Fork of mbed-src file paths change. LPC1114FN28 use only.
Fork of mbed-src by
Information
この情報は2013/10/28時点での解決方法です。
現在はmbed-src、標準ライブラリで問題なくコンパイルが可能です。
・使う物
LPC1114FN28
mbed SDK
LPC1114FN28でmbed-SDKのLibraryを使うとCompile出来ない。(2013/10/28)
パスが通ってないだけのようなのでファイルを以下に移動する。
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\にある
TOOLCHAIN_ARM_MICRO |
をフォルダごと
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\hal\TARGET_NXP\ |
へ移動
移動後は以下のような構成になると思います。
※不要なファイルは削除してあります。
ファイルの移動が面倒なので以下に本家からフォークしたライブラリを置いておきます。
Import librarymbed-src-LPC1114FN28
Fork of mbed-src file paths change. LPC1114FN28 use only.
エラーが出力される場合
"TOOLCHAIN_ARM_MICRO"が無いとエラーになる。
Error: Undefined symbol _initial_sp (referred from entry2.o). Error: Undefined symbol _heap_base (referred from malloc.o). Error: Undefined symbol _heap_limit (referred from malloc.o). |
LPC1114FN28はMicrolibを使ってCompileされるため上記のエラーになるようです。
common/SerialBase.cpp
- Committer:
- mbed_official
- Date:
- 2013-10-23
- Revision:
- 36:ab3ee77451e7
File content as of revision 36:ab3ee77451e7:
/* mbed Microcontroller Library * Copyright (c) 2006-2013 ARM Limited * * Licensed under the Apache License, Version 2.0 (the "License"); * you may not use this file except in compliance with the License. * You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. */ #include "SerialBase.h" #include "wait_api.h" #if DEVICE_SERIAL namespace mbed { SerialBase::SerialBase(PinName tx, PinName rx) { serial_init(&_serial, tx, rx); _baud = 9600; serial_irq_handler(&_serial, SerialBase::_irq_handler, (uint32_t)this); } void SerialBase::baud(int baudrate) { serial_baud(&_serial, baudrate); _baud = baudrate; } void SerialBase::format(int bits, Parity parity, int stop_bits) { serial_format(&_serial, bits, (SerialParity)parity, stop_bits); } int SerialBase::readable() { return serial_readable(&_serial); } int SerialBase::writeable() { return serial_writable(&_serial); } void SerialBase::attach(void (*fptr)(void), IrqType type) { if (fptr) { _irq[type].attach(fptr); serial_irq_set(&_serial, (SerialIrq)type, 1); } else { serial_irq_set(&_serial, (SerialIrq)type, 0); } } void SerialBase::_irq_handler(uint32_t id, SerialIrq irq_type) { SerialBase *handler = (SerialBase*)id; handler->_irq[irq_type].call(); } int SerialBase::_base_getc() { return serial_getc(&_serial); } int SerialBase::_base_putc(int c) { serial_putc(&_serial, c); return c; } void SerialBase::send_break() { // Wait for 1.5 frames before clearing the break condition // This will have different effects on our platforms, but should // ensure that we keep the break active for at least one frame. // We consider a full frame (1 start bit + 8 data bits bits + // 1 parity bit + 2 stop bits = 12 bits) for computation. // One bit time (in us) = 1000000/_baud // Twelve bits: 12000000/baud delay // 1.5 frames: 18000000/baud delay serial_break_set(&_serial); wait_us(18000000/_baud); serial_break_clear(&_serial); } } // namespace mbed #endif