Pablo Henrique
code for read VL53l0x sensor with CAN
Diff: VL53L0X_simple/VL53L0X_2nd.h
- Revision:
- 1:7bbfe329c62b
- Parent:
- 0:44429c0a71d4
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/VL53L0X_simple/VL53L0X_2nd.h Mon Mar 18 22:45:39 2019 +0000
@@ -0,0 +1,1446 @@
+
+ /**
+ * @brief Start the measure indicated by operating mode
+ * @param[in] operating_mode specifies requested measure
+ * @param[in] fptr specifies call back function must be !NULL in case of interrupt measure
+ * @return "0" on success
+ */
+ int start_measurement(OperatingMode operating_mode, void (*fptr)(void));
+
+ /**
+ * @brief Get results for the measure indicated by operating mode
+ * @param[in] operating_mode specifies requested measure results
+ * @param[out] p_data pointer to the MeasureData_t structure to read data in to
+ * @return "0" on success
+ */
+ int get_measurement(OperatingMode operating_mode, VL53L0X_RangingMeasurementData_t *p_data);
+
+ /**
+ * @brief Stop the currently running measure indicate by operating_mode
+ * @param[in] operating_mode specifies requested measure to stop
+ * @return "0" on success
+ */
+ int stop_measurement(OperatingMode operating_mode);
+
+ /**
+ * @brief Interrupt handling func to be called by user after an INT is occourred
+ * @param[in] opeating_mode indicating the in progress measure
+ * @param[out] Data pointer to the MeasureData_t structure to read data in to
+ * @return "0" on success
+ */
+ int handle_irq(OperatingMode operating_mode, VL53L0X_RangingMeasurementData_t *data);
+
+ /**
+ * @brief Enable interrupt measure IRQ
+ * @return "0" on success
+ */
+ void enable_interrupt_measure_detection_irq(void)
+ {
+ if (_gpio1Int != NULL) {
+ _gpio1Int->enable_irq();
+ }
+ }
+
+ /**
+ * @brief Disable interrupt measure IRQ
+ * @return "0" on success
+ */
+ void disable_interrupt_measure_detection_irq(void)
+ {
+ if (_gpio1Int != NULL) {
+ _gpio1Int->disable_irq();
+ }
+ }
+
+ /**
+ * @brief Attach a function to call when an interrupt is detected, i.e. measurement is ready
+ * @param[in] fptr pointer to call back function to be called whenever an interrupt occours
+ * @return "0" on success
+ */
+ void attach_interrupt_measure_detection_irq(void (*fptr)(void))
+ {
+ if (_gpio1Int != NULL) {
+ _gpio1Int->rise(fptr);
+ }
+ }
+
+
+ /** Wrapper functions */
+ /** @defgroup api_init Init functions
+ * @brief API init functions
+ * @ingroup api_hl
+ * @{
+ */
+
+ /**
+ *
+ * @brief One time device initialization
+ *
+ * To be called once and only once after device is brought out of reset (Chip enable) and booted.
+ *
+ * @par Function Description
+ * When not used after a fresh device "power up" or reset, it may return @a #CALIBRATION_WARNING
+ * meaning wrong calibration data may have been fetched from device that can result in ranging offset error\n
+ * If application cannot execute device reset or need to run VL53L0X_data_init multiple time
+ * then it must ensure proper offset calibration saving and restore on its own
+ * by using @a VL53L0X_get_offset_calibration_data_micro_meter() on first power up and then @a VL53L0X_set_offset_calibration_data_micro_meter() all all subsequent init
+ *
+ * @param void
+ * @return "0" on success, @a #CALIBRATION_WARNING if failed
+ */
+ virtual int init(void *init)
+ {
+ return VL53L0X_data_init(_device);
+ }
+
+ /**
+ * @brief Prepare device for operation
+ * @par Function Description
+ * Does static initialization and reprogram common default settings \n
+ * Device is prepared for new measure, ready single shot ranging or ALS typical polling operation\n
+ * After prepare user can : \n
+ * @li Call other API function to set other settings\n
+ * @li Configure the interrupt pins, etc... \n
+ * @li Then start ranging or ALS operations in single shot or continuous mode
+ *
+ * @param void
+ * @return "0" on success
+ */
+ int prepare()
+ {
+ VL53L0X_Error status = VL53L0X_ERROR_NONE;
+ uint32_t ref_spad_count;
+ uint8_t is_aperture_spads;
+ uint8_t vhv_settings;
+ uint8_t phase_cal;
+
+ if (status == VL53L0X_ERROR_NONE) {
+ //printf("Call of VL53L0X_StaticInit\r\n");
+ status = VL53L0X_static_init(_device); // Device Initialization
+ }
+
+ if (status == VL53L0X_ERROR_NONE) {
+ //printf("Call of VL53L0X_PerformRefCalibration\r\n");
+ status = VL53L0X_perform_ref_calibration(_device,
+ &vhv_settings, &phase_cal); // Device Initialization
+ }
+
+ if (status == VL53L0X_ERROR_NONE) {
+ //printf("Call of VL53L0X_PerformRefSpadManagement\r\n");
+ status = VL53L0X_perform_ref_spad_management(_device,
+ &ref_spad_count, &is_aperture_spads); // Device Initialization
+// printf ("refSpadCount = %d, isApertureSpads = %d\r\n", refSpadCount, isApertureSpads);
+ }
+
+ return status;
+ }
+
+ /**
+ * @brief Start continuous ranging mode
+ *
+ * @details End user should ensure device is in idle state and not already running
+ * @return "0" on success
+ */
+ int range_start_continuous_mode()
+ {
+ int status;
+ status = VL53L0X_set_device_mode(_device, VL53L0X_DEVICEMODE_CONTINUOUS_RANGING);
+
+ if (status == VL53L0X_ERROR_NONE) {
+ //printf ("Call of VL53L0X_StartMeasurement\r\n");
+ status = VL53L0X_start_measurement(_device);
+ }
+
+ return status;
+ }
+
+//------- Feburary 4th, 2018 by JH1PJL / K.Arai --------------------------------
+#if ORIGINAL
+ /**
+ * @brief Get ranging result and only that
+ *
+ * @par Function Description
+ * Unlike @a VL53L0X_get_ranging_measurement_data() this function only retrieves the range in millimeter \n
+ * It does any required up-scale translation\n
+ * It can be called after success status polling or in interrupt mode \n
+ * @warning these function is not doing wrap around filtering \n
+ * This function doesn't perform any data ready check!
