File content as of revision 12:f0980f7a75ae:

/* mbed Library for FTDI FT813  Enbedded Video Engine "EVE"
 * based on Original Code Sample from FTDI
 * ported to mbed by Peter Drescher, DC2PD 2014
 * Released under the MIT License: http://mbed.org/license/mit 
 * 19.09.14 changed to shorter function names  
 * FTDI was using very long names. 
 * Ft_App_Flush_Co_Buffer -> Flush_Co_Buffer ...  */

#include "FT_Platform.h"
#include "mbed.h"
#include "FT_LCD_Type.h"
//Serial pc(USBTX, USBRX);
//Serial pc(SERIAL_TX,SERIAL_RX,115200);
#define SPI_SPEED_START 10000000
#define SPI_SPEED_AFTER 27000000

FT813::FT813(PinName mosi,
            PinName miso,
            PinName sck,
            PinName ss,
            PinName intr,
            PinName pd)
:
_spi(mosi, miso, sck),
_ss(ss),
_pd(pd),
_f800_isr(InterruptIn(intr))
{
    _spi.format(8, 0);                  // 8 bit spi mode 0
    _spi.frequency(SPI_SPEED_START);          // start with 10 Mhz SPI clock
    _ss = 1;                           // cs high
    _pd = 1;                           // PD high
    _IsOn=Bootup();
    _address = 0;
    _bitmap_count = 0;
    _bitmapCount = 0;
    _bitmapAddress = 0;
}


ft_bool_t FT813::Bootup(void)
{
   //printf("Bootup() entered\r\n");//temp
    Open();

    return BootupConfig();   
}

ft_bool_t FT813::IsOn(void)
{
    return FT813::_IsOn;
}

char FT813::BootupConfig(void)
{
    ft_uint8_t chipid;
    /* Do a power cycle for safer side */
    Powercycle(FT_TRUE);
    /*
    7/8/16: Curt added the sleep delay below...
    */
//  Sleep(30);
    
    /* Set the clk to external clock */
    HostCommand(FT_GPU_INTERNAL_OSC);
    Sleep(10);
    
    /* Access address 0 to wake up the FT813 */
    HostCommand(FT_GPU_ACTIVE_M);
    Sleep(500);

    /* Switch PLL output to 48MHz */
    HostCommand(FT_GPU_PLL_48M);
    Sleep(10);

    /* Do a core reset for safer side */
    HostCommand(FT_GPU_CORE_RESET);
    Sleep(500);
    //Read Register ID to check if FT813 is ready.
    chipid = Rd8(REG_ID);
  //chipid = Rd8(0x0C0000);
    //pc.printf("ID1: 0x%08X\n", chipid);//temp
    
    //Если дисплей не отвечает то прервать инициализацию
    char sec=0;
    while(chipid != 0x7C) //раскомментить как заработает    
    {
        wait_ms(100);
        sec++;
        if (sec>5)
            {
            printf("ERR!: Display is not connected\r\n");
            return 0;
            } 
        }
    //tmp
    //printf("ID2: 0x%08X\n", chipid);//tmp

    // Speed up
//    _spi.frequency(50000000);           // 30 Mhz SPI clock DC
    _spi.frequency(SPI_SPEED_AFTER);           // 20 Mhz SPI clock DC
//    _spi.frequency(12000000);           // 12 Mhz SPI clock
    /* Configuration of LCD display */
    DispHCycle = my_DispHCycle;
    Wr16(REG_HCYCLE, DispHCycle);
    DispHOffset = my_DispHOffset;
    Wr16(REG_HOFFSET, DispHOffset);
    DispWidth = my_DispWidth;
    Wr16(REG_HSIZE, DispWidth);
    DispHSync0 = my_DispHSync0;
    Wr16(REG_HSYNC0, DispHSync0);
    DispHSync1 = my_DispHSync1;
    Wr16(REG_HSYNC1, DispHSync1);
    DispVCycle = my_DispVCycle;
    Wr16(REG_VCYCLE, DispVCycle);
    DispVOffset = my_DispVOffset;
    Wr16(REG_VOFFSET, DispVOffset);
    DispHeight = my_DispHeight;
    Wr16(REG_VSIZE, DispHeight);
    DispVSync0 = my_DispVSync0;
    Wr16(REG_VSYNC0, DispVSync0);
    DispVSync1 = my_DispVSync1;
    Wr16(REG_VSYNC1, DispVSync1);
    DispSwizzle = my_DispSwizzle;
    Wr8(REG_SWIZZLE, DispSwizzle);
    DispPCLKPol = my_DispPCLKPol;
    Wr8(REG_PCLK_POL, DispPCLKPol);
    Wr8(REG_CSPREAD, 1); //поменяно для Riverdi 0 на 1
    DispPCLK = my_DispPCLK;
    Wr8(REG_PCLK, DispPCLK);    // After this display is visible on the LCD

