The official Mbed 2 C/C++ SDK provides the software platform and libraries to build your applications.
Dependents: hello SerialTestv11 SerialTestv12 Sierpinski ... more
mbed 2
This is the mbed 2 library. If you'd like to learn about Mbed OS please see the mbed-os docs.
TARGET_NUCLEO_F334R8/stm32f3xx_hal_uart.h
- Committer:
- Kojto
- Date:
- 2016-08-12
- Revision:
- 123:b0220dba8be7
- Parent:
- 122:f9eeca106725
File content as of revision 123:b0220dba8be7:
/** ****************************************************************************** * @file stm32f3xx_hal_uart.h * @author MCD Application Team * @version V1.3.0 * @date 01-July-2016 * @brief Header file of UART HAL module. ****************************************************************************** * @attention * * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: * 1. Redistributions of source code must retain the above copyright notice, * this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright notice, * this list of conditions and the following disclaimer in the documentation * and/or other materials provided with the distribution. * 3. Neither the name of STMicroelectronics nor the names of its contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ****************************************************************************** */ /* Define to prevent recursive inclusion -------------------------------------*/ #ifndef __STM32F3xx_HAL_UART_H #define __STM32F3xx_HAL_UART_H #ifdef __cplusplus extern "C" { #endif /* Includes ------------------------------------------------------------------*/ #include "stm32f3xx_hal_def.h" /** @addtogroup STM32F3xx_HAL_Driver * @{ */ /** @addtogroup UART * @{ */ /* Exported types ------------------------------------------------------------*/ /** @defgroup UART_Exported_Types UART Exported Types * @{ */ /** * @brief UART Init Structure definition */ typedef struct { uint32_t BaudRate; /*!< This member configures the UART communication baud rate. The baud rate register is computed using the following formula: - If oversampling is 16 or in LIN mode, Baud Rate Register = ((PCLKx) / ((huart->Init.BaudRate))) - If oversampling is 8, Baud Rate Register[15:4] = ((2 * PCLKx) / ((huart->Init.BaudRate)))[15:4] Baud Rate Register[3] = 0 Baud Rate Register[2:0] = (((2 * PCLKx) / ((huart->Init.BaudRate)))[3:0]) >> 1 */ uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame. This parameter can be a value of @ref UARTEx_Word_Length */ uint32_t StopBits; /*!< Specifies the number of stop bits transmitted. This parameter can be a value of @ref UART_Stop_Bits */ uint32_t Parity; /*!< Specifies the parity mode. This parameter can be a value of @ref UART_Parity @note When parity is enabled, the computed parity is inserted at the MSB position of the transmitted data (9th bit when the word length is set to 9 data bits; 8th bit when the word length is set to 8 data bits). */ uint32_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled. This parameter can be a value of @ref UART_Mode */ uint32_t HwFlowCtl; /*!< Specifies whether the hardware flow control mode is enabled or disabled. This parameter can be a value of @ref UART_Hardware_Flow_Control */ uint32_t OverSampling; /*!< Specifies whether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to f_PCLK/8). This parameter can be a value of @ref UART_Over_Sampling */ uint32_t OneBitSampling; /*!< Specifies whether a single sample or three samples' majority vote is selected. Selecting the single sample method increases the receiver tolerance to clock deviations. This parameter can be a value of @ref UART_OneBit_Sampling. */ }UART_InitTypeDef; /** * @brief UART Advanced Features initalization structure definition */ typedef struct { uint32_t AdvFeatureInit; /*!< Specifies which advanced UART features is initialized. Several Advanced Features may be initialized at the same time . This parameter can be a value of @ref UART_Advanced_Features_Initialization_Type */ uint32_t TxPinLevelInvert; /*!< Specifies whether the TX pin active level is inverted. This parameter can be a value of @ref UART_Tx_Inv */ uint32_t RxPinLevelInvert; /*!< Specifies whether the RX pin active level is inverted. This parameter can be a value of @ref UART_Rx_Inv */ uint32_t DataInvert; /*!< Specifies whether data are inverted (positive/direct logic vs negative/inverted logic). This parameter can be a value of @ref UART_Data_Inv */ uint32_t Swap; /*!< Specifies whether TX and RX pins are swapped. This parameter can be a value of @ref UART_Rx_Tx_Swap */ uint32_t OverrunDisable; /*!< Specifies whether the reception overrun detection is disabled. This parameter can be a value of @ref UART_Overrun_Disable */ uint32_t DMADisableonRxError; /*!< Specifies whether the DMA is disabled in case of reception error. This parameter can be a value of @ref UART_DMA_Disable_on_Rx_Error */ uint32_t AutoBaudRateEnable; /*!< Specifies whether auto Baud rate detection is enabled. This parameter can be a value of @ref UART_AutoBaudRate_Enable */ uint32_t AutoBaudRateMode; /*!< If auto Baud rate detection is enabled, specifies how the rate detection is carried out. This parameter can be a value of @ref UART_AutoBaud_Rate_Mode */ uint32_t MSBFirst; /*!< Specifies whether MSB is sent first on UART line. This parameter can be a value of @ref UART_MSB_First */ } UART_AdvFeatureInitTypeDef; /** * @brief UART wake up from stop mode parameters */ typedef struct { uint32_t WakeUpEvent; /*!< Specifies which event will activat the Wakeup from Stop mode flag (WUF). This parameter can be a value of @ref UART_WakeUp_from_Stop_Selection. If set to UART_WAKEUP_ON_ADDRESS, the two other fields below must be filled up. */ uint16_t AddressLength; /*!< Specifies whether the address is 4 or 7-bit long. This parameter can be a value of @ref UART_WakeUp_Address_Length */ uint8_t Address; /*!< UART/USART node address (7-bit long max) */ } UART_WakeUpTypeDef; /** * @brief HAL UART State structures definition * @note HAL UART State value is a combination of 2 different substates: gState and RxState. * - gState contains UART state information related to global Handle management * and also information related to Tx operations. * gState value coding follow below described bitmap : * b7-b6 Error information * 00 : No Error * 01 : (Not Used) * 10 : Timeout * 11 : Error * b5 IP initilisation status * 0 : Reset (IP not initialized) * 1 : Init done (IP not initialized. HAL UART Init function already called) * b4-b3 (not used) * xx : Should be set to 00 * b2 Intrinsic process state * 0 : Ready * 1 : Busy (IP busy with some configuration or internal operations) * b1 (not used) * x : Should be set to 0 * b0 Tx state * 0 : Ready (no Tx operation ongoing) * 1 : Busy (Tx operation ongoing) * - RxState contains information related to Rx operations. * RxState value coding follow below described bitmap : * b7-b6 (not used) * xx : Should be set to 00 * b5 IP initilisation status * 0 : Reset (IP not initialized) * 1 : Init done (IP not initialized) * b4-b2 (not used) * xxx : Should be set to 000 * b1 Rx state * 0 : Ready (no Rx operation ongoing) * 1 : Busy (Rx operation ongoing) * b0 (not used) * x : Should be set to 0. */ typedef enum { HAL_UART_STATE_RESET = 0x00U, /*!