Nothing Special / mbed-STM32F103C8

Modification of Mbed-dev library for LQFP48 package microcontrollers: STM32F103C8 (STM32F103C8T6) and STM32F103CB (STM32F103CBT6) (Bluepill boards, Maple mini etc. )

Fork of mbed-STM32F103C8_org by Nothing Special

Library for STM32F103C8 (Bluepill boards etc.).
Use this instead of mbed library.
This library allows the size of the code in the FLASH up to 128kB. Therefore, code also runs on microcontrollers STM32F103CB (eg. Maple mini).
But in the case of STM32F103C8, check the size of the resulting code would not exceed 64kB.

To compile a program with this library, use NUCLEO-F103RB as the target name. !

Changes:

  • Corrected initialization of the HSE + crystal clock (mbed permanent bug), allowing the use of on-board xtal (8MHz).(1)
  • Additionally, it also set USB clock (48Mhz).(2)
  • Definitions of pins and peripherals adjusted to LQFP48 case.
  • Board led LED1 is now PC_13 (3)
  • USER_BUTTON is now PC_14 (4)

    Now the library is complete rebuilt based on mbed-dev v160 (and not yet fully tested).

notes
(1) - In case 8MHz xtal on board, CPU frequency is 72MHz. Without xtal is 64MHz.
(2) - Using the USB interface is only possible if STM32 is clocking by on-board 8MHz xtal or external clock signal 8MHz on the OSC_IN pin.
(3) - On Bluepill board led operation is reversed, i.e. 0 - led on, 1 - led off.
(4) - Bluepill board has no real user button

Information

After export to SW4STM (AC6):

  • add line #include "mbed_config.h" in files Serial.h and RawSerial.h
  • in project properties change Optimisation Level to Optimise for size (-Os)

hal/sleep_api.h

Committer:
mega64
Date:
2017-04-27
Revision:
148:8b0b02bf146f
Parent:
147:38a0c20c7b3e

File content as of revision 148:8b0b02bf146f:


/** \addtogroup hal */
/** @{*/
/* mbed Microcontroller Library
 * Copyright (c) 2006-2013 ARM Limited
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */
#ifndef MBED_SLEEP_API_H
#define MBED_SLEEP_API_H

#include "device.h"

#if DEVICE_SLEEP

#ifdef __cplusplus
extern "C" {
#endif

/** Send the microcontroller to sleep
 *
 * The processor is setup ready for sleep, and sent to sleep using __WFI(). In this mode, the
 * system clock to the core is stopped until a reset or an interrupt occurs. This eliminates
 * dynamic power used by the processor, memory systems and buses. The processor, peripheral and
 * memory state are maintained, and the peripherals continue to work and can generate interrupts.
 *
 * The processor can be woken up by any internal peripheral interrupt or external pin interrupt.
 *
 * @note
 *  The mbed interface semihosting is disconnected as part of going to sleep, and can not be restored.
 * Flash re-programming and the USB serial port will remain active, but the mbed program will no longer be
 * able to access the LocalFileSystem
 */
void hal_sleep(void);

/** Send the microcontroller to deep sleep
 *
 * This processor is setup ready for deep sleep, and sent to sleep using __WFI(). This mode
 * has the same sleep features as sleep plus it powers down peripherals and clocks. All state
 * is still maintained.
 *
 * The processor can only be woken up by an external interrupt on a pin or a watchdog timer.
 *
 * @note
 *  The mbed interface semihosting is disconnected as part of going to sleep, and can not be restored.
 * Flash re-programming and the USB serial port will remain active, but the mbed program will no longer be
 * able to access the LocalFileSystem
 */
void hal_deepsleep(void);

#ifdef __cplusplus
}
#endif

#endif

#endif

/** @}*/