Markus Kalkbrenner
work in progress
Dependencies: FastAnalogIn FastIO USBDevice mbed FastPWM SimpleDMA
Fork of
Pinscape_Controller
by 
Mike R
Diff: config.h
- Revision:
- 36:6b981a2afab7
- Parent:
- 35:d832bcab089e
- Child:
- 38:697e10d8fb80
--- a/config.h Wed Oct 21 21:53:07 2015 +0000
+++ b/config.h Thu Dec 03 07:34:57 2015 +0000
@@ -425,9 +425,10 @@
// Number of TLC5940 chips you're using. For a full LedWiz-compatible
// setup, you need two of these chips, for 32 outputs. The software
-// will handle up to 8. The expansion board uses 4 of these chips; if
-// you're not using the expansion board, we assume you're not using
-// any of them.
+// will handle up to 8.
+// If you're using the expansion board, the main KL25Z interface board
+// has 2 chips and the MOSFET board has 2 more, for a total of 4. If
+// you add extra daisy-chained MOSFET boards, add 2 more per board.
#ifdef EXPANSION_BOARD
# define TLC5940_NCHIPS 4
#else
@@ -440,25 +441,41 @@
// outputs, respectively, which effectively limits them to the default
// selections, and that the GSCLK pin must be PWM-capable. These defaults
// all match the expansion board wiring.
-#define TLC5940_SIN PTC6 // Must connect to SPI0 MOSI -> PTC6 or PTD2
-#define TLC5940_SCLK PTC5 // Must connect to SPI0 SCLK -> PTC5 or PTD1; however, PTD1 isn't
- // recommended because it's hard-wired to the on-board blue LED
-#define TLC5940_XLAT PTC10 // Any GPIO pin can be used
-#define TLC5940_BLANK PTC7 // Any GPIO pin can be used
-#define TLC5940_GSCLK PTA1 // Must be a PWM-capable pin
+#define TLC5940_SIN PTC6 // Serial data - Must connect to SPI0 MOSI -> PTC6 or PTD2
+#define TLC5940_SCLK PTC5 // Serial clock - Must connect to SPI0 SCLK -> PTC5 or PTD1,
+ // but don't use PTD1 because it's hard-wired to the on-board
+ // blue LED
+#define TLC5940_XLAT PTC10 // XLAT (latch) signal - Any GPIO pin can be used
+#define TLC5940_BLANK PTC7 // BLANK signal - Any GPIO pin can be used
+#define TLC5940_GSCLK PTA1 // Grayscale clock - Must be a PWM-capable pin
+
-// TLC5940 output power enable pin. This is a GPIO pin that controls
-// a high-side transistor switch that controls power to the optos and
-// LEDs connected to the TLC5940 outputs. This is a precaution against
-// powering the chip's output pins before Vcc is powered. Vcc comes
-// from the KL25Z, so when our program is running, we know for certain
-// that Vcc is up. This means that we can simply enable this pin any
-// time after entering our main(). Un-comment this line if using this
-// circuit.
-// #define TLC5940_PWRENA PTC11 // Any GPIO pin can be used
-#ifdef EXPANSION_BOARD
-# define TLC5940_PWRENA PTC11
-#endif
+// --------------------------------------------------------------------------
+//
+// 74HC595 digital output setup - "Chime Board" module
+//
+// The 74HC595 is an 8-output serial-to-parallel shift register IC. This lets
+// us add extra digital outputs (on/off only, not PWM), 8 at a time, similar
+// to the way the TLC5940 lets us add extra PWM outputs. The 74HC595 requires
+// four control signals, so one chip gives us 8 outputs using only 4 GPIOs.
+// The chips can be daisy-chained, so by adding multiple chips, we can add
+// any number of new outputs, still using only 4 GPIO pins for the whole chain.
+//
+// The TLC5940 is more useful for general-purpose outputs because of its PWM
+// capabilities, but digital-only outputs are better for some special cases.
