Small Internet Protocol Stack using a standard serial port.

Dependencies:   mbed

PPP-Blinky - TCP/IP Networking Over a Serial Port

Note: The source code is at the bottom of this page.

/media/uploads/nixnax/blinky-connected.gif
A Windows desktop showing PPP-Blinky in the network connections list.

Describe PPP-Blinky in Three Sentences

PPP-Blinky is a tiny library that enables Internet protocols (IPv4) to any mbed target hardware by using only a serial port.

The code runs on processors with as little as 8k RAM, for example the Nucleo-L053R8 board.

PPP-Blinky uses the industry-standard PPP (Point-to-Point) Protocol and a tiny "stateless" TCP/IP stack.

No Ethernet Port Required

No ethernet port is required - PPP-Blinky uses a serial port to send IP packets to your PC.

PPP-Blinky emulates a standard dial-up modem and therefore connects to Windows, Linux or Adroid machines.

The code runs on most ARM mbed platforms such as the LPC11U24 shown in the picture below:

/media/uploads/nixnax/blinky-to-laptop1.jpg mbed LPC11u24 acting as a webserver to a Windows laptop.

Webserver

The Webserver and WebSocket functions are ideal for building browser-based GUIs on mbed-enabled hardware.

PPP-Blinky's HTTP webserver works with most web clients such as Internet Explorer, Mozilla Firefox, Google Chrome, Safari, Curl, wget and Lynx as well as Microsoft Powershell Invoke-Webrequest command.

In the image below Firefox web browser displays the main web page embedded into PPP-Blinky's code:

/media/uploads/nixnax/ppp-blinky-firefox.jpg Firefox web browser displays a web page embedded into PPP-Blinky's code

WebSocket Service

WebSocket is the most popular protocol standard for real-time bidirectional TCP/IP communication between clients and servers.
In the image below a small Internet Explorer script has connected to PPP-Blinky's WebSocket Service.
A websocket message was then sent by the browser and was echoed back by the WebSocket, triggering the onmessage event in the script.
The WebSocket service enables bidirectional real-time interaction between PPP-Blinky and any element in the browser DOM via JavaScript.
If you already have PPP-Blinky up and running you can test your WebSocket service using this: http://jsfiddle.net/d26cyuh2/112/embedded/result
Websockets are ideal for building browser-based GUIs for mbed hardware.

/media/uploads/nixnax/ppp-blinky-websocke-2.gif

Trying PPP-Blinky on your mbed board

You will need an mbed-enabled hardware board: https://developer.mbed.org/platforms/

Establish a serial port connection between your host PC and your mbed board. The easiest way is to use mbed hardware with a USB serial debug port. I've tried the ST-Micro Nucleo-L476RG, Nucleo-L152RE, Nucleo-F401RE, Nucleo-L432KC, Nucleo-L053R8, mbed-LPC11U24 and mbed-LPC1768 boards and they all work out of the box. Use the mbed online compiler to compile the software for your target board. Save the compiled binary to your hardware.

Before establishing a network connection, you can verify the operation of the code by opening a terminal program such as Tera Term, and setting the baud rate of the COM port on your mbed board to 115200 baud. LED1 should toggle for every two 0x7E (~) (i.e. tilde) characters you type, as 0x7E is the PPP frame start/end marker. Don't forget to close the port when your'e done testing, or else Windows Dial-up Networking will report that the COM port is in use by another program when you try to connect.

Once you are certain that the serial port and firmware is working, proceed to creating a new network connection on your PC -see below.

Creating a Dial-up Connection in Windows

/media/uploads/nixnax/modem.jpg

Setting up Dial-Up Networking (DUN) on your Windows 7 or 8 PC is essentially a two-step process: First, you create a new modem device, because PPP-blinky partially emulates a standard Windows serial port modem device. Second, you create a new Internet connection (in practice, a new network adapter) which is associated with your new "modem".

Step-by-step description of how to configure Windows for PPP-Blinky here:

/users/nixnax/code/PPP-Blinky/wiki/Configuring-Windows-Dial-Up-Networking

There is also a screen on how to set up Linux dial-up networking near the bottom of this page.

Connecting to PPP-Blinky from your PC

Once Windows networking is configured you can establish a dial-up connection to your mbed board over the USB virtual com port.

