mbed official
/
mbed
Important changes to repositories hosted on mbed.com
Mbed hosted mercurial repositories are deprecated and are due to be permanently deleted in July 2026.
To keep a copy of this software download the repository Zip archive or clone locally using Mercurial.
It is also possible to export all your personal repositories from the account settings page.
Dependents: hello SerialTestv11 SerialTestv12 Sierpinski ... more
Diff: TARGET_B96B_F446VE/stm32f4xx_hal_conf.h
- Revision:
- 122:f9eeca106725
- Parent:
- 112:6f327212ef96
--- a/TARGET_B96B_F446VE/stm32f4xx_hal_conf.h Wed May 25 16:44:06 2016 +0100
+++ b/TARGET_B96B_F446VE/stm32f4xx_hal_conf.h Thu Jul 07 14:34:11 2016 +0100
@@ -2,15 +2,15 @@
******************************************************************************
* @file stm32f4xx_hal_conf.h
* @author MCD Application Team
- * @version V1.3.2
- * @date 26-June-2015
+ * @version V1.4.4
+ * @date 22-January-2016
* @brief HAL configuration template file.
* This file should be copied to the application folder and renamed
* to stm32f4xx_hal_conf.h.
******************************************************************************
* @attention
*
- * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
+ * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
@@ -53,48 +53,49 @@
* @brief This is the list of modules to be used in the HAL driver
*/
#define HAL_MODULE_ENABLED
-#define HAL_ADC_MODULE_ENABLED
-#define HAL_CAN_MODULE_ENABLED
-#define HAL_CRC_MODULE_ENABLED
+#define HAL_ADC_MODULE_ENABLED
+#define HAL_CAN_MODULE_ENABLED
+#define HAL_CRC_MODULE_ENABLED
#define HAL_CEC_MODULE_ENABLED
-#define HAL_CRYP_MODULE_ENABLED
-#define HAL_DAC_MODULE_ENABLED
-#define HAL_DCMI_MODULE_ENABLED
+#define HAL_CRYP_MODULE_ENABLED
+#define HAL_DAC_MODULE_ENABLED
+#define HAL_DCMI_MODULE_ENABLED
#define HAL_DMA_MODULE_ENABLED
-#define HAL_DMA2D_MODULE_ENABLED
-#define HAL_ETH_MODULE_ENABLED
-#define HAL_FLASH_MODULE_ENABLED
+#define HAL_DMA2D_MODULE_ENABLED
+#define HAL_ETH_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
#define HAL_NAND_MODULE_ENABLED
#define HAL_NOR_MODULE_ENABLED
#define HAL_PCCARD_MODULE_ENABLED
#define HAL_SRAM_MODULE_ENABLED
#define HAL_SDRAM_MODULE_ENABLED
-#define HAL_HASH_MODULE_ENABLED
+#define HAL_HASH_MODULE_ENABLED
#define HAL_GPIO_MODULE_ENABLED
#define HAL_I2C_MODULE_ENABLED
-#define HAL_I2S_MODULE_ENABLED
-#define HAL_IWDG_MODULE_ENABLED
-#define HAL_LTDC_MODULE_ENABLED
-#define HAL_PWR_MODULE_ENABLED
-#define HAL_QSPI_MODULE_ENABLED
-#define HAL_RCC_MODULE_ENABLED
-#define HAL_RNG_MODULE_ENABLED
+#define HAL_I2S_MODULE_ENABLED
+#define HAL_IWDG_MODULE_ENABLED
+#define HAL_LTDC_MODULE_ENABLED
+#define HAL_DSI_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_QSPI_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_RNG_MODULE_ENABLED
#define HAL_RTC_MODULE_ENABLED
-#define HAL_SAI_MODULE_ENABLED
-#define HAL_SD_MODULE_ENABLED
-#define HAL_SPI_MODULE_ENABLED
-#define HAL_TIM_MODULE_ENABLED
-#define HAL_UART_MODULE_ENABLED
-#define HAL_USART_MODULE_ENABLED
-#define HAL_IRDA_MODULE_ENABLED
-#define HAL_SMARTCARD_MODULE_ENABLED
-#define HAL_WWDG_MODULE_ENABLED
+#define HAL_SAI_MODULE_ENABLED
+#define HAL_SD_MODULE_ENABLED
+#define HAL_SPI_MODULE_ENABLED
+#define HAL_TIM_MODULE_ENABLED
+#define HAL_UART_MODULE_ENABLED
+#define HAL_USART_MODULE_ENABLED
+#define HAL_IRDA_MODULE_ENABLED
+#define HAL_SMARTCARD_MODULE_ENABLED
+#define HAL_WWDG_MODULE_ENABLED
#define HAL_CORTEX_MODULE_ENABLED
#define HAL_PCD_MODULE_ENABLED
#define HAL_HCD_MODULE_ENABLED
#define HAL_FMPI2C_MODULE_ENABLED
#define HAL_SPDIFRX_MODULE_ENABLED
-
+#define HAL_LPTIM_MODULE_ENABLED
/* ########################## HSE/HSI Values adaptation ##################### */
/**
@@ -103,11 +104,11 @@
* (when HSE is used as system clock source, directly or through the PLL).
*/
#if !defined (HSE_VALUE)
- #define HSE_VALUE ((uint32_t)16000000) /*!< Value of the External oscillator in Hz */