+//
+// The Expansion Board "Chime" module uses these chips to add timer-protected
+// outputs. The timer triggers are edge-sensitive, so we want simple on/off
+// signals to control them; a PWM signal wouldn't work properly because it's
+// constantly switching on and off even when nominally 100% on.
+//
+
+#define HC595_NCHIPS 0 // Number of chips == number of Chime boards connected
+#define HC595_SIN PTA5 // Serial data - use any GPIO pin
+#define HC595_SCLK PTA4 // Serial clock - use any GPIO pin
+#define HC595_LATCH PTA12 // Latch signal - use any GPIO pin
+#define HC595_ENA PTD4 // Enable signal - use any GPIO pin
+
#endif // CONFIG_H - end of include-once section (code below this point can be multiply included)
@@ -488,14 +505,15 @@
// "NC" entries below to the reallocated pin name. The limit is 32
// buttons total.
//
-// (If you're using TLC5940 chips to control outputs, ALL of the
-// LedWiz mapped ports can be reassigned as keys, except, of course,
-// those taken over for the 5940 interface.)
+// (If you're using TLC5940 chips to control outputs, many of the
+// GPIO pins that are mapped to LedWiz outputs in the default
+// mapping can be reassigned as keys, since the TLC5940 outputs
+// take over for the GPIO pins. The exceptions are the pins that
+// are reassigned to control the TLC5940 chips.)
//
// Note: PTD1 (pin J2-12) should NOT be assigned as a button input,
// as this pin is physically connected on the KL25Z to the on-board
-// indicator LED's blue segment. This precludes any other use of
-// the pin.
+// indicator LED's blue segment.
PinName buttonMap[] = {
PTC2, // J10 pin 10, joystick button 1
PTB3, // J10 pin 8, joystick button 2
@@ -503,7 +521,11 @@
PTB1, // J10 pin 4, joystick button 4
PTE30, // J10 pin 11, joystick button 5
+#ifdef EXPANSION_BOARD
+ PTC11, // J1 pin 15, joystick button 6
+#else
PTE22, // J10 pin 5, joystick button 6
+#endif
PTE5, // J9 pin 15, joystick button 7
PTE4, // J9 pin 13, joystick button 8
@@ -635,7 +657,7 @@
//
// Note: Don't assign PTD1 (pin J2-12) as an LedWiz output. That pin
// is hard-wired on the KL25Z to the on-board indicator LED's blue segment,
-// which pretty much precludes any other use of the pin.
+// which pretty precludes other uses of the pin.
//
// ACTIVE-LOW PORTS: By default, when a logical port is turned on in
// the software, we set the physical GPIO voltage to "high" (3.3V), and
@@ -648,21 +670,33 @@
// affected port.
//
// TLC5940 PORTS: To assign an LedWiz output port number to a particular
-// output on a TLC5940, set tlcPortNum to the non-zero port number,
-// starting at 1 for the first output on the first chip, 16 for the
-// last output on the first chip, 17 for the first output on the second
-// chip, and so on. TLC ports are inherently PWM-capable only, so it's
-// not necessary to set the PORT_IS_PWM flag for those.
+// output on a TLC5940, set the port type to TLC_PORT and set the 'pin'
+// value to the index of the output port in the daisy chain. The first
+// chip in the daisy chain has ports 1-16, the second has ports 17-32,
+// and so on.
+//
+// 74HC595 PORTS: To assign an LedWiz output port to a 74HC595 port,
+// set the port type to HC595_PORT and set 'pin' to the index of the port
+// in the daisy chain. The first chip has ports 1-8, the second has
+// 9-16, etc.