The IP address you manually assigned to the new dial-up network adapter (172.10.10.1) functions as a gateway to any valid IP address on that subnet. In the screen capture below, I'm sending pings from the Windows 8 command line to my ST-Micro Nucleo-L476RG board over the USB virtual serial Port. I'm also using a second serial port and Tera Term to capture the debug output from a second serial port on the hardware. The optional debug output from the board prints out the IP source and destination address and the first few bytes of the data payload. Note that the source is the adapter IP address, (172.10.10.1 in this case) and the destination is some other address on that subnet - all packets to the subnet are sent to our mbed hardware. For example, you could also ping 172.10.10.123 or, if your PPP-Blinky is running, simply click on this link: http://172.10.10.123

/media/uploads/nixnax/ping-cap-3.gif

One Million Pings!

In the image below the ICMP ("ping") echo reply service was tested by sending one million pings to ppp-Blinky. This took over two hours.
The ping tool used on the Windows 8 PC was psping.exe from PsTools by Mark Russinovich - http://bit.ly/PingFast
The average reply time for a short ping (1 byte of payload data) was 11 milliseconds at 115200 baud on the $10 Nucleo-L053R8 board - barely enough time for 130 bytes to be sent over the port!

/media/uploads/nixnax/ppp-blinky-ping-results.jpg

Monitoring PPP-Blinky Packets

The image below is from a Microsoft Network Monitor 3.4 capture session.

Responses from PPP-Blinky are shown in blue.

Frame 2 - Internet Explorer at IP 172.10.10.1 (the Dial-Up Adapter IP) requests a TCP connection by sending an S (SYN) flag.
Frame 3 - PPP-Blinky at IP 172.10.10.2 responds with an ACK in frame 3. One direction of the link is now established.
Frame 4 - The PC acknowledges the SYN sent by PPP-Blinky in frame 3. The TCP link is now fully established.
Frame 5 - The browser "pushes" (P flag is set) an HTTP GET request to PPP-Blinky.
Frame 6 - PPP-Blinky responds with a standard HTTP response "pushes" (P flag set) back a small web page. It also sets the A (ACK) flag to acknowledge the message sent in frame 6.
Frame 7 - The PC acknowledges reception of the HTTP payload.
Frame 8 - The PC starts to shut down the TCP connection by sending a FIN flag.
Frame 9 - PPP-Blinky acknowledges the FIN request - the connection is now closed in one direction. It also sets a FIN flag in the response to request closure of the opposite direction of the connection.
Frame 10 - The PC acknowledges the FIN request. The closing of the TCP connection is now confirmed in both directions.

/media/uploads/nixnax/ms-network-monitor-http-get-1.gif

Debug Output

PPP-Blinky can output handy debug information to an optional second serial port.
The image below shows the debug output (Ident, Source, Destination, TCP Flags) for a complete HTTP conversation.
The PC messages are displayed in black. PPP-Blinky messages are blue.
Notice how PPP-blinky automatically inserts a blank line after each full HTTP conversation.

/media/uploads/nixnax/tcp-data-3.gif

Creating a Dial-Up Connection in Linux

The screen below shows the required pppd command to connect to PPP-Blinky from a Linux machine. This was much simpler than Windows! The USB serial port of the mbed LPC1768 board registered as /dev/ttyACM0 on my Linux box. Do a websearch on pppd if you want to learn more about pppd, the Linux PPP handler. Near the bottom of the screen below, two webpages are fetched (/ and /y) by using the curl command on the command line. Gnome Webkit and Firefox work fine, too. Also try echo GET / HTTP/1.1 | nc 172.10.10.2 which uses netcat, the "Swiss army knife" of networking tools. PPP-Blinky was also tested with ApacheBench, the Apache server benchmark software. After 100000 fetches, the mean page fetch rate was reported as 6 page fetches per second for a small page.

/media/uploads/nixnax/pppd-screen.png

Caveats

PPP Blinky is an extremely sparse implementation (1.5k lines) of HTTP,WebSocket,TCP, UDP, ICMP, IPCP and LCP over PPP, requiring around 8kB of RAM. The minimum functionality required to establish connectivity is implemented. These are often acceptable tradeoffs for embedded projects as well as a handy tool to learn the practical details of everyday networking implementations.