+ *
+ * @param p_data Pointer to range distance
+ * @return "0" on success
+ */
+ virtual int get_distance(uint32_t *p_data)
+ {
+ int status = 0;
+ VL53L0X_RangingMeasurementData_t p_ranging_measurement_data;
+
+ status = start_measurement(range_single_shot_polling, NULL);
+ if (!status) {
+ status = get_measurement(range_single_shot_polling, &p_ranging_measurement_data);
+ }
+ if (p_ranging_measurement_data.RangeStatus == 0) {
+ // we have a valid range.
+ *p_data = p_ranging_measurement_data.RangeMilliMeter;
+ } else {
+ *p_data = 0;
+ status = VL53L0X_ERROR_RANGE_ERROR;
+ }
+ stop_measurement(range_single_shot_polling);
+ return status;
+ }
+#endif
+
+ /** @} */
+
+ /**
+ * @brief Set new device i2c address
+ *
+ * After completion the device will answer to the new address programmed.
+ *
+ * @param new_addr The new i2c address (7bit)
+ * @return "0" on success
+ */
+ int set_device_address(int new_addr)
+ {
+ int status;
+
+ status = VL53L0X_set_device_address(_device, new_addr);
+ if (!status) {
+ _device->I2cDevAddr = new_addr;
+ }
+ return status;
+
+ }
+
+ /**
+ * @brief Clear given system interrupt condition
+ *
+ * @par Function Description
+ * Clear given interrupt cause by writing into register #SYSTEM_INTERRUPT_CLEAR register.
+ * @param dev The device
+ * @param int_clear Which interrupt source to clear. Use any combinations of #INTERRUPT_CLEAR_RANGING , #INTERRUPT_CLEAR_ALS , #INTERRUPT_CLEAR_ERROR.
+ * @return "0" on success
+ */
+ int clear_interrupt(uint8_t int_clear)
+ {
+ return VL53L0X_clear_interrupt_mask(_device, int_clear);
+ }
+
+ /**
+ *
+ * @brief Get the 53L0 device
+ *
+ * To be called to retrive the internal device descriptor to allow usage of
+ * low level API having device as parameter. To be called after set_device_address()
+ * (if any).
+ *
+ * @par Function Description
+ * To be called if low level API usage is needed as those functions requires
+ * device as a parameter.TICINIT.
+ *
+ * @note This function return a pointer to an object internal structure
+ *
+ * @param dev ptr to ptr to Device Handle
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error vl53l0x_get_device(VL53L0X_DEV *dev)
+{
+ *dev = _device;
+ return VL53L0X_ERROR_NONE;
+}
+
+ /**
+ *
+ * @brief One time device initialization
+ *
+ * To be called once and only once after device is brought out of reset
+ * (Chip enable) and booted see @a VL53L0X_WaitDeviceBooted()
+ *
+ * @par Function Description
+ * When not used after a fresh device "power up" or reset, it may return
+ * @a #VL53L0X_ERROR_CALIBRATION_WARNING meaning wrong calibration data
+ * may have been fetched from device that can result in ranging offset error\n
+ * If application cannot execute device reset or need to run VL53L0X_DataInit
+ * multiple time then it must ensure proper offset calibration saving and
+ * restore on its own by using @a VL53L0X_GetOffsetCalibrationData() on first
+ * power up and then @a VL53L0X_SetOffsetCalibrationData() in all subsequent init
+ * This function will change the VL53L0X_State from VL53L0X_STATE_POWERDOWN to
+ * VL53L0X_STATE_WAIT_STATICINIT.
+ *
+ * @note This function accesses to the device
+ *
+ * @param dev Device Handle
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_data_init(VL53L0X_DEV dev);
+
+ /**
+ * @brief Do basic device init (and eventually patch loading)
+ * This function will change the VL53L0X_State from
+ * VL53L0X_STATE_WAIT_STATICINIT to VL53L0X_STATE_IDLE.
+ * In this stage all default setting will be applied.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_static_init(VL53L0X_DEV dev);
+
+ /**
+ * @brief Perform Reference Calibration
+ *
+ * @details Perform a reference calibration of the Device.
+ * This function should be run from time to time before doing
+ * a ranging measurement.
+ * This function will launch a special ranging measurement, so
+ * if interrupt are enable an interrupt will be done.
+ * This function will clear the interrupt generated automatically.
+ *
+ * @warning This function is a blocking function
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_vhv_settings Pointer to vhv settings parameter.
+ * @param p_phase_cal Pointer to PhaseCal parameter.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_perform_ref_calibration(VL53L0X_DEV dev, uint8_t *p_vhv_settings,
+ uint8_t *p_phase_cal);
+
+ /**
+ * @brief Get Reference Calibration Parameters
+ *
+ * @par Function Description
+ * Get Reference Calibration Parameters.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_vhv_settings Pointer to VHV parameter
+ * @param p_phase_cal Pointer to PhaseCal Parameter
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_ref_calibration(VL53L0X_DEV dev,
+ uint8_t *p_vhv_settings, uint8_t *p_phase_cal);
+
+ VL53L0X_Error VL53L0X_set_ref_calibration(VL53L0X_DEV dev,
+ uint8_t vhv_settings, uint8_t phase_cal);
+
+ /**
+ * @brief Performs Reference Spad Management
+ *
+ * @par Function Description
+ * The reference SPAD initialization procedure determines the minimum amount
+ * of reference spads to be enables to achieve a target reference signal rate
+ * and should be performed once during initialization.