+ #define HSE_VALUE ((uint32_t)16000000U) /*!< Value of the External oscillator in Hz */
#endif /* HSE_VALUE */
#if !defined (HSE_STARTUP_TIMEOUT)
- #define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */
+ #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */
#endif /* HSE_STARTUP_TIMEOUT */
/**
@@ -116,14 +117,14 @@
* (when HSI is used as system clock source, directly or through the PLL).
*/
#if !defined (HSI_VALUE)
- #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
+ #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
#endif /* HSI_VALUE */
/**
* @brief Internal Low Speed oscillator (LSI) value.
*/
#if !defined (LSI_VALUE)
- #define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/
+ #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/
#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
The real value may vary depending on the variations
in voltage and temperature.*/
@@ -131,16 +132,20 @@
* @brief External Low Speed oscillator (LSE) value.
*/
#if !defined (LSE_VALUE)
- #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */
+ #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */
#endif /* LSE_VALUE */
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
/**
* @brief External clock source for I2S peripheral
* This value is used by the I2S HAL module to compute the I2S clock source
* frequency, this source is inserted directly through I2S_CKIN pad.
*/
#if !defined (EXTERNAL_CLOCK_VALUE)
- #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the Internal oscillator in Hz*/
+ #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/
#endif /* EXTERNAL_CLOCK_VALUE */
/* Tip: To avoid modifying this file each time you need to use different HSE,
@@ -150,85 +155,94 @@
/**
* @brief This is the HAL system configuration section
*/
-#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
-#define TICK_INT_PRIORITY ((uint32_t)0x0F) /*!< tick interrupt priority */
-#define USE_RTOS 0
-#define PREFETCH_ENABLE 1
-#define INSTRUCTION_CACHE_ENABLE 1
-#define DATA_CACHE_ENABLE 1
+#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)0x0FU) /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define INSTRUCTION_CACHE_ENABLE 1U
+#define DATA_CACHE_ENABLE 1U
/* ########################## Assert Selection ############################## */
/**
* @brief Uncomment the line below to expanse the "assert_param" macro in the
* HAL drivers code
*/
-/* #define USE_FULL_ASSERT 1 */
+/* #define USE_FULL_ASSERT 1U */
/* ################## Ethernet peripheral configuration ##################### */
/* Section 1 : Ethernet peripheral configuration */
/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
-#define MAC_ADDR0 2
-#define MAC_ADDR1 0
-#define MAC_ADDR2 0
-#define MAC_ADDR3 0
-#define MAC_ADDR4 0
-#define MAC_ADDR5 0
+#define MAC_ADDR0 2U
+#define MAC_ADDR1 0U
+#define MAC_ADDR2 0U
+#define MAC_ADDR3 0U
+#define MAC_ADDR4 0U
+#define MAC_ADDR5 0U
/* Definition of the Ethernet driver buffers size and count */
#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
-#define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
-#define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
+#define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
/* Section 2: PHY configuration section */
/* DP83848 PHY Address*/
-#define DP83848_PHY_ADDRESS 0x01
+#define DP83848_PHY_ADDRESS 0x01U
/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
-#define PHY_RESET_DELAY ((uint32_t)0x000000FF)
+#define PHY_RESET_DELAY ((uint32_t)0x000000FFU)
/* PHY Configuration delay */
-#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
+#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU)
-#define PHY_READ_TO ((uint32_t)0x0000FFFF)
-#define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
+#define PHY_READ_TO ((uint32_t)0x0000FFFFU)
+#define PHY_WRITE_TO ((uint32_t)0x0000FFFFU)
/* Section 3: Common PHY Registers */
-#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
-#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
