File content as of revision 2:cfeb4c9cdbe3:

/* RF12B Library. Based on work done by JeeLabs.org ported to mbed by SK Pang.
http://jeelabs.net/projects/cafe/wiki/RF12

http://opensource.org/licenses/mit-license.php

Jan 2012 skpang.co.uk

*/

#include "RF12B.h"

// RF12 command codes
#define RF_RECEIVER_ON  0x82DD
#define RF_XMITTER_ON   0x823D
#define RF_IDLE_MODE    0x820D
#define RF_SLEEP_MODE   0x8205
#define RF_WAKEUP_MODE  0x8207
#define RF_TXREG_WRITE  0xB800
#define RF_RX_FIFO_READ 0xB000
#define RF_WAKEUP_TIMER 0xE000

// RF12 status bits
#define RF_LBD_BIT      0x0400
#define RF_RSSI_BIT     0x0100

// bits in the node id configuration byte
#define NODE_BAND       0xC0        // frequency band
#define NODE_ACKANY     0x20        // ack on broadcast packets if set
#define NODE_ID         0x1F        // id of this node, as A..Z or 1..31

// transceiver states, these determine what to do with each interrupt
enum {
    TXCRC1, TXCRC2, TXTAIL, TXDONE, TXIDLE,
    TXRECV,
    TXPRE1, TXPRE2, TXPRE3, TXSYN1, TXSYN2,
};

DigitalOut rfled(LED3);
DigitalOut t1(p5);
DigitalOut t2(p6);

RF12B::RF12B(PinName _SDI,
             PinName _SDO,
             PinName _SCK,
             PinName _NCS,
             PinName _NIRQ):spi(_SDI, _SDO, _SCK),
        NCS(_NCS), NIRQ(_NIRQ), NIRQ_in(_NIRQ), rfled(LED3),t1(p5),t2(p6) {

    /* SPI frequency, word lenght, polarity and phase */
    spi.format(8,0);
    spi.frequency(2000000);

    /* Set ~CS high */
    NCS = 1;

    /* Setup interrupt to happen on falling edge of NIRQ */
    NIRQ.fall(this, &RF12B::rxISR);
}


/**********************************************************************
 *  PRIVATE FUNCTIONS
 *********************************************************************/

/* Initialises the RF12B module */
void RF12B::init(uint8_t id, uint8_t band, uint8_t g) {
  
    nodeid = id;
    group = g;
    rf12_grp = g; 
    
    writeCmd(0x0000); // intitial SPI transfer added to avoid power-up problem
    writeCmd(RF_SLEEP_MODE); // DC (disable clk pin), enable lbd
    
    // wait until RFM12B is out of power-up reset, this takes several *seconds*
    writeCmd(RF_TXREG_WRITE); // in case we're still in OOK mode
      
    while (NIRQ == 0)  writeCmd(0x0000);
        
    writeCmd(0x80C7 | (2 << 4)); // EL (ena TX), EF (ena RX FIFO), 12.0pF 
    writeCmd(0xA640); // 868MHz 
    writeCmd(0xC606); // approx 49.2 Kbps, i.e. 10000/29/(1+6) Kbps
    writeCmd(0x94A2); // VDI,FAST,134kHz,0dBm,-91dBm 
    writeCmd(0xC2AC); // AL,!ml,DIG,DQD4 
   
    writeCmd(0xCA83); // FIFO8,2-SYNC,!ff,DR 
    writeCmd(0xCE00 | group); // SYNC=2DXX&#65307; 
    
    writeCmd(0xC483); // @PWR,NO RSTRIC,!st,!fi,OE,EN 
    writeCmd(0x9850); // !mp,90kHz,MAX OUT 
    writeCmd(0xCC77); // OB1&#65292;OB0, LPX,&#65281;ddy&#65292;DDIT&#65292;BW0 
    writeCmd(0xE000); // NOT USE 
    writeCmd(0xC800); // NOT USE 
    writeCmd(0xC049); // 1.66MHz,3.1V 

    rxstate = TXIDLE;
       
    rfled = 0;
}

/* Write a command to the RF Module */
unsigned int RF12B::writeCmd(unsigned int cmd) {
    NCS = 0;
    unsigned int recv = spi.write(cmd >>8);
    recv = spi.write(cmd);
    NCS = 1;
    return recv;
}

/* Sends a byte of data across RF */
void RF12B::send(unsigned char data) {
   while (NIRQ);
   writeCmd(0xB800 + data);
}