+ *
+ * @note This function Access to the device
+ *
+ * @note This function change the device mode to
+ * VL53L0X_DEVICEMODE_SINGLE_RANGING
+ *
+ * @param dev Device Handle
+ * @param ref_spad_count Reports ref Spad Count
+ * @param is_aperture_spads Reports if spads are of type
+ * aperture or non-aperture.
+ * 1:=aperture, 0:=Non-Aperture
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_REF_SPAD_INIT Error in the Ref Spad procedure.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_perform_ref_spad_management(VL53L0X_DEV dev,
+ uint32_t *ref_spad_count, uint8_t *is_aperture_spads);
+
+ /**
+ * @brief Applies Reference SPAD configuration
+ *
+ * @par Function Description
+ * This function applies a given number of reference spads, identified as
+ * either Aperture or Non-Aperture.
+ * The requested spad count and type are stored within the device specific
+ * parameters data for access by the host.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param refSpadCount Number of ref spads.
+ * @param is_aperture_spads Defines if spads are of type
+ * aperture or non-aperture.
+ * 1:=aperture, 0:=Non-Aperture
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_REF_SPAD_INIT Error in the in the reference
+ * spad configuration.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_reference_spads(VL53L0X_DEV dev,
+ uint32_t refSpadCount, uint8_t is_aperture_spads);
+
+ /**
+ * @brief Retrieves SPAD configuration
+ *
+ * @par Function Description
+ * This function retrieves the current number of applied reference spads
+ * and also their type : Aperture or Non-Aperture.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_spad_count Number ref Spad Count
+ * @param p_is_aperture_spads Reports if spads are of type
+ * aperture or non-aperture.
+ * 1:=aperture, 0:=Non-Aperture
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_REF_SPAD_INIT Error in the in the reference
+ * spad configuration.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_reference_spads(VL53L0X_DEV dev,
+ uint32_t *p_spad_count, uint8_t *p_is_aperture_spads);
+
+ /**
+ * @brief Get part to part calibration offset
+ *
+ * @par Function Description
+ * Should only be used after a successful call to @a VL53L0X_DataInit to backup
+ * device NVM value
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_offset_calibration_data_micro_meter Return part to part
+ * calibration offset from device (microns)
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_offset_calibration_data_micro_meter(VL53L0X_DEV dev,
+ int32_t *p_offset_calibration_data_micro_meter);
+ /**
+ * Set or over-hide part to part calibration offset
+ * \sa VL53L0X_DataInit() VL53L0X_GetOffsetCalibrationDataMicroMeter()
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_offset_calibration_data_micro_meter Offset (microns)
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_offset_calibration_data_micro_meter(VL53L0X_DEV dev,
+ int32_t offset_calibration_data_micro_meter);
+
+ VL53L0X_Error VL53L0X_perform_offset_calibration(VL53L0X_DEV dev,
+ FixPoint1616_t cal_distance_milli_meter,
+ int32_t *p_offset_micro_meter);
+
+ VL53L0X_Error VL53L0X_perform_xtalk_calibration(VL53L0X_DEV dev,
+ FixPoint1616_t xtalk_cal_distance,
+ FixPoint1616_t *p_xtalk_compensation_rate_mega_cps);
+
+ /**
+ * @brief Perform XTalk Measurement
+ *
+ * @details Measures the current cross talk from glass in front
+ * of the sensor.
+ * This functions performs a histogram measurement and uses the results
+ * to measure the crosstalk. For the function to be successful, there
+ * must be no target in front of the sensor.
+ *
+ * @warning This function is a blocking function
+ *
+ * @warning This function is not supported when the final range
+ * vcsel clock period is set below 10 PCLKS.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param timeout_ms Histogram measurement duration.
+ * @param p_xtalk_per_spad Output parameter containing the crosstalk
+ * measurement result, in MCPS/Spad.
+ * Format fixpoint 16:16.
+ * @param p_ambient_too_high Output parameter which indicate that
+ * pXtalkPerSpad is not good if the Ambient
+ * is too high.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS vcsel clock period not supported
+ * for this operation.
+ * Must not be less than 10PCLKS.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_perform_xtalk_measurement(VL53L0X_DEV dev,
+ uint32_t timeout_ms, FixPoint1616_t *p_xtalk_per_spad,
+ uint8_t *p_ambient_too_high);
+
+ /**
+ * @brief Enable/Disable Cross talk compensation feature
+ *
+ * @note This function is not Implemented.
+ * Enable/Disable Cross Talk by set to zero the Cross Talk value
+ * by using @a VL53L0X_SetXTalkCompensationRateMegaCps().
+ *
+ * @param dev Device Handle
+ * @param x_talk_compensation_enable Cross talk compensation
+ * to be set 0=disabled else = enabled
+ * @return VL53L0X_ERROR_NOT_IMPLEMENTED Not implemented
+ */
+ VL53L0X_Error VL53L0X_set_x_talk_compensation_enable(VL53L0X_DEV dev,
+ uint8_t x_talk_compensation_enable);
+
+ /**
+ * @brief Get Cross talk compensation rate
+ *
+ * @note This function is not Implemented.
+ * Enable/Disable Cross Talk by set to zero the Cross Talk value by
+ * using @a VL53L0X_SetXTalkCompensationRateMegaCps().
