mbed official
The official Mbed 2 C/C++ SDK provides the software platform and libraries to build your applications.
Dependents: hello SerialTestv11 SerialTestv12 Sierpinski ... more
mbed 2
This is the mbed 2 library. If you'd like to learn about Mbed OS please see the mbed-os docs.
TARGET_NUCLEO_H743ZI/TOOLCHAIN_ARM_MICRO/stm32h7xx_ll_sdmmc.h
- Committer:
- AnnaBridge
- Date:
- 2019-02-20
- Revision:
- 172:65be27845400
File content as of revision 172:65be27845400:
/**
******************************************************************************
* @file stm32h7xx_ll_sdmmc.h
* @author MCD Application Team
* @brief Header file of SDMMC HAL module.
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef STM32H7xx_LL_SDMMC_H
#define STM32H7xx_LL_SDMMC_H
#ifdef __cplusplus
extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
#include "stm32h7xx_hal_def.h"
/** @addtogroup STM32H7xx_Driver
* @{
*/
/** @addtogroup SDMMC_LL
* @{
*/
/* Exported types ------------------------------------------------------------*/
/** @defgroup SDMMC_LL_Exported_Types SDMMC_LL Exported Types
* @{
*/
/**
* @brief SDMMC Configuration Structure definition
*/
typedef struct
{
uint32_t ClockEdge; /*!< Specifies the clock transition on which the bit capture is made.
This parameter can be a value of @ref SDMMC_LL_Clock_Edge */
uint32_t ClockPowerSave; /*!< Specifies whether SDMMC Clock output is enabled or
disabled when the bus is idle.
This parameter can be a value of @ref SDMMC_LL_Clock_Power_Save */
uint32_t BusWide; /*!< Specifies the SDMMC bus width.
This parameter can be a value of @ref SDMMC_LL_Bus_Wide */
uint32_t HardwareFlowControl; /*!< Specifies whether the SDMMC hardware flow control is enabled or disabled.
This parameter can be a value of @ref SDMMC_LL_Hardware_Flow_Control */
uint32_t ClockDiv; /*!< Specifies the clock frequency of the SDMMC controller.
This parameter can be a value between Min_Data = 0 and Max_Data = 1023 */
}SDMMC_InitTypeDef;
/**
* @brief SDMMC Command Control structure
*/
typedef struct
{
uint32_t Argument; /*!< Specifies the SDMMC command argument which is sent
to a card as part of a command message. If a command
contains an argument, it must be loaded into this register
before writing the command to the command register. */
uint32_t CmdIndex; /*!< Specifies the SDMMC command index. It must be Min_Data = 0 and
Max_Data = 64 */
uint32_t Response; /*!< Specifies the SDMMC response type.
This parameter can be a value of @ref SDMMC_LL_Response_Type */
uint32_t WaitForInterrupt; /*!< Specifies whether SDMMC wait for interrupt request is
enabled or disabled.
This parameter can be a value of @ref SDMMC_LL_Wait_Interrupt_State */
uint32_t CPSM; /*!< Specifies whether SDMMC Command path state machine (CPSM)
is enabled or disabled.
This parameter can be a value of @ref SDMMC_LL_CPSM_State */
}SDMMC_CmdInitTypeDef;
/**
* @brief SDMMC Data Control structure
*/
typedef struct
{
uint32_t DataTimeOut; /*!< Specifies the data timeout period in card bus clock periods. */
uint32_t DataLength; /*!< Specifies the number of data bytes to be transferred. */
uint32_t DataBlockSize; /*!< Specifies the data block size for block transfer.
This parameter can be a value of @ref SDMMC_LL_Data_Block_Size */
uint32_t TransferDir; /*!< Specifies the data transfer direction, whether the transfer
is a read or write.
This parameter can be a value of @ref SDMMC_LL_Transfer_Direction */
uint32_t TransferMode; /*!< Specifies whether data transfer is in stream or block mode.
This parameter can be a value of @ref SDMMC_LL_Transfer_Type */
uint32_t DPSM; /*!< Specifies whether SDMMC Data path state machine (DPSM)
is enabled or disabled.
This parameter can be a value of @ref SDMMC_LL_DPSM_State */
}SDMMC_DataInitTypeDef;
/**
* @}
*/
/* Exported constants --------------------------------------------------------*/
/** @defgroup SDMMC_LL_Exported_Constants SDMMC_LL Exported Constants
* @{
*/
#define SDMMC_ERROR_NONE ((uint32_t)0x00000000U) /*!< No error */
#define SDMMC_ERROR_CMD_CRC_FAIL ((uint32_t)0x00000001U) /*!< Command response received (but CRC check failed) */
#define SDMMC_ERROR_DATA_CRC_FAIL ((uint32_t)0x00000002U) /*!< Data block sent/received (CRC check failed) */
#define SDMMC_ERROR_CMD_RSP_TIMEOUT ((uint32_t)0x00000004U) /*!< Command response timeout */
#define SDMMC_ERROR_DATA_TIMEOUT ((uint32_t)0x00000008U) /*!< Data timeout */
#define SDMMC_ERROR_TX_UNDERRUN ((uint32_t)0x00000010U) /*!< Transmit FIFO underrun */
#define SDMMC_ERROR_RX_OVERRUN ((uint32_t)0x00000020U) /*!< Receive FIFO overrun */
#define SDMMC_ERROR_ADDR_MISALIGNED ((uint32_t)0x00000040U) /*!< Misaligned address */
#define SDMMC_ERROR_BLOCK_LEN_ERR ((uint32_t)0x00000080U) /*!< Transferred block length is not allowed for the card or the
number of transferred bytes does not match the block length */
#define SDMMC_ERROR_ERASE_SEQ_ERR ((uint32_t)0x00000100U) /*!< An error in the sequence of erase command occurs */
#define SDMMC_ERROR_BAD_ERASE_PARAM ((uint32_t)0x00000200U) /*!< An invalid selection for erase groups */
#define SDMMC_ERROR_WRITE_PROT_VIOLATION ((uint32_t)0x00000400U) /*!< Attempt to program a write protect block */
#define SDMMC_ERROR_LOCK_UNLOCK_FAILED ((uint32_t)0x00000800U) /*!< Sequence or password error has been detected in unlock
command or if there was an attempt to access a locked card */
#define SDMMC_ERROR_COM_CRC_FAILED ((uint32_t)0x00001000U) /*!< CRC check of the previous command failed */
#define SDMMC_ERROR_ILLEGAL_CMD ((uint32_t)0x00002000U) /*!< Command is not legal for the card state */
#define SDMMC_ERROR_CARD_ECC_FAILED ((uint32_t)0x00004000U) /*!< Card internal ECC was applied but failed to correct the data */
#define SDMMC_ERROR_CC_ERR ((uint32_t)0x00008000U) /*!< Internal card controller error */
#define SDMMC_ERROR_GENERAL_UNKNOWN_ERR ((uint32_t)0x00010000U) /*!< General or unknown error */
#define SDMMC_ERROR_STREAM_READ_UNDERRUN ((uint32_t)0x00020000U) /*!< The card could not sustain data reading in stream rmode */
#define SDMMC_ERROR_STREAM_WRITE_OVERRUN ((uint32_t)0x00040000U) /*!< The card could not sustain data programming in stream mode */
#define SDMMC_ERROR_CID_CSD_OVERWRITE ((uint32_t)0x00080000U) /*!< CID/CSD overwrite error */
#define SDMMC_ERROR_WP_ERASE_SKIP ((uint32_t)0x00100000U) /*!< Only partial address space was erased */
#define SDMMC_ERROR_CARD_ECC_DISABLED ((uint32_t)0x00200000U) /*!< Command has been executed without using internal ECC */
#define SDMMC_ERROR_ERASE_RESET ((uint32_t)0x00400000U) /*!< Erase sequence was cleared before executing because an out
of erase sequence command was received */
#define SDMMC_ERROR_AKE_SEQ_ERR ((uint32_t)0x00800000U) /*!< Error in sequence of authentication */
#define SDMMC_ERROR_INVALID_VOLTRANGE ((uint32_t)0x01000000U) /*!< Error in case of invalid voltage range */
#define SDMMC_ERROR_ADDR_OUT_OF_RANGE ((uint32_t)0x02000000U) /*!< Error when addressed block is out of range */
#define SDMMC_ERROR_REQUEST_NOT_APPLICABLE ((uint32_t)0x04000000U) /*!< Error when command request is not applicable */
