Fork of mbed-src file paths change. LPC1114FN28 use only.
Fork of mbed-src by
Information
この情報は2013/10/28時点での解決方法です。
現在はmbed-src、標準ライブラリで問題なくコンパイルが可能です。
・使う物
LPC1114FN28
mbed SDK
LPC1114FN28でmbed-SDKのLibraryを使うとCompile出来ない。(2013/10/28)
パスが通ってないだけのようなのでファイルを以下に移動する。
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\にある
TOOLCHAIN_ARM_MICRO |
をフォルダごと
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\hal\TARGET_NXP\ |
へ移動
移動後は以下のような構成になると思います。
※不要なファイルは削除してあります。
![]() |
ファイルの移動が面倒なので以下に本家からフォークしたライブラリを置いておきます。
Import librarymbed-src-LPC1114FN28
Fork of mbed-src file paths change. LPC1114FN28 use only.
エラーが出力される場合
"TOOLCHAIN_ARM_MICRO"が無いとエラーになる。
Error: Undefined symbol _initial_sp (referred from entry2.o). Error: Undefined symbol _heap_base (referred from malloc.o). Error: Undefined symbol _heap_limit (referred from malloc.o). |
LPC1114FN28はMicrolibを使ってCompileされるため上記のエラーになるようです。
targets/hal/TARGET_STM/TARGET_STM32F4XX/port_api.c
- Committer:
- bogdanm
- Date:
- 2013-09-10
- Revision:
- 20:4263a77256ae
File content as of revision 20:4263a77256ae:
/* mbed Microcontroller Library * Copyright (c) 2006-2013 ARM Limited * * Licensed under the Apache License, Version 2.0 (the "License"); * you may not use this file except in compliance with the License. * You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. */ #include "port_api.h" #include "pinmap.h" #include "gpio_api.h" #if DEVICE_PORTIN || DEVICE_PORTOUT PinName port_pin(PortName port, int pin_n) { return pin_n + (port << 4); } void port_init(port_t *obj, PortName port, int mask, PinDirection dir) { obj->port = port; obj->mask = mask; uint32_t port_index = (uint32_t) port; GPIO_TypeDef *port_reg = (GPIO_TypeDef *)(GPIOA_BASE + (port_index << 10)); // Enable GPIO peripheral clock RCC->AHB1ENR |= 1 << port_index; obj->reg_mode = &port_reg->MODER; obj->reg_set = &port_reg->BSRRH; obj->reg_clr = &port_reg->BSRRL; obj->reg_in = &port_reg->IDR; obj->reg_out = &port_reg->ODR; port_dir(obj, dir); } void port_mode(port_t *obj, PinMode mode) { uint32_t i; // The mode is set per pin: reuse pinmap logic for (i=0; i<16; i++) { if (obj->mask & (1<<i)) { pin_mode(port_pin(obj->port, i), mode); } } } void port_dir(port_t *obj, PinDirection dir) { obj->direction = dir; uint32_t tmp = *obj->reg_mode; for (int i=0; i<16; i++) { if (obj->mask & (1 << i)) { // Clear the mode bits (i.e. set to input) tmp &= ~(0x3 << (i << 1)); if (dir == PIN_OUTPUT) { // Set to output tmp |= 0x1 << (i << 1); } } } *obj->reg_mode = tmp; } void port_write(port_t *obj, int value) { *obj->reg_out = (*obj->reg_out & ~obj->mask) | (value & obj->mask); } int port_read(port_t *obj) { switch (obj->direction) { case PIN_OUTPUT: return *obj->reg_out & obj->mask; case PIN_INPUT: return *obj->reg_in & obj->mask; } return 0; } #endif