cycyy
Dependencies: MCP23017 WattBob_TextLCD
WattBob_TextLCD.cpp
- Committer:
- mihaidd
- Date:
- 2019-05-08
- Revision:
- 0:a9b4ee4ed395
File content as of revision 0:a9b4ee4ed395:
/* draft mbed TextLCD * (c) 2007/8, sford * Modified jherd */ #include "WattBob_TextLCD.h" #include "MCP23017.h" #include "mbed.h" /* * Initialisation * ============== * * After attaching the supply voltage/after a reset, the display needs to be brought in to a defined state * * - wait approximately 15 ms so the display is ready to execute commands * - Execute the command 0x30 ("Display Settings") three times (wait 1,64ms after each command, the busy flag cannot be queried now). * - The display is in 8 bit mode, so if you have only connected 4 data pins you should only transmit the higher nibble of each command. * - If you want to use the 4 bit mode, now you can execute the command to switch over to this mode now. * - Execute the "clear display" command * * Timing * ====== * * Nearly all commands transmitted to the display need 40us for execution. * Exceptions are the commands "Clear Display and Reset" and "Set Cursor to Start Position" * These commands need 1.64ms for execution. These timings are valid for all displays working with an * internal clock of 250kHz. But I do not know any displays that use other frequencies. Any time you * can use the busy flag to test if the display is ready to accept the next command. * * _e is kept high apart from calling clock * _rw is kept 0 (write) apart from actions that uses it differently * _rs is set by the data/command writes * * RS = 7 * RW = 6 * E = 5 * Back light = 4 * D4 = 0 * D5 = 1 * D6 = 2 * D7 = 3 */ WattBob_TextLCD::WattBob_TextLCD(MCP23017 *port) { // // Initialise pointer to MCP23017 object // par_port = port; par_port->config(0x0F00, 0x0F00, 0x0F00); _rows = 2; _columns = 16; // // Time to allow unit to initialise // wait(DISPLAY_INIT_DELAY_SECS); _rw(0); _e(0); _rs(0); // command mode // // interface defaults to an 8-bit interface. However, we need to ensure that we // are in 8-bit mode // for(int i=0; i<3; i++) { writeNibble(CMD4_SET_8_BIT_INTERFACE); wait(0.00164); // this command takes 1.64ms, so wait for it } writeNibble(CMD4_SET_4_BIT_INTERFACE); // now force into 4-bit mode // writeCommand(CMD_NULL); // writeCommand(CMD_NULL); // writeCommand(CMD_NULL); // writeCommand(CMD_NULL); // writeCommand(CMD_NULL); writeCommand(CMD_FUNCTION_SET | INTERFACE_4_BIT | TWO_LINE_DISPLAY | FONT_5x8 | ENGL_JAPAN_FONT_SET); // 0x28 writeCommand(CMD_DISPLAY_CONTROL | DISPLAY_ON | CURSOR_OFF | CURSOR_CHAR_BLINK_OFF); // 0xC0 cls(); writeCommand(CMD_RETURN_HOME); writeCommand(CMD_ENTRY_MODE | CURSOR_STEP_RIGHT | DISPLAY_SHIFT_OFF ); // 0x06 } int WattBob_TextLCD::_putc(int value) { if(value == '\n') { newline(); } else { writeData(value); } return value; } int WattBob_TextLCD::_getc() { return 0; } void WattBob_TextLCD::newline() { _column = 0; _row++; if(_row >= _rows) { _row = 0; } locate(_column, _row); } void WattBob_TextLCD::locate(int row, int column) { if(column < 0 || column >= _columns || row < 0 || row >= _rows) { // error("locate(%d,%d) out of range on %dx%d display", column, row, _columns, _rows); return; } _row = row; _column = column; int address = 0x80 + (_row * 0x40) + _column; // memory starts at 0x80, and internally it is 40 chars per row (only first 16 used) writeCommand(address); } void WattBob_TextLCD::cls() { writeCommand(CMD_CLEAR_DISPLAY); // 0x01 wait(DISPLAY_CLEAR_DELAY); // locate(0, 0); } void WattBob_TextLCD::reset() { cls(); } void WattBob_TextLCD::clock() { wait(0.000040f); _e(1); wait(0.000040f); // most instructions take 40us _e(0); } void WattBob_TextLCD::writeNibble(int value) { _d(value); clock(); } void WattBob_TextLCD::writeByte(int value) { writeNibble((value >> 4) & 0x000F); writeNibble((value >> 0) & 0x000F); } void WattBob_TextLCD::writeCommand(int command) { _rs(0); writeByte(command); } void WattBob_TextLCD::writeData(int data) { _rs(1); writeByte(data); _column++; if(_column >= _columns) { newline(); } } void WattBob_TextLCD::_rs(int data) { par_port->write_bit(data, RS_BIT); } void WattBob_TextLCD::_rw(int data) { par_port->write_bit(data, RW_BIT); } void WattBob_TextLCD::_e(int data) { par_port->write_bit(data, E_BIT); } void WattBob_TextLCD::_d(int data) { par_port->write_mask((unsigned short)data, (unsigned short)0x000F); }