< Peripheral is not initialized Value is allowed for gState and RxState */ HAL_UART_STATE_READY = 0x20U, /*!< Peripheral Initialized and ready for use Value is allowed for gState and RxState */ HAL_UART_STATE_BUSY = 0x24U, /*!< an internal process is ongoing Value is allowed for gState only */ HAL_UART_STATE_BUSY_TX = 0x21U, /*!< Data Transmission process is ongoing Value is allowed for gState only */ HAL_UART_STATE_BUSY_RX = 0x22U, /*!< Data Reception process is ongoing Value is allowed for RxState only */ HAL_UART_STATE_BUSY_TX_RX = 0x23U, /*!< Data Transmission and Reception process is ongoing Not to be used for neither gState nor RxState. Value is result of combination (Or) between gState and RxState values */ HAL_UART_STATE_TIMEOUT = 0xA0U, /*!< Timeout state Value is allowed for gState only */ HAL_UART_STATE_ERROR = 0xE0U /*!< Error Value is allowed for gState only */ }HAL_UART_StateTypeDef; /** * @brief UART clock sources definition */ typedef enum { UART_CLOCKSOURCE_PCLK1 = 0x00, /*!< PCLK1 clock source */ UART_CLOCKSOURCE_PCLK2 = 0x01, /*!< PCLK2 clock source */ UART_CLOCKSOURCE_HSI = 0x02, /*!< HSI clock source */ UART_CLOCKSOURCE_SYSCLK = 0x04, /*!< SYSCLK clock source */ UART_CLOCKSOURCE_LSE = 0x08, /*!< LSE clock source */ UART_CLOCKSOURCE_UNDEFINED = 0x10 /*!< Undefined clock source */ }UART_ClockSourceTypeDef; /** * @brief UART handle Structure definition */ typedef struct { USART_TypeDef *Instance; /*!< UART registers base address */ UART_InitTypeDef Init; /*!< UART communication parameters */ UART_AdvFeatureInitTypeDef AdvancedInit; /*!< UART Advanced Features initialization parameters */ uint8_t *pTxBuffPtr; /*!< Pointer to UART Tx transfer Buffer */ uint16_t TxXferSize; /*!< UART Tx Transfer size */ uint16_t TxXferCount; /*!< UART Tx Transfer Counter */ uint8_t *pRxBuffPtr; /*!< Pointer to UART Rx transfer Buffer */ uint16_t RxXferSize; /*!< UART Rx Transfer size */ uint16_t RxXferCount; /*!< UART Rx Transfer Counter */ uint16_t Mask; /*!< UART Rx RDR register mask */ DMA_HandleTypeDef *hdmatx; /*!< UART Tx DMA Handle parameters */ DMA_HandleTypeDef *hdmarx; /*!< UART Rx DMA Handle parameters */ HAL_LockTypeDef Lock; /*!< Locking object */ __IO HAL_UART_StateTypeDef gState; /*!< UART state information related to global Handle management and also related to Tx operations. This parameter can be a value of @ref HAL_UART_StateTypeDef */ __IO HAL_UART_StateTypeDef RxState; /*!< UART state information related to Rx operations. This parameter can be a value of @ref HAL_UART_StateTypeDef */ __IO uint32_t ErrorCode; /*!< UART Error code */ }UART_HandleTypeDef; /** * @} */ /* Exported constants --------------------------------------------------------*/ /** @defgroup UART_Exported_Constants UART Exported Constants * @{ */ /** @defgroup UART_Error UART Error * @{ */ #define HAL_UART_ERROR_NONE ((uint32_t)0x00000000) /*!< No error */ #define HAL_UART_ERROR_PE ((uint32_t)0x00000001) /*!< Parity error */ #define HAL_UART_ERROR_NE ((uint32_t)0x00000002) /*!< Noise error */ #define HAL_UART_ERROR_FE ((uint32_t)0x00000004) /*!< frame error */ #define HAL_UART_ERROR_ORE ((uint32_t)0x00000008) /*!< Overrun error */ #define HAL_UART_ERROR_DMA ((uint32_t)0x00000010) /*!< DMA transfer error */ /** * @} */ /** @defgroup UART_Stop_Bits UART Number of Stop Bits * @{ */ #define UART_STOPBITS_0_5 USART_CR2_STOP_0 /*!< UART frame with 0.5 stop bit */ #define UART_STOPBITS_1 ((uint32_t)0x00000000) /*!< UART frame with 1 stop bit */ #define UART_STOPBITS_1_5 ((uint32_t)(USART_CR2_STOP_0 | USART_CR2_STOP_1)) /*!< UART frame with 1.5 stop bits */ #define UART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1) /*!< UART frame with 2 stop bits */ /** * @} */ /** @defgroup UART_Parity UART Parity * @{ */ #define UART_PARITY_NONE ((uint32_t)0x00000000) /*!< No parity */ #define UART_PARITY_EVEN ((uint32_t)USART_CR1_PCE) /*!< Even parity */ #define UART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS)) /*!< Odd parity */ /** * @} */ /** @defgroup UART_Hardware_Flow_Control UART Hardware Flow Control * @{ */ #define UART_HWCONTROL_NONE ((uint32_t)0x00000000) /*!< No hardware control */ #define UART_HWCONTROL_RTS ((uint32_t)USART_CR3_RTSE) /*!< Request To Send */ #define UART_HWCONTROL_CTS ((uint32_t)USART_CR3_CTSE) /*!< Clear To Send */ #define UART_HWCONTROL_RTS_CTS ((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE)) /*!< Request and Clear To Send */ /** * @} */ /** @defgroup UART_Mode UART Transfer Mode * @{ */ #define UART_MODE_RX ((uint32_t)USART_CR1_RE) /*!< RX mode */ #define UART_MODE_TX ((uint32_t)USART_CR1_TE) /*!< TX mode */ #define UART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE)) /*!< RX and TX mode */ /** * @} */ /** @defgroup UART_State UART State * @{ */ #define UART_STATE_DISABLE ((uint32_t)0x00000000) /*!< UART disabled */ #define UART_STATE_ENABLE ((uint32_t)USART_CR1_UE) /*!< UART enabled */ /** * @} */ /** @defgroup UART_Over_Sampling UART Over Sampling * @{ */ #define UART_OVERSAMPLING_16 ((uint32_t)0x00000000) /*!< Oversampling by 16 */ #define UART_OVERSAMPLING_8 ((uint32_t)USART_CR1_OVER8) /*!< Oversampling by 8 */ /** * @} */ /** @defgroup UART_OneBit_Sampling UART One Bit Sampling Method * @{ */ #define UART_ONE_BIT_SAMPLE_DISABLE ((uint32_t)0x00000000) /*!< One-bit sampling disable */ #define UART_ONE_BIT_SAMPLE_ENABLE ((uint32_t)USART_CR3_ONEBIT) /*!< One-bit sampling enable */ /** * @} */ /** @defgroup UART_AutoBaud_Rate_Mode UART Advanced Feature AutoBaud Rate Mode * @{ */ #define UART_ADVFEATURE_AUTOBAUDRATE_ONSTARTBIT ((uint32_t)0x00000000) /*!< Auto Baud rate detection on start bit */ #define UART_ADVFEATURE_AUTOBAUDRATE_ONFALLINGEDGE ((uint32_t)USART_CR2_ABRMODE_0) /*!< Auto Baud rate detection on falling edge */ #define UART_ADVFEATURE_AUTOBAUDRATE_ON0X7FFRAME ((uint32_t)USART_CR2_ABRMODE_1) /*!< Auto Baud rate detection on 0x7F frame detection */ #define UART_ADVFEATURE_AUTOBAUDRATE_ON0X55FRAME ((uint32_t)USART_CR2_ABRMODE) /*!< Auto Baud rate detection on 0x55 frame detection */ /** * @} */ /** @defgroup UART_Receiver_TimeOut UART Receiver TimeOut * @{ */ #define UART_RECEIVER_TIMEOUT_DISABLE ((uint32_t)0x00000000) /*!< UART receiver timeout disable */ #define UART_RECEIVER_TIMEOUT_ENABLE ((uint32_t)USART_CR2_RTOEN) /*!< UART receiver timeout enable */ /** * @} */ /** @defgroup UART_LIN UART Local Interconnection Network mode * @{ */ #define UART_LIN_DISABLE ((uint32_t)0x00000000) /*!