//
-// ledWizPortMap 'flags' bits - combine these with '|'
-const int PORT_IS_PWM = 0x0001; // this port is PWM-capable
-const int PORT_ACTIVE_LOW = 0x0002; // use LOW voltage (0V) when port is ON
+// ledWizPortMap 'typ' values
+enum LWPortType {
+ NO_PORT = -1, // Not connected
+ DIG_GPIO = 0, // DigitalOut I/O pin (not PWM capable)
+ PWM_GPIO = 1, // AnalogOut I/O pin (PWM capable)
+ TLC_PORT = 2, // TLC5940 output port
+ HC595_PORT = 3 // 74HC595 output port
+};
+
+// flags - combine with '|'
+const int PORT_ACTIVE_LOW = 0x0001; // use LOW voltage (0V) when port is ON
struct {
- PinName pin; // the GPIO pin assigned to this output; NC if not connected or a TLC5940 port
+ int pin; // Pin name/index - PinName for GPIO, pin index for TLC5940 or 74HC595
+ LWPortType typ; // type of pin
int flags; // flags - a combination of PORT_xxx flag bits (see above)
- int tlcPortNum; // for TLC5940 ports, the TLC output number (1 to number of chips*16); otherwise 0
} ledWizPortMap[] = {
#if TLC5940_NCHIPS == 0
@@ -683,39 +717,39 @@
// We commented each PWM pin with its hardware channel number to help you keep
// track of available channels if you do need to rearrange any of these pins.
- { PTA1, PORT_IS_PWM }, // pin J1-2, LW port 1 (PWM capable - TPM 2.0 = channel 9)
- { PTA2, PORT_IS_PWM }, // pin J1-4, LW port 2 (PWM capable - TPM 2.1 = channel 10)
- { PTD4, PORT_IS_PWM }, // pin J1-6, LW port 3 (PWM capable - TPM 0.4 = channel 5)
- { PTA12, PORT_IS_PWM }, // pin J1-8, LW port 4 (PWM capable - TPM 1.0 = channel 7)
- { PTA4, PORT_IS_PWM }, // pin J1-10, LW port 5 (PWM capable - TPM 0.1 = channel 2)
- { PTA5, PORT_IS_PWM }, // pin J1-12, LW port 6 (PWM capable - TPM 0.2 = channel 3)
- { PTA13, PORT_IS_PWM }, // pin J2-2, LW port 7 (PWM capable - TPM 1.1 = channel 13)
- { PTD5, PORT_IS_PWM }, // pin J2-4, LW port 8 (PWM capable - TPM 0.5 = channel 6)
- { PTD0, PORT_IS_PWM }, // pin J2-6, LW port 9 (PWM capable - TPM 0.0 = channel 1)
- { PTD3, PORT_IS_PWM }, // pin J2-10, LW port 10 (PWM capable - TPM 0.3 = channel 4)
- { PTD2, 0 }, // pin J2-8, LW port 11
- { PTC8, 0 }, // pin J1-14, LW port 12
- { PTC9, 0 }, // pin J1-16, LW port 13
- { PTC7, 0 }, // pin J1-1, LW port 14
- { PTC0, 0 }, // pin J1-3, LW port 15
- { PTC3, 0 }, // pin J1-5, LW port 16
- { PTC4, 0 }, // pin J1-7, LW port 17
- { PTC5, 0 }, // pin J1-9, LW port 18
- { PTC6, 0 }, // pin J1-11, LW port 19
- { PTC10, 0 }, // pin J1-13, LW port 20
- { PTC11, 0 }, // pin J1-15, LW port 21
- { PTE0, 0 }, // pin J2-18, LW port 22
- { NC, 0 }, // Not connected, LW port 23
- { NC, 0 }, // Not connected, LW port 24
- { NC, 0 }, // Not connected, LW port 25
- { NC, 0 }, // Not connected, LW port 26
- { NC, 0 }, // Not connected, LW port 27
- { NC, 0 }, // Not connected, LW port 28
- { NC, 0 }, // Not connected, LW port 29
- { NC, 0 }, // Not connected, LW port 30
- { NC, 0 }, // Not connected, LW port 31
- { NC, 0 } // Not connected, LW port 32
-
+ { PTA1, PWM_GPIO }, // pin J1-2, LW port 1 (PWM capable - TPM 2.0 = channel 9)
