Fork of mbed-src file paths change. LPC1114FN28 use only.
Fork of mbed-src by
Information
この情報は2013/10/28時点での解決方法です。
現在はmbed-src、標準ライブラリで問題なくコンパイルが可能です。
・使う物
LPC1114FN28
mbed SDK
LPC1114FN28でmbed-SDKのLibraryを使うとCompile出来ない。(2013/10/28)
パスが通ってないだけのようなのでファイルを以下に移動する。
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\にある
TOOLCHAIN_ARM_MICRO |
をフォルダごと
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\hal\TARGET_NXP\ |
へ移動
移動後は以下のような構成になると思います。
※不要なファイルは削除してあります。
![]() |
ファイルの移動が面倒なので以下に本家からフォークしたライブラリを置いておきます。
Import librarymbed-src-LPC1114FN28
Fork of mbed-src file paths change. LPC1114FN28 use only.
エラーが出力される場合
"TOOLCHAIN_ARM_MICRO"が無いとエラーになる。
Error: Undefined symbol _initial_sp (referred from entry2.o). Error: Undefined symbol _heap_base (referred from malloc.o). Error: Undefined symbol _heap_limit (referred from malloc.o). |
LPC1114FN28はMicrolibを使ってCompileされるため上記のエラーになるようです。
targets/hal/TARGET_Freescale/TARGET_KL46Z/port_api.c
- Committer:
- mbed_official
- Date:
- 2013-09-25
- Revision:
- 31:42176bc3c368
File content as of revision 31:42176bc3c368:
/* mbed Microcontroller Library * Copyright (c) 2006-2013 ARM Limited * * Licensed under the Apache License, Version 2.0 (the "License"); * you may not use this file except in compliance with the License. * You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. */ #include "port_api.h" #include "pinmap.h" #include "gpio_api.h" PinName port_pin(PortName port, int pin_n) { return (PinName)((port << PORT_SHIFT) | (pin_n << 2)); } void port_init(port_t *obj, PortName port, int mask, PinDirection dir) { obj->port = port; obj->mask = mask; FGPIO_Type *reg = (FGPIO_Type *)(FPTA_BASE + port * 0x40); obj->reg_out = ®->PDOR; obj->reg_in = ®->PDIR; obj->reg_dir = ®->PDDR; uint32_t i; // The function is set per pin: reuse gpio logic for (i=0; i<32; i++) { if (obj->mask & (1<<i)) { gpio_set(port_pin(obj->port, i)); } } port_dir(obj, dir); } void port_mode(port_t *obj, PinMode mode) { uint32_t i; // The mode is set per pin: reuse pinmap logic for (i=0; i<32; i++) { if (obj->mask & (1<<i)) { pin_mode(port_pin(obj->port, i), mode); } } } void port_dir(port_t *obj, PinDirection dir) { switch (dir) { case PIN_INPUT : *obj->reg_dir &= ~obj->mask; break; case PIN_OUTPUT: *obj->reg_dir |= obj->mask; break; } } void port_write(port_t *obj, int value) { *obj->reg_out = (*obj->reg_in & ~obj->mask) | (value & obj->mask); } int port_read(port_t *obj) { return (*obj->reg_in & obj->mask); }