This is a library that drives a stepper motor with given parameters for speed and direction.
About
This is a stepper motor library that is based on the sMotor library by Samuel Matildes (sam.naeec@gmail.com). It was designed to drive specifically a 5718m-05e-05 stepper motor in conjunction with an L293NE quad h-bridge chip. I am not responsible for any damage caused due to the execution of this program on your hardware as I can only confirm that it works for the above specified model. High torque mode is currently not complete.
mMotor.cpp
- Committer:
- mdu7078
- Date:
- 2013-04-24
- Revision:
- 0:acf5b8fc382b
- Child:
- 1:6e0a307d0f9b
File content as of revision 0:acf5b8fc382b:
/* * * * * * * * * * * * * * * * * * * * * * * * * * * * This is a stepper motor library for testing * * 4 step stepper motors. The speed of stepping is * * variable as well as the amount of steps. * * ------------------------------------------------- * * This library is based on the sMotor library by * * Samuel Matildes (sam.naeec@gmail.com). * * ------------------------------------------------- * * * * Created by: Michael Dushkoff (mad1841@rit.edu) * * * * * * * * * * * * * * * * * * * * * * * * * * * */ #include "mbed.h" #include "mMotor.h" int motorSpeed; // Steper speed mMotor::mMotor(PinName M0, PinName M1, PinName M2, PinName M3) : _M0(M0), _M1(M1), _M2(M2), _M3(M3) { // Defenition of motor pins _M0=0; _M1=0; _M2=0; _M3=0; } void mMotor::counterclockwise() { // rotate the motor 1 step anticlockwise for (int i = 0; i < 4; i++) { switch (i) { // activate the ports A0, A2, A3, A3 in a binary sequence for steps case 0: { _M0=0; _M1=0; _M2=0; _M3=1; } break; case 1: { _M0=0; _M1=0; _M2=1; _M3=0; } break; case 2: { _M0=0; _M1=1; _M2=0; _M3=0; } break; case 3: { _M0=1; _M1=0; _M2=0; _M3=0; } break; } wait_us(motorSpeed); // wait time defines the speed } } void mMotor::clockwise() { // rotate the motor 1 step clockwise for (int i = 0; i < 4; i++) { switch (i) { // activate the ports A0, A2, A3, A3 in a binary sequence for steps case 0: { _M0=1; _M1=0; _M2=0; _M3=0; } break; case 1: { _M0=0; _M1=1; _M2=0; _M3=0; } break; case 2: { _M0=0; _M1=0; _M2=1; _M3=0; } break; case 3: { _M0=0; _M1=0; _M2=0; _M3=1; } break; } wait_us(motorSpeed); // wait time defines the speed } } void mMotor::step(int num_steps, int direction, int speed) {// steper function: number of steps, direction (0- right, 1- left), speed (default 1200) int count=0; // initalize step count motorSpeed=speed; //set motor speed if (direction==0) // turn clockwise do { clockwise(); count++; } while (count<num_steps); // turn number of steps applied else if (direction==1)// turn anticlockwise do { counterclockwise(); count++; } while (count<num_steps);// turn number of steps applied }