Forked repository for pushing changes to EVAL-AD4696
Dependencies: platform_drivers
app/app_config.h
- Committer:
- pmallick
- Date:
- 2021-09-30
- Revision:
- 1:8792acb5a039
File content as of revision 1:8792acb5a039:
/*************************************************************************//** * @file app_config.h * @brief Configuration file for AD4696 device applications ****************************************************************************** * Copyright (c) 2021 Analog Devices, Inc. * * All rights reserved. * * This software is proprietary to Analog Devices, Inc. and its licensors. * By using this software you agree to the terms of the associated * Analog Devices Software License Agreement. *****************************************************************************/ #ifndef APP_CONFIG_H #define APP_CONFIG_H /******************************************************************************/ /***************************** Include Files **********************************/ /******************************************************************************/ #include <stdint.h> /******************************************************************************/ /********************** Macros and Constants Definition ***********************/ /******************************************************************************/ /* List of supported platforms*/ #define MBED_PLATFORM 1 /* Select the active platform */ #define ACTIVE_PLATFORM MBED_PLATFORM #if (ACTIVE_PLATFORM == MBED_PLATFORM) #include "app_config_mbed.h" /* Used to form a VCOM serial number */ #define FIRMWARE_NAME "ad4696_mbed_iio_application" /* Redefine the init params structure mapping w.r.t. platform */ #define bsy_gpio_extra_init_params mbed_gpio_bsy_extra_init_params #define ext_int_extra_init_params mbed_ext_int_extra_init_params #define uart_extra_init_params mbed_uart_extra_init_params #define spi_extra_init_params mbed_spi_extra_init_params #else #error "No/Invalid active platform selected" #endif // **** Note for User: ACTIVE_DEVICE selection **** // /* Define the device type here from the list of below device type defines * (one at a time. Defining more than one device can result into compile error). * e.g. #define DEV_AD4696 -> This will make AD4696 as an ACTIVE_DEVICE. * The ACTIVE_DEVICE is default set to AD4696 if device type is not defined. * */ //#define DEV_AD4696 #if defined(DEV_AD4696) #define ACTIVE_DEVICE ID_AD4696 #define ACTIVE_DEVICE_NAME "AD4696" #elif defined(DEV_AD4695) #define ACTIVE_DEVICE ID_AD4695 #define ACTIVE_DEVICE_NAME "AD4695" #else #warning No/Unsupported ADxxxxy symbol defined. AD4696 defined #define DEV_AD4696 #define ACTIVE_DEVICE ID_AD4696 #define ACTIVE_DEVICE_NAME "AD4696" #endif #if defined(DEV_AD4696) #define NO_OF_CHANNELS 16 #define ADC_RESOLUTION 16 #elif defined(DEV_AD4695) #define NO_OF_CHANNELS 16 #define ADC_RESOLUTION 16 #else /* Default config for AD4696 */ #define NO_OF_CHANNELS 16 #define ADC_RESOLUTION 16 #endif // **** Note for User: Polarity Mode selection **** // /* Since the pin pairing option is same for all the channels in * standard sequencer mode, hence polarity mode for all the * channels is also kept same to avoid stale ADC output codes. * Make sure to change the JP6 jumper position on the Eval board to A * to use the PSEUDO_BIPOLAR_MODE. * * Select Pseudo bipolar mode (default is unipolar mode) for all the channels. * e.g. #define PSEUDO_BIPOLAR_MODE -> This will enable the PSEUDO_BIPOLAR_MODE * for all the channels. * */ //#define PSEUDO_BIPOLAR_MODE /* Pins to be used an interrupt to trigger callback function */ #define EXT_TRIGGER_PIN CONVST_PIN /* ADC max count (full scale value) for unipolar inputs */ #define ADC_MAX_COUNT_UNIPOLAR (uint32_t)((1 << ADC_RESOLUTION) - 1) /* ADC max count (full scale value) for bipolar inputs */ #define ADC_MAX_COUNT_BIPOLAR (uint32_t)(1 << (ADC_RESOLUTION-1)) /* Baud rate for IIO application UART interface */ #define IIO_UART_BAUD_RATE (230400) /****** Macros used to form a VCOM serial number ******/ #if !defined(DEVICE_NAME) #define DEVICE_NAME "DEV_AD4696" #endif #if !defined(PLATFORM_NAME) #define PLATFORM_NAME "SDP_K1" #endif /******/ /* Enable the VirtualCOM port connection/interface. By default serial communication * is physical UART */ //#define USE_VIRTUAL_COM_PORT #if defined(USE_VIRTUAL_COM_PORT) /* Below USB configurations (VID and PID) are owned and assigned by ADI. * If intended to distribute software further, use the VID and PID owned by your * organization */ #define VIRTUAL_COM_PORT_VID 0x0456 #define VIRTUAL_COM_PORT_PID 0xb66c /* Serial number string is formed as: application name + device (target) name + platform (host) name */ #define VIRTUAL_COM_SERIAL_NUM (FIRMWARE_NAME "_" DEVICE_NAME "_" PLATFORM_NAME) #endif /******************************************************************************/ /********************** Variables and User Defined Data Types *****************/ /******************************************************************************/ /******************************************************************************/ /************************ Public Declarations *********************************/ /******************************************************************************/ /* UART init parameters structure */ extern struct uart_init_param uart_init_params; /* PWM descriptor */ extern struct pwm_desc *pwm_desc; /* Initializing system peripherals */ int32_t init_system(void); #endif //APP_CONFIG_H