    Wr16(REG_PWM_HZ, 10000);
//#ifdef Inv_Backlite               // turn on backlite
//    Wr16(REG_PWM_DUTY, 0);
//#else
    Wr16(REG_PWM_DUTY, 255); // Brightness 127
//#endif
    Wr8(REG_GPIO_DIR, 0x82);  //| Rd8(REG_GPIO_DIR));
    Wr8(REG_GPIO, 0x080);     //| Rd8(REG_GPIO));

    Wr32(RAM_DL, CLEAR(1, 1, 1));
    Wr32(RAM_DL+4, DISPLAY());
    Wr32(REG_DLSWAP, 1);

    Wr16(REG_PCLK, DispPCLK);

    /* Touch configuration - configure the resistance value to 1200 */
    /* This value is specific to customer requirement and derived by experiment */
//    Wr16(REG_TOUCH_RZTHRESH,2400);
    Wr16(REG_TOUCH_RZTHRESH, 1800); //поменяно с 0xFFFF на 1800
    return 1; //дисплей включен и настроен
}

/* API to initialize the SPI interface */
ft_bool_t FT813::Init()
{
    // This is done in the constructor
    return 1;
}

ft_bool_t FT813::Open()
{
    cmd_fifo_wp = dl_buff_wp = 0;
    status = OPENED;
    return 1;
}

ft_void_t FT813::Close()
{
    status = CLOSED;
}

ft_void_t FT813::DeInit()
{
}

/*The APIs for reading/writing transfer continuously only with small buffer system*/
ft_void_t FT813::StartTransfer(FT_GPU_TRANSFERDIR_T rw, ft_uint32_t addr)
{
    if (FT_GPU_READ == rw) {
        _ss = 0;       // cs low
        _spi.write(addr >> 16);
        _spi.write(addr >> 8);
        _spi.write(addr & 0xff);
        _spi.write(0); //Dummy Read Byte
        status = READING;
    } else {
        _ss = 0;       // cs low
        _spi.write(0x80 | (addr >> 16));
        _spi.write(addr >> 8);
        _spi.write(addr & 0xff);
        status = WRITING;
    }
}


/*The APIs for writing transfer continuously only*/
ft_void_t FT813::StartCmdTransfer(FT_GPU_TRANSFERDIR_T rw, ft_uint16_t count)
{
    StartTransfer(rw, cmd_fifo_wp + RAM_CMD);
}

ft_uint8_t FT813::TransferString(const ft_char8_t *string)
{
    ft_uint16_t length = strlen(string);
    while(length --) {
       Transfer8(*string);
       string++;
    }
    //Append one null as ending flag
    Transfer8(0);
    return(1);
}


ft_uint8_t FT813::Transfer8(ft_uint8_t value)
{
        return _spi.write(value);
}


ft_uint16_t FT813::Transfer16(ft_uint16_t value)
{
    ft_uint16_t retVal = 0;

        if (status == WRITING) {
        Transfer8(value & 0xFF);//LSB first
        Transfer8((value >> 8) & 0xFF);
    } else {
        retVal = Transfer8(0);
        retVal |= (ft_uint16_t)Transfer8(0) << 8;
    }

    return retVal;
}

ft_uint32_t FT813::Transfer32(ft_uint32_t value)
{
    ft_uint32_t retVal = 0;
    if (status == WRITING) {
        Transfer16(value & 0xFFFF);//LSB first
        Transfer16((value >> 16) & 0xFFFF);
    } else {
        retVal = Transfer16(0);
        retVal |= (ft_uint32_t)Transfer16(0) << 16;
    }
    return retVal;
}

ft_void_t FT813::EndTransfer()
{
    _ss = 1;
    status = OPENED;
}

ft_uint8_t FT813::Rd8(ft_uint32_t addr)
{
    ft_uint8_t value;
    StartTransfer(FT_GPU_READ, addr);
    value = Transfer8(0);
    EndTransfer();
    return value;
}

ft_uint16_t FT813::Rd16(ft_uint32_t addr)
{
    ft_uint16_t value;
    StartTransfer(FT_GPU_READ, addr);
    value = Transfer16(0);
    EndTransfer();
    return value;
}