Revision:
12:db0dc91f0231
Parent:
11:f58998c24f0b
Child:
13:d882b8a042b4
--- a/main.cpp	Sat Dec 31 14:35:27 2016 +0000
+++ b/main.cpp	Sun Jan 01 01:20:33 2017 +0000
@@ -1,5 +1,7 @@
 #include "mbed.h"
 
+// Copyright 2016 Nicolas Nackel. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+
 // Proof-of-concept for TCP/IP using Windows 7/8/10 Dial Up Networking over MBED USB Virtual COM Port
 
 // Toggles LED1 every time the PC sends an IP packet over the PPP link
@@ -83,7 +85,7 @@
         if (unstuff==0) {
             if (rxbuf[i]==0x7d) unstuff=1; 
             else { *dest++ = rxbuf[i]; ppp.pkt.len++; crcDo(rxbuf[i]);}
-        } else {
+        } else { // unstuff
             *dest++ = rxbuf[i]^0x20; ppp.pkt.len++; crcDo((int)rxbuf[i]^0x20);
             unstuff=0;
         }
@@ -92,10 +94,10 @@
     if (ppp.pkt.crc == 0xf0b8) { // check for good CRC
         void determinePacketType(); // declare early
         determinePacketType();
-    } else {
-         xx.printf("CRC was %x \n",ppp.pkt.crc);
+    } else { // crc error
+         xx.printf("CRC is %x Len is %d\n",ppp.pkt.crc,ppp.pkt.len);
          for(int i=0;i<ppp.pkt.len;i++)xx.printf("%02x ", ppp.pkt.buf[i]);
-         xx.printf("\nLen = %d\n", ppp.pkt.len);
+         xx.printf("\n");
     }
 }
 
@@ -104,22 +106,17 @@
     xx.printf(" C %02x %02x L=%d\n", ppp.pkt.crc&0xff, (ppp.pkt.crc>>8)&0xff, ppp.pkt.len);
 }
 
-void generalFrame() {
-    debug("== General Frame ==\n");
-    dumpFrame();
-}    
-
 void sendFrame(){
     int crc = crcBuf(ppp.pkt.buf, ppp.pkt.len-2); // get crc
-    ppp.pkt.buf[ ppp.pkt.len-2 ] = (~crc>>0); // fcs lo
-    ppp.pkt.buf[ ppp.pkt.len-1 ] = (~crc>>8); // fcs hi
-    pc.putc(0x7e); // frame flag
+    ppp.pkt.buf[ ppp.pkt.len-2 ] = (~crc>>0); // fcs lo (crc)
+    ppp.pkt.buf[ ppp.pkt.len-1 ] = (~crc>>8); // fcs hi (crc)
+    pc.putc(0x7e); // frame start flag
     for(int i=0;i<ppp.pkt.len;i++) {
         //xx.printf( "%2x ", ppp.pkt.buf[i]);
         unsigned int cc = (unsigned int)ppp.pkt.buf[i];
         if (cc>32) pc.putc(cc); else {pc.putc(0x7d); pc.putc(cc+32);}
     } 
-    pc.putc(0x7e); // frame flag
+    pc.putc(0x7e); // frame end flag
 }
 
 void ipRequestHandler(){
@@ -132,9 +129,9 @@
         debug("Ack\n");
         ppp.pkt.buf[4]=2; // ack the minimum
         sendFrame(); // acknowledge
+        debug("IPCP Ask\n"); 
         // send our own request now
-        debug("IPCP Ask\n");
-        ppp.pkt.buf[4]=1; // request the minimum
+        ppp.pkt.buf[4]=1; // request no options
         ppp.pkt.buf[5]++; // next sequence
         sendFrame(); // this is our request
     }
@@ -159,17 +156,32 @@
 }    
 
