Diff: TARGET_DISCO_L053C8/stm32l0xx_hal_pwr.h

Revision:

99:dbbf35b96557

Child:

119:aae6fcc7d9bb

diff -r 8ab26030e058 -r dbbf35b96557 TARGET_DISCO_L053C8/stm32l0xx_hal_pwr.h
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/TARGET_DISCO_L053C8/stm32l0xx_hal_pwr.h	Wed May 13 08:08:21 2015 +0200
@@ -0,0 +1,448 @@
+/**
+  ******************************************************************************
+  * @file    stm32l0xx_hal_pwr.h
+  * @author  MCD Application Team
+  * @version V1.2.0
+  * @date    06-February-2015
+  * @brief   Header file of PWR HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_PWR_H
+#define __STM32L0xx_HAL_PWR_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup PWR
+  * @{
+  */
+
+/** @defgroup PWR_Exported_Types PWR Exported Types
+  * @{
+  */ 
+
+/**
+  * @brief  PWR PVD configuration structure definition
+  */
+typedef struct
+{
+  uint32_t PVDLevel;   /*!< PVDLevel: Specifies the PVD detection level.
+                            This parameter can be a value of @ref PWR_PVD_detection_level */
+
+  uint32_t Mode;       /*!< Mode: Specifies the operating mode for the selected pins.
+                            This parameter can be a value of @ref PWR_PVD_Mode */
+}PWR_PVDTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Private_Defines PWR Private Defines
+  * @{
+  */ 
+
+#define PWR_EXTI_LINE_PVD      EXTI_FTSR_TR16  /*!< External interrupt line 16 Connected to the PVD EXTI Line */
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Exported_Constants PWR Exported Constants
+  * @{
+  */
+
+/** @defgroup PWR_register_alias_address PWR Register alias address
+  * @{
+  */
+#define PWR_WAKEUP_PIN1                PWR_CSR_EWUP1
+#define PWR_WAKEUP_PIN2                PWR_CSR_EWUP2
+#if defined (STM32L071xx) || defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+#define PWR_WAKEUP_PIN3                PWR_CSR_EWUP3
+#endif
+/**
+  * @}
+  */
+
+/** @defgroup PWR_PVD_detection_level PVD detection level
+  * @{
+  */
+#define PWR_PVDLEVEL_0                 PWR_CR_PLS_LEV0
+#define PWR_PVDLEVEL_1                 PWR_CR_PLS_LEV1
+#define PWR_PVDLEVEL_2                 PWR_CR_PLS_LEV2
+#define PWR_PVDLEVEL_3                 PWR_CR_PLS_LEV3
+#define PWR_PVDLEVEL_4                 PWR_CR_PLS_LEV4
+#define PWR_PVDLEVEL_5                 PWR_CR_PLS_LEV5
+#define PWR_PVDLEVEL_6                 PWR_CR_PLS_LEV6
+#define PWR_PVDLEVEL_7                 PWR_CR_PLS_LEV7  /* External input analog voltage 
+                                                           (Compare internally to VREFINT) */
+/**
+  * @}
+  */
+
+/** @defgroup PWR_PVD_Mode PWR PVD Mode
+  * @{
+  */
+#define PWR_PVD_MODE_NORMAL                 ((uint32_t)0x00000000)   /*!< basic mode is used */
+#define PWR_PVD_MODE_IT_RISING              ((uint32_t)0x00010001)   /*!< External Interrupt Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_IT_FALLING             ((uint32_t)0x00010002)   /*!< External Interrupt Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_IT_RISING_FALLING      ((uint32_t)0x00010003)   /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING           ((uint32_t)0x00020001)   /*!< Event Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_EVENT_FALLING          ((uint32_t)0x00020002)   /*!< Event Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING_FALLING   ((uint32_t)0x00020003)   /*!< Event Mode with Rising/Falling edge trigger detection */
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR Regulator state in SLEEP/STOP mode
+  * @{
+  */
+#define PWR_MAINREGULATOR_ON           ((uint32_t)0x00000000)
+#define PWR_LOWPOWERREGULATOR_ON       PWR_CR_LPSDSR
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
+  * @{
+  */
+#define PWR_SLEEPENTRY_WFI             ((uint8_t)0x01)
+#define PWR_SLEEPENTRY_WFE             ((uint8_t)0x02)
+/**
+  * @}
+  */
+
+/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
+  * @{
+  */
+#define PWR_STOPENTRY_WFI              ((uint8_t)0x01)
+#define PWR_STOPENTRY_WFE              ((uint8_t)0x02)
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Regulator_Voltage_Scale PWR Regulator Voltage Scale
+  * @{
+  */
+
+#define PWR_REGULATOR_VOLTAGE_SCALE1   PWR_CR_VOS_0
+#define PWR_REGULATOR_VOLTAGE_SCALE2   PWR_CR_VOS_1
+#define PWR_REGULATOR_VOLTAGE_SCALE3   PWR_CR_VOS
+
+#define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
+                                             ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \
+                                             ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE3))