+ *
+ * @param dev Device Handle
+ * @param p_x_talk_compensation_enable Pointer to the Cross talk compensation
+ * state 0=disabled or 1 = enabled
+ * @return VL53L0X_ERROR_NOT_IMPLEMENTED Not implemented
+ */
+ VL53L0X_Error VL53L0X_get_x_talk_compensation_enable(VL53L0X_DEV dev,
+ uint8_t *p_x_talk_compensation_enable);
+ /**
+ * @brief Set Cross talk compensation rate
+ *
+ * @par Function Description
+ * Set Cross talk compensation rate.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param x_talk_compensation_rate_mega_cps Compensation rate in
+ * Mega counts per second
+ * (16.16 fix point) see
+ * datasheet for details
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_x_talk_compensation_rate_mega_cps(VL53L0X_DEV dev,
+ FixPoint1616_t x_talk_compensation_rate_mega_cps);
+
+ /**
+ * @brief Get Cross talk compensation rate
+ *
+ * @par Function Description
+ * Get Cross talk compensation rate.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_xtalk_compensation_rate_mega_cps Pointer to Compensation rate
+ * in Mega counts per second
+ * (16.16 fix point) see
+ * datasheet for details
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_x_talk_compensation_rate_mega_cps(VL53L0X_DEV dev,
+ FixPoint1616_t *p_xtalk_compensation_rate_mega_cps);
+
+ /**
+ * @brief Set a new device mode
+ * @par Function Description
+ * Set device to a new mode (ranging, histogram ...)
+ *
+ * @note This function doesn't Access to the device
+ *
+ * @param dev Device Handle
+ * @param device_mode New device mode to apply
+ * Valid values are:
+ * VL53L0X_DEVICEMODE_SINGLE_RANGING
+ * VL53L0X_DEVICEMODE_CONTINUOUS_RANGING
+ * VL53L0X_DEVICEMODE_CONTINUOUS_TIMED_RANGING
+ * VL53L0X_DEVICEMODE_SINGLE_HISTOGRAM
+ * VL53L0X_HISTOGRAMMODE_REFERENCE_ONLY
+ * VL53L0X_HISTOGRAMMODE_RETURN_ONLY
+ * VL53L0X_HISTOGRAMMODE_BOTH
+ *
+ *
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_MODE_NOT_SUPPORTED This error occurs when
+ * DeviceMode is not in the
+ * supported list
+ */
+ VL53L0X_Error VL53L0X_set_device_mode(VL53L0X_DEV dev, VL53L0X_DeviceModes device_mode);
+
+ /**
+ * @brief Get current new device mode
+ * @par Function Description
+ * Get actual mode of the device(ranging, histogram ...)
+ *
+ * @note This function doesn't Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_device_mode Pointer to current apply mode value
+ * Valid values are:
+ * VL53L0X_DEVICEMODE_SINGLE_RANGING
+ * VL53L0X_DEVICEMODE_CONTINUOUS_RANGING
+ * VL53L0X_DEVICEMODE_CONTINUOUS_TIMED_RANGING
+ * VL53L0X_DEVICEMODE_SINGLE_HISTOGRAM
+ * VL53L0X_HISTOGRAMMODE_REFERENCE_ONLY
+ * VL53L0X_HISTOGRAMMODE_RETURN_ONLY
+ * VL53L0X_HISTOGRAMMODE_BOTH
+ *
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_MODE_NOT_SUPPORTED This error occurs when
+ * DeviceMode is not in the
+ * supported list
+ */
+ VL53L0X_Error VL53L0X_get_device_mode(VL53L0X_DEV dev,
+ VL53L0X_DeviceModes *p_device_mode);
+
+ /**
+ * @brief Get current configuration for GPIO pin for a given device
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param pin ID of the GPIO Pin
+ * @param p_device_mode Pointer to Device Mode associated to the Gpio.
+ * @param p_functionality Pointer to Pin functionality.
+ * Refer to ::VL53L0X_GpioFunctionality
+ * @param p_polarity Pointer to interrupt polarity.
+ * Active high or active low see
+ * ::VL53L0X_InterruptPolarity
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_GPIO_NOT_EXISTING Only Pin=0 is accepted.
+ * @return VL53L0X_ERROR_GPIO_FUNCTIONALITY_NOT_SUPPORTED
+ * This error occurs
+ * when Funcionality programmed is not in the supported list:
+ * Supported value are:
+ * VL53L0X_GPIOFUNCTIONALITY_OFF,
+ * VL53L0X_GPIOFUNCTIONALITY_THRESHOLD_CROSSED_LOW,
+ * VL53L0X_GPIOFUNCTIONALITY_THRESHOLD_CROSSED_HIGH,
+ * VL53L0X_GPIOFUNCTIONALITY_THRESHOLD_CROSSED_OUT,
+ * VL53L0X_GPIOFUNCTIONALITY_NEW_MEASURE_READY
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_gpio_config(VL53L0X_DEV dev, uint8_t pin,
+ VL53L0X_DeviceModes *p_device_mode,
+ VL53L0X_GpioFunctionality *p_functionality,
+ VL53L0X_InterruptPolarity *p_polarity);
+
+ /**
+ * @brief Set the configuration of GPIO pin for a given device
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param pin ID of the GPIO Pin
+ * @param functionality Select Pin functionality.
+ * Refer to ::VL53L0X_GpioFunctionality
+ * @param device_mode Device Mode associated to the Gpio.
+ * @param polarity Set interrupt polarity. Active high
+ * or active low see ::VL53L0X_InterruptPolarity
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_GPIO_NOT_EXISTING Only Pin=0 is accepted.
+ * @return VL53L0X_ERROR_GPIO_FUNCTIONALITY_NOT_SUPPORTED This error occurs
+ * when Functionality programmed is not in the supported list:
+ * Supported value are:
+ * VL53L0X_GPIOFUNCTIONALITY_OFF,
+ * VL53L0X_GPIOFUNCTIONALITY_THRESHOLD_CROSSED_LOW,
+ * VL53L0X_GPIOFUNCTIONALITY_THRESHOLD_CROSSED_HIGH,
+ VL53L0X_GPIOFUNCTIONALITY_THRESHOLD_CROSSED_OUT,
+ * VL53L0X_GPIOFUNCTIONALITY_NEW_MEASURE_READY
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_gpio_config(VL53L0X_DEV dev, uint8_t pin,
+ VL53L0X_DeviceModes device_mode, VL53L0X_GpioFunctionality functionality,
+ VL53L0X_InterruptPolarity polarity);
+
+ /**
+ * @brief Start device measurement
+ *
+ * @details Started measurement will depend on device parameters set through
+ * @a VL53L0X_SetParameters()
+ * This is a non-blocking function.
