Diff: FT800_Display.h

Revision:

0:b699e59d925b

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/FT800_Display.h	Thu Dec 03 21:59:15 2020 +0000
@@ -0,0 +1,50 @@
+/* mbed Library for FTDI FT800 */
+ 
+#ifndef FT800_DISPLAY_H
+#define FT800_DISPLAY_H
+
+#define GPU_FREQ            48000000ULL     // FT800 frequency 
+#define DISP_FPS            60              // frame rate
+
+//------------------------------------------------------------------------------
+//DISPLAY TIMING         480 x 272   320 x 240
+//------------------------------------------------------------------------------
+#define DISP_WIDTH          480     // 320  // Horizontal Size
+#define DISP_HSYNC0         0       // 0    // Start of HSYNC (falling edge)
+#define DISP_HSYNC1         41      // 10   // End of HSYNC (rising edge)
+#define DISP_HFP            25
+#define DISP_HSLEN          2
+
+#define DISP_HEIGHT         272     // 240  // Vertical Size
+#define DISP_VSYNC0         0       // 0    // Start of VSYNC (falling edge)
+#define DISP_VSYNC1         10      // 2    // End of VSYNC (rising edge)
+#define DISP_VFP            8
+#define DISP_VSLEN          2
+
+#define DISP_PCLK_POL       1       // 0    // Pixel Clock Polarity
+#define DISP_SWIZZLE        0               // B[7:2] G[7:2] R[7:2] - arrangement of output RGB pins
+
+#define DISP_HCYCLE         548     // 408  // (DISP_WIDTH + DISP_HSYNC1 + DISP_HFP + DISP_HSLEN) Total number of clocks per line
+#define DISP_VCYCLE         292     // 263  // (DISP_HEIGHT+ DISP_VSYNC1 + DISP_VFP + DISP_VSLEN) Total number of lines per screen
+#define DISP_PCLK           5       // 8    // (GPU_FREQ / DISP_VCYCLE / DISP_HCYCLE /(DISP_FPS-1)) Set Pixel Clock Frequenc
+
+#define DISP_PWM_HZ         250     // 250  // Set backlight PWM frequency in Hz
+#define DISP_PWM_DUTY       128     // 128  // Set backlight duty cycle (brightness), 0 = off, 0x80 = full brightness
+
+//------------------------------------------------------------------------------
+//TOUCH SCREEN
+//------------------------------------------------------------------------------
+#define TOUCH_SENSITIVITY   1500    // 0x0000-0xFFFF (highest sensitivity)
+#define TOUCH_MODE          3       // 0-off, 1- single mode, 2-frame mode, 3-continuous mode 
+#define TOUCH_ADC_MODE      1       // 0-Single Ended mode,  1-Differential Mode
+#define TOUCH_CHARGE        6000    // touch-screen charge time, in the unit of 6 clocks
+#define TOUCH_SETTLE        3       // touch screen settle time in the unit of 6 clocks
+#define TOUCH_OVERSAMPLE    7       // 1-15, touch screen oversample factor. The higher value -> more accuracy & more power consumption 
+
+//------------------------------------------------------------------------------
+//GPIO PINS
+//------------------------------------------------------------------------------
+#define GPIO_DIR            0x80    // GPIO7-GPIO0, 1=output, 0=input
+#define GPIO_SET            0x80    // GPIO7-GPIO0, 1="HI", 0="LO"
+
+#endif
\ No newline at end of file