+ { PTA2, PWM_GPIO }, // pin J1-4, LW port 2 (PWM capable - TPM 2.1 = channel 10)
+ { PTD4, PWM_GPIO }, // pin J1-6, LW port 3 (PWM capable - TPM 0.4 = channel 5)
+ { PTA12, PWM_GPIO }, // pin J1-8, LW port 4 (PWM capable - TPM 1.0 = channel 7)
+ { PTA4, PWM_GPIO }, // pin J1-10, LW port 5 (PWM capable - TPM 0.1 = channel 2)
+ { PTA5, PWM_GPIO }, // pin J1-12, LW port 6 (PWM capable - TPM 0.2 = channel 3)
+ { PTA13, PWM_GPIO }, // pin J2-2, LW port 7 (PWM capable - TPM 1.1 = channel 13)
+ { PTD5, PWM_GPIO }, // pin J2-4, LW port 8 (PWM capable - TPM 0.5 = channel 6)
+ { PTD0, PWM_GPIO }, // pin J2-6, LW port 9 (PWM capable - TPM 0.0 = channel 1)
+ { PTD3, PWM_GPIO }, // pin J2-10, LW port 10 (PWM capable - TPM 0.3 = channel 4)
+ { PTD2, DIG_GPIO }, // pin J2-8, LW port 11
+ { PTC8, DIG_GPIO }, // pin J1-14, LW port 12
+ { PTC9, DIG_GPIO }, // pin J1-16, LW port 13
+ { PTC7, DIG_GPIO }, // pin J1-1, LW port 14
+ { PTC0, DIG_GPIO }, // pin J1-3, LW port 15
+ { PTC3, DIG_GPIO }, // pin J1-5, LW port 16
+ { PTC4, DIG_GPIO }, // pin J1-7, LW port 17
+ { PTC5, DIG_GPIO }, // pin J1-9, LW port 18
+ { PTC6, DIG_GPIO }, // pin J1-11, LW port 19
+ { PTC10, DIG_GPIO }, // pin J1-13, LW port 20
+ { PTC11, DIG_GPIO }, // pin J1-15, LW port 21
+ { PTE0, DIG_GPIO }, // pin J2-18, LW port 22
+ { NC, NO_PORT }, // Not connected, LW port 23
+ { NC, NO_PORT }, // Not connected, LW port 24
+ { NC, NO_PORT }, // Not connected, LW port 25
+ { NC, NO_PORT }, // Not connected, LW port 26
+ { NC, NO_PORT }, // Not connected, LW port 27
+ { NC, NO_PORT }, // Not connected, LW port 28
+ { NC, NO_PORT }, // Not connected, LW port 29
+ { NC, NO_PORT }, // Not connected, LW port 30
+ { NC, NO_PORT }, // Not connected, LW port 31
+ { NC, NO_PORT } // Not connected, LW port 32
+
#elif defined(EXPANSION_BOARD)
// *** EXPANSION BOARD MODE ***
@@ -733,80 +767,100 @@
// damaged, so they don't require such elaborate precautions.)
//
// The specific device assignments in the last column are just
- // recommendations - you can assign any port to any device with
+ // recommendations. You can assign any port to any device with
// compatible power needs. The "General Purpose" ports are good to
- // at least 5A, so you can use these for virtually anything. The
- // "Button light" ports are good to about 1.5A, so these are most
- // suitable for smaller loads like lamps, flashers, LEDs, etc. The
- // flipper and magnasave ports will only provide 20mA, so these are
- // only usable for small LEDs.
+ // at least 5A, so you can use these for virtually anything; put
+ // your heavy-duty devices, such as solenoids and motors, on these
+ // outputs. You can also put lighter loads like lamps and LEDs
+ // on these if you have ports left over after connecting all of
+ // your high-power devices. The "Flasher" and "Button light" ports
+ // are good to about 1.5A, so they work for medium loads like lamps,
+ // flashers, high-power LEDs, etc. The flipper and magnasave ports
+ // only provide 20mA; use these only for small LEDs.
