Diff: AplicationLayer/DebugCommander.cpp

Revision:

0:3dac4f477e98

Child:

1:0c1053275589

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/AplicationLayer/DebugCommander.cpp	Wed Jul 08 17:50:18 2015 +0000
@@ -0,0 +1,176 @@
+#include "SysConfig.h"
+
+#define SMUX_MHZ19  0
+#define SMUX_ZPH01  1
+#define SMUX_ESP01  2
+#define SMUX_ZE08   3
+
+#define uart_db uart_pc
+
+void LedFlasher(void)
+{
+    int ledNumOn;
+    for(ledNumOn = 1; ledNumOn < LED_NUM_MAX; ledNumOn++)
+    {
+        LedOffAll();
+        LedOn(ledNumOn);
+        wait_ms(300);
+    }
+}
+
+void DebugFunc_CO2(void)
+{
+    uart_db.printf("Reading MHZ19...");
+    SerialMuxSel(SMUX_MHZ19);
+    int co2Vol = MHZ19_ReadCO2();
+    if(co2Vol < 0)
+        uart_db.printf("CheckSum Error!\n\r");
+    else
+        uart_db.printf("OK!\n\rCO2 Vol = %dppm.\n\r", co2Vol);    
+}
+
+void DebugFunc_PM25(void)
+{
+    float pm25Vol = 0, pm25VolAvg = 0;
+    int cnt = 0, cnt_max = 30;
+    uart_db.printf("Reading ZPH01 (need %dsec)...", cnt_max);
+    SerialMuxSel(SMUX_ZPH01);
+    
+    while(cnt < cnt_max)
+    {
+        pm25Vol = ZPH01_ReadPM25();
+        if(pm25Vol < 0)
+        {
+            uart_db.printf("CheckSum Error!\n\rRepeat reading...");
+        }
+        else
+        {
+            pm25VolAvg += pm25Vol;
+            cnt++;
+        }
+    }    
+    pm25VolAvg = pm25VolAvg / cnt_max;
+    uart_db.printf("OK!\n\rPM2.5 Vol = %dug/m^3.\n\r", pm25VolAvg);
+}
+
+void DebugFunc_CH2O(void)
+{
+    uart_db.printf("Reading ZE08...");
+    SerialMuxSel(SMUX_ZE08);
+    int ch2oVol = ZE08_ReadCH2O();
+    if(ch2oVol < 0)
+        uart_db.printf("CheckSum Error!\n\r");
+    else
+        uart_db.printf("OK!\n\rCH2O Vol = %dug/m^3.\n\r", ch2oVol);                              
+}
+
+void DebugFunc_TempRh(void)
+{
+    uart_db.printf("Reading SHT20...");
+    float temp = SHT20_ReadTemp();
+    float rh = SHT20_ReadRh();
+    uart_db.printf("OK!\n\rTemperature = %.2f, Humidity = %2.f\n\r", temp, rh);                
+}
+
+void DebugFunc_AirPress(void)
+{
+    uart_db.printf("Not implemented...");
+}
+
+void DebugFunc_UvLevel(void)
+{
+    uart_db.printf("Not implemented...");
+}
+
+void DebugFunc_WiFi(void)
+{
+    uart_db.printf("Not implemented...");
+}
+
+void DebugFunc_SwitchSmux(void)
+{
+    uart_db.printf("Please type SMUX channel(0~3) with ENTER.\n\r");
+    while(!uart_db.readable());
+    uint8_t ch = uart_db.getc();
+    SerialMuxSel(ch - '0');
+    uart_db.printf("Switched to ch %c.\n\r", ch);    
+}
+
+void DebugCommander(void)
+{   
+    int quitFlag = 0, cmdPc;
+    while(!quitFlag)
+    {             
+        uart_db.printf("\n\r\n\r============ AirBox Nucleo Adaptor Demo ============\n\r\n\r");
+        uart_db.printf(" 0. All sensors auto Test.\n\r");        
+        uart_db.printf(" 1. Test CO2 gas sensor.\n\r");
+        uart_db.printf(" 2. Test PM2.5 dust sensor.\n\r");        
+        uart_db.printf(" 3. Test CH2O gas sensor.\n\r");
+        uart_db.printf(" 4. Test temperature & humidity sensor.\n\r");
+        uart_db.printf(" 5. Test air pressure sensor.\n\r");
+        uart_db.printf(" 6. Test UV light level.\n\r");
+        uart_db.printf(" w. Test WiFi module.\n\r");
+        uart_db.printf(" m. Manual switch SMUX channel.\n\r");        
+        uart_db.printf(" q. Exit demo.\n\r\n\r");
+                              
+        while(!uart_db.readable())
+        {
+            #if 0
+            if(uart_sen.readable())
+                uart_db.printf(" <0x%02X> ", uart_sen.getc());
+            #endif
+        }
+        cmdPc = uart_db.getc();
+        
+        switch(cmdPc)
+        {
+            case 'q':
+                quitFlag = 1;
+                uart_db.printf("\n\rExiting demo...\n\r");
+                break;  
+                
+            case 'm':
+                DebugFunc_SwitchSmux();
+                break;        
+                      
+            case 'w':
+                DebugFunc_WiFi();
+                break;              
+                
+            case '1':
+                DebugFunc_CO2();
+                break;
+
+            case '2':
+                DebugFunc_PM25();
+                break;
+                
+            case '3':                    
+                DebugFunc_CH2O();
+                break;
+                
+            case '4':
+                DebugFunc_TempRh();
+                break;
+  
+            case '5':
+                DebugFunc_AirPress();
+                break;
+                
+            case '6':
+                DebugFunc_UvLevel();
+                break;    
+            default:
+                uart_db.printf("Incorrect input!\n\r");
+                break;
+        }
+    
+        uart_db.printf("\n\rPress any key...\n\r");
+                          
+        while(!uart_db.readable());
+        cmdPc = uart_db.getc();
+        
+    }    
+    
+}
+ 
\ No newline at end of file