Tobias Naegeli / Mbed 2 deprecated AIT_UWB_Range

Tobi's ubw test branch

Dependencies:   mavlink_bridge mbed

Fork of AIT_UWB_Range by Benjamin Hepp

DW1000/DW1000.cpp@15:e1fea7e2aff1, 2014-11-23 (annotated)

Committer:
manumaet
Date:
Sun Nov 23 20:45:14 2014 +0000
Revision:
15:e1fea7e2aff1
Parent:
13:b4d27bf7062a
Child:
17:8afa5f9122da
sending of 1020 chars in one frame worked

Who changed what in which revision?

UserRevisionLine numberNew contents of line
manumaet 0:f50e671ffff7 1 #include "DW1000.h"
manumaet 0:f50e671ffff7 2
manumaet 8:7a9c61242e2f 3 DW1000::DW1000(PinName MOSI, PinName MISO, PinName SCLK, PinName CS, PinName IRQ) : spi(MOSI, MISO, SCLK), cs(CS), irq(IRQ) {
manumaet 0:f50e671ffff7 4 deselect(); // Chip must be deselected first
manumaet 0:f50e671ffff7 5 spi.format(8,0); // Setup the spi for standard 8 bit data and SPI-Mode 0 (GPIO5, GPIO6 open circuit or ground on DW1000)
manumaet 0:f50e671ffff7 6 spi.frequency(1000000); // with a 1MHz clock rate (worked up to 49MHz in our Test)
manumaet 7:e634eeafc4d2 7
manumaet 12:985aa9843c3c 8 //resetAll(); // we can do a soft reset if we want to (only needed for debugging)
manumaet 12:985aa9843c3c 9 loadLDE(); // important everytime DW1000 initialises/awakes otherwise the LDE algorithm must be turned of or there's receiving malfunction see User Manual LDELOAD on p22 & p158
manumaet 12:985aa9843c3c 10 writeRegister8(DW1000_SYS_CFG, 3, 0x20); // enable auto reenabling receiver after error
manumaet 15:e1fea7e2aff1 11 writeRegister8(DW1000_SYS_CFG, 2, 0x03); // enable 1024 byte frames TODO: doesn't work!!
manumaet 11:c87d37db2c6f 12
manumaet 8:7a9c61242e2f 13 irq.rise(this, &DW1000::ISR); // attach Interrupt handler to rising edge
manumaet 0:f50e671ffff7 14 }
manumaet 0:f50e671ffff7 15
manumaet 0:f50e671ffff7 16 uint32_t DW1000::getDeviceID() {
manumaet 0:f50e671ffff7 17 uint32_t result;
manumaet 0:f50e671ffff7 18 readRegister(DW1000_DEV_ID, 0, (uint8_t*)&result, 4);
manumaet 0:f50e671ffff7 19 return result;
manumaet 0:f50e671ffff7 20 }
manumaet 0:f50e671ffff7 21
manumaet 0:f50e671ffff7 22 uint64_t DW1000::getEUI() {
manumaet 0:f50e671ffff7 23 uint64_t result;
manumaet 0:f50e671ffff7 24 readRegister(DW1000_EUI, 0, (uint8_t*)&result, 8);
manumaet 0:f50e671ffff7 25 return result;
manumaet 0:f50e671ffff7 26 }
manumaet 0:f50e671ffff7 27
manumaet 0:f50e671ffff7 28 void DW1000::setEUI(uint64_t EUI) {
manumaet 0:f50e671ffff7 29 writeRegister(DW1000_EUI, 0, (uint8_t*)&EUI, 8);
manumaet 0:f50e671ffff7 30 }
manumaet 0:f50e671ffff7 31
manumaet 0:f50e671ffff7 32 float DW1000::getVoltage() {
manumaet 12:985aa9843c3c 33 uint8_t buffer[7] = {0x80, 0x0A, 0x0F, 0x01, 0x00}; // algorithm form User Manual p57
manumaet 0:f50e671ffff7 34 writeRegister(DW1000_RF_CONF, 0x11, buffer, 2);
manumaet 0:f50e671ffff7 35 writeRegister(DW1000_RF_CONF, 0x12, &buffer[2], 1);
manumaet 0:f50e671ffff7 36 writeRegister(DW1000_TX_CAL, 0x00, &buffer[3], 1);
manumaet 0:f50e671ffff7 37 writeRegister(DW1000_TX_CAL, 0x00, &buffer[4], 1);
manumaet 8:7a9c61242e2f 38 readRegister(DW1000_TX_CAL, 0x03, &buffer[5], 2); // get the 8-Bit readings for Voltage and Temperature
manumaet 0:f50e671ffff7 39 float Voltage = buffer[5] * 0.0057 + 2.3;
manumaet 8:7a9c61242e2f 40 float Temperature = buffer[6] * 1.13 - 113.0; // TODO: getTemperature was always ~35 degree with better formula/calibration see instance_common.c row 391