+#define PHY_BCR ((uint16_t)0x0000U) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x0001U) /*!< Transceiver Basic Status Register */
-#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
-#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
-#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
-#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
-#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
-#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
-#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
-#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
-#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
-#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
+#define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */
+#define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */
+#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */
+#define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */
+#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */
+#define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */
+#define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */
-#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
-#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
-#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
+#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */
+#define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */
+#define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */
/* Section 4: Extended PHY Registers */
-#define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */
-#define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */
-#define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */
+#define PHY_SR ((uint16_t)0x0010U) /*!< PHY status register Offset */
+#define PHY_MICR ((uint16_t)0x0011U) /*!< MII Interrupt Control Register */
+#define PHY_MISR ((uint16_t)0x0012U) /*!< MII Interrupt Status and Misc. Control Register */
-#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */
-#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */
-#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */
+#define PHY_LINK_STATUS ((uint16_t)0x0001U) /*!< PHY Link mask */
+#define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */
+#define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */
+
+#define PHY_MICR_INT_EN ((uint16_t)0x0002U) /*!< PHY Enable interrupts */
+#define PHY_MICR_INT_OE ((uint16_t)0x0001U) /*!< PHY Enable output interrupt events */
-#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */
-#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */
+#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020U) /*!< Enable Interrupt on change of link status */
+#define PHY_LINK_INTERRUPT ((uint16_t)0x2000U) /*!< PHY link status interrupt mask */
+
+/* ################## SPI peripheral configuration ########################## */
-#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */
-#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 1U
/* Includes ------------------------------------------------------------------*/
/**
@@ -305,7 +319,7 @@
#ifdef HAL_SDRAM_MODULE_ENABLED
#include "stm32f4xx_hal_sdram.h"
-#endif /* HAL_SDRAM_MODULE_ENABLED */
+#endif /* HAL_SDRAM_MODULE_ENABLED */
#ifdef HAL_HASH_MODULE_ENABLED
#include "stm32f4xx_hal_hash.h"
@@ -383,6 +397,10 @@
#include "stm32f4xx_hal_hcd.h"
#endif /* HAL_HCD_MODULE_ENABLED */
+#ifdef HAL_DSI_MODULE_ENABLED
+ #include "stm32f4xx_hal_dsi.h"
+#endif /* HAL_DSI_MODULE_ENABLED */
+
#ifdef HAL_QSPI_MODULE_ENABLED
#include "stm32f4xx_hal_qspi.h"
#endif /* HAL_QSPI_MODULE_ENABLED */
@@ -398,7 +416,11 @@
#ifdef HAL_SPDIFRX_MODULE_ENABLED
#include "stm32f4xx_hal_spdifrx.h"
#endif /* HAL_SPDIFRX_MODULE_ENABLED */
-
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+ #include "stm32f4xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
/* Exported macro ------------------------------------------------------------*/
#ifdef USE_FULL_ASSERT
/**
