fix LPC812 PWM
Fork of mbed-dev by
Diff: targets/cmsis/TARGET_STM/TARGET_STM32L4/stm32l4xx_hal_usart.c
- Revision:
- 0:9b334a45a8ff
diff -r 000000000000 -r 9b334a45a8ff targets/cmsis/TARGET_STM/TARGET_STM32L4/stm32l4xx_hal_usart.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_STM32L4/stm32l4xx_hal_usart.c Thu Oct 01 15:25:22 2015 +0300 @@ -0,0 +1,1817 @@ +/** + ****************************************************************************** + * @file stm32l4xx_hal_usart.c + * @author MCD Application Team + * @version V1.0.0 + * @date 26-June-2015 + * @brief USART HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Universal Synchronous/Asynchronous Receiver Transmitter + * Peripheral (USART). + * + Initialization and de-initialization functions + * + IO operation functions + * + Peripheral Control functions + * + Peripheral State and Error functions + * + @verbatim + =============================================================================== + ##### How to use this driver ##### + =============================================================================== + [..] + The USART HAL driver can be used as follows: + + (#) Declare a USART_HandleTypeDef handle structure (eg. USART_HandleTypeDef husart). + (#) Initialize the USART low level resources by implementing the HAL_USART_MspInit() API: + (++) Enable the USARTx interface clock. + (++) USART pins configuration: + (+++) Enable the clock for the USART GPIOs. + (+++) Configure these USART pins as alternate function pull-up. + (++) NVIC configuration if you need to use interrupt process (HAL_USART_Transmit_IT(), + HAL_USART_Receive_IT() and HAL_USART_TransmitReceive_IT() APIs): + (+++) Configure the USARTx interrupt priority. + (+++) Enable the NVIC USART IRQ handle. + (++) USART interrupts handling: + -@@- The specific USART interrupts (Transmission complete interrupt, + RXNE interrupt and Error Interrupts) will be managed using the macros + __HAL_USART_ENABLE_IT() and __HAL_USART_DISABLE_IT() inside the transmit and receive process. + (++) DMA Configuration if you need to use DMA process (HAL_USART_Transmit_DMA() + HAL_USART_Receive_DMA() and HAL_USART_TransmitReceive_DMA() APIs): + (+++) Declare a DMA handle structure for the Tx/Rx channel. + (+++) Enable the DMAx interface clock. + (+++) Configure the declared DMA handle structure with the required Tx/Rx parameters. + (+++) Configure the DMA Tx/Rx channel. + (+++) Associate the initialized DMA handle to the USART DMA Tx/Rx handle. + (+++) Configure the priority and enable the NVIC for the transfer complete interrupt on the DMA Tx/Rx channel. + + (#) Program the Baud Rate, Word Length, Stop Bit, Parity, Hardware + flow control and Mode (Receiver/Transmitter) in the husart handle Init structure. + + (#) Initialize the USART registers by calling the HAL_USART_Init() API: + (++) This API configures also the low level Hardware GPIO, CLOCK, CORTEX...etc) + by calling the customized HAL_USART_MspInit(&husart) API. + + [..] + (@) To configure and enable/disable the USART to wake up the MCU from stop mode, resort to UART API's + HAL_UARTEx_StopModeWakeUpSourceConfig(), HAL_UARTEx_EnableStopMode() and + HAL_UARTEx_DisableStopMode() in casting the USART handle to UART type UART_HandleTypeDef. + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32l4xx_hal.h" + +/** @addtogroup STM32L4xx_HAL_Driver + * @{ + */ + +/** @defgroup USART USART + * @brief HAL USART Synchronous module driver + * @{ + */ + +#ifdef HAL_USART_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @defgroup USART_Private_Constants USART Private Constants + * @{ + */ +#define USART_DUMMY_DATA ((uint16_t) 0xFFFF) /*!< USART transmitted dummy data */ +#define USART_TEACK_REACK_TIMEOUT ((uint32_t) 1000) /*!< USART TX or RX enable acknowledge time-out value */ +#define USART_CR1_FIELDS ((uint32_t)(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | \ + USART_CR1_TE | USART_CR1_RE | USART_CR1_OVER8)) /*!< USART CR1 fields of parameters set by USART_SetConfig API */ +#define USART_CR2_FIELDS ((uint32_t)(USART_CR2_CPHA | USART_CR2_CPOL | \ + USART_CR2_CLKEN | USART_CR2_LBCL | USART_CR2_STOP)) /*!< USART CR2 fields of parameters set by USART_SetConfig API */ +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/** @addtogroup USART_Private_Functions + * @{ + */ +static void USART_DMATransmitCplt(DMA_HandleTypeDef *hdma); +static void USART_DMAReceiveCplt(DMA_HandleTypeDef *hdma); +static void USART_DMATxHalfCplt(DMA_HandleTypeDef *hdma); +static void USART_DMARxHalfCplt(DMA_HandleTypeDef *hdma); +static void USART_DMAError(DMA_HandleTypeDef *hdma); +static HAL_StatusTypeDef USART_WaitOnFlagUntilTimeout(USART_HandleTypeDef *husart, uint32_t Flag, FlagStatus Status, uint32_t Timeout); +static HAL_StatusTypeDef USART_SetConfig(USART_HandleTypeDef *husart); +static HAL_StatusTypeDef USART_CheckIdleState(USART_HandleTypeDef *husart); +static HAL_StatusTypeDef USART_Transmit_IT(USART_HandleTypeDef *husart); +static HAL_StatusTypeDef USART_EndTransmit_IT(USART_HandleTypeDef *husart); +static HAL_StatusTypeDef USART_Receive_IT(USART_HandleTypeDef *husart); +static HAL_StatusTypeDef USART_TransmitReceive_IT(USART_HandleTypeDef *husart); +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ + +/** @defgroup USART_Exported_Functions USART Exported Functions + * @{ + */ + +/** @defgroup USART_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and Configuration functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to initialize the USART + in asynchronous and in synchronous modes. + (+) For the asynchronous mode only these parameters can be configured: + (++) Baud Rate + (++) Word Length + (++) Stop Bit + (++) Parity: If the parity is enabled, then the MSB bit of the data written + in the data register is transmitted but is changed by the parity bit. + Depending on the frame length defined by the M1 and M0 bits (7-bit, + 8-bit or 9-bit), the possible USART frame formats are as listed in the + following table: + + (+++) Table 1. USART frame format. + (+++) +-----------------------------------------------------------------------+ + (+++) | M1 bit | M0 bit | PCE bit | USART frame | + (+++) |---------|---------|-----------|---------------------------------------| + (+++) | 0 | 0 | 0 | | SB | 8 bit data | STB | | + (+++) |---------|---------|-----------|---------------------------------------| + (+++) | 0 | 0 | 1 | | SB | 7 bit data | PB | STB | | + (+++) |---------|---------|-----------|---------------------------------------| + (+++) | 0 | 1 | 0 | | SB | 9 bit data | STB | | + (+++) |---------|---------|-----------|---------------------------------------| + (+++) | 0 | 1 | 1 | | SB | 8 bit data | PB | STB | | + (+++) |---------|---------|-----------|---------------------------------------| + (+++) | 1 | 0 | 0 | | SB | 7 bit data | STB | | + (+++) |---------|---------|-----------|---------------------------------------| + (+++) | 1 | 0 | 1 | | SB | 6 bit data | PB | STB | | + (+++) +-----------------------------------------------------------------------+ + (++) USART polarity + (++) USART phase + (++) USART LastBit + (++) Receiver/transmitter modes + + [..] + The HAL_USART_Init() function follows the USART synchronous configuration + procedure (details for the procedure are available in reference manual). + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the USART mode according to the specified + * parameters in the USART_InitTypeDef and initialize the associated handle. + * @param husart: USART handle. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_Init(USART_HandleTypeDef *husart) +{ + /* Check the USART handle allocation */ + if(husart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_USART_INSTANCE(husart->Instance)); + + if(husart->State == HAL_USART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + husart->Lock = HAL_UNLOCKED; + + /* Init the low level hardware : GPIO, CLOCK */ + HAL_USART_MspInit(husart); + } + + husart->State = HAL_USART_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_USART_DISABLE(husart); + + /* Set the Usart Communication parameters */ + if (USART_SetConfig(husart) == HAL_ERROR) + { + return HAL_ERROR; + } + + /* In Synchronous mode, the following bits must be kept cleared: + - LINEN bit in the USART_CR2 register + - HDSEL, SCEN and IREN bits in the USART_CR3 register.*/ + husart->Instance->CR2 &= ~USART_CR2_LINEN; + husart->Instance->CR3 &= ~(USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN); + + /* Enable the Peripheral */ + __HAL_USART_ENABLE(husart); + + /* TEACK and/or REACK to check before moving husart->State to Ready */ + return (USART_CheckIdleState(husart)); +} + +/** + * @brief DeInitialize the USART peripheral. + * @param husart: USART handle. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_DeInit(USART_HandleTypeDef *husart) +{ + /* Check the USART handle allocation */ + if(husart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_USART_INSTANCE(husart->Instance)); + + husart->State = HAL_USART_STATE_BUSY; + + husart->Instance->CR1 = 0x0; + husart->Instance->CR2 = 0x0; + husart->Instance->CR3 = 0x0; + + /* DeInit the low level hardware */ + HAL_USART_MspDeInit(husart); + + husart->ErrorCode = HAL_USART_ERROR_NONE; + husart->State = HAL_USART_STATE_RESET; + + /* Process Unlock */ + __HAL_UNLOCK(husart); + + return HAL_OK; +} + +/** + * @brief Initialize the USART MSP. + * @param husart: USART handle. + * @retval None + */ + __weak void HAL_USART_MspInit(USART_HandleTypeDef *husart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_USART_MspInit can be implemented in the user file + */ +} + +/** + * @brief DeInitialize the USART MSP. + * @param husart: USART handle. + * @retval None + */ + __weak void HAL_USART_MspDeInit(USART_HandleTypeDef *husart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_USART_MspDeInit can be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup USART_Exported_Functions_Group2 IO operation functions + * @brief USART Transmit and Receive functions + * +@verbatim + =============================================================================== + ##### IO operation functions ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to manage the USART synchronous + data transfers. + + [..] The USART supports master mode only: it cannot receive or send data related to an input + clock (SCLK is always an output). + + (#) There are two modes of transfer: + (++) Blocking mode: The communication is performed in polling mode. + The HAL status of all data processing is returned by the same function + after finishing transfer. + (++) No-Blocking mode: The communication is performed using Interrupts + or DMA, These API's return the HAL status. + The end of the data processing will be indicated through the + dedicated USART IRQ when using Interrupt mode or the DMA IRQ when + using DMA mode. + The HAL_USART_TxCpltCallback(), HAL_USART_RxCpltCallback() and HAL_USART_TxRxCpltCallback() user callbacks + will be executed respectively at the end of the transmit or Receive process + The HAL_USART_ErrorCallback()user callback will be executed when a communication error is detected + + (#) Blocking mode API's are : + (++) HAL_USART_Transmit()in simplex mode + (++) HAL_USART_Receive() in full duplex receive only + (++) HAL_USART_TransmitReceive() in full duplex mode + + (#) Non-Blocking mode API's with Interrupt are : + (++) HAL_USART_Transmit_IT()in simplex mode + (++) HAL_USART_Receive_IT() in full duplex receive only + (++) HAL_USART_TransmitReceive_IT()in full duplex mode + (++) HAL_USART_IRQHandler() + + (#) No-Blocking mode API's with DMA are : + (++) HAL_USART_Transmit_DMA()in simplex mode + (++) HAL_USART_Receive_DMA() in full duplex receive only + (++) HAL_USART_TransmitReceive_DMA() in full duplex mode + (++) HAL_USART_DMAPause() + (++) HAL_USART_DMAResume() + (++) HAL_USART_DMAStop() + + (#) A set of Transfer Complete Callbacks are provided in No_Blocking mode: + (++) HAL_USART_TxCpltCallback() + (++) HAL_USART_RxCpltCallback() + (++) HAL_USART_TxHalfCpltCallback() + (++) HAL_USART_RxHalfCpltCallback() + (++) HAL_USART_ErrorCallback() + (++) HAL_USART_TxRxCpltCallback() + +@endverbatim + * @{ + */ + +/** + * @brief Simplex send an amount of data in blocking mode. + * @param husart: USART handle. + * @param pTxData: Pointer to data buffer. + * @param Size: Amount of data to be sent. + * @param Timeout: Timeout duration. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_Transmit(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size, uint32_t Timeout) +{ + uint16_t* tmp; + + if(husart->State == HAL_USART_STATE_READY) + { + if((pTxData == NULL) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(husart); + + husart->ErrorCode = HAL_USART_ERROR_NONE; + husart->State = HAL_USART_STATE_BUSY_TX; + + husart->TxXferSize = Size; + husart->TxXferCount = Size; + + /* Check the remaining data to be sent */ + while(husart->TxXferCount > 0) + { + husart->TxXferCount--; + if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TC, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) + { + tmp = (uint16_t*) pTxData; + husart->Instance->TDR = (*tmp & (uint16_t)0x01FF); + pTxData += 2; + } + else + { + husart->Instance->TDR = (*pTxData++ & (uint8_t)0xFF); + } + } + + if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TC, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + husart->State = HAL_USART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive an amount of data in blocking mode. + * @note To receive synchronous data, dummy data are simultaneously transmitted. + * @param husart: USART handle. + * @param pRxData: Pointer to data buffer. + * @param Size: Amount of data to be received. + * @param Timeout: Timeout duration. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_Receive(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size, uint32_t Timeout) +{ + uint16_t* tmp; + uint16_t uhMask; + + if(husart->State == HAL_USART_STATE_READY) + { + if((pRxData == NULL) || (Size == 0)) + { + return HAL_ERROR; + } + /* Process Locked */ + __HAL_LOCK(husart); + + husart->ErrorCode = HAL_USART_ERROR_NONE; + husart->State = HAL_USART_STATE_BUSY_RX; + + husart->RxXferSize = Size; + husart->RxXferCount = Size; + + /* Computation of USART mask to apply to RDR register */ + USART_MASK_COMPUTATION(husart); + uhMask = husart->Mask; + + /* as long as data have to be received */ + while(husart->RxXferCount > 0) + { + husart->RxXferCount--; + + /* Wait until TC flag is set to send dummy byte in order to generate the + * clock for the slave to send data. + * Whatever the frame length (7, 8 or 9-bit long), the same dummy value + * can be written for all the cases. */ + if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TC, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + husart->Instance->TDR = (USART_DUMMY_DATA & (uint16_t)0x0FF); + + /* Wait for RXNE Flag */ + if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_RXNE, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) + { + tmp = (uint16_t*) pRxData ; + *tmp = (uint16_t)(husart->Instance->RDR & uhMask); + pRxData +=2; + } + else + { + *pRxData++ = (uint8_t)(husart->Instance->RDR & (uint8_t)uhMask); + } + } + + husart->State = HAL_USART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Full-Duplex Send and Receive an amount of data in blocking mode. + * @param husart: USART handle. + * @param pTxData: pointer to TX data buffer. + * @param pRxData: pointer to RX data buffer. + * @param Size: amount of data to be sent (same amount to be received). + * @param Timeout: Timeout duration. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_TransmitReceive(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size, uint32_t Timeout) +{ + uint16_t* tmp; + uint16_t uhMask; + + if(husart->State == HAL_USART_STATE_READY) + { + if((pTxData == NULL) || (pRxData == NULL) || (Size == 0)) + { + return HAL_ERROR; + } + /* Process Locked */ + __HAL_LOCK(husart); + + husart->ErrorCode = HAL_USART_ERROR_NONE; + husart->State = HAL_USART_STATE_BUSY_RX; + + husart->RxXferSize = Size; + husart->TxXferSize = Size; + husart->TxXferCount = Size; + husart->RxXferCount = Size; + + /* Computation of USART mask to apply to RDR register */ + USART_MASK_COMPUTATION(husart); + uhMask = husart->Mask; + + /* Check the remain data to be sent */ + while(husart->TxXferCount > 0) + { + husart->TxXferCount--; + husart->RxXferCount--; + + /* Wait until TC flag is set to send data */ + if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TC, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) + { + tmp = (uint16_t*) pTxData; + husart->Instance->TDR = (*tmp & uhMask); + pTxData += 2; + } + else + { + husart->Instance->TDR = (*pTxData++ & (uint8_t)uhMask); + } + + /* Wait for RXNE Flag */ + if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_RXNE, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) + { + tmp = (uint16_t*) pRxData ; + *tmp = (uint16_t)(husart->Instance->RDR & uhMask); + pRxData +=2; + } + else + { + *pRxData++ = (uint8_t)(husart->Instance->RDR & (uint8_t)uhMask); + } + } + + husart->State = HAL_USART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Send an amount of data in interrupt mode. + * @param husart: USART handle. + * @param pTxData: pointer to data buffer. + * @param Size: amount of data to be sent. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_Transmit_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size) +{ + if(husart->State == HAL_USART_STATE_READY) + { + if((pTxData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(husart); + + husart->pTxBuffPtr = pTxData; + husart->TxXferSize = Size; + husart->TxXferCount = Size; + + husart->ErrorCode = HAL_USART_ERROR_NONE; + husart->State = HAL_USART_STATE_BUSY_TX; + + /* The USART Error Interrupts: (Frame error, noise error, overrun error) + are not managed by the USART Transmit Process to avoid the overrun interrupt + when the usart mode is configured for transmit and receive "USART_MODE_TX_RX" + to benefit for the frame error and noise interrupts the usart mode should be + configured only for transmit "USART_MODE_TX" */ + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + /* Enable the USART Transmit Data Register Empty Interrupt */ + __HAL_USART_ENABLE_IT(husart, USART_IT_TXE); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive an amount of data in blocking mode. + * @note To receive synchronous data, dummy data are simultaneously transmitted. + * @param husart: USART handle. + * @param pRxData: pointer to data buffer. + * @param Size: amount of data to be received. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_Receive_IT(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size) +{ + if(husart->State == HAL_USART_STATE_READY) + { + if((pRxData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + /* Process Locked */ + __HAL_LOCK(husart); + + husart->pRxBuffPtr = pRxData; + husart->RxXferSize = Size; + husart->RxXferCount = Size; + + USART_MASK_COMPUTATION(husart); + + husart->ErrorCode = HAL_USART_ERROR_NONE; + husart->State = HAL_USART_STATE_BUSY_RX; + + /* Enable the USART Parity Error Interrupt */ + __HAL_USART_ENABLE_IT(husart, USART_IT_PE); + + /* Enable the USART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_USART_ENABLE_IT(husart, USART_IT_ERR); + + /* Enable the USART Data Register not empty Interrupt */ + __HAL_USART_ENABLE_IT(husart, USART_IT_RXNE); + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + + /* Send dummy byte in order to generate the clock for the Slave to send the next data */ + if(husart->Init.WordLength == USART_WORDLENGTH_9B) + { + husart->Instance->TDR = (USART_DUMMY_DATA & (uint16_t)0x01FF); + } + else + { + husart->Instance->TDR = (USART_DUMMY_DATA & (uint16_t)0x00FF); + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Full-Duplex Send and Receive an amount of data in interrupt mode. + * @param husart: USART handle. + * @param pTxData: pointer to TX data buffer. + * @param pRxData: pointer to RX data buffer. + * @param Size: amount of data to be sent (same amount to be received). + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_TransmitReceive_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size) +{ + + if(husart->State == HAL_USART_STATE_READY) + { + if((pTxData == NULL) || (pRxData == NULL) || (Size == 0)) + { + return HAL_ERROR; + } + /* Process Locked */ + __HAL_LOCK(husart); + + husart->pRxBuffPtr = pRxData; + husart->RxXferSize = Size; + husart->RxXferCount = Size; + husart->pTxBuffPtr = pTxData; + husart->TxXferSize = Size; + husart->TxXferCount = Size; + + /* Computation of USART mask to apply to RDR register */ + USART_MASK_COMPUTATION(husart); + + husart->ErrorCode = HAL_USART_ERROR_NONE; + husart->State = HAL_USART_STATE_BUSY_TX_RX; + + /* Enable the USART Data Register not empty Interrupt */ + __HAL_USART_ENABLE_IT(husart, USART_IT_RXNE); + + /* Enable the USART Parity Error Interrupt */ + __HAL_USART_ENABLE_IT(husart, USART_IT_PE); + + /* Enable the USART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_USART_ENABLE_IT(husart, USART_IT_ERR); + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + /* Enable the USART Transmit Data Register Empty Interrupt */ + __HAL_USART_ENABLE_IT(husart, USART_IT_TXE); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } + +} + +/** + * @brief Send an amount of data in DMA mode. + * @param husart: USART handle. + * @param pTxData: pointer to data buffer. + * @param Size: amount of data to be sent. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_Transmit_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size) +{ + uint32_t *tmp; + + if(husart->State == HAL_USART_STATE_READY) + { + if((pTxData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + /* Process Locked */ + __HAL_LOCK(husart); + + husart->pTxBuffPtr = pTxData; + husart->TxXferSize = Size; + husart->TxXferCount = Size; + + husart->ErrorCode = HAL_USART_ERROR_NONE; + husart->State = HAL_USART_STATE_BUSY_TX; + + /* Set the USART DMA transfer complete callback */ + husart->hdmatx->XferCpltCallback = USART_DMATransmitCplt; + + /* Set the USART DMA Half transfer complete callback */ + husart->hdmatx->XferHalfCpltCallback = USART_DMATxHalfCplt; + + /* Set the DMA error callback */ + husart->hdmatx->XferErrorCallback = USART_DMAError; + + /* Enable the USART transmit DMA channel */ + tmp = (uint32_t*)&pTxData; + HAL_DMA_Start_IT(husart->hdmatx, *(uint32_t*)tmp, (uint32_t)&husart->Instance->TDR, Size); + + /* Clear the TC flag in the ICR register */ + __HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_TCF); + + /* Enable the DMA transfer for transmit request by setting the DMAT bit + in the USART CR3 register */ + husart->Instance->CR3 |= USART_CR3_DMAT; + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive an amount of data in DMA mode. + * @param husart: USART handle. + * @param pRxData: pointer to data buffer. + * @param Size: amount of data to be received. + * @note When the USART parity is enabled (PCE = 1), the received data contain + * the parity bit (MSB position). + * @note The USART DMA transmit channel must be configured in order to generate the clock for the slave. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_Receive_DMA(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size) +{ + uint32_t *tmp; + + if(husart->State == HAL_USART_STATE_READY) + { + if((pRxData == NULL ) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(husart); + + husart->pRxBuffPtr = pRxData; + husart->RxXferSize = Size; + husart->pTxBuffPtr = pRxData; + husart->TxXferSize = Size; + + husart->ErrorCode = HAL_USART_ERROR_NONE; + husart->State = HAL_USART_STATE_BUSY_RX; + + /* Set the USART DMA Rx transfer complete callback */ + husart->hdmarx->XferCpltCallback = USART_DMAReceiveCplt; + + /* Set the USART DMA Half transfer complete callback */ + husart->hdmarx->XferHalfCpltCallback = USART_DMARxHalfCplt; + + /* Set the USART DMA Rx transfer error callback */ + husart->hdmarx->XferErrorCallback = USART_DMAError; + + /* Enable the USART receive DMA channel */ + tmp = (uint32_t*)&pRxData; + HAL_DMA_Start_IT(husart->hdmarx, (uint32_t)&husart->Instance->RDR, *(uint32_t*)tmp, Size); + + /* Enable the USART transmit DMA channel: the transmit channel is used in order + to generate in the non-blocking mode the clock to the slave device, + this mode isn't a simplex receive mode but a full-duplex receive mode */ + tmp = (uint32_t*)&pRxData; + HAL_DMA_Start_IT(husart->hdmatx, *(uint32_t*)tmp, (uint32_t)&husart->Instance->TDR, Size); + + /* Enable the DMA transfer for the receiver request by setting the DMAR bit + in the USART CR3 register */ + husart->Instance->CR3 |= USART_CR3_DMAR; + + /* Enable the DMA transfer for transmit request by setting the DMAT bit + in the USART CR3 register */ + husart->Instance->CR3 |= USART_CR3_DMAT; + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Full-Duplex Transmit Receive an amount of data in non-blocking mode. + * @param husart: USART handle. + * @param pTxData: pointer to TX data buffer. + * @param pRxData: pointer to RX data buffer. + * @param Size: amount of data to be received/sent. + * @note When the USART parity is enabled (PCE = 1) the data received contain the parity bit. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_TransmitReceive_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size) +{ + uint32_t *tmp; + + if(husart->State == HAL_USART_STATE_READY) + { + if((pTxData == NULL) || (pRxData == NULL) || (Size == 0)) + { + return HAL_ERROR; + } + /* Process Locked */ + __HAL_LOCK(husart); + + husart->pRxBuffPtr = pRxData; + husart->RxXferSize = Size; + husart->pTxBuffPtr = pTxData; + husart->TxXferSize = Size; + + husart->ErrorCode = HAL_USART_ERROR_NONE; + husart->State = HAL_USART_STATE_BUSY_TX_RX; + + /* Set the USART DMA Rx transfer complete callback */ + husart->hdmarx->XferCpltCallback = USART_DMAReceiveCplt; + + /* Set the USART DMA Half transfer complete callback */ + husart->hdmarx->XferHalfCpltCallback = USART_DMARxHalfCplt; + + /* Set the USART DMA Tx transfer complete callback */ + husart->hdmatx->XferCpltCallback = USART_DMATransmitCplt; + + /* Set the USART DMA Half transfer complete callback */ + husart->hdmatx->XferHalfCpltCallback = USART_DMATxHalfCplt; + + /* Set the USART DMA Tx transfer error callback */ + husart->hdmatx->XferErrorCallback = USART_DMAError; + + /* Set the USART DMA Rx transfer error callback */ + husart->hdmarx->XferErrorCallback = USART_DMAError; + + /* Enable the USART receive DMA channel */ + tmp = (uint32_t*)&pRxData; + HAL_DMA_Start_IT(husart->hdmarx, (uint32_t)&husart->Instance->RDR, *(uint32_t*)tmp, Size); + + /* Enable the USART transmit DMA channel */ + tmp = (uint32_t*)&pTxData; + HAL_DMA_Start_IT(husart->hdmatx, *(uint32_t*)tmp, (uint32_t)&husart->Instance->TDR, Size); + + /* Clear the TC flag in the ICR register */ + __HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_TCF); + + /* Enable the DMA transfer for the receiver request by setting the DMAR bit + in the USART CR3 register */ + husart->Instance->CR3 |= USART_CR3_DMAR; + + /* Enable the DMA transfer for transmit request by setting the DMAT bit + in the USART CR3 register */ + husart->Instance->CR3 |= USART_CR3_DMAT; + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Pause the DMA Transfer. + * @param husart: USART handle. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_DMAPause(USART_HandleTypeDef *husart) +{ + /* Process Locked */ + __HAL_LOCK(husart); + + if(husart->State == HAL_USART_STATE_BUSY_TX) + { + /* Disable the USART DMA Tx request */ + husart->Instance->CR3 &= (uint32_t)(~USART_CR3_DMAT); + } + else if(husart->State == HAL_USART_STATE_BUSY_RX) + { + /* Disable the USART DMA Rx request */ + husart->Instance->CR3 &= (uint32_t)(~USART_CR3_DMAR); + } + else if(husart->State == HAL_USART_STATE_BUSY_TX_RX) + { + /* Disable the USART DMA Tx request */ + husart->Instance->CR3 &= (uint32_t)(~USART_CR3_DMAT); + /* Disable the USART DMA Rx request */ + husart->Instance->CR3 &= (uint32_t)(~USART_CR3_DMAR); + } + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_OK; +} + +/** + * @brief Resume the DMA Transfer. + * @param husart: USART handle. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_DMAResume(USART_HandleTypeDef *husart) +{ + /* Process Locked */ + __HAL_LOCK(husart); + + if(husart->State == HAL_USART_STATE_BUSY_TX) + { + /* Enable the USART DMA Tx request */ + husart->Instance->CR3 |= USART_CR3_DMAT; + } + else if(husart->State == HAL_USART_STATE_BUSY_RX) + { + /* Clear the Overrun flag before resuming the Rx transfer*/ + __HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_OREF); + + /* Enable the USART DMA Rx request */ + husart->Instance->CR3 |= USART_CR3_DMAR; + } + else if(husart->State == HAL_USART_STATE_BUSY_TX_RX) + { + /* Clear the Overrun flag before resuming the Rx transfer*/ + __HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_OREF); + + /* Enable the USART DMA Rx request before the DMA Tx request */ + husart->Instance->CR3 |= USART_CR3_DMAR; + + /* Enable the USART DMA Tx request */ + husart->Instance->CR3 |= USART_CR3_DMAT; + } + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_OK; +} + +/** + * @brief Stop the DMA Transfer. + * @param husart: USART handle. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_USART_DMAStop(USART_HandleTypeDef *husart) +{ + /* The Lock is not implemented on this API to allow the user application + to call the HAL USART API under callbacks HAL_USART_TxCpltCallback() / HAL_USART_RxCpltCallback() / + HAL_USART_TxHalfCpltCallback / HAL_USART_RxHalfCpltCallback: + indeed, when HAL_DMA_Abort() API is called, the DMA TX/RX Transfer or Half Transfer complete + interrupt is generated if the DMA transfer interruption occurs at the middle or at the end of + the stream and the corresponding call back is executed. */ + + /* Disable the USART Tx/Rx DMA requests */ + husart->Instance->CR3 &= ~USART_CR3_DMAT; + husart->Instance->CR3 &= ~USART_CR3_DMAR; + + /* Abort the USART DMA tx channel */ + if(husart->hdmatx != NULL) + { + HAL_DMA_Abort(husart->hdmatx); + } + /* Abort the USART DMA rx channel */ + if(husart->hdmarx != NULL) + { + HAL_DMA_Abort(husart->hdmarx); + } + + husart->State = HAL_USART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Handle USART interrupt request. + * @param husart: USART handle. + * @retval None + */ +void HAL_USART_IRQHandler(USART_HandleTypeDef *husart) +{ + + /* USART parity error interrupt occurred ------------------------------------*/ + if((__HAL_USART_GET_IT(husart, USART_IT_PE) != RESET) && (__HAL_USART_GET_IT_SOURCE(husart, USART_IT_PE) != RESET)) + { + __HAL_USART_CLEAR_IT(husart, USART_CLEAR_PEF); + husart->ErrorCode |= HAL_USART_ERROR_PE; + /* Set the USART state ready to be able to start again the process */ + husart->State = HAL_USART_STATE_READY; + } + + /* USART frame error interrupt occurred -------------------------------------*/ + if((__HAL_USART_GET_IT(husart, USART_IT_FE) != RESET) && (__HAL_USART_GET_IT_SOURCE(husart, USART_IT_ERR) != RESET)) + { + __HAL_USART_CLEAR_IT(husart, USART_CLEAR_FEF); + husart->ErrorCode |= HAL_USART_ERROR_FE; + /* Set the USART state ready to be able to start again the process */ + husart->State = HAL_USART_STATE_READY; + } + + /* USART noise error interrupt occurred -------------------------------------*/ + if((__HAL_USART_GET_IT(husart, USART_IT_NE) != RESET) && (__HAL_USART_GET_IT_SOURCE(husart, USART_IT_ERR) != RESET)) + { + __HAL_USART_CLEAR_IT(husart, USART_CLEAR_NEF); + husart->ErrorCode |= HAL_USART_ERROR_NE; + /* Set the USART state ready to be able to start again the process */ + husart->State = HAL_USART_STATE_READY; + } + + /* USART Over-Run interrupt occurred ----------------------------------------*/ + if((__HAL_USART_GET_IT(husart, USART_IT_ORE) != RESET) && (__HAL_USART_GET_IT_SOURCE(husart, USART_IT_ERR) != RESET)) + { + __HAL_USART_CLEAR_IT(husart, USART_CLEAR_OREF); + husart->ErrorCode |= HAL_USART_ERROR_ORE; + /* Set the USART state ready to be able to start again the process */ + husart->State = HAL_USART_STATE_READY; + } + + /* Call USART Error Call back function if need be --------------------------*/ + if(husart->ErrorCode != HAL_USART_ERROR_NONE) + { + HAL_USART_ErrorCallback(husart); + } + + /* USART in mode Receiver --------------------------------------------------*/ + if((__HAL_USART_GET_IT(husart, USART_IT_RXNE) != RESET) && (__HAL_USART_GET_IT_SOURCE(husart, USART_IT_RXNE) != RESET)) + { + if(husart->State == HAL_USART_STATE_BUSY_RX) + { + USART_Receive_IT(husart); + } + else + { + USART_TransmitReceive_IT(husart); + } + } + + /* USART in mode Transmitter -----------------------------------------------*/ + if((__HAL_USART_GET_IT(husart, USART_IT_TXE) != RESET) &&(__HAL_USART_GET_IT_SOURCE(husart, USART_IT_TXE) != RESET)) + { + if(husart->State == HAL_USART_STATE_BUSY_TX) + { + USART_Transmit_IT(husart); + } + else + { + USART_TransmitReceive_IT(husart); + } + } + + /* USART in mode Transmitter (transmission end) -----------------------------*/ + if((__HAL_USART_GET_IT(husart, USART_IT_TC) != RESET) &&(__HAL_USART_GET_IT_SOURCE(husart, USART_IT_TC) != RESET)) + { + USART_EndTransmit_IT(husart); + } + +} + +/** + * @brief Tx Transfer completed callback. + * @param husart: USART handle. + * @retval None + */ +__weak void HAL_USART_TxCpltCallback(USART_HandleTypeDef *husart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_USART_TxCpltCallback can be implemented in the user file. + */ +} + +/** + * @brief Tx Half Transfer completed callback. + * @param husart: USART handle. + * @retval None + */ + __weak void HAL_USART_TxHalfCpltCallback(USART_HandleTypeDef *husart) +{ + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_USART_TxHalfCpltCallback can be implemented in the user file. + */ +} + +/** + * @brief Rx Transfer completed callback. + * @param husart: USART handle. + * @retval None + */ +__weak void HAL_USART_RxCpltCallback(USART_HandleTypeDef *husart) +{ + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_USART_RxCpltCallback can be implemented in the user file. + */ +} + +/** + * @brief Rx Half Transfer completed callback. + * @param husart: USART handle. + * @retval None + */ +__weak void HAL_USART_RxHalfCpltCallback(USART_HandleTypeDef *husart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_USART_RxHalfCpltCallback can be implemented in the user file + */ +} + +/** + * @brief Tx/Rx Transfers completed callback for the non-blocking process. + * @param husart: USART handle. + * @retval None + */ +__weak void HAL_USART_TxRxCpltCallback(USART_HandleTypeDef *husart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_USART_TxRxCpltCallback can be implemented in the user file + */ +} + +/** + * @brief USART error callback. + * @param husart: USART handle. + * @retval None + */ +__weak void HAL_USART_ErrorCallback(USART_HandleTypeDef *husart) +{ + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_USART_ErrorCallback can be implemented in the user file. + */ +} + +/** + * @} + */ + +/** @defgroup USART_Exported_Functions_Group4 Peripheral State and Error functions + * @brief USART Peripheral State and Error functions + * +@verbatim + ============================================================================== + ##### Peripheral State and Error functions ##### + ============================================================================== + [..] + This subsection provides functions allowing to : + (+) Return the USART handle state + (+) Return the USART handle error code + +@endverbatim + * @{ + */ + + +/** + * @brief Return the USART handle state. + * @param husart : pointer to a USART_HandleTypeDef structure that contains + * the configuration information for the specified USART. + * @retval USART handle state + */ +HAL_USART_StateTypeDef HAL_USART_GetState(USART_HandleTypeDef *husart) +{ + return husart->State; +} + +/** + * @brief Return the USART error code. + * @param husart : pointer to a USART_HandleTypeDef structure that contains + * the configuration information for the specified USART. + * @retval USART handle Error Code + */ +uint32_t HAL_USART_GetError(USART_HandleTypeDef *husart) +{ + return husart->ErrorCode; +} + +/** + * @} + */ + +/** + * @} + */ + +/** @defgroup USART_Private_Functions USART Private Functions + * @{ + */ + +/** + * @brief DMA USART transmit process complete callback. + * @param hdma: DMA handle. + * @retval None + */ +static void USART_DMATransmitCplt(DMA_HandleTypeDef *hdma) +{ + USART_HandleTypeDef* husart = ( USART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + + /* DMA Normal mode */ + if ( HAL_IS_BIT_CLR(hdma->Instance->CCR, DMA_CCR_CIRC) ) + { + husart->TxXferCount = 0; + + if(husart->State == HAL_USART_STATE_BUSY_TX) + { + /* Disable the DMA transfer for transmit request by resetting the DMAT bit + in the USART CR3 register */ + husart->Instance->CR3 &= ~(USART_CR3_DMAT); + + /* Enable the USART Transmit Complete Interrupt */ + __HAL_USART_ENABLE_IT(husart, USART_IT_TC); + } + } + /* DMA Circular mode */ + else + { + if(husart->State == HAL_USART_STATE_BUSY_TX) + { + HAL_USART_TxCpltCallback(husart); + } + } +} + + +/** + * @brief DMA USART transmit process half complete callback. + * @param hdma : DMA handle. + * @retval None + */ +static void USART_DMATxHalfCplt(DMA_HandleTypeDef *hdma) +{ + USART_HandleTypeDef* husart = (USART_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + HAL_USART_TxHalfCpltCallback(husart); +} + +/** + * @brief DMA USART receive process complete callback. + * @param hdma: DMA handle. + * @retval None + */ +static void USART_DMAReceiveCplt(DMA_HandleTypeDef *hdma) +{ + USART_HandleTypeDef* husart = ( USART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + + /* DMA Normal mode */ + if ( HAL_IS_BIT_CLR(hdma->Instance->CCR, DMA_CCR_CIRC) ) + { + husart->RxXferCount = 