#define SDMMC_ERROR_INVALID_PARAMETER ((uint32_t)0x08000000U) /*!< the used parameter is not valid */
#define SDMMC_ERROR_UNSUPPORTED_FEATURE ((uint32_t)0x10000000U) /*!< Error when feature is not insupported */
#define SDMMC_ERROR_BUSY ((uint32_t)0x20000000U) /*!< Error when transfer process is busy */
#define SDMMC_ERROR_DMA ((uint32_t)0x40000000U) /*!< Error while DMA transfer */
#define SDMMC_ERROR_TIMEOUT ((uint32_t)0x80000000U) /*!< Timeout error */
/**
* @brief SDMMC Commands Index
*/
#define SDMMC_CMD_GO_IDLE_STATE ((uint8_t)0U) /*!< Resets the SD memory card. */
#define SDMMC_CMD_SEND_OP_COND ((uint8_t)1U) /*!< Sends host capacity support information and activates the card's initialization process. */
#define SDMMC_CMD_ALL_SEND_CID ((uint8_t)2U) /*!< Asks any card connected to the host to send the CID numbers on the CMD line. */
#define SDMMC_CMD_SET_REL_ADDR ((uint8_t)3U) /*!< Asks the card to publish a new relative address (RCA). */
#define SDMMC_CMD_SET_DSR ((uint8_t)4U) /*!< Programs the DSR of all cards. */
#define SDMMC_CMD_SDMMC_SEN_OP_COND ((uint8_t)5U) /*!< Sends host capacity support information (HCS) and asks the accessed card to send its
operating condition register (OCR) content in the response on the CMD line. */
#define SDMMC_CMD_HS_SWITCH ((uint8_t)6U) /*!< Checks switchable function (mode 0) and switch card function (mode 1). */
#define SDMMC_CMD_SEL_DESEL_CARD ((uint8_t)7U) /*!< Selects the card by its own relative address and gets deselected by any other address */
#define SDMMC_CMD_HS_SEND_EXT_CSD ((uint8_t)8U) /*!< Sends SD Memory Card interface condition, which includes host supply voltage information
and asks the card whether card supports voltage. */
#define SDMMC_CMD_SEND_CSD ((uint8_t)9U) /*!< Addressed card sends its card specific data (CSD) on the CMD line. */
#define SDMMC_CMD_SEND_CID ((uint8_t)10U) /*!< Addressed card sends its card identification (CID) on the CMD line. */
#define SDMMC_CMD_VOLTAGE_SWITCH ((uint8_t)11U) /*!< SD card Voltage switch to 1.8V mode. */
#define SDMMC_CMD_STOP_TRANSMISSION ((uint8_t)12U) /*!< Forces the card to stop transmission. */
#define SDMMC_CMD_SEND_STATUS ((uint8_t)13U) /*!< Addressed card sends its status register. */
#define SDMMC_CMD_HS_BUSTEST_READ ((uint8_t)14U) /*!< Reserved */
#define SDMMC_CMD_GO_INACTIVE_STATE ((uint8_t)15U) /*!< Sends an addressed card into the inactive state. */
#define SDMMC_CMD_SET_BLOCKLEN ((uint8_t)16U) /*!< Sets the block length (in bytes for SDSC) for all following block commands
(read, write, lock). Default block length is fixed to 512 Bytes. Not effective
for SDHS and SDXC. */
#define SDMMC_CMD_READ_SINGLE_BLOCK ((uint8_t)17U) /*!< Reads single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of
fixed 512 bytes in case of SDHC and SDXC. */
#define SDMMC_CMD_READ_MULT_BLOCK ((uint8_t)18U) /*!< Continuously transfers data blocks from card to host until interrupted by
STOP_TRANSMISSION command. */
#define SDMMC_CMD_HS_BUSTEST_WRITE ((uint8_t)19U) /*!< 64 bytes tuning pattern is sent for SDR50 and SDR104. */
#define SDMMC_CMD_WRITE_DAT_UNTIL_STOP ((uint8_t)20U) /*!< Speed class control command. */
#define SDMMC_CMD_SET_BLOCK_COUNT ((uint8_t)23U) /*!< Specify block count for CMD18 and CMD25. */
#define SDMMC_CMD_WRITE_SINGLE_BLOCK ((uint8_t)24U) /*!< Writes single block of size selected by SET_BLOCKLEN in case of SDSC, and a block of
fixed 512 bytes in case of SDHC and SDXC. */
#define SDMMC_CMD_WRITE_MULT_BLOCK ((uint8_t)25U) /*!< Continuously writes blocks of data until a STOP_TRANSMISSION follows. */
#define SDMMC_CMD_PROG_CID ((uint8_t)26U) /*!< Reserved for manufacturers. */
#define SDMMC_CMD_PROG_CSD ((uint8_t)27U) /*!< Programming of the programmable bits of the CSD. */
#define SDMMC_CMD_SET_WRITE_PROT ((uint8_t)28U) /*!< Sets the write protection bit of the addressed group. */
#define SDMMC_CMD_CLR_WRITE_PROT ((uint8_t)29U) /*!< Clears the write protection bit of the addressed group. */
#define SDMMC_CMD_SEND_WRITE_PROT ((uint8_t)30U) /*!< Asks the card to send the status of the write protection bits. */
#define SDMMC_CMD_SD_ERASE_GRP_START ((uint8_t)32U) /*!< Sets the address of the first write block to be erased. (For SD card only). */
#define SDMMC_CMD_SD_ERASE_GRP_END ((uint8_t)33U) /*!< Sets the address of the last write block of the continuous range to be erased. */
#define SDMMC_CMD_ERASE_GRP_START ((uint8_t)35U) /*!< Sets the address of the first write block to be erased. Reserved for each command
system set by switch function command (CMD6). */
#define SDMMC_CMD_ERASE_GRP_END ((uint8_t)36U) /*!< Sets the address of the last write block of the continuous range to be erased.
Reserved for each command system set by switch function command (CMD6). */
#define SDMMC_CMD_ERASE ((uint8_t)38U) /*!< Reserved for SD security applications. */
#define SDMMC_CMD_FAST_IO ((uint8_t)39U) /*!< SD card doesn't support it (Reserved). */
#define SDMMC_CMD_GO_IRQ_STATE ((uint8_t)40U) /*!< SD card doesn't support it (Reserved). */
#define SDMMC_CMD_LOCK_UNLOCK ((uint8_t)42U) /*!< Sets/resets the password or lock/unlock the card. The size of the data block is set by
the SET_BLOCK_LEN command. */
#define SDMMC_CMD_APP_CMD ((uint8_t)55U) /*!< Indicates to the card that the next command is an application specific command rather
than a standard command. */
#define SDMMC_CMD_GEN_CMD ((uint8_t)56U) /*!< Used either to transfer a data block to the card or to get a data block from the card
for general purpose/application specific commands. */
#define SDMMC_CMD_NO_CMD ((uint8_t)64U) /*!< No command */
/**
* @brief Following commands are SD Card Specific commands.
* SDMMC_APP_CMD should be sent before sending these commands.
*/
#define SDMMC_CMD_APP_SD_SET_BUSWIDTH ((uint8_t)6U) /*!< (ACMD6) Defines the data bus width to be used for data transfer. The allowed data bus
widths are given in SCR register. */
#define SDMMC_CMD_SD_APP_STATUS ((uint8_t)13U) /*!< (ACMD13) Sends the SD status. */
#define SDMMC_CMD_SD_APP_SEND_NUM_WRITE_BLOCKS ((uint8_t)22U) /*!< (ACMD22) Sends the number of the written (without errors) write blocks. Responds with
32bit+CRC data block. */
#define SDMMC_CMD_SD_APP_OP_COND ((uint8_t)41U) /*!< (ACMD41) Sends host capacity support information (HCS) and asks the accessed card to
send its operating condition register (OCR) content in the response on the CMD line. */
#define SDMMC_CMD_SD_APP_SET_CLR_CARD_DETECT ((uint8_t)42U) /*!< (ACMD42) Connect/Disconnect the 50 KOhm pull-up resistor on CD/DAT3 (pin 1) of the card */
#define SDMMC_CMD_SD_APP_SEND_SCR ((uint8_t)51U) /*!< Reads the SD Configuration Register (SCR). */
#define SDMMC_CMD_SDMMC_RW_DIRECT ((uint8_t)52U) /*!< For SD I/O card only, reserved for security specification. */
#define SDMMC_CMD_SDMMC_RW_EXTENDED ((uint8_t)53U) /*!< For SD I/O card only, reserved for security specification. */
/**
* @brief Following commands are SD Card Specific security commands.