+ * This function will change the VL53L0X_State from VL53L0X_STATE_IDLE to
+ * VL53L0X_STATE_RUNNING.
+ *
+ * @note This function Access to the device
+ *
+
+ * @param dev Device Handle
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_MODE_NOT_SUPPORTED This error occurs when
+ * DeviceMode programmed with @a VL53L0X_SetDeviceMode is not in the supported
+ * list:
+ * Supported mode are:
+ * VL53L0X_DEVICEMODE_SINGLE_RANGING,
+ * VL53L0X_DEVICEMODE_CONTINUOUS_RANGING,
+ * VL53L0X_DEVICEMODE_CONTINUOUS_TIMED_RANGING
+ * @return VL53L0X_ERROR_TIME_OUT Time out on start measurement
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_start_measurement(VL53L0X_DEV dev);
+
+ /**
+ * @brief Stop device measurement
+ *
+ * @details Will set the device in standby mode at end of current measurement\n
+ * Not necessary in single mode as device shall return automatically
+ * in standby mode at end of measurement.
+ * This function will change the VL53L0X_State from VL53L0X_STATE_RUNNING
+ * to VL53L0X_STATE_IDLE.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_stop_measurement(VL53L0X_DEV dev);
+
+ /**
+ * @brief Return device stop completion status
+ *
+ * @par Function Description
+ * Returns stop completiob status.
+ * User shall call this function after a stop command
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_stop_status Pointer to status variable to update
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_stop_completed_status(VL53L0X_DEV dev,
+ uint32_t *p_stop_status);
+
+ /**
+ * @brief Return Measurement Data Ready
+ *
+ * @par Function Description
+ * This function indicate that a measurement data is ready.
+ * This function check if interrupt mode is used then check is done accordingly.
+ * If perform function clear the interrupt, this function will not work,
+ * like in case of @a VL53L0X_PerformSingleRangingMeasurement().
+ * The previous function is blocking function, VL53L0X_GetMeasurementDataReady
+ * is used for non-blocking capture.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_measurement_data_ready Pointer to Measurement Data Ready.
+ * 0=data not ready, 1 = data ready
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_measurement_data_ready(VL53L0X_DEV dev,
+ uint8_t *p_measurement_data_ready);
+
+ /**
+ * @brief Retrieve the measurements from device for a given setup
+ *
+ * @par Function Description
+ * Get data from last successful Ranging measurement
+ * @warning USER should take care about @a VL53L0X_GetNumberOfROIZones()
+ * before get data.
+ * PAL will fill a NumberOfROIZones times the corresponding data
+ * structure used in the measurement function.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_ranging_measurement_data Pointer to the data structure to fill up.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_ranging_measurement_data(VL53L0X_DEV dev,
+ VL53L0X_RangingMeasurementData_t *p_ranging_measurement_data);
+
+ /**
+ * @brief Clear given system interrupt condition
+ *
+ * @par Function Description
+ * Clear given interrupt(s).
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param interrupt_mask Mask of interrupts to clear
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INTERRUPT_NOT_CLEARED Cannot clear interrupts
+ *
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_clear_interrupt_mask(VL53L0X_DEV dev, uint32_t interrupt_mask);
+
+ /**
+ * @brief Return device interrupt status
+ *
+ * @par Function Description
+ * Returns currently raised interrupts by the device.
+ * User shall be able to activate/deactivate interrupts through
+ * @a VL53L0X_SetGpioConfig()
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_interrupt_mask_status Pointer to status variable to update
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_interrupt_mask_status(VL53L0X_DEV dev,
+ uint32_t *p_interrupt_mask_status);
+
+ /**
+ * @brief Performs a single ranging measurement and retrieve the ranging
+ * measurement data
+ *
+ * @par Function Description
+ * This function will change the device mode to VL53L0X_DEVICEMODE_SINGLE_RANGING
+ * with @a VL53L0X_SetDeviceMode(),
+ * It performs measurement with @a VL53L0X_PerformSingleMeasurement()
+ * It get data from last successful Ranging measurement with
+ * @a VL53L0X_GetRangingMeasurementData.
+ * Finally it clear the interrupt with @a VL53L0X_ClearInterruptMask().
+ *
+ * @note This function Access to the device
+ *
+ * @note This function change the device mode to
+ * VL53L0X_DEVICEMODE_SINGLE_RANGING
+ *
+ * @param dev Device Handle
+ * @param p_ranging_measurement_data Pointer to the data structure to fill up.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_perform_single_ranging_measurement(VL53L0X_DEV dev,
+ VL53L0X_RangingMeasurementData_t *p_ranging_measurement_data);
+
+ /**
+ * @brief Single shot measurement.
+ *
+ * @par Function Description
+ * Perform simple measurement sequence (Start measure, Wait measure to end,
+ * and returns when measurement is done).
+ * Once function returns, user can get valid data by calling
+ * VL53L0X_GetRangingMeasurement or VL53L0X_GetHistogramMeasurement
+ * depending on defined measurement mode
+ * User should Clear the interrupt in case this are enabled by using the
+ * function VL53L0X_ClearInterruptMask().