+ //
+ // The TLC5940 outputs on the expansion board are hard-wired to
+ // specific output drivers - that's what determines the power
+ // limits described above. You can rearrange the ports in the
+ // list below to change the LedWiz port numbering to any order
+ // you prefer, but the association between a TLC5940 port number
+ // and the output circuit type can't be changed in the software.
+ // That's a function of how the TLC5940 port is physically wired
+ // on the board. Likewise, the PTC8 output is hard-wired to the
+ // knocker time limiter.
+ // TLC ports 1-20 and 44-47 = Darlington outputs, 1.5A max
+ // TLC ports 21-44 = MOSFET outputs (limit depends on MOSFET chosen)
+ // TLC ports 49-64 = direct outputs, limited to 20mA
// The first 32 ports are LedWiz-compatible, so they're universally
// accessible, even to older non-DOF software. Attach the most common
// devices to these ports.
- { NC, 0, 1 }, // TLC port 1, LW output 1 - Flasher 1 R
- { NC, 0, 2 }, // TLC port 2, LW output 2 - Flasher 1 G
- { NC, 0, 3 }, // TLC port 3, LW output 3 - Flasher 1 B
- { NC, 0, 4 }, // TLC port 4, LW output 4 - Flasher 2 R
- { NC, 0, 5 }, // TLC port 5, LW output 5 - Flasher 2 G
- { NC, 0, 6 }, // TLC port 6, LW output 6 - Flasher 2 B
- { NC, 0, 7 }, // TLC port 7, LW output 7 - Flasher 3 R
- { NC, 0, 8 }, // TLC port 8, LW output 8 - Flasher 3 G
- { NC, 0, 9 }, // TLC port 9, LW output 9 - Flasher 3 B
- { NC, 0, 10 }, // TLC port 10, LW output 10 - Flasher 4 R
- { NC, 0, 11 }, // TLC port 11, LW output 11 - Flasher 4 G
- { NC, 0, 12 }, // TLC port 12, LW output 12 - Flasher 4 B
- { NC, 0, 13 }, // TLC port 13, LW output 13 - Flasher 5 R
- { NC, 0, 14 }, // TLC port 14, LW output 14 - Flasher 5 G
- { NC, 0, 15 }, // TLC port 15, LW output 15 - Flasher 5 B
- { NC, 0, 16 }, // TLC port 16, LW output 16 - Strobe/Button light
- { NC, 0, 17 }, // TLC port 17, LW output 17 - Button light 1
- { NC, 0, 18 }, // TLC port 18, LW output 18 - Button light 2
- { NC, 0, 19 }, // TLC port 19, LW output 19 - Button light 3
- { NC, 0, 20 }, // TLC port 20, LW output 20 - Button light 4
- { PTC8, 0, 0 }, // PTC8, LW output 21 - Replay Knocker
- { NC, 0, 21 }, // TLC port 21, LW output 22 - Contactor 1/General purpose
- { NC, 0, 22 }, // TLC port 22, LW output 23 - Contactor 2/General purpose
- { NC, 0, 23 }, // TLC port 23, LW output 24 - Contactor 3/General purpose
- { NC, 0, 24 }, // TLC port 24, LW output 25 - Contactor 4/General purpose
- { NC, 0, 25 }, // TLC port 25, LW output 26 - Contactor 5/General purpose
- { NC, 0, 26 }, // TLC port 26, LW output 27 - Contactor 6/General purpose
- { NC, 0, 27 }, // TLC port 27, LW output 28 - Contactor 7/General purpose