* SDMMC_CMD_APP_CMD should be sent before sending these commands.
*/
#define SDMMC_CMD_SD_APP_GET_MKB ((uint8_t)43U)
#define SDMMC_CMD_SD_APP_GET_MID ((uint8_t)44U)
#define SDMMC_CMD_SD_APP_SET_CER_RN1 ((uint8_t)45U)
#define SDMMC_CMD_SD_APP_GET_CER_RN2 ((uint8_t)46U)
#define SDMMC_CMD_SD_APP_SET_CER_RES2 ((uint8_t)47U)
#define SDMMC_CMD_SD_APP_GET_CER_RES1 ((uint8_t)48U)
#define SDMMC_CMD_SD_APP_SECURE_READ_MULTIPLE_BLOCK ((uint8_t)18U)
#define SDMMC_CMD_SD_APP_SECURE_WRITE_MULTIPLE_BLOCK ((uint8_t)25U)
#define SDMMC_CMD_SD_APP_SECURE_ERASE ((uint8_t)38U)
#define SDMMC_CMD_SD_APP_CHANGE_SECURE_AREA ((uint8_t)49U)
#define SDMMC_CMD_SD_APP_SECURE_WRITE_MKB ((uint8_t)48U)
/**
* @brief Masks for errors Card Status R1 (OCR Register)
*/
#define SDMMC_OCR_ADDR_OUT_OF_RANGE ((uint32_t)0x80000000U)
#define SDMMC_OCR_ADDR_MISALIGNED ((uint32_t)0x40000000U)
#define SDMMC_OCR_BLOCK_LEN_ERR ((uint32_t)0x20000000U)
#define SDMMC_OCR_ERASE_SEQ_ERR ((uint32_t)0x10000000U)
#define SDMMC_OCR_BAD_ERASE_PARAM ((uint32_t)0x08000000U)
#define SDMMC_OCR_WRITE_PROT_VIOLATION ((uint32_t)0x04000000U)
#define SDMMC_OCR_LOCK_UNLOCK_FAILED ((uint32_t)0x01000000U)
#define SDMMC_OCR_COM_CRC_FAILED ((uint32_t)0x00800000U)
#define SDMMC_OCR_ILLEGAL_CMD ((uint32_t)0x00400000U)
#define SDMMC_OCR_CARD_ECC_FAILED ((uint32_t)0x00200000U)
#define SDMMC_OCR_CC_ERROR ((uint32_t)0x00100000U)
#define SDMMC_OCR_GENERAL_UNKNOWN_ERROR ((uint32_t)0x00080000U)
#define SDMMC_OCR_STREAM_READ_UNDERRUN ((uint32_t)0x00040000U)
#define SDMMC_OCR_STREAM_WRITE_OVERRUN ((uint32_t)0x00020000U)
#define SDMMC_OCR_CID_CSD_OVERWRITE ((uint32_t)0x00010000U)
#define SDMMC_OCR_WP_ERASE_SKIP ((uint32_t)0x00008000U)
#define SDMMC_OCR_CARD_ECC_DISABLED ((uint32_t)0x00004000U)
#define SDMMC_OCR_ERASE_RESET ((uint32_t)0x00002000U)
#define SDMMC_OCR_AKE_SEQ_ERROR ((uint32_t)0x00000008U)
#define SDMMC_OCR_ERRORBITS ((uint32_t)0xFDFFE008U)
/**
* @brief Masks for R6 Response
*/
#define SDMMC_R6_GENERAL_UNKNOWN_ERROR ((uint32_t)0x00002000U)
#define SDMMC_R6_ILLEGAL_CMD ((uint32_t)0x00004000U)
#define SDMMC_R6_COM_CRC_FAILED ((uint32_t)0x00008000U)
#define SDMMC_VOLTAGE_WINDOW_SD ((uint32_t)0x80100000U)
#define SDMMC_HIGH_CAPACITY ((uint32_t)0x40000000U)
#define SDMMC_STD_CAPACITY ((uint32_t)0x00000000U)
#define SDMMC_CHECK_PATTERN ((uint32_t)0x000001AAU)
#define SD_SWITCH_1_8V_CAPACITY ((uint32_t)0x01000000U)
#define SDMMC_SDR104_SWITCH_PATTERN ((uint32_t)0x80FF1F03U)
#define SDMMC_SDR50_SWITCH_PATTERN ((uint32_t)0x80FF1F02U)
#define SDMMC_SDR25_SWITCH_PATTERN ((uint32_t)0x80FFFF01U)
#define SDMMC_MAX_VOLT_TRIAL ((uint32_t)0x0000FFFFU)
#define SDMMC_MAX_TRIAL ((uint32_t)0x0000FFFFU)
#define SDMMC_ALLZERO ((uint32_t)0x00000000U)
#define SDMMC_WIDE_BUS_SUPPORT ((uint32_t)0x00040000U)
#define SDMMC_SINGLE_BUS_SUPPORT ((uint32_t)0x00010000U)
#define SDMMC_CARD_LOCKED ((uint32_t)0x02000000U)
#define SDMMC_DATATIMEOUT ((uint32_t)0xFFFFFFFFU)
#define SDMMC_0TO7BITS ((uint32_t)0x000000FFU)
#define SDMMC_8TO15BITS ((uint32_t)0x0000FF00U)
#define SDMMC_16TO23BITS ((uint32_t)0x00FF0000U)
#define SDMMC_24TO31BITS ((uint32_t)0xFF000000U)
#define SDMMC_MAX_DATA_LENGTH ((uint32_t)0x01FFFFFFU)
#define SDMMC_HALFFIFO ((uint32_t)0x00000008U)
#define SDMMC_HALFFIFOBYTES ((uint32_t)0x00000020U)
/**
* @brief Command Class supported
*/
#define SDMMC_CCCC_ERASE ((uint32_t)0x00000020U)
#define SDMMC_CMDTIMEOUT ((uint32_t)5000U) /* Command send and response timeout */
#define SDMMC_MAXERASETIMEOUT ((uint32_t)63000U) /* Max erase Timeout 63 s */
#define SDMMC_STOPTRANSFERTIMEOUT ((uint32_t)100000000U) /* Timeout for STOP TRANSMISSION command */
/** @defgroup SDMMC_LL_Clock_Edge Clock Edge
* @{
*/
#define SDMMC_CLOCK_EDGE_RISING ((uint32_t)0x00000000U)
#define SDMMC_CLOCK_EDGE_FALLING SDMMC_CLKCR_NEGEDGE
#define IS_SDMMC_CLOCK_EDGE(EDGE) (((EDGE) == SDMMC_CLOCK_EDGE_RISING) || \
((EDGE) == SDMMC_CLOCK_EDGE_FALLING))
/**
* @}
*/
/** @defgroup SDMMC_LL_Clock_Power_Save Clock Power Saving
* @{
*/
#define SDMMC_CLOCK_POWER_SAVE_DISABLE ((uint32_t)0x00000000U)
#define SDMMC_CLOCK_POWER_SAVE_ENABLE SDMMC_CLKCR_PWRSAV
#define IS_SDMMC_CLOCK_POWER_SAVE(SAVE) (((SAVE) == SDMMC_CLOCK_POWER_SAVE_DISABLE) || \
((SAVE) == SDMMC_CLOCK_POWER_SAVE_ENABLE))
/**
* @}
*/
/** @defgroup SDMMC_LL_Bus_Wide Bus Width
* @{
*/
#define SDMMC_BUS_WIDE_1B ((uint32_t)0x00000000U)
#define SDMMC_BUS_WIDE_4B SDMMC_CLKCR_WIDBUS_0
#define SDMMC_BUS_WIDE_8B SDMMC_CLKCR_WIDBUS_1
#define IS_SDMMC_BUS_WIDE(WIDE) (((WIDE) == SDMMC_BUS_WIDE_1B) || \
((WIDE) == SDMMC_BUS_WIDE_4B) || \
((WIDE) == SDMMC_BUS_WIDE_8B))
/**
* @}
*/
/** @defgroup SDMMC_LL_Speed_Mode
* @{
*/
#define SDMMC_SPEED_MODE_AUTO ((uint32_t)0x00000000U)
#define SDMMC_SPEED_MODE_DEFAULT ((uint32_t)0x00000001U)
#define SDMMC_SPEED_MODE_HIGH ((uint32_t)0x00000002U)
#define SDMMC_SPEED_MODE_ULTRA ((uint32_t)0x00000003U)
#define IS_SDMMC_SPEED_MODE(MODE) (((MODE) == SDMMC_SPEED_MODE_AUTO) || \
((MODE) == SDMMC_SPEED_MODE_DEFAULT) || \
