Diff: misc.c

Revision:

8:1c6281289d67

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/misc.c	Sun Nov 15 09:00:40 2015 +0000
@@ -0,0 +1,244 @@
+/**
+  ******************************************************************************
+  * @file    misc.c
+  * @author  MCD Application Team
+  * @version V1.0.0
+  * @date    30-September-2011
+  * @brief   This file provides all the miscellaneous firmware functions (add-on
+  *          to CMSIS functions).
+  *          
+  *  @verbatim   
+  *                               
+  *          ===================================================================      
+  *                        How to configure Interrupts using driver 
+  *          ===================================================================      
+  * 
+  *            This section provide functions allowing to configure the NVIC interrupts (IRQ).
+  *            The Cortex-M4 exceptions are managed by CMSIS functions.
+  *
+  *            1. Configure the NVIC Priority Grouping using NVIC_PriorityGroupConfig()
+  *                function according to the following table.
+ 
+  *  The table below gives the allowed values of the pre-emption priority and subpriority according
+  *  to the Priority Grouping configuration performed by NVIC_PriorityGroupConfig function
+  *    ==========================================================================================================================
+  *      NVIC_PriorityGroup   | NVIC_IRQChannelPreemptionPriority | NVIC_IRQChannelSubPriority  |       Description
+  *    ==========================================================================================================================
+  *     NVIC_PriorityGroup_0  |                0                  |            0-15             | 0 bits for pre-emption priority
+  *                           |                                   |                             | 4 bits for subpriority
+  *    --------------------------------------------------------------------------------------------------------------------------
+  *     NVIC_PriorityGroup_1  |                0-1                |            0-7              | 1 bits for pre-emption priority
+  *                           |                                   |                             | 3 bits for subpriority
+  *    --------------------------------------------------------------------------------------------------------------------------    
+  *     NVIC_PriorityGroup_2  |                0-3                |            0-3              | 2 bits for pre-emption priority
+  *                           |                                   |                             | 2 bits for subpriority
+  *    --------------------------------------------------------------------------------------------------------------------------    
+  *     NVIC_PriorityGroup_3  |                0-7                |            0-1              | 3 bits for pre-emption priority
+  *                           |                                   |                             | 1 bits for subpriority
+  *    --------------------------------------------------------------------------------------------------------------------------    
+  *     NVIC_PriorityGroup_4  |                0-15               |            0                | 4 bits for pre-emption priority
+  *                           |                                   |                             | 0 bits for subpriority                       
+  *    ==========================================================================================================================     
+  *
+  *            2. Enable and Configure the priority of the selected IRQ Channels using NVIC_Init()  
+  *
+  * @note  When the NVIC_PriorityGroup_0 is selected, IRQ pre-emption is no more possible. 
+  *        The pending IRQ priority will be managed only by the subpriority.
+  *
+  * @note  IRQ priority order (sorted by highest to lowest priority):
+  *         - Lowest pre-emption priority
+  *         - Lowest subpriority
+  *         - Lowest hardware priority (IRQ number)
+  *
+  *  @endverbatim
+  *
+  ******************************************************************************
+  * @attention
+  *
+  * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+  * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+  * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+  * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+  * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+  * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+  *
+  * <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
+  ******************************************************************************
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "misc.h"
+
+/** @addtogroup STM32F4xx_StdPeriph_Driver
+  * @{
+  */
+
+/** @defgroup MISC 
+  * @brief MISC driver modules
+  * @{
+  */
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+#define AIRCR_VECTKEY_MASK    ((uint32_t)0x05FA0000)
+
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup MISC_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Configures the priority grouping: pre-emption priority and subpriority.
+  * @param  NVIC_PriorityGroup: specifies the priority grouping bits length. 