ft_uint32_t FT813::Rd32(ft_uint32_t addr)
{
    ft_uint32_t value;
    StartTransfer(FT_GPU_READ, addr);
    value = Transfer32(0);
    EndTransfer();
    return value;
}

ft_void_t FT813::Wr8(ft_uint32_t addr, ft_uint8_t v)
{
//    StartTransfer(FT_GPU_WRITE, addr);
//    if (FT_GPU_READ == rw) {  // if (FT_GPU_READ == FT_GPU_WRITE)
//        _ss = 0;       // cs low
//        _spi.write(addr >> 16);
//        _spi.write(addr >> 8);
//        _spi.write(addr & 0xff);
//        _spi.write(0); //Dummy Read Byte
//        status = READING;
//    } else {
        _ss = 0;       // cs low
        _spi.write(0x80 | (addr >> 16));
        _spi.write(addr >> 8);
        _spi.write(addr & 0xff);
        status = WRITING;
//    }

//    Transfer8(v);
    _spi.write(v);
//    EndTransfer();
    _ss = 1;
    status = OPENED;
}

ft_void_t FT813::Wr16(ft_uint32_t addr, ft_uint16_t v)
{
    StartTransfer(FT_GPU_WRITE, addr);
    Transfer16(v);
    EndTransfer();
}

ft_void_t FT813::Wr32(ft_uint32_t addr, ft_uint32_t v)
{
    StartTransfer(FT_GPU_WRITE, addr);
    Transfer32(v);
    EndTransfer();
}

ft_void_t FT813::HostCommand(ft_uint8_t cmd)
{
  _ss = 0;
  _spi.write(cmd);
  _spi.write(0);
  _spi.write(0);
  _ss = 1;
}

ft_void_t FT813::ClockSelect(FT_GPU_PLL_SOURCE_T pllsource)
{
   HostCommand(pllsource);
}

ft_void_t FT813::PLL_FreqSelect(FT_GPU_PLL_FREQ_T freq)
{
   HostCommand(freq);
}

ft_void_t FT813::PowerModeSwitch(FT_GPU_POWER_MODE_T pwrmode)
{
   HostCommand(pwrmode);
}

ft_void_t FT813::CoreReset()
{
   HostCommand(0x68);
}

ft_void_t FT813::Updatecmdfifo(ft_uint16_t count)
{
     cmd_fifo_wp  = (cmd_fifo_wp + count) & 4095;
    //4 byte alignment
     cmd_fifo_wp = (cmd_fifo_wp + 3) & 0xffc;
    Wr16(REG_CMD_WRITE, cmd_fifo_wp);
}

ft_uint16_t FT813::fifo_Freespace()
{
    ft_uint16_t fullness,retval;

    fullness = (cmd_fifo_wp - Rd16(REG_CMD_READ)) & 4095;
    retval = (FT_CMD_FIFO_SIZE - 4) - fullness;
    return (retval);
}

ft_void_t FT813::WrCmdBuf(ft_uint8_t *buffer, ft_uint16_t count)
{
    ft_uint32_t length =0, SizeTransfered = 0;

#define MAX_CMD_FIFO_TRANSFER   fifo_Freespace()
    do {
        length = count;
        if (length > MAX_CMD_FIFO_TRANSFER) {
            length = MAX_CMD_FIFO_TRANSFER;
        }
        CheckCmdBuffer(length);

        StartCmdTransfer(FT_GPU_WRITE, length);

        SizeTransfered = 0;
        while (length--) {
//            Transfer8(*buffer);
            _spi.write(*buffer);
            buffer++;
            SizeTransfered++;
        }
        length = SizeTransfered;

        EndTransfer();
        Updatecmdfifo(length);

        WaitCmdfifo_empty();

        count -= length;
    } while (count > 0);
}

ft_void_t FT813::WrCmdBufFromFlash(FT_PROGMEM ft_prog_uchar8_t *buffer, ft_uint16_t count)
{
    ft_uint32_t length =0, SizeTransfered = 0;

#define MAX_CMD_FIFO_TRANSFER   fifo_Freespace()
    do {
        length = count;
        if (length > MAX_CMD_FIFO_TRANSFER) {
            length = MAX_CMD_FIFO_TRANSFER;
        }
        CheckCmdBuffer(length);

        StartCmdTransfer(FT_GPU_WRITE,length);

        SizeTransfered = 0;
        while (length--) {
            Transfer8(ft_pgm_read_byte_near(buffer));
            buffer++;
            SizeTransfered++;
        }
        length = SizeTransfered;