((MODE) == SDMMC_SPEED_MODE_HIGH) || \
((MODE) == SDMMC_SPEED_MODE_ULTRA))
/**
* @}
*/
/** @defgroup SDMMC_LL_Hardware_Flow_Control Hardware Flow Control
* @{
*/
#define SDMMC_HARDWARE_FLOW_CONTROL_DISABLE ((uint32_t)0x00000000U)
#define SDMMC_HARDWARE_FLOW_CONTROL_ENABLE SDMMC_CLKCR_HWFC_EN
#define IS_SDMMC_HARDWARE_FLOW_CONTROL(CONTROL) (((CONTROL) == SDMMC_HARDWARE_FLOW_CONTROL_DISABLE) || \
((CONTROL) == SDMMC_HARDWARE_FLOW_CONTROL_ENABLE))
/**
* @}
*/
/** @defgroup SDMMC_LL_Clock_Division Clock Division
* @{
*/
/* SDMMC_CK frequency = SDMMCCLK / [2 * CLKDIV] */
#define IS_SDMMC_CLKDIV(DIV) ((DIV) < 0x400U)
/**
* @}
*/
/** @defgroup SDMMC_LL_Command_Index Command Index
* @{
*/
#define IS_SDMMC_CMD_INDEX(INDEX) ((INDEX) < 0x40U)
/**
* @}
*/
/** @defgroup SDMMC_LL_Response_Type Response Type
* @{
*/
#define SDMMC_RESPONSE_NO ((uint32_t)0x00000000U)
#define SDMMC_RESPONSE_SHORT SDMMC_CMD_WAITRESP_0
#define SDMMC_RESPONSE_LONG SDMMC_CMD_WAITRESP
#define IS_SDMMC_RESPONSE(RESPONSE) (((RESPONSE) == SDMMC_RESPONSE_NO) || \
((RESPONSE) == SDMMC_RESPONSE_SHORT) || \
((RESPONSE) == SDMMC_RESPONSE_LONG))
/**
* @}
*/
/** @defgroup SDMMC_LL_Wait_Interrupt_State Wait Interrupt
* @{
*/
#define SDMMC_WAIT_NO ((uint32_t)0x00000000U)
#define SDMMC_WAIT_IT SDMMC_CMD_WAITINT
#define SDMMC_WAIT_PEND SDMMC_CMD_WAITPEND
#define IS_SDMMC_WAIT(WAIT) (((WAIT) == SDMMC_WAIT_NO) || \
((WAIT) == SDMMC_WAIT_IT) || \
((WAIT) == SDMMC_WAIT_PEND))
/**
* @}
*/
/** @defgroup SDMMC_LL_CPSM_State CPSM State
* @{
*/
#define SDMMC_CPSM_DISABLE ((uint32_t)0x00000000U)
#define SDMMC_CPSM_ENABLE SDMMC_CMD_CPSMEN
#define IS_SDMMC_CPSM(CPSM) (((CPSM) == SDMMC_CPSM_DISABLE) || \
((CPSM) == SDMMC_CPSM_ENABLE))
/**
* @}
*/
/** @defgroup SDMMC_LL_Response_Registers Response Register
* @{
*/
#define SDMMC_RESP1 ((uint32_t)0x00000000U)
#define SDMMC_RESP2 ((uint32_t)0x00000004U)
#define SDMMC_RESP3 ((uint32_t)0x00000008U)
#define SDMMC_RESP4 ((uint32_t)0x0000000CU)
#define IS_SDMMC_RESP(RESP) (((RESP) == SDMMC_RESP1) || \
((RESP) == SDMMC_RESP2) || \
((RESP) == SDMMC_RESP3) || \
((RESP) == SDMMC_RESP4))
/** @defgroup SDMMC_Internal_DMA_Mode SDMMC Internal DMA Mode
* @{
*/
#define SDMMC_DISABLE_IDMA ((uint32_t)0x00000000)
#define SDMMC_ENABLE_IDMA_SINGLE_BUFF (SDMMC_IDMA_IDMAEN)
#define SDMMC_ENABLE_IDMA_DOUBLE_BUFF0 (SDMMC_IDMA_IDMAEN | SDMMC_IDMA_IDMABMODE)
#define SDMMC_ENABLE_IDMA_DOUBLE_BUFF1 (SDMMC_IDMA_IDMAEN | SDMMC_IDMA_IDMABMODE | SDMMC_IDMA_IDMABACT)
/**
* @}
*/
/** @defgroup SDMMC_LL_Data_Length Data Lenght
* @{
*/
#define IS_SDMMC_DATA_LENGTH(LENGTH) ((LENGTH) <= 0x01FFFFFFU)
/**
* @}
*/
/** @defgroup SDMMC_LL_Data_Block_Size Data Block Size
* @{
*/
#define SDMMC_DATABLOCK_SIZE_1B ((uint32_t)0x00000000U)
#define SDMMC_DATABLOCK_SIZE_2B SDMMC_DCTRL_DBLOCKSIZE_0
#define SDMMC_DATABLOCK_SIZE_4B SDMMC_DCTRL_DBLOCKSIZE_1
#define SDMMC_DATABLOCK_SIZE_8B (SDMMC_DCTRL_DBLOCKSIZE_0|SDMMC_DCTRL_DBLOCKSIZE_1)
#define SDMMC_DATABLOCK_SIZE_16B SDMMC_DCTRL_DBLOCKSIZE_2
#define SDMMC_DATABLOCK_SIZE_32B (SDMMC_DCTRL_DBLOCKSIZE_0|SDMMC_DCTRL_DBLOCKSIZE_2)
#define SDMMC_DATABLOCK_SIZE_64B (SDMMC_DCTRL_DBLOCKSIZE_1|SDMMC_DCTRL_DBLOCKSIZE_2)
#define SDMMC_DATABLOCK_SIZE_128B (SDMMC_DCTRL_DBLOCKSIZE_0|SDMMC_DCTRL_DBLOCKSIZE_1|SDMMC_DCTRL_DBLOCKSIZE_2)
#define SDMMC_DATABLOCK_SIZE_256B SDMMC_DCTRL_DBLOCKSIZE_3
#define SDMMC_DATABLOCK_SIZE_512B (SDMMC_DCTRL_DBLOCKSIZE_0|SDMMC_DCTRL_DBLOCKSIZE_3)
#define SDMMC_DATABLOCK_SIZE_1024B (SDMMC_DCTRL_DBLOCKSIZE_1|SDMMC_DCTRL_DBLOCKSIZE_3)
#define SDMMC_DATABLOCK_SIZE_2048B (SDMMC_DCTRL_DBLOCKSIZE_0|SDMMC_DCTRL_DBLOCKSIZE_1|SDMMC_DCTRL_DBLOCKSIZE_3)
#define SDMMC_DATABLOCK_SIZE_4096B (SDMMC_DCTRL_DBLOCKSIZE_2|SDMMC_DCTRL_DBLOCKSIZE_3)
#define SDMMC_DATABLOCK_SIZE_8192B (SDMMC_DCTRL_DBLOCKSIZE_0|SDMMC_DCTRL_DBLOCKSIZE_2|SDMMC_DCTRL_DBLOCKSIZE_3)
#define SDMMC_DATABLOCK_SIZE_16384B (SDMMC_DCTRL_DBLOCKSIZE_1|SDMMC_DCTRL_DBLOCKSIZE_2|SDMMC_DCTRL_DBLOCKSIZE_3)
#define IS_SDMMC_BLOCK_SIZE(SIZE) (((SIZE) == SDMMC_DATABLOCK_SIZE_1B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_2B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_4B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_8B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_16B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_32B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_64B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_128B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_256B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_512B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_1024B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_2048B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_4096B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_8192B) || \
((SIZE) == SDMMC_DATABLOCK_SIZE_16384B))
/**
* @}
*/
/** @defgroup SDMMC_LL_Transfer_Direction Transfer Direction
* @{
*/
#define SDMMC_TRANSFER_DIR_TO_CARD ((uint32_t)0x00000000U)
#define SDMMC_TRANSFER_DIR_TO_SDMMC SDMMC_DCTRL_DTDIR
