Diff: MAG3110.h

Revision:

1:5a0e7a58d980

Parent:

0:63a8594a3866

Child:

2:fb8024297377

diff -r 63a8594a3866 -r 5a0e7a58d980 MAG3110.h
--- a/MAG3110.h	Sun May 19 20:34:27 2013 +0000
+++ b/MAG3110.h	Fri May 24 20:04:48 2013 +0000
@@ -1,5 +1,5 @@
-/* 
- * MAG3110 Sensor Library for mbed 
+/*
+ * MAG3110 Sensor Library for mbed
  * TODO: Add proper header
  */
 
@@ -75,22 +75,66 @@
 
 class MAG3110
 {
-    private:
-        short _i2c_address;
-        I2C *_i2c;
-        Serial *_pc;
-        bool _debug;
-        int _avgX, _avgY;   //, _newX, _tempXmin, _tempXmax, _newY, _tempYmin, _tempYmax;
+private:
+    int _i2c_address;
+    I2C _i2c;
+    Serial *_pc;
+    bool _debug;
+    int _avgX, _avgY;
 
 
-    public:
-        MAG3110(I2C *i2c);
-        MAG3110(I2C *i2c, Serial *pc); //pass serial for debug
-        void begin();
-        int readReg(char regAddr);
-        int readVal(char regAddr);
-        float getHeading();
-        void getValues(int *xVal, int *yVal, int *zVal);
-        void setCalibration(int minX, int maxX, int minY, int maxY);
+public:
+    /**
+     * MAG3110 constructor
+     * @param sda SDA pin
+     * @param sdl SCL pin
+     * @param addr addr of the I2C peripheral
+     */
+    MAG3110(PinName sda, PinName scl);
+    /**
+     * MAG3110 constructor
+     * @param sda SDA pin
+     * @param sdl SCL pin
+     * @param addr addr of the I2C peripheral
+     * @param pc serial port object to output debug messages
+     */
+    MAG3110(PinName sda, PinName scl, Serial *pc); //pass serial for debug
+    /**
+     * Setup the Magnetometer
+     *
+     */
+    void begin();
+    /**
+     * Read a register, return its value as int
+     * @param regAddr The address to read
+     * @return value in register
+     */
+    int readReg(char regAddr);
+    /**
+     * Read a value from a pair of registers, return as int
+     * @param regAddr The address to read
+     * @return Value from 2 consecutive registers
+     */
+    int readVal(char regAddr);
+    /**
+     * Calculate the heading
+     * @return heading in degrees
+     */
+    float getHeading();
+    /**
+     * Perform a read on the X, Y and Z values.
+     * @param xVal Pointer to X value
+     * @param yVal Pointer to Y value
+     * @param zVal Pointer to Z value
+     */
+    void getValues(int *xVal, int *yVal, int *zVal);
+    /**
+     * Set the calibration parameters if required.
+     * @param minX Minimum value for X range
+     * @param maxX Maximum value for X range
+     * @param minY Minimum value for Y range
+     * @param maxY maximum value for Y range
+     */
+    void setCalibration(int minX, int maxX, int minY, int maxY);
 };
-#endif
\ No newline at end of file
+#endif