 void UDPpacket() {
-    int idx = 4+((ppp.pkt.buf[4]&0xf)*4);
-    int srcPort =  (ppp.pkt.buf[idx+0]<<8)|ppp.pkt.buf[idx+1];
-    int dstPort = (ppp.pkt.buf[idx+2]<<8)|ppp.pkt.buf[idx+3];
-    xx.printf("UDP %d.%d.%d.%d:%d ", ppp.pkt.buf[16],ppp.pkt.buf[17],ppp.pkt.buf[18],ppp.pkt.buf[19],srcPort);
-    xx.printf("%d.%d.%d.%d:%d\n",    ppp.pkt.buf[20],ppp.pkt.buf[21],ppp.pkt.buf[22],ppp.pkt.buf[23],dstPort);
-}    
-
+    char * udpPkt = ppp.pkt.buf+4; // udp packet start
+    //char * pktLen = udpPkt+2; // total packet length
+    int headerSize = (( udpPkt[0]&0xf)*4);
+    char * udpBlock = udpPkt + headerSize; // udp info start 
+    char * udpSrc = udpBlock; // source port
+    char * udpDst = udpBlock+2; // destination port
+    char * udpLen = udpBlock+4; // udp data length
+    char * udpInf = udpBlock+8; // actual start of info
+    //char * udpSum = udpBlock+6; // udp checksum
+    //int packetLength = (pktLen[0]<<8) | pktLen[1]; // udp total packet length
+    int srcPort = (udpSrc[0]<<8) | udpSrc[1];
+    int dstPort = (udpDst[0]<<8) | udpDst[1];
+    char * srcIP = udpPkt+12; // udp src addr
+    char * dstIP = udpPkt+16; // udp dst addr
+    #define UDP_HEADER_SIZE 8
+    int udpLength = ((udpLen[0]<<8) | udpLen[1]) - UDP_HEADER_SIZE; // size of the actual udp data
+    xx.printf("UDP %d.%d.%d.%d:%d ", srcIP[0],srcIP[1],srcIP[2],srcIP[3],srcPort);
+    xx.printf("%d.%d.%d.%d:%d ",    dstIP[1],dstIP[1],dstIP[1],dstIP[1],dstPort);
+    xx.printf("Len %d ", udpLength);
+    int printSize = udpLength > 20 ? 20 : udpLength;
+    for (int i=0; i<printSize; i++) { xx.putc( udpInf[i]); } // printf first 20 characters of the data
+    xx.printf("\n");
+}
 
 int dataCheckSum(char * ptr, int len) {
     int sum=0;
-
     for (int i=0;i<len/2;i++) {
         int hi = *ptr; ptr++;
         int lo = *ptr; ptr++;
@@ -177,11 +189,9 @@
         sum = sum + val;
     }
     sum = sum + (sum>>16);
-    sum = ~sum;
-    return sum;
+    return ~sum;
 }    
 
-
 void headerCheckSum() {
     int len =(ppp.pkt.buf[4]&0xf)*4; // length of header in bytes
     char * ptr = ppp.pkt.buf+4; // start of ip packet
@@ -197,34 +207,40 @@
     sum = ~sum;
     ppp.pkt.buf[14]= (sum>>8);
     ppp.pkt.buf[15]= (sum   );
-    
-    
-    
 }    
 
 void ICMPpacket() { // internet control message protocol
- 
-    int headerSize = ((ppp.pkt.buf[4]&0xf)*4);
-    int idx = headerSize + 4;
-    xx.printf("ICMP type=%d \n", ppp.pkt.buf[idx]); 
-    if ( ppp.pkt.buf[idx] == 8 ) { 
-        ppp.pkt.buf[12] = ppp.pkt.buf[12]-1; // TTL decrement
+    char * ipPkt = ppp.pkt.buf+4; // ip packet start
+    char * pktLen = ipPkt+2;
+    int packetLength = (pktLen[0]<<8) | pktLen[1]; // icmp packet length
+    int headerSize = (( ipPkt[0]&0xf)*4);
+    char * icmpType = ipPkt + headerSize; // icmp data start
+    char * icmpData = icmpType; // icmp packet type
+    char * icmpSum = icmpData+2; // icmp checksum
+    #define ICMP_TYPE_PING_REQUEST 8
+    if ( icmpType[0] == ICMP_TYPE_PING_REQUEST ) { 
+        xx.printf("ICMP PING\n");
+        char * ipTTL = ipPkt+8; // time to live
+        ipTTL[0]--; // decrement time to live
+        char * srcAdr = ipPkt+12;
+        char * dstAdr = ipPkt+16;
         char src[4]; char dst[4];
-        memcpy(src, ppp.pkt.buf+16,4);
-        memcpy(dst, ppp.pkt.buf+20,4);
-        memcpy(ppp.pkt.buf+16,dst,4);
-        memcpy(ppp.pkt.buf+20,src,4); // swap src & dest ip
-        ppp.pkt.buf[15]=0; 
-        ppp.pkt.buf[14]=0;
-        headerCheckSum();  // calc ip header checksum
-
-
-        int packetLength = (ppp.pkt.buf[6]<<8)|ppp.pkt.buf[7];
-        int dataLength = packetLength - headerSize;
-        ppp.pkt.buf[idx]=0; ppp.pkt.buf[idx+2]=0; ppp.pkt.buf[idx+3]=0;
-        int sum = dataCheckSum( ppp.pkt.buf+idx, dataLength); // calc icmp data checksum
-        ppp.pkt.buf[idx+2]=(sum>>8); ppp.pkt.buf[idx+3]=(sum   );
+        memcpy(src, srcAdr,4);
+        memcpy(dst, dstAdr,4);
+        memcpy(srcAdr, dst,4);
+        memcpy(dstAdr, src,4); // swap src & dest ip
+        char * chkSum = ipPkt+10;
+        chkSum[0]=0; chkSum[1]=0;
+        headerCheckSum();  // new ip header checksum
+        #define ICMP_TYPE_ECHO_REPLY 0
+        icmpType[0]=ICMP_TYPE_ECHO_REPLY; // icmp echo replay
+        icmpSum[0]=0; icmpSum[1]=0; // zero the checksum for recalculation
+        int dataLength = packetLength - headerSize; // length of ICMP data portion
+        int sum = dataCheckSum( icmpData, dataLength); // new data portion checksum
+        icmpSum[0]=sum>>8; icmpSum[1]=sum; // new checksum for ICMP data portion
         sendFrame();
+    } else {
+        xx.printf("ICMP type=%d \n", icmpType[0]); 
     }
 }
 