manumaet 0:f50e671ffff7 41 return Voltage;
manumaet 0:f50e671ffff7 42 }
manumaet 0:f50e671ffff7 43
manumaet 10:d077bb12d259 44 void DW1000::sendString(char* message) {
manumaet 10:d077bb12d259 45 sendFrame((uint8_t*)message, strlen(message)+1);
manumaet 10:d077bb12d259 46 }
manumaet 10:d077bb12d259 47
manumaet 10:d077bb12d259 48 char* DW1000::receiveString() {
manumaet 10:d077bb12d259 49 uint16_t framelength = 0; // get framelength
manumaet 10:d077bb12d259 50 readRegister(DW1000_RX_FINFO, 0, (uint8_t*)&framelength, 2);
manumaet 10:d077bb12d259 51 framelength = (framelength & 0x03FF) - 2; // take only the right bits and subtract the 2 CRC Bytes
manumaet 10:d077bb12d259 52 char* receive = new char[framelength]; // get data from buffer
manumaet 10:d077bb12d259 53 readRegister(DW1000_RX_BUFFER, 0, (uint8_t*)receive, framelength);
manumaet 10:d077bb12d259 54 return receive;
manumaet 10:d077bb12d259 55 }
manumaet 10:d077bb12d259 56
manumaet 11:c87d37db2c6f 57 void DW1000::sendFrame(uint8_t* message, uint16_t length) {
manumaet 13:b4d27bf7062a 58 writeRegister8(DW1000_SYS_CTRL, 0, 0x40); // disable tranceiver go back to idle mode TODO: only if receiving!!
manumaet 13:b4d27bf7062a 59 writeRegister(DW1000_TX_BUFFER, 0, message, length); // fill buffer
manumaet 7:e634eeafc4d2 60
manumaet 13:b4d27bf7062a 61 uint8_t backup = readRegister8(DW1000_TX_FCTRL, 1); // put length of frame including 2 CRC Bytes
manumaet 13:b4d27bf7062a 62 length += 2;
manumaet 11:c87d37db2c6f 63 length = ((backup & 0xFC) << 8) | (length & 0x03FF);
manumaet 7:e634eeafc4d2 64
manumaet 11:c87d37db2c6f 65 writeRegister(DW1000_TX_FCTRL, 0, (uint8_t*)&length, 2); // TODO: make that bigger frames than 256 can be sent
manumaet 11:c87d37db2c6f 66
manumaet 11:c87d37db2c6f 67 writeRegister8(DW1000_SYS_CTRL, 0, 0x02); // trigger sending process by setting the TXSTRT bit
manumaet 13:b4d27bf7062a 68 receiveFrame(); // TODO: only if receiving!!
manumaet 8:7a9c61242e2f 69 }
manumaet 8:7a9c61242e2f 70
manumaet 8:7a9c61242e2f 71 void DW1000::receiveFrame() {
manumaet 13:b4d27bf7062a 72 writeRegister8(DW1000_SYS_CTRL, 0x01, 0x01); // start listening for preamble by setting the RXENAB bit
manumaet 7:e634eeafc4d2 73 }
manumaet 7:e634eeafc4d2 74
manumaet 7:e634eeafc4d2 75 void DW1000::ISR() {
manumaet 12:985aa9843c3c 76 uint64_t status; // get the entire system status
manumaet 12:985aa9843c3c 77 readRegister(DW1000_SYS_STATUS, 0, (uint8_t*)&status, 5);
manumaet 12:985aa9843c3c 78 status &= 0xFFFFFFFFFF; // only 40-Bit
manumaet 12:985aa9843c3c 79 if (status & 0x4000)
manumaet 12:985aa9843c3c 80 callbackRX();
manumaet 12:985aa9843c3c 81 if (status & 0x80)
manumaet 12:985aa9843c3c 82 ;//callbackTX(); // TODO: mask TX done interrupt make TX handler
manumaet 7:e634eeafc4d2 83 }
manumaet 7:e634eeafc4d2 84
manumaet 12:985aa9843c3c 85 void DW1000::loadLDE() {
manumaet 12:985aa9843c3c 86 uint16_t ldeload[] = {0x0301, 0x8000, 0x0200}; // initialise LDE algorithm LDELOAD User Manual p22
manumaet 12:985aa9843c3c 87 writeRegister(DW1000_PMSC, 0, (uint8_t*)&ldeload[0], 2); // set clock to XTAL so OTP is reliable
manumaet 12:985aa9843c3c 88 writeRegister(DW1000_OTP_IF, 0x06, (uint8_t*)&ldeload[1], 2); // set LDELOAD bit in OTP
manumaet 12:985aa9843c3c 89 wait_us(150);
manumaet 12:985aa9843c3c 90 writeRegister(DW1000_PMSC, 0, (uint8_t*)&ldeload[2], 2); // recover to PLL clock
manumaet 12:985aa9843c3c 91 }
manumaet 12:985aa9843c3c 92
