fix LPC812 PWM
Fork of mbed-dev by
api/Ethernet.h
- Committer:
- nameless129
- Date:
- 2016-05-16
- Revision:
- 129:2e517c56bcfb
- Parent:
- 0:9b334a45a8ff
File content as of revision 129:2e517c56bcfb:
/* mbed Microcontroller Library * Copyright (c) 2006-2013 ARM Limited * * Licensed under the Apache License, Version 2.0 (the "License"); * you may not use this file except in compliance with the License. * You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. */ #ifndef MBED_ETHERNET_H #define MBED_ETHERNET_H #include "platform.h" #if DEVICE_ETHERNET namespace mbed { /** An ethernet interface, to use with the ethernet pins. * * Example: * @code * // Read destination and source from every ethernet packet * * #include "mbed.h" * * Ethernet eth; * * int main() { * char buf[0x600]; * * while(1) { * int size = eth.receive(); * if(size > 0) { * eth.read(buf, size); * printf("Destination: %02X:%02X:%02X:%02X:%02X:%02X\n", * buf[0], buf[1], buf[2], buf[3], buf[4], buf[5]); * printf("Source: %02X:%02X:%02X:%02X:%02X:%02X\n", * buf[6], buf[7], buf[8], buf[9], buf[10], buf[11]); * } * * wait(1); * } * } * @endcode */ class Ethernet { public: /** Initialise the ethernet interface. */ Ethernet(); /** Powers the hardware down. */ virtual ~Ethernet(); enum Mode { AutoNegotiate, HalfDuplex10, FullDuplex10, HalfDuplex100, FullDuplex100 }; /** Writes into an outgoing ethernet packet. * * It will append size bytes of data to the previously written bytes. * * @param data An array to write. * @param size The size of data. * * @returns * The number of written bytes. */ int write(const char *data, int size); /** Send an outgoing ethernet packet. * * After filling in the data in an ethernet packet it must be send. * Send will provide a new packet to write to. * * @returns * 0 if the sending was failed, * or the size of the packet successfully sent. */ int send(); /** Recevies an arrived ethernet packet. * * Receiving an ethernet packet will drop the last received ethernet packet * and make a new ethernet packet ready to read. * If no ethernet packet is arrived it will return 0. * * @returns * 0 if no ethernet packet is arrived, * or the size of the arrived packet. */ int receive(); /** Read from an recevied ethernet packet. * * After receive returnd a number bigger than 0it is * possible to read bytes from this packet. * Read will write up to size bytes into data. * * It is possible to use read multible times. * Each time read will start reading after the last read byte before. * * @returns * The number of byte read. */ int read(char *data, int size); /** Gives the ethernet address of the mbed. * * @param mac Must be a pointer to a 6 byte char array to copy the ethernet address in. */ void address(char *mac); /** Returns if an ethernet link is pressent or not. It takes a wile after Ethernet initializion to show up. * * @returns * 0 if no ethernet link is pressent, * 1 if an ethernet link is pressent. * * Example: * @code * // Using the Ethernet link function * #include "mbed.h" * * Ethernet eth; * * int main() { * wait(1); // Needed after startup. * if (eth.link()) { * printf("online\n"); * } else { * printf("offline\n"); * } * } * @endcode */ int link(); /** Sets the speed and duplex parameters of an ethernet link * * - AutoNegotiate Auto negotiate speed and duplex * - HalfDuplex10 10 Mbit, half duplex * - FullDuplex10 10 Mbit, full duplex * - HalfDuplex100 100 Mbit, half duplex * - FullDuplex100 100 Mbit, full duplex * * @param mode the speed and duplex mode to set the link to: */ void set_link(Mode mode); }; } // namespace mbed #endif #endif