#define IS_SDMMC_TRANSFER_DIR(DIR) (((DIR) == SDMMC_TRANSFER_DIR_TO_CARD) || \
((DIR) == SDMMC_TRANSFER_DIR_TO_SDMMC))
/**
* @}
*/
/** @defgroup SDMMC_LL_Transfer_Type Transfer Type
* @{
*/
#define SDMMC_TRANSFER_MODE_BLOCK ((uint32_t)0x00000000U)
#define SDMMC_TRANSFER_MODE_STREAM SDMMC_DCTRL_DTMODE_1
#define IS_SDMMC_TRANSFER_MODE(MODE) (((MODE) == SDMMC_TRANSFER_MODE_BLOCK) || \
((MODE) == SDMMC_TRANSFER_MODE_STREAM))
/**
* @}
*/
/** @defgroup SDMMC_LL_DPSM_State DPSM State
* @{
*/
#define SDMMC_DPSM_DISABLE ((uint32_t)0x00000000U)
#define SDMMC_DPSM_ENABLE SDMMC_DCTRL_DTEN
#define IS_SDMMC_DPSM(DPSM) (((DPSM) == SDMMC_DPSM_DISABLE) ||\
((DPSM) == SDMMC_DPSM_ENABLE))
/**
* @}
*/
/** @defgroup SDMMC_LL_Read_Wait_Mode Read Wait Mode
* @{
*/
#define SDMMC_READ_WAIT_MODE_DATA2 ((uint32_t)0x00000000U)
#define SDMMC_READ_WAIT_MODE_CLK (SDMMC_DCTRL_RWMOD)
#define IS_SDMMC_READWAIT_MODE(MODE) (((MODE) == SDMMC_READ_WAIT_MODE_CLK) || \
((MODE) == SDMMC_READ_WAIT_MODE_DATA2))
/**
* @}
*/
/** @defgroup SDMMC_LL_Interrupt_sources Interrupt Sources
* @{
*/
#define SDMMC_IT_CCRCFAIL SDMMC_MASK_CCRCFAILIE
#define SDMMC_IT_DCRCFAIL SDMMC_MASK_DCRCFAILIE
#define SDMMC_IT_CTIMEOUT SDMMC_MASK_CTIMEOUTIE
#define SDMMC_IT_DTIMEOUT SDMMC_MASK_DTIMEOUTIE
#define SDMMC_IT_TXUNDERR SDMMC_MASK_TXUNDERRIE
#define SDMMC_IT_RXOVERR SDMMC_MASK_RXOVERRIE
#define SDMMC_IT_CMDREND SDMMC_MASK_CMDRENDIE
#define SDMMC_IT_CMDSENT SDMMC_MASK_CMDSENTIE
#define SDMMC_IT_DATAEND SDMMC_MASK_DATAENDIE
#define SDMMC_IT_DHOLD SDMMC_MASK_DHOLDIE
#define SDMMC_IT_DBCKEND SDMMC_MASK_DBCKENDIE
#define SDMMC_IT_DABORT SDMMC_MASK_DABORTIE
#define SDMMC_IT_TXFIFOHE SDMMC_MASK_TXFIFOHEIE
#define SDMMC_IT_RXFIFOHF SDMMC_MASK_RXFIFOHFIE
#define SDMMC_IT_RXFIFOF SDMMC_MASK_RXFIFOFIE
#define SDMMC_IT_TXFIFOE SDMMC_MASK_TXFIFOEIE
#define SDMMC_IT_BUSYD0END SDMMC_MASK_BUSYD0ENDIE
#define SDMMC_IT_SDIOIT SDMMC_MASK_SDIOITIE
#define SDMMC_IT_ACKFAIL SDMMC_MASK_ACKFAILIE
#define SDMMC_IT_ACKTIMEOUT SDMMC_MASK_ACKTIMEOUTIE
#define SDMMC_IT_VSWEND SDMMC_MASK_VSWENDIE
#define SDMMC_IT_CKSTOP SDMMC_MASK_CKSTOPIE
#define SDMMC_IT_IDMABTC SDMMC_MASK_IDMABTCIE
/**
* @}
*/
/** @defgroup SDMMC_LL_Flags Flags
* @{
*/
#define SDMMC_FLAG_CCRCFAIL SDMMC_STA_CCRCFAIL
#define SDMMC_FLAG_DCRCFAIL SDMMC_STA_DCRCFAIL
#define SDMMC_FLAG_CTIMEOUT SDMMC_STA_CTIMEOUT
#define SDMMC_FLAG_DTIMEOUT SDMMC_STA_DTIMEOUT
#define SDMMC_FLAG_TXUNDERR SDMMC_STA_TXUNDERR
#define SDMMC_FLAG_RXOVERR SDMMC_STA_RXOVERR
#define SDMMC_FLAG_CMDREND SDMMC_STA_CMDREND
#define SDMMC_FLAG_CMDSENT SDMMC_STA_CMDSENT
#define SDMMC_FLAG_DATAEND SDMMC_STA_DATAEND
#define SDMMC_FLAG_DHOLD SDMMC_STA_DHOLD
#define SDMMC_FLAG_DBCKEND SDMMC_STA_DBCKEND
#define SDMMC_FLAG_DABORT SDMMC_STA_DABORT
#define SDMMC_FLAG_DPSMACT SDMMC_STA_DPSMACT
#define SDMMC_FLAG_CMDACT SDMMC_STA_CPSMACT
#define SDMMC_FLAG_TXFIFOHE SDMMC_STA_TXFIFOHE
#define SDMMC_FLAG_RXFIFOHF SDMMC_STA_RXFIFOHF
#define SDMMC_FLAG_TXFIFOF SDMMC_STA_TXFIFOF
#define SDMMC_FLAG_RXFIFOF SDMMC_STA_RXFIFOF
#define SDMMC_FLAG_TXFIFOE SDMMC_STA_TXFIFOE
#define SDMMC_FLAG_RXFIFOE SDMMC_STA_RXFIFOE
#define SDMMC_FLAG_BUSYD0 SDMMC_STA_BUSYD0
#define SDMMC_FLAG_BUSYD0END SDMMC_STA_BUSYD0END
#define SDMMC_FLAG_SDIOIT SDMMC_STA_SDIOIT
#define SDMMC_FLAG_ACKFAIL SDMMC_STA_ACKFAIL
#define SDMMC_FLAG_ACKTIMEOUT SDMMC_STA_ACKTIMEOUT
#define SDMMC_FLAG_VSWEND SDMMC_STA_VSWEND
#define SDMMC_FLAG_CKSTOP SDMMC_STA_CKSTOP
#define SDMMC_FLAG_IDMATE SDMMC_STA_IDMATE
#define SDMMC_FLAG_IDMABTC SDMMC_STA_IDMABTC
#define SDMMC_STATIC_FLAGS ((uint32_t)(SDMMC_FLAG_CCRCFAIL | SDMMC_FLAG_DCRCFAIL | SDMMC_FLAG_CTIMEOUT |\
SDMMC_FLAG_DTIMEOUT | SDMMC_FLAG_TXUNDERR | SDMMC_FLAG_RXOVERR |\
SDMMC_FLAG_CMDREND | SDMMC_FLAG_CMDSENT | SDMMC_FLAG_DATAEND |\
SDMMC_FLAG_DHOLD | SDMMC_FLAG_DBCKEND | SDMMC_FLAG_DABORT |\
SDMMC_FLAG_BUSYD0END | SDMMC_FLAG_SDIOIT | SDMMC_FLAG_ACKFAIL |\
SDMMC_FLAG_ACKTIMEOUT | SDMMC_FLAG_VSWEND | SDMMC_FLAG_CKSTOP |\
SDMMC_FLAG_IDMATE | SDMMC_FLAG_IDMABTC))
#define SDMMC_STATIC_CMD_FLAGS ((uint32_t)(SDMMC_FLAG_CCRCFAIL | SDMMC_FLAG_CTIMEOUT | SDMMC_FLAG_CMDREND |\
SDMMC_FLAG_CMDSENT | SDMMC_FLAG_BUSYD0END))
#define SDMMC_STATIC_DATA_FLAGS ((uint32_t)(SDMMC_FLAG_DCRCFAIL | SDMMC_FLAG_DTIMEOUT | SDMMC_FLAG_TXUNDERR |\
SDMMC_FLAG_RXOVERR | SDMMC_FLAG_DATAEND | SDMMC_FLAG_DHOLD |\
SDMMC_FLAG_DBCKEND | SDMMC_FLAG_DABORT | SDMMC_FLAG_IDMATE |\
SDMMC_FLAG_IDMABTC))
/**
* @}
*/
/**
* @}
*/
/* Exported macro ------------------------------------------------------------*/
/** @defgroup SDMMC_LL_Exported_macros SDMMC_LL Exported Macros
* @{
*/
/** @defgroup SDMMC_LL_Register Bits And Addresses Definitions
* @brief SDMMC_LL registers bit address in the alias region
* @{
*/
/* ---------------------- SDMMC registers bit mask --------------------------- */
/* --- CLKCR Register ---*/
/* CLKCR register clear mask */
#define CLKCR_CLEAR_MASK ((uint32_t)(SDMMC_CLKCR_CLKDIV | SDMMC_CLKCR_PWRSAV |\
SDMMC_CLKCR_WIDBUS |\
