Nothing Special / mbed-STM32F103C8

Modification of Mbed-dev library for LQFP48 package microcontrollers: STM32F103C8 (STM32F103C8T6) and STM32F103CB (STM32F103CBT6) (Bluepill boards, Maple mini etc. )

Fork of mbed-STM32F103C8_org by Nothing Special

Library for STM32F103C8 (Bluepill boards etc.).
Use this instead of mbed library.
This library allows the size of the code in the FLASH up to 128kB. Therefore, code also runs on microcontrollers STM32F103CB (eg. Maple mini).
But in the case of STM32F103C8, check the size of the resulting code would not exceed 64kB.

To compile a program with this library, use NUCLEO-F103RB as the target name. !

Changes:

  • Corrected initialization of the HSE + crystal clock (mbed permanent bug), allowing the use of on-board xtal (8MHz).(1)
  • Additionally, it also set USB clock (48Mhz).(2)
  • Definitions of pins and peripherals adjusted to LQFP48 case.
  • Board led LED1 is now PC_13 (3)
  • USER_BUTTON is now PC_14 (4)

    Now the library is complete rebuilt based on mbed-dev v160 (and not yet fully tested).

notes
(1) - In case 8MHz xtal on board, CPU frequency is 72MHz. Without xtal is 64MHz.
(2) - Using the USB interface is only possible if STM32 is clocking by on-board 8MHz xtal or external clock signal 8MHz on the OSC_IN pin.
(3) - On Bluepill board led operation is reversed, i.e. 0 - led on, 1 - led off.
(4) - Bluepill board has no real user button

Information

After export to SW4STM (AC6):

  • add line #include "mbed_config.h" in files Serial.h and RawSerial.h
  • in project properties change Optimisation Level to Optimise for size (-Os)

hal/gpio_irq_api.h

Committer:
mega64
Date:
2017-04-27
Revision:
148:8b0b02bf146f
Parent:
147:38a0c20c7b3e

File content as of revision 148:8b0b02bf146f:


/** \addtogroup hal */
/** @{*/
/* mbed Microcontroller Library
 * Copyright (c) 2006-2013 ARM Limited
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */
#ifndef MBED_GPIO_IRQ_API_H
#define MBED_GPIO_IRQ_API_H

#include "device.h"

#if DEVICE_INTERRUPTIN

#ifdef __cplusplus
extern "C" {
#endif

/** GPIO IRQ events
 */
typedef enum {
    IRQ_NONE,
    IRQ_RISE,
    IRQ_FALL
} gpio_irq_event;

/** GPIO IRQ HAL structure. gpio_irq_s is declared in the target's HAL
 */
typedef struct gpio_irq_s gpio_irq_t;

typedef void (*gpio_irq_handler)(uint32_t id, gpio_irq_event event);

/**
 * \defgroup hal_gpioirq GPIO IRQ HAL functions
 * @{
 */

/** Initialize the GPIO IRQ pin
 *
 * @param obj     The GPIO object to initialize
 * @param pin     The GPIO pin name
 * @param handler The handler to be attached to GPIO IRQ
 * @param id      The object ID (id != 0, 0 is reserved)
 * @return -1 if pin is NC, 0 otherwise
 */
int gpio_irq_init(gpio_irq_t *obj, PinName pin, gpio_irq_handler handler, uint32_t id);

/** Release the GPIO IRQ PIN
 *
 * @param obj The gpio object
 */
void gpio_irq_free(gpio_irq_t *obj);

/** Enable/disable pin IRQ event
 *
 * @param obj    The GPIO object
 * @param event  The GPIO IRQ event
 * @param enable The enable flag
 */
void gpio_irq_set(gpio_irq_t *obj, gpio_irq_event event, uint32_t enable);

/** Enable GPIO IRQ
 *
 * This is target dependent, as it might enable the entire port or just a pin
 * @param obj The GPIO object
 */
void gpio_irq_enable(gpio_irq_t *obj);

/** Disable GPIO IRQ
 *
 * This is target dependent, as it might disable the entire port or just a pin
 * @param obj The GPIO object
 */
void gpio_irq_disable(gpio_irq_t *obj);

/**@}*/

#ifdef __cplusplus
}
#endif

#endif

#endif

/** @}*/