< Local Interconnect Network disable */ #define UART_LIN_ENABLE ((uint32_t)USART_CR2_LINEN) /*!< Local Interconnect Network enable */ /** * @} */ /** @defgroup UART_LIN_Break_Detection UART LIN Break Detection * @{ */ #define UART_LINBREAKDETECTLENGTH_10B ((uint32_t)0x00000000) /*!< LIN 10-bit break detection length */ #define UART_LINBREAKDETECTLENGTH_11B ((uint32_t)USART_CR2_LBDL) /*!< LIN 11-bit break detection length */ /** * @} */ /** @defgroup UART_DMA_Tx UART DMA Tx * @{ */ #define UART_DMA_TX_DISABLE ((uint32_t)0x00000000) /*!< UART DMA TX disabled */ #define UART_DMA_TX_ENABLE ((uint32_t)USART_CR3_DMAT) /*!< UART DMA TX enabled */ /** * @} */ /** @defgroup UART_DMA_Rx UART DMA Rx * @{ */ #define UART_DMA_RX_DISABLE ((uint32_t)0x00000000) /*!< UART DMA RX disabled */ #define UART_DMA_RX_ENABLE ((uint32_t)USART_CR3_DMAR) /*!< UART DMA RX enabled */ /** * @} */ /** @defgroup UART_Half_Duplex_Selection UART Half Duplex Selection * @{ */ #define UART_HALF_DUPLEX_DISABLE ((uint32_t)0x00000000) /*!< UART half-duplex disabled */ #define UART_HALF_DUPLEX_ENABLE ((uint32_t)USART_CR3_HDSEL) /*!< UART half-duplex enabled */ /** * @} */ /** @defgroup UART_WakeUp_Address_Length UART WakeUp Address Length * @{ */ #define UART_ADDRESS_DETECT_4B ((uint32_t)0x00000000) /*!< 4-bit long wake-up address */ #define UART_ADDRESS_DETECT_7B ((uint32_t)USART_CR2_ADDM7) /*!< 7-bit long wake-up address */ /** * @} */ /** @defgroup UART_WakeUp_Methods UART WakeUp Methods * @{ */ #define UART_WAKEUPMETHOD_IDLELINE ((uint32_t)0x00000000) /*!< UART wake-up on idle line */ #define UART_WAKEUPMETHOD_ADDRESSMARK ((uint32_t)USART_CR1_WAKE) /*!< UART wake-up on address mark */ /** * @} */ /** @defgroup UART_Flags UART Status Flags * Elements values convention: 0xXXXX * - 0xXXXX : Flag mask in the ISR register * @{ */ #define UART_FLAG_REACK ((uint32_t)0x00400000) #define UART_FLAG_TEACK ((uint32_t)0x00200000) #define UART_FLAG_WUF ((uint32_t)0x00100000) #define UART_FLAG_RWU ((uint32_t)0x00080000) #define UART_FLAG_SBKF ((uint32_t)0x00040000) #define UART_FLAG_CMF ((uint32_t)0x00020000) #define UART_FLAG_BUSY ((uint32_t)0x00010000) #define UART_FLAG_ABRF ((uint32_t)0x00008000) #define UART_FLAG_ABRE ((uint32_t)0x00004000) #define UART_FLAG_EOBF ((uint32_t)0x00001000) #define UART_FLAG_RTOF ((uint32_t)0x00000800) #define UART_FLAG_CTS ((uint32_t)0x00000400) #define UART_FLAG_CTSIF ((uint32_t)0x00000200) #define UART_FLAG_LBDF ((uint32_t)0x00000100) #define UART_FLAG_TXE ((uint32_t)0x00000080) #define UART_FLAG_TC ((uint32_t)0x00000040) #define UART_FLAG_RXNE ((uint32_t)0x00000020) #define UART_FLAG_IDLE ((uint32_t)0x00000010) #define UART_FLAG_ORE ((uint32_t)0x00000008) #define UART_FLAG_NE ((uint32_t)0x00000004) #define UART_FLAG_FE ((uint32_t)0x00000002) #define UART_FLAG_PE ((uint32_t)0x00000001) /** * @} */ /** @defgroup UART_Interrupt_definition UART Interrupts Definition * Elements values convention: 000ZZZZZ0XXYYYYYb * - YYYYY : Interrupt source position in the XX register (5bits) * - XX : Interrupt source register (2bits) * - 01: CR1 register * - 10: CR2 register * - 11: CR3 register * - ZZZZZ : Flag position in the ISR register(5bits) * @{ */ #define UART_IT_PE ((uint16_t)0x0028) #define UART_IT_TXE ((uint16_t)0x0727) #define UART_IT_TC ((uint16_t)0x0626) #define UART_IT_RXNE ((uint16_t)0x0525) #define UART_IT_IDLE ((uint16_t)0x0424) #define UART_IT_LBD ((uint16_t)0x0846) #define UART_IT_CTS ((uint16_t)0x096A) #define UART_IT_CM ((uint16_t)0x112E) #define UART_IT_WUF ((uint16_t)0x1476) /** Elements values convention: 000000000XXYYYYYb * - YYYYY : Interrupt source position in the XX register (5bits) * - XX : Interrupt source register (2bits) * - 01: CR1 register * - 10: CR2 register * - 11: CR3 register */ #define UART_IT_ERR ((uint16_t)0x0060) /** Elements values convention: 0000ZZZZ00000000b * - ZZZZ : Flag position in the ISR register(4bits) */ #define UART_IT_ORE ((uint16_t)0x0300) #define UART_IT_NE ((uint16_t)0x0200) #define UART_IT_FE ((uint16_t)0x0100) /** * @} */ /** @defgroup UART_IT_CLEAR_Flags UART Interruption Clear Flags * @{ */ #define UART_CLEAR_PEF USART_ICR_PECF /*!< Parity Error Clear Flag */ #define UART_CLEAR_FEF USART_ICR_FECF /*!< Framing Error Clear Flag */ #define UART_CLEAR_NEF USART_ICR_NCF /*!< Noise detected Clear Flag */ #define UART_CLEAR_OREF USART_ICR_ORECF /*!< OverRun Error Clear Flag */ #define UART_CLEAR_IDLEF USART_ICR_IDLECF /*!< IDLE line detected Clear Flag */ #define UART_CLEAR_TCF USART_ICR_TCCF /*!< Transmission Complete Clear Flag */ #define UART_CLEAR_LBDF USART_ICR_LBDCF /*!< LIN Break Detection Clear Flag */ #define UART_CLEAR_CTSF USART_ICR_CTSCF /*!< CTS Interrupt Clear Flag */ #define UART_CLEAR_RTOF USART_ICR_RTOCF /*!< Receiver Time Out Clear Flag */ #define UART_CLEAR_EOBF USART_ICR_EOBCF /*!< End Of Block Clear Flag */ #define UART_CLEAR_CMF USART_ICR_CMCF /*!< Character Match Clear Flag */ #define UART_CLEAR_WUF USART_ICR_WUCF /*!< Wake Up from stop mode Clear Flag */ /** * @} */ /** @defgroup UART_Request_Parameters UART Request Parameters * @{ */ #define UART_AUTOBAUD_REQUEST ((uint32_t)USART_RQR_ABRRQ) /*!< Auto-Baud Rate Request */ #define UART_SENDBREAK_REQUEST ((uint32_t)USART_RQR_SBKRQ) /*!< Send Break Request */ #define UART_MUTE_MODE_REQUEST ((uint32_t)USART_RQR_MMRQ) /*!< Mute Mode Request */ #define UART_RXDATA_FLUSH_REQUEST ((uint32_t)USART_RQR_RXFRQ) /*!< Receive Data flush Request */ #define UART_TXDATA_FLUSH_REQUEST ((uint32_t)USART_RQR_TXFRQ) /*!< Transmit data flush Request */ /** * @} */ /** @defgroup UART_Advanced_Features_Initialization_Type UART Advanced Feature Initialization Type * @{ */ #define UART_ADVFEATURE_NO_INIT ((uint32_t)0x00000000) /*!< No advanced feature initialization */ #define UART_ADVFEATURE_TXINVERT_INIT ((uint32_t)0x00000001) /*!< TX pin active level inversion */ #define UART_ADVFEATURE_RXINVERT_INIT ((uint32_t)0x00000002) /*!< RX pin active level inversion */ #define UART_ADVFEATURE_DATAINVERT_INIT ((uint32_t)0x00000004) /*!< Binary data inversion */ #define UART_ADVFEATURE_SWAP_INIT ((uint32_t)0x00000008) /*!< TX/RX pins swap */ #define UART_ADVFEATURE_RXOVERRUNDISABLE_INIT ((uint32_t)0x00000010) /*!< RX overrun disable */ #define UART_ADVFEATURE_DMADISABLEONERROR_INIT ((uint32_t)0x00000020) /*!< DMA disable on Reception Error */ #define UART_ADVFEATURE_AUTOBAUDRATE_INIT ((uint32_t)0x00000040) /*!< Auto Baud rate detection initialization */ #define UART_ADVFEATURE_MSBFIRST_INIT ((uint32_t)0x00000080) /*!< Most significant bit sent/received first */ /** * @} */ /** @defgroup UART_Tx_Inv UART Advanced Feature TX Pin Active Level Inversion * @{ */ #define UART_ADVFEATURE_TXINV_DISABLE ((uint32_t)0x00000000) /*!< TX pin active level inversion disable */ #define UART_ADVFEATURE_TXINV_ENABLE ((uint32_t)USART_CR2_TXINV) /*!