+ *
+ * @warning This function is a blocking function
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_perform_single_measurement(VL53L0X_DEV dev);
+
+ /**
+ * @brief Read current status of the error register for the selected device
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_device_error_status Pointer to current error code of the device
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_device_error_status(VL53L0X_DEV dev,
+ VL53L0X_DeviceError *p_device_error_status);
+
+ /**
+ * @brief Human readable error string for a given Error Code
+ *
+ * @note This function doesn't access to the device
+ *
+ * @param error_code The error code as stored on ::VL53L0X_DeviceError
+ * @param p_device_error_string The error string corresponding to the ErrorCode
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_device_error_string(
+ VL53L0X_DeviceError error_code, char *p_device_error_string);
+
+ /**
+ * @brief Human readable Range Status string for a given RangeStatus
+ *
+ * @note This function doesn't access to the device
+ *
+ * @param range_status The RangeStatus code as stored on
+ * @a VL53L0X_RangingMeasurementData_t
+ * @param p_range_status_string The returned RangeStatus string.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_range_status_string(uint8_t range_status,
+ char *p_range_status_string);
+
+ VL53L0X_Error VL53L0X_get_total_signal_rate(VL53L0X_DEV dev,
+ VL53L0X_RangingMeasurementData_t *p_ranging_measurement_data,
+ FixPoint1616_t *p_total_signal_rate_mcps);
+
+ VL53L0X_Error VL53L0X_get_total_xtalk_rate(VL53L0X_DEV dev,
+ VL53L0X_RangingMeasurementData_t *p_ranging_measurement_data,
+ FixPoint1616_t *p_total_xtalk_rate_mcps);
+
+ /**
+ * @brief Get Ranging Timing Budget in microseconds
+ *
+ * @par Function Description
+ * Returns the programmed the maximum time allowed by the user to the
+ * device to run a full ranging sequence for the current mode
+ * (ranging, histogram, ASL ...)
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_measurement_timing_budget_micro_seconds Max measurement time in
+ * microseconds.
+ * Valid values are:
+ * >= 17000 microsecs when wraparound enabled
+ * >= 12000 microsecs when wraparound disabled
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_measurement_timing_budget_micro_seconds(VL53L0X_DEV dev,
+ uint32_t *p_measurement_timing_budget_micro_seconds);
+
+ /**
+ * @brief Set Ranging Timing Budget in microseconds
+ *
+ * @par Function Description
+ * Defines the maximum time allowed by the user to the device to run a
+ * full ranging sequence for the current mode (ranging, histogram, ASL ...)
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param measurement_timing_budget_micro_seconds Max measurement time in
+ * microseconds.
+ * Valid values are:
+ * >= 17000 microsecs when wraparound enabled
+ * >= 12000 microsecs when wraparound disabled
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS This error is returned if
+ MeasurementTimingBudgetMicroSeconds out of range
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_measurement_timing_budget_micro_seconds(VL53L0X_DEV dev,
+ uint32_t measurement_timing_budget_micro_seconds);
+
+ /**
+ * @brief Get specific limit check enable state
+ *
+ * @par Function Description
+ * This function get the enable state of a specific limit check.
+ * The limit check is identified with the LimitCheckId.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param limit_check_id Limit Check ID
+ * (0<= LimitCheckId < VL53L0X_GetNumberOfLimitCheck() ).
+ * @param p_limit_check_enable Pointer to the check limit enable
+ * value.
+ * if 1 the check limit
+ * corresponding to LimitCheckId is Enabled
+ * if 0 the check limit
+ * corresponding to LimitCheckId is disabled
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS This error is returned
+ * when LimitCheckId value is out of range.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_limit_check_enable(VL53L0X_DEV dev, uint16_t limit_check_id,
+ uint8_t *p_limit_check_enable);
+
+ /**
+ * @brief Enable/Disable a specific limit check
+ *
+ * @par Function Description
+ * This function Enable/Disable a specific limit check.
+ * The limit check is identified with the LimitCheckId.
+ *
+ * @note This function doesn't Access to the device
+ *
+ * @param dev Device Handle
+ * @param limit_check_id Limit Check ID
+ * (0<= LimitCheckId < VL53L0X_GetNumberOfLimitCheck() ).
+ * @param limit_check_enable if 1 the check limit
+ * corresponding to LimitCheckId is Enabled
+ * if 0 the check limit
+ * corresponding to LimitCheckId is disabled
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS This error is returned
+ * when LimitCheckId value is out of range.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_limit_check_enable(VL53L0X_DEV dev, uint16_t limit_check_id,
+ uint8_t limit_check_enable);
+
+ /**
+ * @brief Get a specific limit check value
+ *
+ * @par Function Description
+ * This function get a specific limit check value from device then it updates
+ * internal values and check enables.
+ * The limit check is identified with the LimitCheckId.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param limit_check_id Limit Check ID
+ * (0<= LimitCheckId < VL53L0X_GetNumberOfLimitCheck() ).
+ * @param p_limit_check_value Pointer to Limit
+ * check Value for a given LimitCheckId.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS This error is returned
+ * when LimitCheckId value is out of range.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_limit_check_value(VL53L0X_DEV dev, uint16_t limit_check_id,
+ FixPoint1616_t *p_limit_check_value);
+
+ /**
+ * @brief Set a specific limit check value
+ *
+ * @par Function Description
+ * This function set a specific limit check value.
+ * The limit check is identified with the LimitCheckId.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param limit_check_id Limit Check ID
+ * (0<= LimitCheckId < VL53L0X_GetNumberOfLimitCheck() ).
+ * @param limit_check_value Limit check Value for a given
+ * LimitCheckId
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS This error is returned when either
+ * LimitCheckId or LimitCheckValue value is out of range.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_limit_check_value(VL53L0X_DEV dev, uint16_t limit_check_id,
+ FixPoint1616_t limit_check_value);
+
+ /**
+ * @brief Get the current value of the signal used for the limit check
+ *
+ * @par Function Description
+ * This function get a the current value of the signal used for the limit check.
+ * To obtain the latest value you should run a ranging before.