        EndTransfer();
        Updatecmdfifo(length);

        WaitCmdfifo_empty();

        count -= length;
    } while (count > 0);
}

ft_void_t FT813::CheckCmdBuffer(ft_uint16_t count)
{
   ft_uint16_t getfreespace;
   do {
        getfreespace = fifo_Freespace();
   } while(getfreespace < count);
}

ft_void_t FT813::WaitCmdfifo_empty()
{
   while(Rd16(REG_CMD_READ) != Rd16(REG_CMD_WRITE));

    cmd_fifo_wp = Rd16(REG_CMD_WRITE);
}

ft_void_t FT813::WaitLogo_Finish()
{
    ft_int16_t cmdrdptr, cmdwrptr;

    do {
         cmdrdptr = Rd16(REG_CMD_READ);
         cmdwrptr = Rd16(REG_CMD_WRITE);
    } while ((cmdwrptr != cmdrdptr) || (cmdrdptr != 0));
    cmd_fifo_wp = 0;
}

ft_void_t FT813::ResetCmdFifo()
{
    cmd_fifo_wp = 0;
}

ft_void_t FT813::WrCmd32(ft_uint32_t cmd)
{
     CheckCmdBuffer(sizeof(cmd));

     Wr32(RAM_CMD + cmd_fifo_wp, cmd);

     Updatecmdfifo(sizeof(cmd));
}

ft_void_t FT813::ResetDLBuffer()
{
    dl_buff_wp = 0;
}

/* Toggle PD_N pin of FT813 board for a power cycle*/
ft_void_t FT813::Powercycle(ft_bool_t up)
{
    if (up)
    {
        //Toggle PD_N from low to high for power up switch
        _pd = 0;
        Sleep(20);

        _pd = 1;
        Sleep(20);
    } else {
        //Toggle PD_N from high to low for power down switch
        _pd = 1;
        Sleep(20);

        _pd = 0;
        Sleep(20);
    }
}

ft_void_t FT813::WrMemFromFlash(ft_uint32_t addr, const ft_prog_uchar8_t *buffer, ft_uint32_t length)
{
    //ft_uint32_t SizeTransfered = 0;

    StartTransfer(FT_GPU_WRITE,addr);

    while (length--) {
        Transfer8(ft_pgm_read_byte_near(buffer));
        buffer++;
    }

    EndTransfer();
}

ft_void_t FT813::WrMem(ft_uint32_t addr, const ft_uint8_t *buffer, ft_uint32_t length)
{
    //ft_uint32_t SizeTransfered = 0;

    StartTransfer(FT_GPU_WRITE,addr);

    while (length--) {
        Transfer8(*buffer);
        buffer++;
    }

    EndTransfer();
}

ft_void_t FT813::RdMem(ft_uint32_t addr, ft_uint8_t *buffer, ft_uint32_t length)
{
    //ft_uint32_t SizeTransfered = 0;

    StartTransfer(FT_GPU_READ,addr);

    while (length--) {
       *buffer = Transfer8(0);
       buffer++;
    }

    EndTransfer();
}

ft_int32_t FT813::Dec2Ascii(ft_char8_t *pSrc, ft_int32_t value)
{
    ft_int16_t Length;
    ft_char8_t *pdst, charval;
    ft_int32_t CurrVal = value, tmpval,i;
    ft_char8_t tmparray[16], idx = 0;

    Length = strlen(pSrc);
    pdst = pSrc + Length;

    if(0 == value) {
        *pdst++ = '0';
        *pdst++ = '\0';
        return 0;
    }

    if(CurrVal < 0) {
        *pdst++ = '-';
        CurrVal = - CurrVal;
    }
    /* insert the value */
    while(CurrVal > 0) {
        tmpval = CurrVal;
        CurrVal /= 10;
        tmpval = tmpval - CurrVal*10;
        charval = '0' + tmpval;
        tmparray[idx++] = charval;
    }

    for(i = 0; i < idx; i++) {
        *pdst++ = tmparray[idx - i - 1];
    }
    *pdst++ = '\0';

    return 0;
}

ft_void_t FT813::Sleep(ft_uint16_t ms)
{
    wait_ms(ms);
}

ft_void_t FT813::Sound_ON()
{
     Wr8(REG_GPIO, 0x02 | Rd8(REG_GPIO));
}

ft_void_t FT813::Sound_OFF()
{
     Wr8(REG_GPIO, 0xFD & Rd8(REG_GPIO));
}