< TX pin active level inversion enable */ /** * @} */ /** @defgroup UART_Rx_Inv UART Advanced Feature RX Pin Active Level Inversion * @{ */ #define UART_ADVFEATURE_RXINV_DISABLE ((uint32_t)0x00000000) /*!< RX pin active level inversion disable */ #define UART_ADVFEATURE_RXINV_ENABLE ((uint32_t)USART_CR2_RXINV) /*!< RX pin active level inversion enable */ /** * @} */ /** @defgroup UART_Data_Inv UART Advanced Feature Binary Data Inversion * @{ */ #define UART_ADVFEATURE_DATAINV_DISABLE ((uint32_t)0x00000000) /*!< Binary data inversion disable */ #define UART_ADVFEATURE_DATAINV_ENABLE ((uint32_t)USART_CR2_DATAINV) /*!< Binary data inversion enable */ /** * @} */ /** @defgroup UART_Rx_Tx_Swap UART Advanced Feature RX TX Pins Swap * @{ */ #define UART_ADVFEATURE_SWAP_DISABLE ((uint32_t)0x00000000) /*!< TX/RX pins swap disable */ #define UART_ADVFEATURE_SWAP_ENABLE ((uint32_t)USART_CR2_SWAP) /*!< TX/RX pins swap enable */ /** * @} */ /** @defgroup UART_Overrun_Disable UART Advanced Feature Overrun Disable * @{ */ #define UART_ADVFEATURE_OVERRUN_ENABLE ((uint32_t)0x00000000) /*!< RX overrun enable */ #define UART_ADVFEATURE_OVERRUN_DISABLE ((uint32_t)USART_CR3_OVRDIS) /*!< RX overrun disable */ /** * @} */ /** @defgroup UART_AutoBaudRate_Enable UART Advanced Feature Auto BaudRate Enable * @{ */ #define UART_ADVFEATURE_AUTOBAUDRATE_DISABLE ((uint32_t)0x00000000) /*!< RX Auto Baud rate detection enable */ #define UART_ADVFEATURE_AUTOBAUDRATE_ENABLE ((uint32_t)USART_CR2_ABREN) /*!< RX Auto Baud rate detection disable */ /** * @} */ /** @defgroup UART_DMA_Disable_on_Rx_Error UART Advanced Feature DMA Disable On Rx Error * @{ */ #define UART_ADVFEATURE_DMA_ENABLEONRXERROR ((uint32_t)0x00000000) /*!< DMA enable on Reception Error */ #define UART_ADVFEATURE_DMA_DISABLEONRXERROR ((uint32_t)USART_CR3_DDRE) /*!< DMA disable on Reception Error */ /** * @} */ /** @defgroup UART_MSB_First UART Advanced Feature MSB First * @{ */ #define UART_ADVFEATURE_MSBFIRST_DISABLE ((uint32_t)0x00000000) /*!< Most significant bit sent/received first disable */ #define UART_ADVFEATURE_MSBFIRST_ENABLE ((uint32_t)USART_CR2_MSBFIRST) /*!< Most significant bit sent/received first enable */ /** * @} */ /** @defgroup UART_Stop_Mode_Enable UART Advanced Feature Stop Mode Enable * @{ */ #define UART_ADVFEATURE_STOPMODE_DISABLE ((uint32_t)0x00000000) /*!< UART stop mode disable */ #define UART_ADVFEATURE_STOPMODE_ENABLE ((uint32_t)USART_CR1_UESM) /*!< UART stop mode enable */ /** * @} */ /** @defgroup UART_Mute_Mode UART Advanced Feature Mute Mode Enable * @{ */ #define UART_ADVFEATURE_MUTEMODE_DISABLE ((uint32_t)0x00000000) /*!< UART mute mode disable */ #define UART_ADVFEATURE_MUTEMODE_ENABLE ((uint32_t)USART_CR1_MME) /*!< UART mute mode enable */ /** * @} */ /** @defgroup UART_CR2_ADDRESS_LSB_POS UART Address-matching LSB Position In CR2 Register * @{ */ #define UART_CR2_ADDRESS_LSB_POS ((uint32_t) 24) /** * @} */ /** @defgroup UART_WakeUp_from_Stop_Selection UART WakeUp From Stop Selection * @{ */ #define UART_WAKEUP_ON_ADDRESS ((uint32_t)0x0000) #define UART_WAKEUP_ON_STARTBIT ((uint32_t)USART_CR3_WUS_1) #define UART_WAKEUP_ON_READDATA_NONEMPTY ((uint32_t)USART_CR3_WUS) /** * @} */ /** @defgroup UART_DriverEnable_Polarity UART DriverEnable Polarity * @{ */ #define UART_DE_POLARITY_HIGH ((uint32_t)0x00000000) /*!< Driver enable signal is active high */ #define UART_DE_POLARITY_LOW ((uint32_t)USART_CR3_DEP) /*!< Driver enable signal is active low */ /** * @} */ /** @defgroup UART_CR1_DEAT_ADDRESS_LSB_POS UART Driver Enable Assertion Time LSB Position In CR1 Register * @{ */ #define UART_CR1_DEAT_ADDRESS_LSB_POS ((uint32_t) 21) /*!< UART Driver Enable assertion time LSB position in CR1 register */ /** * @} */ /** @defgroup UART_CR1_DEDT_ADDRESS_LSB_POS UART Driver Enable DeAssertion Time LSB Position In CR1 Register * @{ */ #define UART_CR1_DEDT_ADDRESS_LSB_POS ((uint32_t) 16) /*!< UART Driver Enable de-assertion time LSB position in CR1 register */ /** * @} */ /** @defgroup UART_Interruption_Mask UART Interruptions Flag Mask * @{ */ #define UART_IT_MASK ((uint32_t)0x001F) /*!< UART interruptions flags mask */ /** * @} */ /** @defgroup UART_TimeOut_Value UART polling-based communications time-out value * @{ */ #define HAL_UART_TIMEOUT_VALUE 0x1FFFFFF /*!< UART polling-based communications time-out value */ /** * @} */ /** * @} */ /* Exported macros -----------------------------------------------------------*/ /** @defgroup UART_Exported_Macros UART Exported Macros * @{ */ /** @brief Reset UART handle states. * @param __HANDLE__: UART handle. * @retval None */ #define __HAL_UART_RESET_HANDLE_STATE(__HANDLE__) do{ \ (__HANDLE__)->gState = HAL_UART_STATE_RESET; \ (__HANDLE__)->RxState = HAL_UART_STATE_RESET; \ } while(0) /** @brief Flush the UART Data registers. * @param __HANDLE__: UART handle. * @retval None */ #define __HAL_UART_FLUSH_DRREGISTER(__HANDLE__) \ do{ \ SET_BIT((__HANDLE__)->Instance->RQR, UART_RXDATA_FLUSH_REQUEST); \ SET_BIT((__HANDLE__)->Instance->RQR, UART_TXDATA_FLUSH_REQUEST); \ } while(0) /** @brief Clear the specified UART pending flag. * @param __HANDLE__: specifies the UART Handle. * @param __FLAG__: specifies the flag to check. * This parameter can be any combination of the following values: * @arg UART_CLEAR_PEF, Parity Error Clear Flag * @arg UART_CLEAR_FEF, Framing Error Clear Flag * @arg UART_CLEAR_NEF, Noise detected Clear Flag * @arg UART_CLEAR_OREF, OverRun Error Clear Flag * @arg UART_CLEAR_IDLEF, IDLE line detected Clear Flag * @arg UART_CLEAR_TCF, Transmission Complete Clear Flag * @arg UART_CLEAR_LBDF, LIN Break Detection Clear Flag (not available on all devices) * @arg UART_CLEAR_CTSF, CTS Interrupt Clear Flag * @arg UART_CLEAR_RTOF, Receiver Time Out Clear Flag * @arg UART_CLEAR_EOBF, End Of Block Clear Flag (not available on all devices) * @arg UART_CLEAR_CMF, Character Match Clear Flag * @arg UART_CLEAR_WUF, Wake Up from stop mode Clear Flag (not available on all devices) * @retval None */ #define __HAL_UART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->ICR = (__FLAG__)) /** @brief Clear the UART PE pending flag. * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_CLEAR_PEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_PEF) /** @brief Clear the UART FE pending flag. * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_CLEAR_FEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_FEF) /** @brief Clear the UART NE pending flag. * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_CLEAR_NEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_NEF) /** @brief Clear the UART ORE pending flag. * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_CLEAR_OREFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_OREF) /** @brief Clear the UART IDLE pending flag. * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_IDLEF) /** @brief Check whether the specified UART flag is set or not. * @param __HANDLE__: specifies the UART Handle. * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or * UART peripheral (datasheet: up to five USART/UARTs) * @param __FLAG__: specifies the flag to check. * This parameter can be one of the following values: * @arg UART_FLAG_REACK: Receive enable acknowledge flag * @arg UART_FLAG_TEACK: Transmit enable acknowledge flag * @arg UART_FLAG_WUF: Wake up from stop mode flag * @arg UART_FLAG_RWU: Receiver wake up flag * @arg UART_FLAG_SBKF: Send Break flag * @arg UART_FLAG_CMF: Character match flag * @arg UART_FLAG_BUSY: Busy flag * @arg UART_FLAG_ABRF: Auto Baud rate detection flag * @arg UART_FLAG_ABRE: Auto Baud rate detection error flag * @arg UART_FLAG_EOBF: End of block flag * @arg UART_FLAG_RTOF: Receiver timeout flag * @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5) * @arg UART_FLAG_LBD: LIN Break detection flag * @arg UART_FLAG_TXE: Transmit data register empty flag * @arg UART_FLAG_TC: Transmission Complete flag * @arg UART_FLAG_RXNE: Receive data register not empty flag * @arg UART_FLAG_IDLE: Idle Line detection flag * @arg UART_FLAG_ORE: OverRun Error flag * @arg UART_FLAG_NE: Noise Error flag * @arg UART_FLAG_FE: Framing Error flag * @arg UART_FLAG_PE: Parity Error flag * @retval The new state of __FLAG__ (TRUE or FALSE). */ #define __HAL_UART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->ISR & (__FLAG__)) == (__FLAG__)) /** @brief Enable the specified UART interrupt. * @param __HANDLE__: specifies the UART Handle. * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or * UART peripheral. (datasheet: up to five USART/UARTs) * @param __INTERRUPT__: specifies the UART interrupt source to enable. * This parameter can be one of the following values: * @arg UART_IT_WUF: Wakeup from stop mode interrupt * @arg UART_IT_CM: Character match interrupt * @arg UART_IT_CTS: CTS change interrupt * @arg UART_IT_LBD: LIN Break detection interrupt * @arg UART_IT_TXE: Transmit Data Register empty interrupt * @arg UART_IT_TC: Transmission complete interrupt * @arg UART_IT_RXNE: Receive Data register not empty interrupt * @arg UART_IT_IDLE: Idle line detection interrupt * @arg UART_IT_PE: Parity Error interrupt * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error) * @retval None */ #define __HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 |= (1U << ((__INTERRUPT__) & UART_IT_MASK))): \ ((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 |= (1U << ((__INTERRUPT__) & UART_IT_MASK))): \ ((__HANDLE__)->Instance->CR3 |= (1U << ((__INTERRUPT__) & UART_IT_MASK)))) /** @brief Disable the specified UART interrupt. * @param __HANDLE__: specifies the UART Handle. * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or * UART peripheral. (datasheet: up to five USART/UARTs) * @param __INTERRUPT__: specifies the UART interrupt source to disable. * This parameter can be one of the following values: * @arg UART_IT_WUF: Wakeup from stop mode interrupt * @arg UART_IT_CM: Character match interrupt * @arg UART_IT_CTS: CTS change interrupt * @arg UART_IT_LBD: LIN Break detection interrupt * @arg UART_IT_TXE: Transmit Data Register empty interrupt * @arg UART_IT_TC: Transmission complete interrupt * @arg UART_IT_RXNE: Receive Data register not empty interrupt * @arg UART_IT_IDLE: Idle line detection interrupt * @arg UART_IT_PE: Parity Error interrupt * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error) * @retval None */ #define __HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 &= ~ (1U << ((__INTERRUPT__) & UART_IT_MASK))): \ ((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 &= ~ (1U << ((__INTERRUPT__) & UART_IT_MASK))): \ ((__HANDLE__)->Instance->CR3 &= ~ (1U << ((__INTERRUPT__) & UART_IT_MASK)))) /** @brief Check whether the specified UART interrupt has occurred or not. * @param __HANDLE__: specifies the UART Handle. * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or * UART peripheral. (datasheet: up to five USART/UARTs) * @param __IT__: specifies the UART interrupt to check. * This parameter can be one of the following values: * @arg UART_IT_WUF: Wakeup from stop mode interrupt * @arg UART_IT_CM: Character match interrupt * @arg UART_IT_CTS: CTS change interrupt (not available for UART4 and UART5) * @arg UART_IT_LBD: LIN Break detection interrupt * @arg UART_IT_TXE: Transmit Data Register empty interrupt * @arg UART_IT_TC: Transmission complete interrupt * @arg UART_IT_RXNE: Receive Data register not empty interrupt * @arg UART_IT_IDLE: Idle line detection interrupt * @arg UART_IT_ORE: OverRun Error interrupt * @arg UART_IT_NE: Noise Error interrupt * @arg UART_IT_FE: Framing Error interrupt * @arg UART_IT_PE: Parity Error interrupt * @retval The new state of __IT__ (TRUE or FALSE). */ #define __HAL_UART_GET_IT(__HANDLE__, __IT__) ((__HANDLE__)->Instance->ISR & ((uint32_t)1 << ((__IT__)>> 0x08))) /** @brief Check whether the specified UART interrupt source is enabled or not. * @param __HANDLE__: specifies the UART Handle. * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or * UART peripheral. (datasheet: up to five USART/UARTs) * @param __IT__: specifies the UART interrupt source to check. * This parameter can be one of the following values: * @arg UART_IT_WUF: Wakeup from stop mode interrupt * @arg UART_IT_CM: Character match interrupt * @arg UART_IT_CTS: CTS change interrupt (not available for UART4 and UART5) * @arg UART_IT_LBD: LIN Break detection interrupt * @arg UART_IT_TXE: Transmit Data Register empty interrupt * @arg UART_IT_TC: Transmission complete interrupt * @arg UART_IT_RXNE: Receive Data register not empty interrupt * @arg UART_IT_IDLE: Idle line detection interrupt * @arg UART_IT_ORE: OverRun Error interrupt * @arg UART_IT_NE: Noise Error interrupt * @arg UART_IT_FE: Framing Error interrupt * @arg UART_IT_PE: Parity Error interrupt * @retval The new state of __IT__ (TRUE or FALSE). */ #define __HAL_UART_GET_IT_SOURCE(__HANDLE__, __IT__) ((((((uint8_t)(__IT__)) >> 5U) == 1)? (__HANDLE__)->Instance->CR1:(((((uint8_t)(__IT__)) >> 5U) == 2)? \ (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & ((uint32_t)1 << (((uint16_t)(__IT__)) & UART_IT_MASK))) /** @brief Clear the specified UART ISR flag, in setting the proper ICR register flag. * @param __HANDLE__: specifies the UART Handle. * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or * UART peripheral. (datasheet: up to five USART/UARTs) * @param __IT_CLEAR__: specifies the interrupt clear register flag that needs to be set * to clear the corresponding interrupt * This parameter can be one of the following values: * @arg UART_CLEAR_PEF: Parity Error Clear Flag * @arg UART_CLEAR_FEF: Framing Error Clear Flag * @arg UART_CLEAR_NEF: Noise detected Clear Flag * @arg UART_CLEAR_OREF: OverRun Error Clear Flag * @arg UART_CLEAR_IDLEF: IDLE line detected Clear Flag * @arg UART_CLEAR_TCF: Transmission Complete Clear