0; + + /* Disable the DMA RX transfer for the receiver request by resetting the DMAR bit + in USART CR3 register */ + husart->Instance->CR3 &= (uint32_t)~((uint32_t)USART_CR3_DMAR); + /* similarly, disable the DMA TX transfer that was started to provide the + clock to the slave device */ + husart->Instance->CR3 &= (uint32_t)~((uint32_t)USART_CR3_DMAT); + + if(husart->State == HAL_USART_STATE_BUSY_RX) + { + HAL_USART_RxCpltCallback(husart); + } + /* The USART state is HAL_USART_STATE_BUSY_TX_RX */ + else + { + HAL_USART_TxRxCpltCallback(husart); + } + husart->State= HAL_USART_STATE_READY; + } + /* DMA circular mode */ + else + { + if(husart->State == HAL_USART_STATE_BUSY_RX) + { + HAL_USART_RxCpltCallback(husart); + } + /* The USART state is HAL_USART_STATE_BUSY_TX_RX */ + else + { + HAL_USART_TxRxCpltCallback(husart); + } + } + +} + +/** + * @brief DMA USART receive process half complete callback. + * @param hdma : DMA handle. + * @retval None + */ +static void USART_DMARxHalfCplt(DMA_HandleTypeDef *hdma) +{ + USART_HandleTypeDef* husart = (USART_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; + + HAL_USART_RxHalfCpltCallback(husart); +} + +/** + * @brief DMA USART communication error callback. + * @param hdma: DMA handle. + * @retval None + */ +static void USART_DMAError(DMA_HandleTypeDef *hdma) +{ + USART_HandleTypeDef* husart = ( USART_HandleTypeDef* )((DMA_HandleTypeDef* )hdma)->Parent; + + husart->RxXferCount = 0; + husart->TxXferCount = 0; + husart->ErrorCode |= HAL_USART_ERROR_DMA; + husart->State= HAL_USART_STATE_READY; + + HAL_USART_ErrorCallback(husart); +} + +/** + * @brief Handle USART Communication Timeout. + * @param husart: USART handle. + * @param Flag: specifies the USART flag to check. + * @param Status: the Flag status (SET or RESET). + * @param Timeout: timeout duration. + * @retval HAL status + */ +static HAL_StatusTypeDef USART_WaitOnFlagUntilTimeout(USART_HandleTypeDef *husart, uint32_t Flag, FlagStatus Status, uint32_t Timeout) +{ + uint32_t tickstart = HAL_GetTick(); + + /* Wait until flag is set */ + if(Status == RESET) + { + while(__HAL_USART_GET_FLAG(husart, Flag) == RESET) + { + /* Check for the Timeout */ + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0) || ((HAL_GetTick()-tickstart) > Timeout)) + { + /* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */ + __HAL_USART_DISABLE_IT(husart, USART_IT_TXE); + __HAL_USART_DISABLE_IT(husart, USART_IT_RXNE); + __HAL_USART_DISABLE_IT(husart, USART_IT_PE); + __HAL_USART_DISABLE_IT(husart, USART_IT_ERR); + + husart->State= HAL_USART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_TIMEOUT; + } + } + } + } + else + { + while(__HAL_USART_GET_FLAG(husart, Flag) != RESET) + { + /* Check for the Timeout */ + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0) || ((HAL_GetTick()-tickstart) > Timeout)) + { + /* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */ + __HAL_USART_DISABLE_IT(husart, USART_IT_TXE); + __HAL_USART_DISABLE_IT(husart, USART_IT_RXNE); + __HAL_USART_DISABLE_IT(husart, USART_IT_PE); + __HAL_USART_DISABLE_IT(husart, USART_IT_ERR); + + husart->State= HAL_USART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_TIMEOUT; + } + } + } + } + return HAL_OK; +} + +/** + * @brief Configure the USART peripheral. + * @param husart: USART handle. + * @retval HAL status + */ +static HAL_StatusTypeDef USART_SetConfig(USART_HandleTypeDef *husart) +{ + uint32_t tmpreg = 0x0; + USART_ClockSourceTypeDef clocksource = USART_CLOCKSOURCE_UNDEFINED; + HAL_StatusTypeDef ret = HAL_OK; + uint16_t brrtemp = 0x0000; + uint16_t usartdiv = 0x0000; + + /* Check the parameters */ + assert_param(IS_USART_POLARITY(husart->Init.CLKPolarity)); + assert_param(IS_USART_PHASE(husart->Init.CLKPhase)); + assert_param(IS_USART_LASTBIT(husart->Init.CLKLastBit)); + assert_param(IS_USART_BAUDRATE(husart->Init.BaudRate)); + assert_param(IS_USART_WORD_LENGTH(husart->Init.WordLength)); + assert_param(IS_USART_STOPBITS(husart->Init.StopBits)); + assert_param(IS_USART_PARITY(husart->Init.Parity)); + assert_param(IS_USART_MODE(husart->Init.Mode)); + + + /*-------------------------- USART CR1 Configuration -----------------------*/ + /* Clear M, PCE, PS, TE and RE bits and configure + * the USART Word Length, Parity and Mode: + * set the M bits according to husart->Init.WordLength value + * set PCE and PS bits according to husart->Init.Parity value + * set TE and RE bits according to husart->Init.Mode value + * force OVER8 to 1 to allow to reach the maximum speed (Fclock/8) */ + tmpreg = (uint32_t)husart->Init.WordLength | husart->Init.Parity | husart->Init.Mode | USART_CR1_OVER8; + MODIFY_REG(husart->Instance->CR1, USART_CR1_FIELDS, tmpreg); + + /*---------------------------- USART CR2 Configuration ---------------------*/ + /* Clear and configure the USART Clock, CPOL, CPHA, LBCL and STOP bits: + * set CPOL bit according to husart->Init.CLKPolarity value + * set CPHA bit according to husart->Init.CLKPhase value + * set LBCL bit according to husart->Init.CLKLastBit value + * set STOP[13:12] bits according to husart->Init.StopBits value */ + tmpreg = (uint32_t)(USART_CLOCK_ENABLE); + tmpreg |= ((uint32_t)husart->Init.CLKPolarity | (uint32_t)husart->Init.CLKPhase); + tmpreg |= ((uint32_t)husart->Init.CLKLastBit | (uint32_t)husart->Init.StopBits); + MODIFY_REG(husart->Instance->CR2, USART_CR2_FIELDS, tmpreg); + + /*-------------------------- USART CR3 Configuration -----------------------*/ + /* no CR3 register configuration */ + + /*-------------------------- USART BRR Configuration -----------------------*/ + /* BRR is filled-up according to OVER8 bit setting which is forced to 1 */ + USART_GETCLOCKSOURCE(husart, clocksource); + switch (clocksource) + { + case USART_CLOCKSOURCE_PCLK1: + usartdiv = (uint16_t)((2*HAL_RCC_GetPCLK1Freq()) / husart->Init.BaudRate); + break; + case USART_CLOCKSOURCE_PCLK2: + usartdiv = (uint16_t)((2*HAL_RCC_GetPCLK2Freq()) / husart->Init.BaudRate); + break; + case USART_CLOCKSOURCE_HSI: + usartdiv = (uint16_t)((2*HSI_VALUE) / husart->Init.BaudRate); + break; + case USART_CLOCKSOURCE_SYSCLK: + usartdiv = (uint16_t)((2*HAL_RCC_GetSysClockFreq()) / husart->Init.BaudRate); + break; + case USART_CLOCKSOURCE_LSE: + usartdiv = (uint16_t)((2*LSE_VALUE) / husart->Init.BaudRate); + break; + case USART_CLOCKSOURCE_UNDEFINED: + default: + ret = HAL_ERROR; + break; + } + + brrtemp = usartdiv & 0xFFF0; + brrtemp |= (uint16_t)((usartdiv & (uint16_t)0x000F) >> 1U); + husart->Instance->BRR = brrtemp; + + return ret; +} + +/** + * @brief Check the USART Idle State. + * @param husart: USART handle. + * @retval HAL status + */ +static HAL_StatusTypeDef USART_CheckIdleState(USART_HandleTypeDef *husart) +{ + /* Initialize the USART ErrorCode */ + husart->ErrorCode = HAL_USART_ERROR_NONE; + + /* Check if the Transmitter is enabled */ + if((husart->Instance->CR1 & USART_CR1_TE) == USART_CR1_TE) + { + /* Wait until TEACK flag is set */ + if(USART_WaitOnFlagUntilTimeout(husart, USART_ISR_TEACK, RESET, USART_TEACK_REACK_TIMEOUT) != HAL_OK) + { + /* Timeout occurred */ + return HAL_TIMEOUT; + } + } + /* Check if the Receiver is enabled */ + if((husart->Instance->CR1 & USART_CR1_RE) == USART_CR1_RE) + { + /* Wait until REACK flag is set */ + if(USART_WaitOnFlagUntilTimeout(husart, USART_ISR_REACK, RESET, USART_TEACK_REACK_TIMEOUT) != HAL_OK) + { + /* Timeout occurred */ + return HAL_TIMEOUT; + } + } + + /* Initialize the USART state*/ + husart->State= HAL_USART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(husart); + + return HAL_OK; +} + +/** + * @brief Simplex send an amount of data in non-blocking mode. + * @note Function called under interruption only, once + * interruptions have been enabled by HAL_USART_Transmit_IT(). + * @note The USART errors are not managed to avoid the overrun error. + * @param husart: USART handle. + * @retval HAL status + */ +static HAL_StatusTypeDef USART_Transmit_IT(USART_HandleTypeDef *husart) +{ + uint16_t* tmp; + + if(husart->State == HAL_USART_STATE_BUSY_TX) + { + + if(husart->TxXferCount == 0) + { + /* Disable the USART Transmit Complete Interrupt */ + __HAL_USART_DISABLE_IT(husart, USART_IT_TXE); + + /* Enable the USART Transmit Complete Interrupt */ + __HAL_USART_ENABLE_IT(husart, USART_IT_TC); + + return HAL_OK; + } + else + { + if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) + { + tmp = (uint16_t*) husart->pTxBuffPtr; + husart->Instance->TDR = (*tmp & (uint16_t)0x01FF); + husart->pTxBuffPtr += 2; + } + else + { + husart->Instance->TDR = (uint8_t)(*husart->pTxBuffPtr++ & (uint8_t)0xFF); + } + + husart->TxXferCount--; + + return HAL_OK; + } + } + else + { + return HAL_BUSY; + } +} + + +/** + * @brief Wraps up transmission in non-blocking mode. + * @param husart: pointer to a USART_HandleTypeDef structure that contains + * the configuration information for the specified USART module. + * @retval HAL status + */ +static HAL_StatusTypeDef USART_EndTransmit_IT(USART_HandleTypeDef *husart) +{ + /* Disable the USART Transmit Complete Interrupt */ + __HAL_USART_DISABLE_IT(husart, USART_IT_TC); + + /* Disable the USART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_USART_DISABLE_IT(husart, USART_IT_ERR); + + husart->State = HAL_USART_STATE_READY; + + HAL_USART_TxCpltCallback(husart); + + return HAL_OK; +} + + +/** + * @brief Simplex receive an amount of data in non-blocking mode. + * @note Function called under interruption only, once + * interruptions have been enabled by HAL_USART_Receive_IT(). + * @param husart: USART handle + * @retval HAL status + */ +static HAL_StatusTypeDef USART_Receive_IT(USART_HandleTypeDef *husart) +{ + uint16_t* tmp; + uint16_t uhMask = husart->Mask; + + if(husart->State == HAL_USART_STATE_BUSY_RX) + { + + if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) + { + tmp = (uint16_t*) husart->pRxBuffPtr; + *tmp = (uint16_t)(husart->Instance->RDR & uhMask); + husart->pRxBuffPtr += 2; + } + else + { + *husart->pRxBuffPtr++ = (uint8_t)(husart->Instance->RDR & (uint8_t)uhMask); + } + /* Send dummy byte in order to generate the clock for the Slave to Send the next data */ + husart->Instance->TDR = (USART_DUMMY_DATA & (uint16_t)0x00FF); + + if(--husart->RxXferCount == 0) + { + __HAL_USART_DISABLE_IT(husart, USART_IT_RXNE); + + /* Disable the USART Parity Error Interrupt */ + __HAL_USART_DISABLE_IT(husart, USART_IT_PE); + + /* Disable the USART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_USART_DISABLE_IT(husart, USART_IT_ERR); + + husart->State = HAL_USART_STATE_READY; + + HAL_USART_RxCpltCallback(husart); + + return HAL_OK; + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Full-Duplex Send receive an amount of data in full-duplex mode (non-blocking). + * @note Function called under interruption only, once + * interruptions have been enabled by HAL_USART_TransmitReceive_IT(). + * @param husart: USART handle. + * @retval HAL status + */ +static HAL_StatusTypeDef USART_TransmitReceive_IT(USART_HandleTypeDef *husart) +{ + uint16_t* tmp; + uint16_t uhMask = husart->Mask; + + if(husart->State == HAL_USART_STATE_BUSY_TX_RX) + { + + if(husart->TxXferCount != 0x00) + { + if(__HAL_USART_GET_FLAG(husart, USART_FLAG_TXE) != RESET) + { + if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) + { + tmp = (uint16_t*) husart->pTxBuffPtr; + husart->Instance->TDR = (uint16_t)(*tmp & uhMask); + husart->pTxBuffPtr += 2; + } + else + { + husart->Instance->TDR = (uint8_t)(*husart->pTxBuffPtr++ & (uint8_t)uhMask); + } + husart->TxXferCount--; + + /* Check the latest data transmitted */ + if(husart->TxXferCount == 0) + { + __HAL_USART_DISABLE_IT(husart, USART_IT_TXE); + } + } + } + + if(husart->RxXferCount != 0x00) + { + if(__HAL_USART_GET_FLAG(husart, USART_FLAG_RXNE) != RESET) + { + if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) + { + tmp = (uint16_t*) husart->pRxBuffPtr; + *tmp = (uint16_t)(husart->Instance->RDR & uhMask); + husart->pRxBuffPtr += 2; + } + else + { + *husart->pRxBuffPtr++ = (uint8_t)(husart->Instance->RDR & (uint8_t)uhMask); + } + husart->RxXferCount--; + } + } + + /* Check the latest data received */ + if(husart->RxXferCount == 0) + { + __HAL_USART_DISABLE_IT(husart, USART_IT_RXNE); + + /* Disable the USART Parity Error Interrupt */ + __HAL_USART_DISABLE_IT(husart, USART_IT_PE); + + /* Disable the USART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_USART_DISABLE_IT(husart, USART_IT_ERR); + + husart->State = HAL_USART_STATE_READY; + + HAL_USART_TxRxCpltCallback(husart); + + return HAL_OK; + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @} + */ + +#endif /* HAL_USART_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/