+ * The value reported is linked to the limit check identified with the
+ * LimitCheckId.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param limit_check_id Limit Check ID
+ * (0<= LimitCheckId < VL53L0X_GetNumberOfLimitCheck() ).
+ * @param p_limit_check_current Pointer to current Value for a
+ * given LimitCheckId.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS This error is returned when
+ * LimitCheckId value is out of range.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_limit_check_current(VL53L0X_DEV dev, uint16_t limit_check_id,
+ FixPoint1616_t *p_limit_check_current);
+
+ /**
+ * @brief Return a the Status of the specified check limit
+ *
+ * @par Function Description
+ * This function returns the Status of the specified check limit.
+ * The value indicate if the check is fail or not.
+ * The limit check is identified with the LimitCheckId.
+ *
+ * @note This function doesn't Access to the device
+ *
+ * @param dev Device Handle
+ * @param limit_check_id Limit Check ID
+ (0<= LimitCheckId < VL53L0X_GetNumberOfLimitCheck() ).
+ * @param p_limit_check_status Pointer to the
+ Limit Check Status of the given check limit.
+ * LimitCheckStatus :
+ * 0 the check is not fail
+ * 1 the check if fail or not enabled
+ *
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS This error is
+ returned when LimitCheckId value is out of range.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_limit_check_status(VL53L0X_DEV dev,
+ uint16_t limit_check_id, uint8_t *p_limit_check_status);
+
+ /**
+ * Get continuous mode Inter-Measurement period in milliseconds
+ *
+ * @par Function Description
+ * When trying to set too short time return INVALID_PARAMS minimal value
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_inter_measurement_period_milli_seconds Pointer to programmed
+ * Inter-Measurement Period in milliseconds.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_inter_measurement_period_milli_seconds(VL53L0X_DEV dev,
+ uint32_t *p_inter_measurement_period_milli_seconds);
+
+ /**
+ * Program continuous mode Inter-Measurement period in milliseconds
+ *
+ * @par Function Description
+ * When trying to set too short time return INVALID_PARAMS minimal value
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param inter_measurement_period_milli_seconds Inter-Measurement Period in ms.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_inter_measurement_period_milli_seconds(
+ VL53L0X_DEV dev, uint32_t inter_measurement_period_milli_seconds);
+
+ /**
+ * @brief Set new device address
+ *
+ * After completion the device will answer to the new address programmed.
+ * This function should be called when several devices are used in parallel
+ * before start programming the sensor.
+ * When a single device us used, there is no need to call this function.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param device_address The new Device address
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_device_address(VL53L0X_DEV dev, uint8_t device_address);
+
+ /**
+ * @brief Do an hard reset or soft reset (depending on implementation) of the
+ * device \nAfter call of this function, device must be in same state as right
+ * after a power-up sequence.This function will change the VL53L0X_State to
+ * VL53L0X_STATE_POWERDOWN.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_reset_device(VL53L0X_DEV dev);
+
+ /**
+ * @brief Get setup of Wrap around Check
+ *
+ * @par Function Description
+ * This function get the wrapAround check enable parameters
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_wrap_around_check_enable Pointer to the Wrap around Check state
+ * 0=disabled or 1 = enabled
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_wrap_around_check_enable(VL53L0X_DEV dev,
+ uint8_t *p_wrap_around_check_enable);
+
+ /**
+ * @brief Enable (or disable) Wrap around Check
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param wrap_around_check_enable Wrap around Check to be set
+ * 0=disabled, other = enabled
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_wrap_around_check_enable(VL53L0X_DEV dev,
+ uint8_t wrap_around_check_enable);
+
+ /**
+ * @brief Gets the VCSEL pulse period.
+ *
+ * @par Function Description
+ * This function retrieves the VCSEL pulse period for the given period type.
+ *
+ * @note This function Accesses the device
+ *
+ * @param dev Device Handle
+ * @param vcsel_period_type VCSEL period identifier (pre-range|final).
+ * @param p_vcsel_pulse_period_pclk Pointer to VCSEL period value.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS Error VcselPeriodType parameter not
+ * supported.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_vcsel_pulse_period(VL53L0X_DEV dev,
+ VL53L0X_VcselPeriod vcsel_period_type, uint8_t *p_vcsel_pulse_period_pclk);
+
+ /**
+ * @brief Sets the VCSEL pulse period.
+ *
+ * @par Function Description
+ * This function retrieves the VCSEL pulse period for the given period type.
+ *
+ * @note This function Accesses the device
+ *
+ * @param dev Device Handle
+ * @param vcsel_period_type VCSEL period identifier (pre-range|final).
+ * @param vcsel_pulse_period VCSEL period value
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS Error VcselPeriodType parameter not
+ * supported.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_vcsel_pulse_period(VL53L0X_DEV dev,
+ VL53L0X_VcselPeriod vcsel_period_type, uint8_t vcsel_pulse_period);
+
+ /**
+ * @brief Set low and high Interrupt thresholds for a given mode
+ * (ranging, ALS, ...) for a given device
+ *
+ * @par Function Description
+ * Set low and high Interrupt thresholds for a given mode (ranging, ALS, ...)
+ * for a given device
+ *
+ * @note This function Access to the device
+ *
+ * @note DeviceMode is ignored for the current device
+ *
+ * @param dev Device Handle
+ * @param device_mode Device Mode for which change thresholds
+ * @param threshold_low Low threshold (mm, lux ..., depending on the mode)
+ * @param threshold_high High threshold (mm, lux ..., depending on the mode)
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_interrupt_thresholds(VL53L0X_DEV dev,
+ VL53L0X_DeviceModes device_mode, FixPoint1616_t threshold_low,
+ FixPoint1616_t threshold_high);
+
+ /**
+ * @brief Get high and low Interrupt thresholds for a given mode
+ * (ranging, ALS, ...) for a given device
+ *
+ * @par Function Description
+ * Get high and low Interrupt thresholds for a given mode (ranging, ALS, ...)
