:

r08522622

Date:

Wed Jul 15 11:18:13 2020 +0000

Commit message:

edit parameters

Changed in this revision

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/Encoder.h	Wed Jul 15 11:18:13 2020 +0000
@@ -0,0 +1,6 @@
+#ifndef ENCODER_H
+#define ENCODER_H
+
+void EncoderInit(TIM_Encoder_InitTypeDef * encoder, TIM_HandleTypeDef * timer, TIM_TypeDef * TIMx, uint32_t maxcount, uint32_t encmode);
+
+#endif
\ No newline at end of file

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/EncoderInit.cpp	Wed Jul 15 11:18:13 2020 +0000
@@ -0,0 +1,35 @@
+#include "mbed.h"
+
+void EncoderInit(TIM_Encoder_InitTypeDef * encoder, TIM_HandleTypeDef * timer, TIM_TypeDef * TIMx, uint32_t maxcount, uint32_t encmode)
+{
+
+    timer->Instance = TIMx;
+    timer->Init.Period = maxcount;
+    timer->Init.CounterMode = TIM_COUNTERMODE_UP;
+    timer->Init.Prescaler = 0;
+    timer->Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
+
+    encoder->EncoderMode = encmode;
+
+    encoder->IC1Filter = 0x0F;
+    encoder->IC1Polarity = TIM_INPUTCHANNELPOLARITY_RISING;
+    encoder->IC1Prescaler = TIM_ICPSC_DIV4;
+    encoder->IC1Selection = TIM_ICSELECTION_DIRECTTI;
+
+    encoder->IC2Filter = 0x0F;
+    encoder->IC2Polarity = TIM_INPUTCHANNELPOLARITY_FALLING;
+    encoder->IC2Prescaler = TIM_ICPSC_DIV4;
+    encoder->IC2Selection = TIM_ICSELECTION_DIRECTTI;
+
+
+    if (HAL_TIM_Encoder_Init(timer, encoder) != HAL_OK) {
+        printf("Couldn't Init Encoder\r\n");
+        while (1) {}
+    }
+
+    if(HAL_TIM_Encoder_Start(timer,TIM_CHANNEL_1)!=HAL_OK) {
+        printf("Couldn't Start Encoder\r\n");
+        while (1) {}
+    }
+}
+

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/EncoderMspInitF4.cpp	Wed Jul 15 11:18:13 2020 +0000
@@ -0,0 +1,76 @@
+#include "mbed.h"
+/*
+ * HAL_TIM_Encoder_MspInit()
+ * Overrides the __weak function stub in stm32f4xx_hal_tim.h
+ *
+ * Edit the below for your preferred pin wiring & pullup/down
+ * I have encoder common at 3V3, using GPIO_PULLDOWN on inputs.
+ * Encoder A&B outputs connected directly to GPIOs.
+ *
+ * www.st.com/st-web-ui/static/active/en/resource/technical/document/datasheet/DM00102166.pdf
+ * www.st.com/st-web-ui/static/active/en/resource/technical/document/datasheet/DM00141306.pdf
+ *
+ * TIM1_CH1: AF1 @ PA_8, PE_9 
+ * TIM1_CH2: AF1 @ PA_9, PE_11 
+ *
+ * TIM2_CH1: AF1 @ PA_0, PA_5, PA_15, PB_8*     *F446 only
+ * TIM2_CH2: AF1 @ PA_1, PB_3, PB_9*            *F446 only
+ *
+ * TIM3_CH1: AF2 @ PA_6, PB_4, PC_6
+ * TIM3_CH2: AF2 @ PA_7, PB_5, PC_7
+ *
+ * TIM4_CH1: AF2 @ PB_6, PD_12
+ * TIM4_CH2: AF2 @ PB_7, PD_13
+ *
+ * TIM5_CH1: AF2 @ PA_0*    *TIM5 used by mbed system ticker so unavailable
+ * TIM5_CH2: AF2 @ PA_1*
+ *
+ */
+
+#ifdef TARGET_STM32F4
+void HAL_TIM_Encoder_MspInit(TIM_HandleTypeDef *htim)
+{
+    GPIO_InitTypeDef GPIO_InitStruct;
+
+    if (htim->Instance == TIM1) { //PA8 PA9 = Nucleo D7 D8
+        __TIM1_CLK_ENABLE();
+        __GPIOA_CLK_ENABLE();
+        GPIO_InitStruct.Pin = GPIO_PIN_8 | GPIO_PIN_9;
+        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+        GPIO_InitStruct.Alternate = GPIO_AF1_TIM1;
+        HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+    }
+    else if (htim->Instance == TIM2) { //PA0 PA1 = Nucleo A0 A1
+        __TIM2_CLK_ENABLE();
+        __GPIOA_CLK_ENABLE();
+        GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1;
+        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+        GPIO_InitStruct.Alternate = GPIO_AF1_TIM2;
+        HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+    }
+    else if (htim->Instance == TIM3) { //PA6 PA7 = Nucleo D12 D11
+        __TIM3_CLK_ENABLE();
+        __GPIOB_CLK_ENABLE();
+        GPIO_InitStruct.Pin = GPIO_PIN_6 | GPIO_PIN_7;
+        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+        GPIO_InitStruct.Alternate = GPIO_AF2_TIM3;
+        HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+    }
+    else if (htim->Instance == TIM4) { // PB6 PB7 = Nucleo D10 MORPHO_PB7
+        __TIM4_CLK_ENABLE();
+        __GPIOB_CLK_ENABLE();
+        GPIO_InitStruct.Pin = GPIO_PIN_6 | GPIO_PIN_7;
+        GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+        GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+        GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+        GPIO_InitStruct.Alternate = GPIO_AF2_TIM4;
+        HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+    }
+}
+#endif
\ No newline at end of file