- { NC, 0, 28 }, // TLC port 28, LW output 29 - Contactor 8/General purpose
- { NC, 0, 29 }, // TLC port 29, LW output 30 - Contactor 9/General purpose
- { NC, 0, 30 }, // TLC port 30, LW output 31 - Contactor 10/General purpose
- { NC, 0, 31 }, // TLC port 31, LW output 32 - Shaker Motor/General purpose
+ { 1, TLC_PORT }, // TLC port 1, LW output 1 - Flasher 1 R
+ { 2, TLC_PORT }, // TLC port 2, LW output 2 - Flasher 1 G
+ { 3, TLC_PORT }, // TLC port 3, LW output 3 - Flasher 1 B
+ { 4, TLC_PORT }, // TLC port 4, LW output 4 - Flasher 2 R
+ { 5, TLC_PORT }, // TLC port 5, LW output 5 - Flasher 2 G
+ { 6, TLC_PORT }, // TLC port 6, LW output 6 - Flasher 2 B
+ { 7, TLC_PORT }, // TLC port 7, LW output 7 - Flasher 3 R
+ { 8, TLC_PORT }, // TLC port 8, LW output 8 - Flasher 3 G
+ { 9, TLC_PORT }, // TLC port 9, LW output 9 - Flasher 3 B
+ { 10, TLC_PORT }, // TLC port 10, LW output 10 - Flasher 4 R
+ { 11, TLC_PORT }, // TLC port 11, LW output 11 - Flasher 4 G
+ { 12, TLC_PORT }, // TLC port 12, LW output 12 - Flasher 4 B
+ { 13, TLC_PORT }, // TLC port 13, LW output 13 - Flasher 5 R
+ { 14, TLC_PORT }, // TLC port 14, LW output 14 - Flasher 5 G
+ { 15, TLC_PORT }, // TLC port 15, LW output 15 - Flasher 5 B
+ { 16, TLC_PORT }, // TLC port 16, LW output 16 - Strobe/Button light
+ { 17, TLC_PORT }, // TLC port 17, LW output 17 - Button light 1
+ { 18, TLC_PORT }, // TLC port 18, LW output 18 - Button light 2
+ { 19, TLC_PORT }, // TLC port 19, LW output 19 - Button light 3
+ { 20, TLC_PORT }, // TLC port 20, LW output 20 - Button light 4
+ { PTC8, DIG_GPIO }, // PTC8, LW output 21 - Replay Knocker
+ { 21, TLC_PORT }, // TLC port 21, LW output 22 - Contactor 1/General purpose
+ { 22, TLC_PORT }, // TLC port 22, LW output 23 - Contactor 2/General purpose
+ { 23, TLC_PORT }, // TLC port 23, LW output 24 - Contactor 3/General purpose
+ { 24, TLC_PORT }, // TLC port 24, LW output 25 - Contactor 4/General purpose
+ { 25, TLC_PORT }, // TLC port 25, LW output 26 - Contactor 5/General purpose
+ { 26, TLC_PORT }, // TLC port 26, LW output 27 - Contactor 6/General purpose
+ { 27, TLC_PORT }, // TLC port 27, LW output 28 - Contactor 7/General purpose
+ { 28, TLC_PORT }, // TLC port 28, LW output 29 - Contactor 8/General purpose
+ { 29, TLC_PORT }, // TLC port 29, LW output 30 - Contactor 9/General purpose
+ { 30, TLC_PORT }, // TLC port 30, LW output 31 - Contactor 10/General purpose
+ { 31, TLC_PORT }, // TLC port 31, LW output 32 - Shaker Motor/General purpose
// Ports 33+ are accessible only to DOF-based software. Older LedWiz-only
// software on the can't access these. Attach less common devices to these ports.