SDMMC_CLKCR_NEGEDGE | SDMMC_CLKCR_HWFC_EN |\
SDMMC_CLKCR_DDR | SDMMC_CLKCR_BUSSPEED |\
SDMMC_CLKCR_SELCLKRX))
/* --- DCTRL Register ---*/
/* SDMMC DCTRL Clear Mask */
#define DCTRL_CLEAR_MASK ((uint32_t)(SDMMC_DCTRL_DTEN | SDMMC_DCTRL_DTDIR |\
SDMMC_DCTRL_DTMODE | SDMMC_DCTRL_DBLOCKSIZE))
/* --- CMD Register ---*/
/* CMD Register clear mask */
#define CMD_CLEAR_MASK ((uint32_t)(SDMMC_CMD_CMDINDEX | SDMMC_CMD_WAITRESP |\
SDMMC_CMD_WAITINT | SDMMC_CMD_WAITPEND |\
SDMMC_CMD_CPSMEN | SDMMC_CMD_CMDSUSPEND))
/* SDMMC Initialization Frequency (400KHz max) for Peripheral CLK 200MHz*/
#define SDMMC_INIT_CLK_DIV ((uint8_t)0xFA)
/* SDMMC Default Speed Frequency (25Mhz max) for Peripheral CLK 200MHz*/
#define SDMMC_NSpeed_CLK_DIV ((uint8_t)0x4)
/* SDMMC High Speed Frequency (50Mhz max) for Peripheral CLK 200MHz*/
#define SDMMC_HSpeed_CLK_DIV ((uint8_t)0x2)
/**
* @}
*/
/** @defgroup SDMMC_LL_Interrupt_Clock Interrupt And Clock Configuration
* @brief macros to handle interrupts and specific clock configurations
* @{
*/
/**
* @brief Enable the SDMMC device interrupt.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @param __INTERRUPT__ : specifies the SDMMC interrupt sources to be enabled.
* This parameter can be one or a combination of the following values:
* @arg SDMMC_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
* @arg SDMMC_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
* @arg SDMMC_IT_CTIMEOUT: Command response timeout interrupt
* @arg SDMMC_IT_DTIMEOUT: Data timeout interrupt
* @arg SDMMC_IT_TXUNDERR: Transmit FIFO underrun error interrupt
* @arg SDMMC_IT_RXOVERR: Received FIFO overrun error interrupt
* @arg SDMMC_IT_CMDREND: Command response received (CRC check passed) interrupt
* @arg SDMMC_IT_CMDSENT: Command sent (no response required) interrupt
* @arg SDMMC_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt
* @arg SDMMC_IT_DHOLD: Data transfer Hold interrupt
* @arg SDMMC_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt
* @arg SDMMC_IT_DABORT: Data transfer aborted by CMD12 interrupt
* @arg SDMMC_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
* @arg SDMMC_IT_RXFIFOHF: Receive FIFO Half Full interrupt
* @arg SDMMC_IT_RXFIFOF: Receive FIFO full interrupt
* @arg SDMMC_IT_TXFIFOE: Transmit FIFO empty interrupt
* @arg SDMMC_IT_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected interrupt
* @arg SDMMC_IT_SDIOIT: SDIO interrupt received interrupt
* @arg SDMMC_IT_ACKFAIL: Boot Acknowledgment received interrupt
* @arg SDMMC_IT_ACKTIMEOUT: Boot Acknowledgment timeout interrupt
* @arg SDMMC_IT_VSWEND: Voltage switch critical timing section completion interrupt
* @arg SDMMC_IT_CKSTOP: SDMMC_CK stopped in Voltage switch procedure interrupt
* @arg SDMMC_IT_IDMABTC: IDMA buffer transfer complete interrupt
* @retval None
*/
#define __SDMMC_ENABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->MASK |= (__INTERRUPT__))
/**
* @brief Disable the SDMMC device interrupt.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @param __INTERRUPT__ : specifies the SDMMC interrupt sources to be disabled.
* This parameter can be one or a combination of the following values:
* @arg SDMMC_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
* @arg SDMMC_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
* @arg SDMMC_IT_CTIMEOUT: Command response timeout interrupt
* @arg SDMMC_IT_DTIMEOUT: Data timeout interrupt
* @arg SDMMC_IT_TXUNDERR: Transmit FIFO underrun error interrupt
* @arg SDMMC_IT_RXOVERR: Received FIFO overrun error interrupt
* @arg SDMMC_IT_CMDREND: Command response received (CRC check passed) interrupt
* @arg SDMMC_IT_CMDSENT: Command sent (no response required) interrupt
* @arg SDMMC_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt
* @arg SDMMC_IT_DHOLD: Data transfer Hold interrupt
* @arg SDMMC_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt
* @arg SDMMC_IT_DABORT: Data transfer aborted by CMD12 interrupt
* @arg SDMMC_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
* @arg SDMMC_IT_RXFIFOHF: Receive FIFO Half Full interrupt
* @arg SDMMC_IT_RXFIFOF: Receive FIFO full interrupt
* @arg SDMMC_IT_TXFIFOE: Transmit FIFO empty interrupt
* @arg SDMMC_IT_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected interrupt
* @arg SDMMC_IT_SDIOIT: SDIO interrupt received interrupt
* @arg SDMMC_IT_ACKFAIL: Boot Acknowledgment received interrupt
* @arg SDMMC_IT_ACKTIMEOUT: Boot Acknowledgment timeout interrupt
* @arg SDMMC_IT_VSWEND: Voltage switch critical timing section completion interrupt
* @arg SDMMC_IT_CKSTOP: SDMMC_CK stopped in Voltage switch procedure interrupt
* @arg SDMMC_IT_IDMABTC: IDMA buffer transfer complete interrupt
* @retval None
*/
#define __SDMMC_DISABLE_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->MASK &= ~(__INTERRUPT__))
/**
* @brief Checks whether the specified SDMMC flag is set or not.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @param __FLAG__: specifies the flag to check.