manumaet 12:985aa9843c3c 93 void DW1000::resetRX() {
manumaet 12:985aa9843c3c 94 writeRegister8(DW1000_PMSC, 3, 0xE0); // set RX reset
manumaet 12:985aa9843c3c 95 writeRegister8(DW1000_PMSC, 3, 0xF0); // clear RX reset
manumaet 12:985aa9843c3c 96 }
manumaet 12:985aa9843c3c 97
manumaet 12:985aa9843c3c 98 void DW1000::resetAll() {
manumaet 12:985aa9843c3c 99 writeRegister8(DW1000_PMSC, 0, 0x01); // set clock to XTAL
manumaet 12:985aa9843c3c 100 writeRegister8(DW1000_PMSC, 3, 0x00); // set All reset
manumaet 12:985aa9843c3c 101 wait_us(10); // wait for PLL to lock
manumaet 12:985aa9843c3c 102 writeRegister8(DW1000_PMSC, 3, 0xF0); // clear All reset
manumaet 7:e634eeafc4d2 103 }
manumaet 0:f50e671ffff7 104
manumaet 0:f50e671ffff7 105 // SPI Interface ------------------------------------------------------------------------------------
manumaet 10:d077bb12d259 106 uint8_t DW1000::readRegister8(uint8_t reg, uint16_t subaddress) {
manumaet 10:d077bb12d259 107 uint8_t result;
manumaet 10:d077bb12d259 108 readRegister(reg, subaddress, &result, 1);
manumaet 10:d077bb12d259 109 return result;
manumaet 10:d077bb12d259 110 }
manumaet 10:d077bb12d259 111
manumaet 8:7a9c61242e2f 112 void DW1000::writeRegister8(uint8_t reg, uint16_t subaddress, uint8_t buffer) {
manumaet 8:7a9c61242e2f 113 writeRegister(reg, subaddress, &buffer, 1);
manumaet 8:7a9c61242e2f 114 }
manumaet 8:7a9c61242e2f 115
manumaet 8:7a9c61242e2f 116 void DW1000::readRegister(uint8_t reg, uint16_t subaddress, uint8_t *buffer, int length) {
manumaet 0:f50e671ffff7 117 setupTransaction(reg, subaddress, false);
manumaet 8:7a9c61242e2f 118 for(int i=0; i<length; i++) // get data
manumaet 0:f50e671ffff7 119 buffer[i] = spi.write(0x00);
manumaet 0:f50e671ffff7 120 deselect();
manumaet 0:f50e671ffff7 121 }
manumaet 0:f50e671ffff7 122
manumaet 8:7a9c61242e2f 123 void DW1000::writeRegister(uint8_t reg, uint16_t subaddress, uint8_t *buffer, int length) {
manumaet 0:f50e671ffff7 124 setupTransaction(reg, subaddress, true);
manumaet 8:7a9c61242e2f 125 for(int i=0; i<length; i++) // put data
manumaet 0:f50e671ffff7 126 spi.write(buffer[i]);
manumaet 0:f50e671ffff7 127 deselect();
manumaet 0:f50e671ffff7 128 }
manumaet 0:f50e671ffff7 129
manumaet 8:7a9c61242e2f 130 void DW1000::setupTransaction(uint8_t reg, uint16_t subaddress, bool write) {
manumaet 0:f50e671ffff7 131 reg |= (write * DW1000_WRITE_FLAG);
manumaet 0:f50e671ffff7 132 select();
manumaet 0:f50e671ffff7 133 if (subaddress > 0) { // there's a subadress, we need to set flag and send second header byte
manumaet 0:f50e671ffff7 134 spi.write(reg | DW1000_SUBADDRESS_FLAG);
manumaet 0:f50e671ffff7 135 if (subaddress > 127) { // sub address too long, we need to set flag and send third header byte
manumaet 0:f50e671ffff7 136 spi.write((uint8_t)(subaddress & 0x7F) | DW1000_2_SUBADDRESS_FLAG);
manumaet 0:f50e671ffff7 137 spi.write((uint8_t)(subaddress >> 7));
manumaet 0:f50e671ffff7 138 } else {
manumaet 0:f50e671ffff7 139 spi.write((uint8_t)subaddress);
manumaet 0:f50e671ffff7 140 }
manumaet 0:f50e671ffff7 141 } else {
manumaet 0:f50e671ffff7 142 spi.write(reg);
manumaet 0:f50e671ffff7 143 }
manumaet 0:f50e671ffff7 144 }
manumaet 0:f50e671ffff7 145
manumaet 12:985aa9843c3c 146 void DW1000::select() { cs = 0; } // set CS low to start transmission
manumaet 12:985aa9843c3c 147 void DW1000::deselect() { cs = 1; } // set CS high to stop transmission