- { NC, 0, 32 }, // TLC port 32, LW output 33 - Gear Motor/General purpose
- { NC, 0, 33 }, // TLC port 33, LW output 34 - Fan/General purpose
- { NC, 0, 34 }, // TLC port 34, LW output 35 - Beacon/General purpose
- { NC, 0, 35 }, // TLC port 35, LW output 36 - Undercab RGB R/General purpose
- { NC, 0, 36 }, // TLC port 36, LW output 37 - Undercab RGB G/General purpose
- { NC, 0, 37 }, // TLC port 37, LW output 38 - Undercab RGB B/General purpose
- { NC, 0, 38 }, // TLC port 38, LW output 39 - Bell/General purpose
- { NC, 0, 39 }, // TLC port 39, LW output 40 - Chime 1/General purpose
- { NC, 0, 40 }, // TLC port 40, LW output 41 - Chime 2/General purpose
- { NC, 0, 41 }, // TLC port 41, LW output 42 - Chime 3/General purpose
- { NC, 0, 42 }, // TLC port 42, LW output 43 - General purpose
- { NC, 0, 43 }, // TLC port 43, LW output 44 - General purpose
- { NC, 0, 44 }, // TLC port 44, LW output 45 - Button light 5
- { NC, 0, 45 }, // TLC port 45, LW output 46 - Button light 6
- { NC, 0, 46 }, // TLC port 46, LW output 47 - Button light 7
- { NC, 0, 47 }, // TLC port 47, LW output 48 - Button light 8
- { NC, 0, 49 }, // TLC port 49, LW output 49 - Flipper button RGB left R
- { NC, 0, 50 }, // TLC port 50, LW output 50 - Flipper button RGB left G
- { NC, 0, 51 }, // TLC port 51, LW output 51 - Flipper button RGB left B
- { NC, 0, 52 }, // TLC port 52, LW output 52 - Flipper button RGB right R
- { NC, 0, 53 }, // TLC port 53, LW output 53 - Flipper button RGB right G
- { NC, 0, 54 }, // TLC port 54, LW output 54 - Flipper button RGB right B
- { NC, 0, 55 }, // TLC port 55, LW output 55 - MagnaSave button RGB left R
- { NC, 0, 56 }, // TLC port 56, LW output 56 - MagnaSave button RGB left G
- { NC, 0, 57 }, // TLC port 57, LW output 57 - MagnaSave button RGB left B
- { NC, 0, 58 }, // TLC port 58, LW output 58 - MagnaSave button RGB right R
- { NC, 0, 59 }, // TLC port 59, LW output 59 - MagnaSave button RGB right G
- { NC, 0, 60 } // TLC port 60, LW output 60 - MagnaSave button RGB right B
+ { 32, TLC_PORT }, // TLC port 32, LW output 33 - Gear Motor/General purpose
+ { 33, TLC_PORT }, // TLC port 33, LW output 34 - Fan/General purpose
+ { 34, TLC_PORT }, // TLC port 34, LW output 35 - Beacon/General purpose
+ { 35, TLC_PORT }, // TLC port 35, LW output 36 - Undercab RGB R/General purpose
+ { 36, TLC_PORT }, // TLC port 36, LW output 37 - Undercab RGB G/General purpose
+ { 37, TLC_PORT }, // TLC port 37, LW output 38 - Undercab RGB B/General purpose
+ { 38, TLC_PORT }, // TLC port 38, LW output 39 - Bell/General purpose
+ { 39, TLC_PORT }, // TLC port 39, LW output 40 - Chime 1/General purpose
+ { 40, TLC_PORT }, // TLC port 40, LW output 41 - Chime 2/General purpose
+ { 41, TLC_PORT }, // TLC port 41, LW output 42 - Chime 3/General purpose
+ { 42, TLC_PORT }, // TLC port 42, LW output 43 - General purpose
+ { 43, TLC_PORT }, // TLC port 43, LW output 44 - General purpose
+ { 44, TLC_PORT }, // TLC port 44, LW output 45 - Button light 5