+ * for a given device
+ *
+ * @note This function Access to the device
+ *
+ * @note DeviceMode is ignored for the current device
+ *
+ * @param dev Device Handle
+ * @param device_mode Device Mode from which read thresholds
+ * @param p_threshold_low Low threshold (mm, lux ..., depending on the mode)
+ * @param p_threshold_high High threshold (mm, lux ..., depending on the mode)
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_interrupt_thresholds(VL53L0X_DEV dev,
+ VL53L0X_DeviceModes device_mode, FixPoint1616_t *p_threshold_low,
+ FixPoint1616_t *p_threshold_high);
+
+ /**
+ * @brief Reads the Device information for given Device
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_VL53L0X_device_info Pointer to current device info for a given
+ * Device
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_device_info(VL53L0X_DEV dev,
+ VL53L0X_DeviceInfo_t *p_VL53L0X_device_info);
+
+ /**
+ * @brief Gets the (on/off) state of all sequence steps.
+ *
+ * @par Function Description
+ * This function retrieves the state of all sequence step in the scheduler.
+ *
+ * @note This function Accesses the device
+ *
+ * @param dev Device Handle
+ * @param p_scheduler_sequence_steps Pointer to struct containing result.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_sequence_step_enables(VL53L0X_DEV dev,
+ VL53L0X_SchedulerSequenceSteps_t *p_scheduler_sequence_steps);
+
+ /**
+ * @brief Sets the (on/off) state of a requested sequence step.
+ *
+ * @par Function Description
+ * This function enables/disables a requested sequence step.
+ *
+ * @note This function Accesses the device
+ *
+ * @param dev Device Handle
+ * @param sequence_step_id Sequence step identifier.
+ * @param sequence_step_enabled Demanded state {0=Off,1=On}
+ * is enabled.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return VL53L0X_ERROR_INVALID_PARAMS Error SequenceStepId parameter not
+ * supported.
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_sequence_step_enable(VL53L0X_DEV dev,
+ VL53L0X_SequenceStepId sequence_step_id, uint8_t sequence_step_enabled);
+
+ /**
+ * @brief Gets the fraction enable parameter indicating the resolution of
+ * range measurements.
+ *
+ * @par Function Description
+ * Gets the fraction enable state, which translates to the resolution of
+ * range measurements as follows :Enabled:=0.25mm resolution,
+ * Not Enabled:=1mm resolution.
+ *
+ * @note This function Accesses the device
+ *
+ * @param dev Device Handle
+ * @param p_enabled Output Parameter reporting the fraction enable state.
+ *
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_fraction_enable(VL53L0X_DEV dev, uint8_t *p_enabled);
+
+ /**
+ * @brief Sets the resolution of range measurements.
+ * @par Function Description
+ * Set resolution of range measurements to either 0.25mm if
+ * fraction enabled or 1mm if not enabled.
+ *
+ * @note This function Accesses the device
+ *
+ * @param dev Device Handle
+ * @param enable Enable high resolution
+ *
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_set_range_fraction_enable(VL53L0X_DEV dev,
+ uint8_t enable);
+
+ /**
+ * @brief Return the VL53L0X PAL Implementation Version
+ *
+ * @note This function doesn't access to the device
+ *
+ * @param p_version Pointer to current PAL Implementation Version
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_version(VL53L0X_Version_t *p_version);
+
+ /**
+ * @brief Reads the Product Revision for a for given Device
+ * This function can be used to distinguish cut1.0 from cut1.1.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_product_revision_major Pointer to Product Revision Major
+ * for a given Device
+ * @param p_product_revision_minor Pointer to Product Revision Minor
+ * for a given Device
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_product_revision(VL53L0X_DEV dev,
+ uint8_t *p_product_revision_major, uint8_t *p_product_revision_minor);
+
+ /**
+ * @brief Retrieve current device parameters
+ * @par Function Description
+ * Get actual parameters of the device
+ * @li Then start ranging operation.
+ *
+ * @note This function Access to the device
+ *
+ * @param dev Device Handle
+ * @param p_device_parameters Pointer to store current device parameters.
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_device_parameters(VL53L0X_DEV dev,
+ VL53L0X_DeviceParameters_t *p_device_parameters);
+
+ /**
+ * @brief Human readable error string for current PAL error status
+ *
+ * @note This function doesn't access to the device
+ *
+ * @param pal_error_code The error code as stored on @a VL53L0X_Error
+ * @param p_pal_error_string The error string corresponding to the
+ * PalErrorCode
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_pal_error_string(VL53L0X_Error pal_error_code,
+ char *p_pal_error_string);
+
+ /**
+ * @brief Return the PAL Specification Version used for the current
+ * implementation.
+ *
+ * @note This function doesn't access to the device
+ *
+ * @param p_pal_spec_version Pointer to current PAL Specification Version
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_pal_spec_version(
+ VL53L0X_Version_t *p_pal_spec_version);
+
+ /**
+ * @brief Reads the internal state of the PAL for a given Device
+ *
+ * @note This function doesn't access to the device
+ *
+ * @param dev Device Handle
+ * @param p_pal_state Pointer to current state of the PAL for a
+ * given Device
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_pal_state(VL53L0X_DEV dev,
+ VL53L0X_State *p_pal_state);
+
+ /**
+ * @brief Human readable PAL State string
+ *
+ * @note This function doesn't access to the device
+ *
+ * @param pal_state_code The State code as stored on @a VL53L0X_State
+ * @param p_pal_state_string The State string corresponding to the
+ * PalStateCode
+ * @return VL53L0X_ERROR_NONE Success
+ * @return "Other error code" See ::VL53L0X_Error
+ */
+ VL53L0X_Error VL53L0X_get_pal_state_string(VL53L0X_State pal_state_code,
+ char *p_pal_state_string);
+
+ /*** End High level API ***/
+