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Flag PWR Flag
+  * @{
+  */
+#define PWR_FLAG_WU                    PWR_CSR_WUF
+#define PWR_FLAG_SB                    PWR_CSR_SBF
+#define PWR_FLAG_PVDO                  PWR_CSR_PVDO
+#define PWR_FLAG_VREFINTRDY            PWR_CSR_VREFINTRDYF
+#define PWR_FLAG_VOS                   PWR_CSR_VOSF
+#define PWR_FLAG_REGLP                 PWR_CSR_REGLPF
+
+#define IS_PWR_GET_FLAG(FLAG) (((FLAG) == PWR_FLAG_WU) || ((FLAG) == PWR_FLAG_SB) || \
+                               ((FLAG) == PWR_FLAG_PVDO) || ((FLAG) == PWR_FLAG_VREFINTRDY) || \
+                               ((FLAG) == PWR_FLAG_VOS) || ((FLAG) == PWR_FLAG_REGLP))
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Exported_Macro PWR Exported Macro
+  * @{
+  */
+/** @brief  macros configure the main internal regulator output voltage.
+  * @param  __REGULATOR__: specifies the regulator output voltage to achieve
+  *         a tradeoff between performance and power consumption when the device does
+  *         not operate at the maximum frequency (refer to the datasheets for more details).
+  *          This parameter can be one of the following values:
+  *            @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode,
+  *                                                System frequency up to 32 MHz.
+  *            @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode,
+  *                                                System frequency up to 16 MHz.
+  *            @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode,
+  *                                                System frequency up to 4.2 MHz
+  * @retval None
+  */
+#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) (MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)))
+
+/** @brief  Check PWR flag is set or not.
+  * @param  __FLAG__: specifies the flag to check.
+  *           This parameter can be one of the following values:
+  *            @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
+  *                  was received from the WKUP pin or from the RTC alarm (Alarm B),
+  *                  RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
+  *                  An additional wakeup event is detected if the WKUP pin is enabled
+  *                  (by setting the EWUP bit) when the WKUP pin level is already high.
+  *            @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
+  *                  resumed from StandBy mode.
+  *            @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled 
+  *                  by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode.
+  *                  For this reason, this bit is equal to 0 after Standby or reset
+  *                  until the PVDE bit is set.
+  *            @arg PWR_FLAG_VREFINTRDY: Internal voltage reference (VREFINT) ready flag.
+  *                 This bit indicates the state of the internal voltage reference, VREFINT.
+  *            @arg PWR_FLAG_VOS: Voltage Scaling select flag. A delay is required for
+  *                 the internal regulator to be ready after the voltage range is changed.
+  *                 The VOSF bit indicates that the regulator has reached the voltage level
+  *                 defined with bits VOS of PWR_CR register.
+  *            @arg PWR_FLAG_REGLP: Regulator LP flag. When the MCU exits from Low power run
+  *                 mode, this bit stays at 1 until the regulator is ready in main mode.
+  *                 A polling on this bit is recommended to wait for the regulator main mode.
+  *                 This bit is reset by hardware when the regulator is ready.
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_PWR_GET_FLAG(__FLAG__)                  ((PWR->CSR & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clear the PWR's pending flags.
+  * @param  __FLAG__: specifies the flag to clear.
+  *          This parameter can be one of the following values:
+  *            @arg PWR_FLAG_WU: Wake Up flag
+  *            @arg PWR_FLAG_SB: StandBy flag
+  */
+#define __HAL_PWR_CLEAR_FLAG(__FLAG__)                SET_BIT(PWR->CR, (__FLAG__) << 2)
+
+/**
+  * @brief Enable interrupt on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_IT()      SET_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable interrupt on PVD Exti Line 16. 
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_IT()     CLEAR_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Enable event on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT()   SET_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable event on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT()  CLEAR_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
