![](/media/cache/img/default_profile.jpg.50x50_q85.jpg)
work in progress
Dependencies: FastAnalogIn FastIO USBDevice mbed FastPWM SimpleDMA
Fork of Pinscape_Controller by
74HC595/74HC595.h
- Committer:
- mjr
- Date:
- 2015-12-03
- Revision:
- 36:6b981a2afab7
File content as of revision 36:6b981a2afab7:
/* Copyright 2014 M J Roberts, MIT License * * Permission is hereby granted, free of charge, to any person obtaining a copy of this software * and associated documentation files (the "Software"), to deal in the Software without * restriction, including without limitation the rights to use, copy, modify, merge, publish, * distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the * Software is furnished to do so, subject to the following conditions: * * The above copyright notice and this permission notice shall be included in all copies or * substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING * BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. */ #ifndef HC595_INCLUDED #define HC595_INCLUDED #include "mbed.h" // 74HC595 Interface // // We require four GPIO pins: // // sin - serial data // sclk - serial clock // latch - the LATCH signal, which transfers the internal shift register // bits to the physical output pin states // ena - the Enable signal // // Note that the physical !OE (output enable) pin on the 74HC595 is active-low. // To allow for orderly startup that guarantees that outputs won't be pulsed // (even briefly) during power-on, we require the !OE pin to be wired with a // pull-up resistor to Vcc, and connected to our ENA GPIO pin via an inverter. // // Recommended wiring: connect the GPIO pin to the base of an NPN transistor // through a 2.2K resistor, connect the collector the !OE pin on the 74HC595, // and connect the emitter to ground. This will pull !OE to ground when we // write a digital 1 to the ENA GPIO, enabling the outputs. // // We use simple bit-banging through plain DigitalOut pins to send serial // data to the chips. This is fast enough for our purposes, since we send // only 8 bits per chip on each update (about 4us per chip per update), and // we only update when we get a command from the PC host that changes an // output state. These updates are at USB speed, so the update interval is // extremely long compared to the bit-banging time. If we wanted to use // these chips to implement PWM controlled by the microcontroller, or we // simply wanted to use a very long daisy-chain, we'd probably have to use // a faster transfer mechanism, such as the SPIO controller. class HC595 { public: HC595(int nchips, PinName sin, PinName sclk, PinName latch, PinName ena) : nchips(nchips), sin(sin), sclk(sclk), latch(latch), ena(ena) { // turn off all pins initially this->sin = 0; this->sclk = 0; this->latch = 0; this->ena = 0; // allocate the state array state = new char[nchips*8]; memset(state, 0, nchips*8); dirty = false; } // Initialize. This must be called once at startup to clear the chips' // shift registers and enable the physical outputs. We clock a 0 bit (OFF // state) to each shift register position, latch the OFF states on the // outputs, and enable the chips. void init() { // set the internal state of all inputs memset(state, 0, nchips*8); dirty = false; // clock a 0 to each shift register bit (8 per chip) sin = 0; for (int i = 0 ; i < nchips*8 ; ++i) { sclk = 1; sclk = 0; } // latch the output data (this transfers the serial data register // bit for each pin to the actual output pin) latch = 1; latch = 0; // enable the outputs ena = 1; } // Set an output state. This only sets the state internally; call // update() to apply changes to the physical outputs. void set(int idx, int val) { if (state[idx] != val) { state[idx] = val; dirty = true; } } // Apply updates. This sends the current state of each pin to the // chips and latches the new settings. void update() { // if we have changes to apply, send the changes if (dirty) { // Clock out the new states. Since the outputs are arranged // as shift registers, we have to clock out the bits in reverse // order of port numbers - the first bit we output will end up // in the last register after we clock out all of the other bits. // So clock out the last bit first and the first bit last. for (int i = nchips*8-1 ; i >= 0 ; --i) { sclk = 0; sin = state[i]; sclk = 1; } // latch the new states latch = 1; sclk = 0; latch = 0; // outputs now reflect internal state dirty = false; } } private: int nchips; // number of chips in daisy chain bool dirty; // do we have changes to send to the chips? DigitalOut sin; // serial data pin DigitalOut sclk; // serial clock pin DigitalOut latch; // latch pin DigitalOut ena; // enable pin char *state; // array of current output states (0=off, 1=on) }; #endif // HC595_INCLUDED