+ { 45, TLC_PORT }, // TLC port 45, LW output 46 - Button light 6
+ { 46, TLC_PORT }, // TLC port 46, LW output 47 - Button light 7
+ { 47, TLC_PORT }, // TLC port 47, LW output 48 - Button light 8
+ { 49, TLC_PORT }, // TLC port 49, LW output 49 - Flipper button RGB left R
+ { 50, TLC_PORT }, // TLC port 50, LW output 50 - Flipper button RGB left G
+ { 51, TLC_PORT }, // TLC port 51, LW output 51 - Flipper button RGB left B
+ { 52, TLC_PORT }, // TLC port 52, LW output 52 - Flipper button RGB right R
+ { 53, TLC_PORT }, // TLC port 53, LW output 53 - Flipper button RGB right G
+ { 54, TLC_PORT }, // TLC port 54, LW output 54 - Flipper button RGB right B
+ { 55, TLC_PORT }, // TLC port 55, LW output 55 - MagnaSave button RGB left R
+ { 56, TLC_PORT }, // TLC port 56, LW output 56 - MagnaSave button RGB left G
+ { 57, TLC_PORT }, // TLC port 57, LW output 57 - MagnaSave button RGB left B
+ { 58, TLC_PORT }, // TLC port 58, LW output 58 - MagnaSave button RGB right R
+ { 59, TLC_PORT }, // TLC port 59, LW output 59 - MagnaSave button RGB right G
+ { 60, TLC_PORT }, // TLC port 60, LW output 60 - MagnaSave button RGB right B
+ { 61, TLC_PORT }, // TLC port 61, LW output 61 - Extra RGB LED R
+ { 62, TLC_PORT }, // TLC port 62, LW output 62 - Extra RGB LED G
+ { 63, TLC_PORT }, // TLC port 63, LW output 63 - Extra RGB LED B
+ { 64, TLC_PORT } // TLC port 64, LW output 64 - Extra single LED
#else
@@ -838,16 +892,17 @@
// in this set. This leaves the following ports from the basic mode output
// set available for other users: PTA13, PTD0, PTD2, PTD3, PTD5, PTE0.
- { PTC8, 0 }, // pin J1-14, LW port 1
- { PTC9, 0 }, // pin J1-16, LW port 2
- { PTC0, 0 }, // pin J1-3, LW port 3
- { PTC3, 0 }, // pin J1-5, LW port 4
- { PTC4, 0 }, // pin J1-7, LW port 5
- { PTA2, PORT_IS_PWM }, // pin J1-4, LW port 6 (PWM capable - TPM 2.1 = channel 10)
- { PTD4, PORT_IS_PWM }, // pin J1-6, LW port 7 (PWM capable - TPM 0.4 = channel 5)
- { PTA12, PORT_IS_PWM }, // pin J1-8, LW port 8 (PWM capable - TPM 1.0 = channel 7)
- { PTA4, PORT_IS_PWM }, // pin J1-10, LW port 9 (PWM capable - TPM 0.1 = channel 2)
- { PTA5, PORT_IS_PWM } // pin J1-12, LW port 10 (PWM capable - TPM 0.2 = channel 3)
+ { PTC8, DIG_GPIO }, // pin J1-14, LW port 1
+ { PTC9, DIG_GPIO }, // pin J1-16, LW port 2
+ { PTC0, DIG_GPIO }, // pin J1-3, LW port 3
+ { PTC3, DIG_GPIO }, // pin J1-5, LW port 4
+ { PTC4, DIG_GPIO }, // pin J1-7, LW port 5
+ { PTC11, DIG_GPIO }, // pin J1-15, LW port 6
+ { PTA2, PWM_GPIO }, // pin J1-4, LW port 7 (PWM capable - TPM 2.1 = channel 10)
+ { PTD4, PWM_GPIO }, // pin J1-6, LW port 8 (PWM capable - TPM 0.4 = channel 5)
+ { PTA12, PWM_GPIO }, // pin J1-8, LW port 9 (PWM capable - TPM 1.0 = channel 7)
+ { PTA4, PWM_GPIO }, // pin J1-10, LW port 10 (PWM capable - TPM 0.1 = channel 2)
+ { PTA5, PWM_GPIO } // pin J1-12, LW port 11 (PWM capable - TPM 0.2 = channel 3)
// TLC5940 ports start here!
// First chip port 0 -> LW port 12