Fork of mbed-src file paths change. LPC1114FN28 use only.
Fork of mbed-src by
Information
この情報は2013/10/28時点での解決方法です。
現在はmbed-src、標準ライブラリで問題なくコンパイルが可能です。
・使う物
LPC1114FN28
mbed SDK
LPC1114FN28でmbed-SDKのLibraryを使うとCompile出来ない。(2013/10/28)
パスが通ってないだけのようなのでファイルを以下に移動する。
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\にある
TOOLCHAIN_ARM_MICRO |
をフォルダごと
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\hal\TARGET_NXP\ |
へ移動
移動後は以下のような構成になると思います。
※不要なファイルは削除してあります。
![]() |
ファイルの移動が面倒なので以下に本家からフォークしたライブラリを置いておきます。
Import librarymbed-src-LPC1114FN28
Fork of mbed-src file paths change. LPC1114FN28 use only.
エラーが出力される場合
"TOOLCHAIN_ARM_MICRO"が無いとエラーになる。
Error: Undefined symbol _initial_sp (referred from entry2.o). Error: Undefined symbol _heap_base (referred from malloc.o). Error: Undefined symbol _heap_limit (referred from malloc.o). |
LPC1114FN28はMicrolibを使ってCompileされるため上記のエラーになるようです。
Diff: targets/hal/TARGET_STM/TARGET_STM32F4XX/port_api.c
- Revision:
- 20:4263a77256ae
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/hal/TARGET_STM/TARGET_STM32F4XX/port_api.c Tue Sep 10 15:14:19 2013 +0300 @@ -0,0 +1,83 @@ +/* mbed Microcontroller Library + * Copyright (c) 2006-2013 ARM Limited + * + * Licensed under the Apache License, Version 2.0 (the "License"); + * you may not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ +#include "port_api.h" +#include "pinmap.h" +#include "gpio_api.h" + +#if DEVICE_PORTIN || DEVICE_PORTOUT + +PinName port_pin(PortName port, int pin_n) { + return pin_n + (port << 4); +} + +void port_init(port_t *obj, PortName port, int mask, PinDirection dir) { + obj->port = port; + obj->mask = mask; + + uint32_t port_index = (uint32_t) port; + + GPIO_TypeDef *port_reg = (GPIO_TypeDef *)(GPIOA_BASE + (port_index << 10)); + // Enable GPIO peripheral clock + RCC->AHB1ENR |= 1 << port_index; + + obj->reg_mode = &port_reg->MODER; + obj->reg_set = &port_reg->BSRRH; + obj->reg_clr = &port_reg->BSRRL; + obj->reg_in = &port_reg->IDR; + obj->reg_out = &port_reg->ODR; + + port_dir(obj, dir); +} + +void port_mode(port_t *obj, PinMode mode) { + uint32_t i; + // The mode is set per pin: reuse pinmap logic + for (i=0; i<16; i++) { + if (obj->mask & (1<<i)) { + pin_mode(port_pin(obj->port, i), mode); + } + } +} + +void port_dir(port_t *obj, PinDirection dir) { + obj->direction = dir; + uint32_t tmp = *obj->reg_mode; + for (int i=0; i<16; i++) { + if (obj->mask & (1 << i)) { + // Clear the mode bits (i.e. set to input) + tmp &= ~(0x3 << (i << 1)); + if (dir == PIN_OUTPUT) { + // Set to output + tmp |= 0x1 << (i << 1); + } + } + } + *obj->reg_mode = tmp; +} + +void port_write(port_t *obj, int value) { + *obj->reg_out = (*obj->reg_out & ~obj->mask) | (value & obj->mask); +} + +int port_read(port_t *obj) { + switch (obj->direction) { + case PIN_OUTPUT: return *obj->reg_out & obj->mask; + case PIN_INPUT: return *obj->reg_in & obj->mask; + } + return 0; +} + +#endif