+
+
+/**
+  * @brief  PVD EXTI line configuration: set falling edge trigger.  
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE()  SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+
+/**
+  * @brief Disable the PVD Extended Interrupt Falling Trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE()  CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+
+/**
+  * @brief  PVD EXTI line configuration: set rising edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE()   SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable the PVD Extended Interrupt Rising Trigger.
+  * This parameter can be:
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE()  CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief  PVD EXTI line configuration: set rising & falling edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE()   __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();
+
+/**
+  * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger.
+  * This parameter can be:
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE()  __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE()();
+
+
+
+/**
+  * @brief Check whether the specified PVD EXTI interrupt flag is set or not.
+  * @retval EXTI PVD Line Status.
+  */
+#define __HAL_PWR_PVD_EXTI_GET_FLAG()       (EXTI->PR & (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Clear the PVD EXTI flag.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG()     (EXTI->PR = (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Generate a Software interrupt on selected EXTI line.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT()  SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)
+/**
+  * @}
+  */
+
+/**
+  * @brief Generate a Software interrupt on selected EXTI line.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT()            SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Private_Macros PWR Private Macros
+  * @{
+  */
+#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7))
+
+#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \
+                              ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \
+                              ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \
+                              ((MODE) == PWR_PVD_MODE_NORMAL)) 
+
+#if defined (STM32L071xx) || defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+                                ((PIN) == PWR_WAKEUP_PIN2) || \
+                                ((PIN) == PWR_WAKEUP_PIN3))
+#else
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+                                ((PIN) == PWR_WAKEUP_PIN2))
+#endif
+
+#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
+                                     ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))
+#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))
+
+#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE))
+
+/**
+  * @}
+  */
+
+/* Include PWR HAL Extension module */
+#include "stm32l0xx_hal_pwr_ex.h"
+
+/** @defgroup PWR_Exported_Functions PWR Exported Functions
+  * @{
+  */
+  
+/** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions 
+  * @{
+  */
+void HAL_PWR_DeInit(void);
+void HAL_PWR_EnableBkUpAccess(void);
+void HAL_PWR_DisableBkUpAccess(void);
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Exported_Functions_Group2 Low Power modes configuration functions
+  * @{
+  */
+
+/* PVD control functions  ************************************************/
+void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD);
+void HAL_PWR_EnablePVD(void);
+void HAL_PWR_DisablePVD(void);
+void HAL_PWR_PVD_IRQHandler(void);
+void HAL_PWR_PVDCallback(void);
+
+/* WakeUp pins configuration functions ****************************************/
+void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx);
+void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);
+
+/* Low Power modes configuration functions ************************************/
+void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
+void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
+void HAL_PWR_EnterSTANDBYMode(void);
+
+void HAL_PWR_EnableSleepOnExit(void);
+void HAL_PWR_DisableSleepOnExit(void);
+void HAL_PWR_EnableSEVOnPend(void);
+void HAL_PWR_DisableSEVOnPend(void);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* __STM32L0xx_HAL_PWR_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+