/* Interrupt routine for data reception and Txing */
void RF12B::rxISR() {

   // a transfer of 2x 16 bits @ 2 MHz over SPI takes 2x 8 us inside this ISR
    writeCmd(0x0000);
    
    if (rxstate == TXRECV) {
        uint8_t in = rf12_xfer(RF_RX_FIFO_READ);

        if (rxfill == 0 && group != 0)
            rf12_buf[rxfill++] = group;
            
        rf12_buf[rxfill++] = in;
        rf12_crc = _crc16_update(rf12_crc, in);

        if (rxfill >= rf12_len + 5 || rxfill >= RF_MAX)
            rf12_xfer(RF_IDLE_MODE);
    } else {
        uint8_t out;

        if (rxstate < 0) {
            uint8_t pos = 3 + rf12_len + rxstate++;
            out = rf12_buf[pos];
            rf12_crc = _crc16_update(rf12_crc, out);
        } else
            switch (rxstate++) {
                case TXSYN1: out = 0x2D; break;
                case TXSYN2: out = rf12_grp; rxstate = - (2 + rf12_len); break;
                case TXCRC1: out = rf12_crc; break;
                case TXCRC2: out = rf12_crc >> 8; break;
                case TXDONE: rf12_xfer(RF_IDLE_MODE); // fall through
                default: out = 0xAA;
            }
       
        rf12_xfer(RF_TXREG_WRITE + out);
    }
 }


void RF12B::rf12_sendStart (uint8_t hdr, const void* ptr, uint8_t len)
{
    rf12_len = len;
    memcpy((void*) rf12_data, ptr, len);
  
    rf12_sendStart2(hdr);

}
void RF12B::rf12_sendStart2 (uint8_t hdr) {
    rf12_hdr = hdr & RF12_HDR_DST ? hdr :
                (hdr & ~RF12_HDR_MASK) + (nodeid & NODE_ID);
 
 /*   if (crypter != 0)
        crypter(1);
 */   
    rf12_crc = ~0;

    rf12_crc = _crc16_update(rf12_crc, rf12_grp);
    rxstate = TXPRE1;
      
    rf12_xfer(RF_XMITTER_ON); // bytes will be fed via interrupts
}


 uint16_t RF12B::rf12_xfer (uint16_t cmd) {
    NCS = 0;
    uint16_t reply = rf12_byte(cmd >> 8) << 8;
    reply |= rf12_byte(cmd);
    NCS = 1;
    return reply;
}

 void RF12B::rf12_recvStart (void) {
    rxfill = rf12_len = 0;
    rf12_crc = ~0;

    if (group != 0)
        rf12_crc = _crc16_update(~0, group);

    rxstate = TXRECV;    
    rf12_xfer(RF_RECEIVER_ON);
}
uint16_t RF12B::check_crc(void)
{

    return rf12_crc;
}
uint8_t RF12B::length(void)
{

    return rf12_len;
}
 uint8_t* RF12B::get_data(void)
{
    return  (uint8_t*)rf12_data;

}


uint8_t  RF12B::rf12_recvDone (void) {
    
     if (rxstate == TXRECV && (rxfill >= rf12_len + 5 || rxfill >= RF_MAX)) {
        rxstate = TXIDLE;
 
        if (rf12_len > RF12_MAXDATA)
            rf12_crc = 1; // force bad crc if packet length is invalid
        if (!(rf12_hdr & RF12_HDR_DST) || (nodeid & NODE_ID) == 31 ||
                (rf12_hdr & RF12_HDR_MASK) == (nodeid & NODE_ID)) {
                /*
                for(i=0;i<rf12_len+6;i++)
                {
                    printf("%X ",rf12_buf[i]);
                }
                printf(" crc:%x",rf12_crc);
                */
           /*     
            if (rf12_crc == 0 && crypter != 0)
                crypter(0);
            else
                rf12_seq = -1;
                 */
            return 1; // it's a broadcast packet or it's addressed to this node
           
        }
    }
    if (rxstate == TXIDLE)
        rf12_recvStart();
    return 0;
}

uint8_t RF12B::rf12_byte(uint8_t out)
{
  unsigned char recv = spi.write(out);
 
    return recv;
}
 
uint16_t RF12B::_crc16_update(uint16_t crc, uint8_t data) {
    int i;

    crc ^= data;
    for (i = 0; i < 8; ++i)
    {
        if (crc & 1)
        crc = (crc >> 1) ^ 0xA001;
        else
        crc = (crc >> 1);
    }

    return crc;
}