Flag * @arg UART_CLEAR_LBDF: LIN Break Detection Clear Flag * @arg UART_CLEAR_CTSF: CTS Interrupt Clear Flag * @arg UART_CLEAR_RTOF: Receiver Time Out Clear Flag * @arg UART_CLEAR_EOBF: End Of Block Clear Flag * @arg UART_CLEAR_CMF: Character Match Clear Flag * @arg UART_CLEAR_WUF: Wake Up from stop mode Clear Flag * @retval None */ #define __HAL_UART_CLEAR_IT(__HANDLE__, __IT_CLEAR__) ((__HANDLE__)->Instance->ICR = (uint32_t)(__IT_CLEAR__)) /** @brief Set a specific UART request flag. * @param __HANDLE__: specifies the UART Handle. * This parameter can be UARTx where x: 1, 2, 3, 4, 5 to select the USART or * UART peripheral. (datasheet: up to five USART/UARTs) * @param __REQ__: specifies the request flag to set * This parameter can be one of the following values: * @arg UART_AUTOBAUD_REQUEST: Auto-Baud Rate Request * @arg UART_SENDBREAK_REQUEST: Send Break Request * @arg UART_MUTE_MODE_REQUEST: Mute Mode Request * @arg UART_RXDATA_FLUSH_REQUEST: Receive Data flush Request * @arg UART_TXDATA_FLUSH_REQUEST: Transmit data flush Request * @retval None */ #define __HAL_UART_SEND_REQ(__HANDLE__, __REQ__) ((__HANDLE__)->Instance->RQR |= (uint16_t)(__REQ__)) /** @brief Enable the UART one bit sample method. * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT) /** @brief Disable the UART one bit sample method. * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint32_t)~((uint32_t)USART_CR3_ONEBIT)) /** @brief Enable UART. * @param __HANDLE__: specifies the UART Handle. * The Handle Instance can be UARTx where x: 1, 2, 3, 4 or 5 to select the UART peripheral * @retval None */ #define __HAL_UART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE) /** @brief Disable UART * @param __HANDLE__: specifies the UART Handle. * The Handle Instance can be UARTx where x: 1, 2, 3, 4 or 5 to select the UART peripheral * @retval None */ #define __HAL_UART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE) /** @brief Enable CTS flow control. * @note This macro allows to enable CTS hardware flow control for a given UART instance, * without need to call HAL_UART_Init() function. * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. * @note As macro is expected to be used for modifying CTS Hw flow control feature activation, without need * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : * - UART instance should have already been initialised (through call of HAL_UART_Init() ) * - macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__)) * and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)). * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_HWCONTROL_CTS_ENABLE(__HANDLE__) \ do{ \ SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \ (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_CTSE; \ } while(0) /** @brief Disable CTS flow control. * @note This macro allows to disable CTS hardware flow control for a given UART instance, * without need to call HAL_UART_Init() function. * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. * @note As macro is expected to be used for modifying CTS Hw flow control feature activation, without need * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : * - UART instance should have already been initialised (through call of HAL_UART_Init() ) * - macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__)) * and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)). * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_HWCONTROL_CTS_DISABLE(__HANDLE__) \ do{ \ CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \ (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_CTSE); \ } while(0) /** @brief Enable RTS flow control. * @note This macro allows to enable RTS hardware flow control for a given UART instance, * without need to call HAL_UART_Init() function. * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. * @note As macro is expected to be used for modifying RTS Hw flow control feature activation, without need * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : * - UART instance should have already been initialised (through call of HAL_UART_Init() ) * - macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__)) * and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)). * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_HWCONTROL_RTS_ENABLE(__HANDLE__) \ do{ \ SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE); \ (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_RTSE; \ } while(0) /** @brief Disable RTS flow control. * @note This macro allows to disable RTS hardware flow control for a given UART instance, * without need to call HAL_UART_Init() function. * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. * @note As macro is expected to be used for modifying RTS Hw flow control feature activation, without need * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : * - UART instance should have already been initialised (through call of HAL_UART_Init() ) * - macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__)) * and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)). * @param __HANDLE__: specifies the UART Handle. * @retval None */ #define __HAL_UART_HWCONTROL_RTS_DISABLE(__HANDLE__) \ do{ \ CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE);\ (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_RTSE); \ } while(0) /** * @} */ /* Private macros --------------------------------------------------------*/ /** @defgroup UART_Private_Macros UART Private Macros * @{ */ /** @brief BRR division operation to set BRR register in 8-bit oversampling mode. * @param __PCLK__: UART clock. * @param __BAUD__: Baud rate set by the user. * @retval Division result */ #define UART_DIV_SAMPLING8(__PCLK__, __BAUD__) ((((__PCLK__)*2) + ((__BAUD__)/2)) / (__BAUD__)) /** @brief BRR division operation to set BRR register in 16-bit oversampling mode. * @param __PCLK__: UART clock. * @param __BAUD__: Baud rate set by the user. * @retval Division result */ #define UART_DIV_SAMPLING16(__PCLK__, __BAUD__) (((__PCLK__) + ((__BAUD__)/2)) / (__BAUD__)) /** @brief Check UART Baud rate * @param __BAUDRATE__: Baudrate specified by the user. * The maximum Baud Rate is derived from the maximum clock on F3 (i.e. 72 MHz) * divided by the smallest oversampling used on the USART (i.e. 8) * @retval SET (__BAUDRATE__ is valid) or RESET (__BAUDRATE__ is invalid) */ #define IS_UART_BAUDRATE(__BAUDRATE__) ((__BAUDRATE__) < 9000001) /** @brief Check UART assertion time. * @param __TIME__: 5-bit value assertion time. * @retval Test result (TRUE or FALSE). */ #define IS_UART_ASSERTIONTIME(__TIME__) ((__TIME__) <= 0x1F) /** @brief Check UART deassertion time. * @param __TIME__: 5-bit value deassertion time. * @retval Test result (TRUE or FALSE). */ #define IS_UART_DEASSERTIONTIME(__TIME__) ((__TIME__) <= 0x1F) /** * @brief Ensure that UART frame number of stop bits is valid. * @param __STOPBITS__: UART frame number of stop bits. * @retval SET (__STOPBITS__ is valid) or RESET (__STOPBITS__ is invalid) */ #define IS_UART_STOPBITS(__STOPBITS__) (((__STOPBITS__) == UART_STOPBITS_0_5) || \ ((__STOPBITS__) == UART_STOPBITS_1) || \ ((__STOPBITS__) == UART_STOPBITS_1_5) || \ ((__STOPBITS__) == UART_STOPBITS_2)) /** * @brief Ensure that UART frame parity is valid. * @param __PARITY__: UART frame parity. * @retval SET (__PARITY__ is valid) or RESET (__PARITY__ is invalid) */ #define IS_UART_PARITY(__PARITY__) (((__PARITY__) == UART_PARITY_NONE) || \ ((__PARITY__) == UART_PARITY_EVEN) || \ ((__PARITY__) == UART_PARITY_ODD)) /** * @brief Ensure that UART hardware flow control is valid. * @param __CONTROL__: UART hardware flow control. * @retval SET (__CONTROL__ is valid) or RESET (__CONTROL__ is invalid) */ #define IS_UART_HARDWARE_FLOW_CONTROL(__CONTROL__)\ (((__CONTROL__) == UART_HWCONTROL_NONE) || \ ((__CONTROL__) == UART_HWCONTROL_RTS) || \ ((__CONTROL__) == UART_HWCONTROL_CTS) || \ ((__CONTROL__) == UART_HWCONTROL_RTS_CTS)) /** * @brief Ensure that UART communication mode is valid. * @param __MODE__: UART communication mode. * @retval SET (__MODE__ is valid) or RESET (__MODE__ is invalid) */ #define IS_UART_MODE(__MODE__) ((((__MODE__) & (~((uint32_t)(UART_MODE_TX_RX)))) == (uint32_t)0x00) && ((__MODE__) != (uint32_t)0x00)) /** * @brief Ensure that UART state is valid. * @param __STATE__: UART state. * @retval SET (__STATE__ is valid) or RESET (__STATE__ is invalid) */ #define IS_UART_STATE(__STATE__) (((__STATE__) == UART_STATE_DISABLE) || \ ((__STATE__) == UART_STATE_ENABLE)) /** * @brief Ensure that UART oversampling is valid. * @param __SAMPLING__: UART oversampling. * @retval SET (__SAMPLING__ is valid) or RESET (__SAMPLING__ is invalid) */ #define IS_UART_OVERSAMPLING(__SAMPLING__) (((__SAMPLING__) == UART_OVERSAMPLING_16) || \ ((__SAMPLING__) == UART_OVERSAMPLING_8)) /** * @brief Ensure that UART frame sampling is valid. * @param __ONEBIT__: UART frame sampling. * @retval SET (__ONEBIT__ is valid) or RESET (__ONEBIT__ is invalid) */ #define IS_UART_ONE_BIT_SAMPLE(__ONEBIT__) (((__ONEBIT__) == UART_ONE_BIT_SAMPLE_DISABLE) || \ ((__ONEBIT__) == UART_ONE_BIT_SAMPLE_ENABLE)) /** * @brief Ensure that Address Length detection parameter is valid. * @param __ADDRESS__: UART Adress length value. * @retval SET (__ADDRESS__ is valid) or RESET (__ADDRESS__ is invalid) */ #define IS_UART_ADDRESSLENGTH_DETECT(__ADDRESS__) (((__ADDRESS__) == UART_ADDRESS_DETECT_4B) || \ ((__ADDRESS__) == UART_ADDRESS_DETECT_7B)) /** * @brief Ensure that UART auto Baud rate detection mode is valid. * @param __MODE__: UART auto Baud rate detection mode. * @retval SET (__MODE__ is valid) or RESET (__MODE__ is invalid) */ #define IS_UART_ADVFEATURE_AUTOBAUDRATEMODE(__MODE__) (((__MODE__) == UART_ADVFEATURE_AUTOBAUDRATE_ONSTARTBIT) || \ ((__MODE__) == UART_ADVFEATURE_AUTOBAUDRATE_ONFALLINGEDGE) || \ ((__MODE__) == UART_ADVFEATURE_AUTOBAUDRATE_ON0X7FFRAME) || \ ((__MODE__) == UART_ADVFEATURE_AUTOBAUDRATE_ON0X55FRAME)) /** * @brief Ensure that UART receiver timeout setting is valid. * @param __TIMEOUT__: UART receiver timeout setting. * @retval SET (__TIMEOUT__ is valid) or RESET (__TIMEOUT__ is invalid) */ #define IS_UART_RECEIVER_TIMEOUT(__TIMEOUT__) (((__TIMEOUT__) == UART_RECEIVER_TIMEOUT_DISABLE) || \ ((__TIMEOUT__) == UART_RECEIVER_TIMEOUT_ENABLE)) /** * @brief Ensure that UART LIN state is valid. * @param __LIN__: UART LIN state. * @retval SET (__LIN__ is valid) or RESET (__LIN__ is invalid) */ #define IS_UART_LIN(__LIN__) (((__LIN__) == UART_LIN_DISABLE) || \ ((__LIN__) == UART_LIN_ENABLE)) /** * @brief Ensure that UART LIN break detection length is valid. * @param __LENGTH__: UART LIN break detection length. * @retval SET (__LENGTH__ is valid) or RESET (__LENGTH__ is invalid) */ #define IS_UART_LIN_BREAK_DETECT_LENGTH(__LENGTH__) (((__LENGTH__) == UART_LINBREAKDETECTLENGTH_10B) || \ ((__LENGTH__) == UART_LINBREAKDETECTLENGTH_11B)) /** * @brief Ensure that UART DMA TX state is valid. * @param __DMATX__: UART DMA TX state. * @retval SET (__DMATX__ is valid) or RESET (__DMATX__ is invalid) */ #define IS_UART_DMA_TX(__DMATX__) (((__DMATX__) == UART_DMA_TX_DISABLE) || \ ((__DMATX__) == UART_DMA_TX_ENABLE)) /** * @brief Ensure that UART DMA RX state is valid. * @param __DMARX__: UART DMA RX state. * @retval SET (__DMARX__ is valid) or RESET (__DMARX__ is invalid) */ #define IS_UART_DMA_RX(__DMARX__) (((__DMARX__) == UART_DMA_RX_DISABLE) || \ ((__DMARX__) == UART_DMA_RX_ENABLE)) /** * @brief Ensure that UART half-duplex state is valid. * @param __HDSEL__: UART half-duplex state. * @retval SET (__HDSEL__ is valid) or RESET (__HDSEL__ is invalid) */ #define IS_UART_HALF_DUPLEX(__HDSEL__) (((__HDSEL__) == UART_HALF_DUPLEX_DISABLE) || \ ((__HDSEL__) == UART_HALF_DUPLEX_ENABLE)) /** * @brief Ensure that UART wake-up method is valid. * @param __WAKEUP__: UART wake-up method . * @retval SET (__WAKEUP__ is valid) or RESET (__WAKEUP__ is invalid) */ #define IS_UART_WAKEUPMETHOD(__WAKEUP__) (((__WAKEUP__) == UART_WAKEUPMETHOD_IDLELINE) || \ ((__WAKEUP__) == UART_WAKEUPMETHOD_ADDRESSMARK)) /** * @brief Ensure that UART advanced features initialization is valid. * @param __INIT__: UART advanced features initialization. * @retval SET (__INIT__ is valid) or RESET (__INIT__ is invalid) */ #define IS_UART_ADVFEATURE_INIT(__INIT__) ((__INIT__) <= (UART_ADVFEATURE_NO_INIT | \ UART_ADVFEATURE_TXINVERT_INIT | \ UART_ADVFEATURE_RXINVERT_INIT | \ UART_ADVFEATURE_DATAINVERT_INIT | \ UART_ADVFEATURE_SWAP_INIT | \ UART_ADVFEATURE_RXOVERRUNDISABLE_INIT | \ UART_ADVFEATURE_DMADISABLEONERROR_INIT | \ UART_ADVFEATURE_AUTOBAUDRATE_INIT | \ UART_ADVFEATURE_MSBFIRST_INIT)) /** * @brief Ensure that UART frame TX inversion setting is valid. * @param __TXINV__: UART frame TX inversion setting. * @retval SET (__TXINV__ is valid) or RESET (__TXINV__ is invalid) */ #define IS_UART_ADVFEATURE_TXINV(__TXINV__) (((__TXINV__) == UART_ADVFEATURE_TXINV_DISABLE) || \ ((__TXINV__) == UART_ADVFEATURE_TXINV_ENABLE)) /** * @brief Ensure that UART frame RX inversion setting is valid. * @param __RXINV__: UART frame RX inversion setting. * @retval SET (__RXINV__ is valid) or RESET (__RXINV__ is invalid) */ #define IS_UART_ADVFEATURE_RXINV(__RXINV__) (((__RXINV__) == UART_ADVFEATURE_RXINV_DISABLE) || \ ((__RXINV__) == UART_ADVFEATURE_RXINV_ENABLE)) /** * @brief Ensure that UART frame data inversion setting is valid. * @param __DATAINV__: UART frame data inversion setting. * @retval SET (__DATAINV__ is valid) or RESET (__DATAINV__ is invalid) */ #define IS_UART_ADVFEATURE_DATAINV(__DATAINV__) (((__DATAINV__) == UART_ADVFEATURE_DATAINV_DISABLE) || \ ((__DATAINV__) == UART_ADVFEATURE_DATAINV_ENABLE)) /** * @brief Ensure that UART frame RX/TX pins swap setting is valid. * @param __SWAP__: UART frame RX/TX