* This parameter can be one of the following values:
* @arg SDMMC_FLAG_CCRCFAIL: Command response received (CRC check failed)
* @arg SDMMC_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
* @arg SDMMC_FLAG_CTIMEOUT: Command response timeout
* @arg SDMMC_FLAG_DTIMEOUT: Data timeout
* @arg SDMMC_FLAG_TXUNDERR: Transmit FIFO underrun error
* @arg SDMMC_FLAG_RXOVERR: Received FIFO overrun error
* @arg SDMMC_FLAG_CMDREND: Command response received (CRC check passed)
* @arg SDMMC_FLAG_CMDSENT: Command sent (no response required)
* @arg SDMMC_FLAG_DATAEND: Data end (data counter, DATACOUNT, is zero)
* @arg SDMMC_FLAG_DHOLD: Data transfer Hold
* @arg SDMMC_FLAG_DBCKEND: Data block sent/received (CRC check passed)
* @arg SDMMC_FLAG_DABORT: Data transfer aborted by CMD12
* @arg SDMMC_FLAG_CPSMACT: Command path state machine active
* @arg SDMMC_FLAG_DPSMACT: Data path state machine active
* @arg SDMMC_FLAG_TXFIFOHE: Transmit FIFO Half Empty
* @arg SDMMC_FLAG_RXFIFOHF: Receive FIFO Half Full
* @arg SDMMC_FLAG_TXFIFOF: Transmit FIFO full
* @arg SDMMC_FLAG_RXFIFOF: Receive FIFO full
* @arg SDMMC_FLAG_TXFIFOE: Transmit FIFO empty
* @arg SDMMC_FLAG_RXFIFOE: Receive FIFO empty
* @arg SDMMC_FLAG_BUSYD0: Inverted value of SDMMC_D0 line (Busy)
* @arg SDMMC_FLAG_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected
* @arg SDMMC_FLAG_SDIOIT: SDIO interrupt received
* @arg SDMMC_FLAG_ACKFAIL: Boot Acknowledgment received
* @arg SDMMC_FLAG_ACKTIMEOUT: Boot Acknowledgment timeout
* @arg SDMMC_FLAG_VSWEND: Voltage switch critical timing section completion
* @arg SDMMC_FLAG_CKSTOP: SDMMC_CK stopped in Voltage switch procedure
* @arg SDMMC_FLAG_IDMATE: IDMA transfer error
* @arg SDMMC_FLAG_IDMABTC: IDMA buffer transfer complete
* @retval The new state of SDMMC_FLAG (SET or RESET).
*/
#define __SDMMC_GET_FLAG(__INSTANCE__, __FLAG__) (((__INSTANCE__)->STA &(__FLAG__)) != 0U)
/**
* @brief Clears the SDMMC pending flags.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @param __FLAG__: specifies the flag to clear.
* This parameter can be one or a combination of the following values:
* @arg SDMMC_FLAG_CCRCFAIL: Command response received (CRC check failed)
* @arg SDMMC_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
* @arg SDMMC_FLAG_CTIMEOUT: Command response timeout
* @arg SDMMC_FLAG_DTIMEOUT: Data timeout
* @arg SDMMC_FLAG_TXUNDERR: Transmit FIFO underrun error
* @arg SDMMC_FLAG_RXOVERR: Received FIFO overrun error
* @arg SDMMC_FLAG_CMDREND: Command response received (CRC check passed)
* @arg SDMMC_FLAG_CMDSENT: Command sent (no response required)
* @arg SDMMC_FLAG_DATAEND: Data end (data counter, DATACOUNT, is zero)
* @arg SDMMC_FLAG_DHOLD: Data transfer Hold
* @arg SDMMC_FLAG_DBCKEND: Data block sent/received (CRC check passed)
* @arg SDMMC_FLAG_DABORT: Data transfer aborted by CMD12
* @arg SDMMC_FLAG_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected
* @arg SDMMC_FLAG_SDIOIT: SDIO interrupt received
* @arg SDMMC_FLAG_ACKFAIL: Boot Acknowledgment received
* @arg SDMMC_FLAG_ACKTIMEOUT: Boot Acknowledgment timeout
* @arg SDMMC_FLAG_VSWEND: Voltage switch critical timing section completion
* @arg SDMMC_FLAG_CKSTOP: SDMMC_CK stopped in Voltage switch procedure
* @arg SDMMC_FLAG_IDMATE: IDMA transfer error
* @arg SDMMC_FLAG_IDMABTC: IDMA buffer transfer complete
* @retval None
*/
#define __SDMMC_CLEAR_FLAG(__INSTANCE__, __FLAG__) ((__INSTANCE__)->ICR = (__FLAG__))
/**
* @brief Checks whether the specified SDMMC interrupt has occurred or not.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @param __INTERRUPT__: specifies the SDMMC interrupt source to check.
* This parameter can be one of the following values:
* @arg SDMMC_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
* @arg SDMMC_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
* @arg SDMMC_IT_CTIMEOUT: Command response timeout interrupt
* @arg SDMMC_IT_DTIMEOUT: Data timeout interrupt
* @arg SDMMC_IT_TXUNDERR: Transmit FIFO underrun error interrupt
* @arg SDMMC_IT_RXOVERR: Received FIFO overrun error interrupt
* @arg SDMMC_IT_CMDREND: Command response received (CRC check passed) interrupt
* @arg SDMMC_IT_CMDSENT: Command sent (no response required) interrupt
* @arg SDMMC_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt
* @arg SDMMC_IT_DHOLD: Data transfer Hold interrupt
* @arg SDMMC_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt
* @arg SDMMC_IT_DABORT: Data transfer aborted by CMD12 interrupt
* @arg SDMMC_IT_DPSMACT: Data path state machine active interrupt
* @arg SDMMC_IT_CPSMACT: Command path state machine active interrupt
* @arg SDMMC_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
* @arg SDMMC_IT_RXFIFOHF: Receive FIFO Half Full interrupt
* @arg SDMMC_IT_TXFIFOF: Transmit FIFO full interrupt
* @arg SDMMC_IT_RXFIFOF: Receive FIFO full interrupt
* @arg SDMMC_IT_TXFIFOE: Transmit FIFO empty interrupt
* @arg SDMMC_IT_RXFIFOE: Receive FIFO empty interrupt
* @arg SDMMC_IT_BUSYD0: Inverted value of SDMMC_D0 line (Busy)
* @arg SDMMC_IT_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected interrupt
* @arg SDMMC_IT_SDIOIT: SDIO interrupt received interrupt
* @arg SDMMC_IT_ACKFAIL: Boot Acknowledgment received interrupt
* @arg SDMMC_IT_ACKTIMEOUT: Boot Acknowledgment timeout interrupt
* @arg SDMMC_IT_VSWEND: Voltage switch critical timing section completion interrupt
* @arg SDMMC_IT_CKSTOP: SDMMC_CK stopped in Voltage switch procedure interrupt
* @arg SDMMC_IT_IDMATE: IDMA transfer error interrupt
* @arg SDMMC_IT_IDMABTC: IDMA buffer transfer complete interrupt
* @retval The new state of SDMMC_IT (SET or RESET).
*/
#define __SDMMC_GET_IT (__INSTANCE__, __INTERRUPT__) (((__INSTANCE__)->STA &(__INTERRUPT__)) == (__INTERRUPT__))
/**
* @brief Clears the SDMMC's interrupt pending bits.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @param __INTERRUPT__: specifies the interrupt pending bit to clear.