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_PriorityGroup_0: 0 bits for pre-emption priority
+  *                                4 bits for subpriority
+  *     @arg NVIC_PriorityGroup_1: 1 bits for pre-emption priority
+  *                                3 bits for subpriority
+  *     @arg NVIC_PriorityGroup_2: 2 bits for pre-emption priority
+  *                                2 bits for subpriority
+  *     @arg NVIC_PriorityGroup_3: 3 bits for pre-emption priority
+  *                                1 bits for subpriority
+  *     @arg NVIC_PriorityGroup_4: 4 bits for pre-emption priority
+  *                                0 bits for subpriority
+  * @note   When the NVIC_PriorityGroup_0 is selected, IRQ pre-emption is no more possible. 
+  *         The pending IRQ priority will be managed only by the subpriority. 
+  * @retval None
+  */
+void NVIC_PriorityGroupConfig(uint32_t NVIC_PriorityGroup)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_PRIORITY_GROUP(NVIC_PriorityGroup));
+  
+  /* Set the PRIGROUP[10:8] bits according to NVIC_PriorityGroup value */
+  SCB->AIRCR = AIRCR_VECTKEY_MASK | NVIC_PriorityGroup;
+}
+
+/**
+  * @brief  Initializes the NVIC peripheral according to the specified
+  *         parameters in the NVIC_InitStruct.
+  * @note   To configure interrupts priority correctly, the NVIC_PriorityGroupConfig()
+  *         function should be called before. 
+  * @param  NVIC_InitStruct: pointer to a NVIC_InitTypeDef structure that contains
+  *         the configuration information for the specified NVIC peripheral.
+  * @retval None
+  */
+void NVIC_Init(NVIC_InitTypeDef* NVIC_InitStruct)
+{
+  uint8_t tmppriority = 0x00, tmppre = 0x00, tmpsub = 0x0F;
+  
+  /* Check the parameters */
+  assert_param(IS_FUNCTIONAL_STATE(NVIC_InitStruct->NVIC_IRQChannelCmd));
+  assert_param(IS_NVIC_PREEMPTION_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority));  
+  assert_param(IS_NVIC_SUB_PRIORITY(NVIC_InitStruct->NVIC_IRQChannelSubPriority));
+    
+  if (NVIC_InitStruct->NVIC_IRQChannelCmd != DISABLE)
+  {
+    /* Compute the Corresponding IRQ Priority --------------------------------*/    
+    tmppriority = (0x700 - ((SCB->AIRCR) & (uint32_t)0x700))>> 0x08;
+    tmppre = (0x4 - tmppriority);
+    tmpsub = tmpsub >> tmppriority;
+
+    tmppriority = NVIC_InitStruct->NVIC_IRQChannelPreemptionPriority << tmppre;
+    tmppriority |=  (uint8_t)(NVIC_InitStruct->NVIC_IRQChannelSubPriority & tmpsub);
+        
+    tmppriority = tmppriority << 0x04;
+        
+    NVIC->IP[NVIC_InitStruct->NVIC_IRQChannel] = tmppriority;
+    
+    /* Enable the Selected IRQ Channels --------------------------------------*/
+    NVIC->ISER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] =
+      (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F);
+  }
+  else
+  {
+    /* Disable the Selected IRQ Channels -------------------------------------*/
+    NVIC->ICER[NVIC_InitStruct->NVIC_IRQChannel >> 0x05] =
+      (uint32_t)0x01 << (NVIC_InitStruct->NVIC_IRQChannel & (uint8_t)0x1F);
+  }
+}
+
+/**
+  * @brief  Sets the vector table location and Offset.
+  * @param  NVIC_VectTab: specifies if the vector table is in RAM or FLASH memory.
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_VectTab_RAM: Vector Table in internal SRAM.
+  *     @arg NVIC_VectTab_FLASH: Vector Table in internal FLASH.
+  * @param  Offset: Vector Table base offset field. This value must be a multiple of 0x200.
+  * @retval None
+  */
+void NVIC_SetVectorTable(uint32_t NVIC_VectTab, uint32_t Offset)
+{ 
+  /* Check the parameters */
+  assert_param(IS_NVIC_VECTTAB(NVIC_VectTab));
+  assert_param(IS_NVIC_OFFSET(Offset));  
+   
+  SCB->VTOR = NVIC_VectTab | (Offset & (uint32_t)0x1FFFFF80);
+}
+
+/**
+  * @brief  Selects the condition for the system to enter low power mode.
+  * @param  LowPowerMode: Specifies the new mode for the system to enter low power mode.
+  *   This parameter can be one of the following values:
+  *     @arg NVIC_LP_SEVONPEND: Low Power SEV on Pend.
+  *     @arg NVIC_LP_SLEEPDEEP: Low Power DEEPSLEEP request.
+  *     @arg NVIC_LP_SLEEPONEXIT: Low Power Sleep on Exit.
+  * @param  NewState: new state of LP condition. This parameter can be: ENABLE or DISABLE.
+  * @retval None
+  */
+void NVIC_SystemLPConfig(uint8_t LowPowerMode, FunctionalState NewState)
+{
+  /* Check the parameters */
+  assert_param(IS_NVIC_LP(LowPowerMode));
+  assert_param(IS_FUNCTIONAL_STATE(NewState));  
+  
+  if (NewState != DISABLE)
+  {
+    SCB->SCR |= LowPowerMode;
+  }
+  else
+  {
+    SCB->SCR &= (uint32_t)(~(uint32_t)LowPowerMode);
+  }
+}
+
+/**
+  * @brief  Configures the SysTick clock source.
+  * @param  SysTick_CLKSource: specifies the SysTick clock source.
+  *   This parameter can be one of the following values:
+  *     @arg SysTick_CLKSource_HCLK_Div8: AHB clock divided by 8 selected as SysTick clock source.
+  *     @arg SysTick_CLKSource_HCLK: AHB clock selected as SysTick clock source.
+  * @retval None
+  */
+void SysTick_CLKSourceConfig(uint32_t SysTick_CLKSource)
+{
+  /* Check the parameters */
+  assert_param(IS_SYSTICK_CLK_SOURCE(SysTick_CLKSource));
+  if (SysTick_CLKSource == SysTick_CLKSource_HCLK)
+  {
+    SysTick->CTRL |= SysTick_CLKSource_HCLK;
+  }
+  else
+  {
+    SysTick->CTRL &= SysTick_CLKSource_HCLK_Div8;
+  }
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
+