pins swap setting. * @retval SET (__SWAP__ is valid) or RESET (__SWAP__ is invalid) */ #define IS_UART_ADVFEATURE_SWAP(__SWAP__) (((__SWAP__) == UART_ADVFEATURE_SWAP_DISABLE) || \ ((__SWAP__) == UART_ADVFEATURE_SWAP_ENABLE)) /** * @brief Ensure that UART frame overrun setting is valid. * @param __OVERRUN__: UART frame overrun setting. * @retval SET (__OVERRUN__ is valid) or RESET (__OVERRUN__ is invalid) */ #define IS_UART_OVERRUN(__OVERRUN__) (((__OVERRUN__) == UART_ADVFEATURE_OVERRUN_ENABLE) || \ ((__OVERRUN__) == UART_ADVFEATURE_OVERRUN_DISABLE)) /** * @brief Ensure that UART auto Baud rate state is valid. * @param __AUTOBAUDRATE__: UART auto Baud rate state. * @retval SET (__AUTOBAUDRATE__ is valid) or RESET (__AUTOBAUDRATE__ is invalid) */ #define IS_UART_ADVFEATURE_AUTOBAUDRATE(__AUTOBAUDRATE__) (((__AUTOBAUDRATE__) == UART_ADVFEATURE_AUTOBAUDRATE_DISABLE) || \ ((__AUTOBAUDRATE__) == UART_ADVFEATURE_AUTOBAUDRATE_ENABLE)) /** * @brief Ensure that UART DMA enabling or disabling on error setting is valid. * @param __DMA__: UART DMA enabling or disabling on error setting. * @retval SET (__DMA__ is valid) or RESET (__DMA__ is invalid) */ #define IS_UART_ADVFEATURE_DMAONRXERROR(__DMA__) (((__DMA__) == UART_ADVFEATURE_DMA_ENABLEONRXERROR) || \ ((__DMA__) == UART_ADVFEATURE_DMA_DISABLEONRXERROR)) /** * @brief Ensure that UART frame MSB first setting is valid. * @param __MSBFIRST__: UART frame MSB first setting. * @retval SET (__MSBFIRST__ is valid) or RESET (__MSBFIRST__ is invalid) */ #define IS_UART_ADVFEATURE_MSBFIRST(__MSBFIRST__) (((__MSBFIRST__) == UART_ADVFEATURE_MSBFIRST_DISABLE) || \ ((__MSBFIRST__) == UART_ADVFEATURE_MSBFIRST_ENABLE)) /** * @brief Ensure that UART stop mode state is valid. * @param __STOPMODE__: UART stop mode state. * @retval SET (__STOPMODE__ is valid) or RESET (__STOPMODE__ is invalid) */ #define IS_UART_ADVFEATURE_STOPMODE(__STOPMODE__) (((__STOPMODE__) == UART_ADVFEATURE_STOPMODE_DISABLE) || \ ((__STOPMODE__) == UART_ADVFEATURE_STOPMODE_ENABLE)) /** * @brief Ensure that UART mute mode state is valid. * @param __MUTE__: UART mute mode state. * @retval SET (__MUTE__ is valid) or RESET (__MUTE__ is invalid) */ #define IS_UART_MUTE_MODE(__MUTE__) (((__MUTE__) == UART_ADVFEATURE_MUTEMODE_DISABLE) || \ ((__MUTE__) == UART_ADVFEATURE_MUTEMODE_ENABLE)) /** * @brief Ensure that UART wake-up selection is valid. * @param __WAKE__: UART wake-up selection. * @retval SET (__WAKE__ is valid) or RESET (__WAKE__ is invalid) */ #define IS_UART_WAKEUP_SELECTION(__WAKE__) (((__WAKE__) == UART_WAKEUP_ON_ADDRESS) || \ ((__WAKE__) == UART_WAKEUP_ON_STARTBIT) || \ ((__WAKE__) == UART_WAKEUP_ON_READDATA_NONEMPTY)) /** * @brief Ensure that UART driver enable polarity is valid. * @param __POLARITY__: UART driver enable polarity. * @retval SET (__POLARITY__ is valid) or RESET (__POLARITY__ is invalid) */ #define IS_UART_DE_POLARITY(__POLARITY__) (((__POLARITY__) == UART_DE_POLARITY_HIGH) || \ ((__POLARITY__) == UART_DE_POLARITY_LOW)) /** * @brief Ensure that UART request parameter is valid. * @param __PARAM__: UART request parameter. * @retval SET (__PARAM__ is valid) or RESET (__PARAM__ is invalid) */ #define IS_UART_REQUEST_PARAMETER(__PARAM__) (((__PARAM__) == UART_AUTOBAUD_REQUEST) || \ ((__PARAM__) == UART_SENDBREAK_REQUEST) || \ ((__PARAM__) == UART_MUTE_MODE_REQUEST) || \ ((__PARAM__) == UART_RXDATA_FLUSH_REQUEST) || \ ((__PARAM__) == UART_TXDATA_FLUSH_REQUEST)) /** * @} */ /* Include UART HAL Extension module */ #include "stm32f3xx_hal_uart_ex.h" /* Exported functions --------------------------------------------------------*/ /** @addtogroup UART_Exported_Functions UART Exported Functions * @{ */ /** @addtogroup UART_Exported_Functions_Group1 Initialization and de-initialization functions * @{ */ /* Initialization and de-initialization functions ****************************/ HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart); HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart); HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength); HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod); HAL_StatusTypeDef HAL_UART_DeInit (UART_HandleTypeDef *huart); void HAL_UART_MspInit(UART_HandleTypeDef *huart); void HAL_UART_MspDeInit(UART_HandleTypeDef *huart); /** * @} */ /** @addtogroup UART_Exported_Functions_Group2 IO operation functions * @{ */ /* IO operation functions *****************************************************/ HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout); HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout); HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart); HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart); HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart); void HAL_UART_IRQHandler(UART_HandleTypeDef *huart); void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart); void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart); void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart); void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart); void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart); /** * @} */ /** @addtogroup UART_Exported_Functions_Group3 Peripheral Control functions * @{ */ /* Peripheral Control functions ************************************************/ HAL_StatusTypeDef HAL_MultiProcessor_EnableMuteMode(UART_HandleTypeDef *huart); HAL_StatusTypeDef HAL_MultiProcessor_DisableMuteMode(UART_HandleTypeDef *huart); void HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart); HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart); HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart); HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart); /** * @} */ /** @addtogroup UART_Exported_Functions_Group4 Peripheral State and Error functions * @{ */ /* Peripheral State and Errors functions **************************************************/ HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart); uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart); /** * @} */ /** * @} */ /* Private functions -----------------------------------------------------------*/ /** @addtogroup UART_Private_Functions UART Private Functions * @{ */ HAL_StatusTypeDef UART_SetConfig(UART_HandleTypeDef *huart); void UART_AdvFeatureConfig(UART_HandleTypeDef *huart); HAL_StatusTypeDef UART_CheckIdleState(UART_HandleTypeDef *huart); HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, uint32_t Timeout); HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart); HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart); HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart); void UART_Wakeup_AddressConfig(UART_HandleTypeDef *huart, UART_WakeUpTypeDef WakeUpSelection); /** * @} */ /** * @} */ /** * @} */ #ifdef __cplusplus } #endif #endif /* __STM32F3xx_HAL_UART_H */ /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/