* This parameter can be one or a combination of the following values:
* @arg SDMMC_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
* @arg SDMMC_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
* @arg SDMMC_IT_CTIMEOUT: Command response timeout interrupt
* @arg SDMMC_IT_DTIMEOUT: Data timeout interrupt
* @arg SDMMC_IT_TXUNDERR: Transmit FIFO underrun error interrupt
* @arg SDMMC_IT_RXOVERR: Received FIFO overrun error interrupt
* @arg SDMMC_IT_CMDREND: Command response received (CRC check passed) interrupt
* @arg SDMMC_IT_CMDSENT: Command sent (no response required) interrupt
* @arg SDMMC_IT_DATAEND: Data end (data counter, DATACOUNT, is zero) interrupt
* @arg SDMMC_IT_DHOLD: Data transfer Hold interrupt
* @arg SDMMC_IT_DBCKEND: Data block sent/received (CRC check passed) interrupt
* @arg SDMMC_IT_DABORT: Data transfer aborted by CMD12 interrupt
* @arg SDMMC_IT_BUSYD0END: End of SDMMC_D0 Busy following a CMD response detected interrupt
* @arg SDMMC_IT_SDIOIT: SDIO interrupt received interrupt
* @arg SDMMC_IT_ACKFAIL: Boot Acknowledgment received interrupt
* @arg SDMMC_IT_ACKTIMEOUT: Boot Acknowledgment timeout interrupt
* @arg SDMMC_IT_VSWEND: Voltage switch critical timing section completion interrupt
* @arg SDMMC_IT_CKSTOP: SDMMC_CK stopped in Voltage switch procedure interrupt
* @arg SDMMC_IT_IDMATE: IDMA transfer error interrupt
* @arg SDMMC_IT_IDMABTC: IDMA buffer transfer complete interrupt
* @retval None
*/
#define __SDMMC_CLEAR_IT(__INSTANCE__, __INTERRUPT__) ((__INSTANCE__)->ICR = (__INTERRUPT__))
/**
* @brief Enable Start the SD I/O Read Wait operation.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_START_READWAIT_ENABLE(__INSTANCE__) ((__INSTANCE__)->DCTRL |= SDMMC_DCTRL_RWSTART)
/**
* @brief Disable Start the SD I/O Read Wait operations.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_START_READWAIT_DISABLE(__INSTANCE__) ((__INSTANCE__)->DCTRL &= ~SDMMC_DCTRL_RWSTART)
/**
* @brief Enable Start the SD I/O Read Wait operation.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_STOP_READWAIT_ENABLE(__INSTANCE__) ((__INSTANCE__)->DCTRL |= SDMMC_DCTRL_RWSTOP)
/**
* @brief Disable Stop the SD I/O Read Wait operations.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_STOP_READWAIT_DISABLE(__INSTANCE__) ((__INSTANCE__)->DCTRL &= ~SDMMC_DCTRL_RWSTOP)
/**
* @brief Enable the SD I/O Mode Operation.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_OPERATION_ENABLE(__INSTANCE__) ((__INSTANCE__)->DCTRL |= SDMMC_DCTRL_SDIOEN)
/**
* @brief Disable the SD I/O Mode Operation.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_OPERATION_DISABLE(__INSTANCE__) ((__INSTANCE__)->DCTRL &= ~SDMMC_DCTRL_SDIOEN)
/**
* @brief Enable the SD I/O Suspend command sending.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_SUSPEND_CMD_ENABLE(__INSTANCE__) ((__INSTANCE__)->CMD |= SDMMC_CMD_CMDSUSPEND)
/**
* @brief Disable the SD I/O Suspend command sending.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_SUSPEND_CMD_DISABLE(__INSTANCE__) ((__INSTANCE__)->CMD &= ~SDMMC_CMD_CMDSUSPEND)
/**
* @brief Enable the CMDTRANS mode.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_CMDTRANS_ENABLE(__INSTANCE__) ((__INSTANCE__)->CMD |= SDMMC_CMD_CMDTRANS)
/**
* @brief Disable the CMDTRANS mode.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_CMDTRANS_DISABLE(__INSTANCE__) ((__INSTANCE__)->CMD &= ~SDMMC_CMD_CMDTRANS)
/**
* @brief Enable the CMDSTOP mode.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_CMDSTOP_ENABLE(__INSTANCE__) ((__INSTANCE__)->CMD |= SDMMC_CMD_CMDSTOP)
/**
* @brief Disable the CMDSTOP mode.
* @param __INSTANCE__ : Pointer to SDMMC register base
* @retval None
*/
#define __SDMMC_CMDSTOP_DISABLE(__INSTANCE__) ((__INSTANCE__)->CMD &= ~SDMMC_CMD_CMDSTOP)
/**
* @}
*/
/**
* @}
*/
/* Exported functions --------------------------------------------------------*/
/** @addtogroup SDMMC_LL_Exported_Functions
* @{
*/
/* Initialization/de-initialization functions **********************************/
/** @addtogroup HAL_SDMMC_LL_Group1
* @{
*/
HAL_StatusTypeDef SDMMC_Init(SDMMC_TypeDef *SDMMCx, SDMMC_InitTypeDef Init);
/**
* @}
*/
/* I/O operation functions *****************************************************/
/** @addtogroup HAL_SDMMC_LL_Group2
* @{
*/
uint32_t SDMMC_ReadFIFO(SDMMC_TypeDef *SDMMCx);
HAL_StatusTypeDef SDMMC_WriteFIFO(SDMMC_TypeDef *SDMMCx, uint32_t *pWriteData);
/**
* @}
*/
/* Peripheral Control functions ************************************************/
/** @addtogroup HAL_SDMMC_LL_Group3
* @{
*/
HAL_StatusTypeDef SDMMC_PowerState_ON(SDMMC_TypeDef *SDMMCx);
HAL_StatusTypeDef SDMMC_PowerState_Cycle(SDMMC_TypeDef *SDMMCx);
HAL_StatusTypeDef SDMMC_PowerState_OFF(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_GetPowerState(SDMMC_TypeDef *SDMMCx);
/* Command path state machine (CPSM) management functions */
HAL_StatusTypeDef SDMMC_SendCommand(SDMMC_TypeDef *SDMMCx, SDMMC_CmdInitTypeDef *Command);
uint8_t SDMMC_GetCommandResponse(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_GetResponse(SDMMC_TypeDef *SDMMCx, uint32_t Response);
/* Data path state machine (DPSM) management functions */
HAL_StatusTypeDef SDMMC_ConfigData(SDMMC_TypeDef *SDMMCx, SDMMC_DataInitTypeDef* Data);
uint32_t SDMMC_GetDataCounter(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_GetFIFOCount(SDMMC_TypeDef *SDMMCx);
/* SDMMC Cards mode management functions */
HAL_StatusTypeDef SDMMC_SetSDMMCReadWaitMode(SDMMC_TypeDef *SDMMCx, uint32_t SDMMC_ReadWaitMode);
/* SDMMC Commands management functions */
uint32_t SDMMC_CmdBlockLength(SDMMC_TypeDef *SDMMCx, uint32_t BlockSize);
uint32_t SDMMC_CmdReadSingleBlock(SDMMC_TypeDef *SDMMCx, uint32_t ReadAdd);
uint32_t SDMMC_CmdReadMultiBlock(SDMMC_TypeDef *SDMMCx, uint32_t ReadAdd);
uint32_t SDMMC_CmdWriteSingleBlock(SDMMC_TypeDef *SDMMCx, uint32_t WriteAdd);
uint32_t SDMMC_CmdWriteMultiBlock(SDMMC_TypeDef *SDMMCx, uint32_t WriteAdd);
uint32_t SDMMC_CmdEraseStartAdd(SDMMC_TypeDef *SDMMCx, uint32_t StartAdd);
uint32_t SDMMC_CmdSDEraseStartAdd(SDMMC_TypeDef *SDMMCx, uint32_t StartAdd);
uint32_t SDMMC_CmdEraseEndAdd(SDMMC_TypeDef *SDMMCx, uint32_t EndAdd);
uint32_t SDMMC_CmdSDEraseEndAdd(SDMMC_TypeDef *SDMMCx, uint32_t EndAdd);
uint32_t SDMMC_CmdErase(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_CmdStopTransfer(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_CmdSelDesel(SDMMC_TypeDef *SDMMCx, uint64_t Addr);
uint32_t SDMMC_CmdGoIdleState(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_CmdOperCond(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_CmdAppCommand(SDMMC_TypeDef *SDMMCx, uint32_t Argument);
uint32_t SDMMC_CmdAppOperCommand(SDMMC_TypeDef *SDMMCx, uint32_t Argument);
uint32_t SDMMC_CmdBusWidth(SDMMC_TypeDef *SDMMCx, uint32_t BusWidth);
uint32_t SDMMC_CmdSendSCR(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_CmdSendCID(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_CmdSendCSD(SDMMC_TypeDef *SDMMCx, uint32_t Argument);
uint32_t SDMMC_CmdSetRelAdd(SDMMC_TypeDef *SDMMCx, uint16_t *pRCA);
uint32_t SDMMC_CmdSendStatus(SDMMC_TypeDef *SDMMCx, uint32_t Argument);
uint32_t SDMMC_CmdStatusRegister(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_CmdVoltageSwitch(SDMMC_TypeDef *SDMMCx);
uint32_t SDMMC_CmdOpCondition(SDMMC_TypeDef *SDMMCx, uint32_t Argument);
uint32_t SDMMC_CmdSwitch(SDMMC_TypeDef *SDMMCx, uint32_t Argument);
uint32_t SDMMC_CmdSendEXTCSD(SDMMC_TypeDef *SDMMCx, uint32_t Argument);
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
#ifdef __cplusplus
}
#endif
#endif /* STM32H7xx_LL_SDMMC_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