@@ -245,7 +261,7 @@
 }    
 
 void otherProtocol() {
-    debug("Other protocol");
+    debug("Other IP protocol");
 }
 
 void IPframe() {
@@ -260,7 +276,6 @@
     //xx.printf("IP frame proto %3d len %4d %d.%d.%d.%d  %d.%d.%d.%d\n", ppp.pkt.buf[13],(ppp.pkt.buf[6]<<8)+ppp.pkt.buf[7],ppp.pkt.buf[16],ppp.pkt.buf[17],ppp.pkt.buf[18],ppp.pkt.buf[19],ppp.pkt.buf[20],ppp.pkt.buf[21],ppp.pkt.buf[22],ppp.pkt.buf[23] );
 }    
 
-
 void LCPconfReq() {
     debug("LCP Config ");
     if (ppp.pkt.buf[7] != 4) {
@@ -283,28 +298,28 @@
 
 void LCPend(){
      debug("LCP End\n");
-     ppp.online=0; 
+     ppp.online=0; // start hunting for connect string again
      ppp.pkt.buf[4]=6;
-     sendFrame();
+     sendFrame(); // acknowledge
 }
 
 void LCPother(){
      debug("LCP Other\n");
-     generalFrame();
+     dumpFrame();
 }
 
 void LCPframe(){
      int code = ppp.pkt.buf[4];
      switch (code) {
-         case 1: LCPconfReq(); break;
-         case 2: LCPconfAck(); break;
-         case 5: LCPend(); break;
-         default: LCPother();
+         case 1:    LCPconfReq(); break; // config request
+         case 2:    LCPconfAck(); break; // config ack
+         case 5:    LCPend();     break; // end connection
+         default:   LCPother();
      }
 }
 
-void xx21frame() {
-    debug("Unknown frame type ff 03 xx 21\n");
+void discardedFrame() {
+    xx.printf("Dropping frame %02x %02x %02x %02x\n", ppp.pkt.buf[0],ppp.pkt.buf[1],ppp.pkt.buf[2],ppp.pkt.buf[3] );
 }
 
 void determinePacketType() {
@@ -313,10 +328,10 @@
     if ( ppp.pkt.buf[3] != 0x21 ) {debug("byte2 != 21\n"); return;}
     int packetType = ppp.pkt.buf[2];
     switch (packetType) {
-        case 0xc0: LCPframe(); break; 
-        case 0x80: IPCPframe(); break;
-        case 0x00: IPframe(); break;
-        default: xx21frame(); break;
+        case 0xc0:  LCPframe();     break;  // link control
+        case 0x80:  IPCPframe();    break;  // IP control
+        case 0x00:  IPframe();      break;  // IP itself
+        default:    discardedFrame();
     }
 }    
 
@@ -334,7 +349,7 @@
 
 int main()
 {
-    pc.baud(9600);
+    pc.baud(115200);
     xx.baud(115200); 
     xx.puts("\x1b[2J\x1b[HReady\n"); // VT100 code for clear screen & home