mbed official
The official Mbed 2 C/C++ SDK provides the software platform and libraries to build your applications.
Dependents: hello SerialTestv11 SerialTestv12 Sierpinski ... more
mbed 2
This is the mbed 2 library. If you'd like to learn about Mbed OS please see the mbed-os docs.
Diff: TARGET_DISCO_F303VC/TARGET_STM/TARGET_STM32F3/device/stm32f3xx_hal_hrtim.h
- Revision:
- 168:b9e159c1930a
- Parent:
- 163:e59c8e839560
--- a/TARGET_DISCO_F303VC/TARGET_STM/TARGET_STM32F3/device/stm32f3xx_hal_hrtim.h Fri May 11 16:51:14 2018 +0100
+++ b/TARGET_DISCO_F303VC/TARGET_STM/TARGET_STM32F3/device/stm32f3xx_hal_hrtim.h Thu May 24 15:35:55 2018 +0100
@@ -2,8 +2,6 @@
******************************************************************************
* @file stm32f3xx_hal_hrtim.h
* @author MCD Application Team
- * @version V1.4.0
- * @date 16-December-2016
* @brief Header file of HRTIM HAL module.
******************************************************************************
* @attention
@@ -1330,8 +1328,9 @@
* @brief Constants defining whether or not an external event is programmed in
fast mode
*/
-#define HRTIM_EVENTFASTMODE_DISABLE (0x00000000U) /*!< External Event is acting asynchronously on outputs (low latency mode) */
-#define HRTIM_EVENTFASTMODE_ENABLE (HRTIM_EECR1_EE1FAST) /*!< External Event is re-synchronized by the HRTIM logic before acting on outputs */
+
+#define HRTIM_EVENTFASTMODE_ENABLE (0x00000000U) /*!< External Event is re-synchronized by the HRTIM logic before acting on outputs */
+#define HRTIM_EVENTFASTMODE_DISABLE (HRTIM_EECR1_EE1FAST) /*!< External Event is acting asynchronously on outputs (low latency mode) */
/**
* @}
*/
@@ -2701,14 +2700,14 @@
*/
/** @brief Reset HRTIM handle state
- * @param __HANDLE__: HRTIM handle.
+ * @param __HANDLE__ HRTIM handle.
* @retval None
*/
#define __HAL_HRTIM_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_HRTIM_STATE_RESET)
/** @brief Enables or disables the timer counter(s)
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __TIMERS__: timers to enable/disable
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __TIMERS__ timers to enable/disable
* This parameter can be any combinations of the following values:
* @arg HRTIM_TIMERID_MASTER: Master timer identifier
* @arg HRTIM_TIMERID_TIMER_A: Timer A identifier
@@ -2771,8 +2770,8 @@
} while(0U)
/** @brief Enables or disables the specified HRTIM common interrupts.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __INTERRUPT__: specifies the interrupt source to enable or disable.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __INTERRUPT__ specifies the interrupt source to enable or disable.
* This parameter can be one of the following values:
* @arg HRTIM_IT_FLT1: Fault 1 interrupt enable
* @arg HRTIM_IT_FLT2: Fault 2 interrupt enable
@@ -2788,8 +2787,8 @@
#define __HAL_HRTIM_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->sCommonRegs.IER &= ~(__INTERRUPT__))
/** @brief Enables or disables the specified HRTIM Master timer interrupts.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __INTERRUPT__: specifies the interrupt source to enable or disable.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __INTERRUPT__ specifies the interrupt source to enable or disable.
* This parameter can be one of the following values:
* @arg HRTIM_MASTER_IT_MCMP1: Master compare 1 interrupt enable
* @arg HRTIM_MASTER_IT_MCMP2: Master compare 2 interrupt enable
@@ -2804,9 +2803,9 @@
#define __HAL_HRTIM_MASTER_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->sMasterRegs.MDIER &= ~(__INTERRUPT__))
/** @brief Enables or disables the specified HRTIM Timerx interrupts.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __TIMER__: specified the timing unit (Timer A to E)
- * @param __INTERRUPT__: specifies the interrupt source to enable or disable.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __TIMER__ specified the timing unit (Timer A to E)
+ * @param __INTERRUPT__ specifies the interrupt source to enable or disable.
* This parameter can be one of the following values:
* @arg HRTIM_TIM_IT_CMP1: Timer compare 1 interrupt enable
* @arg HRTIM_TIM_IT_CMP2: Timer compare 2 interrupt enable
@@ -2828,8 +2827,8 @@
#define __HAL_HRTIM_TIMER_DISABLE_IT(__HANDLE__, __TIMER__, __INTERRUPT__) ((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].TIMxDIER &= ~(__INTERRUPT__))
/** @brief Checks if the specified HRTIM common interrupt source is enabled or disabled.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __INTERRUPT__: specifies the interrupt source to check.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __INTERRUPT__ specifies the interrupt source to check.
* This parameter can be one of the following values:
* @arg HRTIM_IT_FLT1: Fault 1 interrupt enable
* @arg HRTIM_IT_FLT2: Fault 2 interrupt enable
@@ -2844,8 +2843,8 @@
#define __HAL_HRTIM_GET_ITSTATUS(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->sCommonRegs.IER & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
/** @brief Checks if the specified HRTIM Master interrupt source is enabled or disabled.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __INTERRUPT__: specifies the interrupt source to check.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __INTERRUPT__ specifies the interrupt source to check.
* This parameter can be one of the following values:
* @arg HRTIM_MASTER_IT_MCMP1: Master compare 1 interrupt enable
* @arg HRTIM_MASTER_IT_MCMP2: Master compare 2 interrupt enable
@@ -2859,9 +2858,9 @@
#define __HAL_HRTIM_MASTER_GET_ITSTATUS(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->sMasterRegs.MDIER & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
/** @brief Checks if the specified HRTIM Timerx interrupt source is enabled or disabled.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __TIMER__: specified the timing unit (Timer A to E)
- * @param __INTERRUPT__: specifies the interrupt source to check.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __TIMER__ specified the timing unit (Timer A to E)
+ * @param __INTERRUPT__ specifies the interrupt source to check.
* This parameter can be one of the following values:
* @arg HRTIM_MASTER_IT_MCMP1: Master compare 1 interrupt enable
* @arg HRTIM_MASTER_IT_MCMP2: Master compare 2 interrupt enable
@@ -2889,8 +2888,8 @@
#define __HAL_HRTIM_TIMER_GET_ITSTATUS(__HANDLE__, __TIMER__, __INTERRUPT__) ((((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].TIMxDIER & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
/** @brief Clears the specified HRTIM common pending flag.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __INTERRUPT__: specifies the interrupt pending bit to clear.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __INTERRUPT__ specifies the interrupt pending bit to clear.
* This parameter can be one of the following values:
* @arg HRTIM_IT_FLT1: Fault 1 interrupt clear flag
* @arg HRTIM_IT_FLT2: Fault 2 interrupt clear flag
@@ -2905,8 +2904,8 @@
#define __HAL_HRTIM_CLEAR_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->sCommonRegs.ICR = (__INTERRUPT__))
/** @brief Clears the specified HRTIM Master pending flag.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __INTERRUPT__: specifies the interrupt pending bit to clear.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __INTERRUPT__ specifies the interrupt pending bit to clear.
* This parameter can be one of the following values:
* @arg HRTIM_MASTER_IT_MCMP1: Master compare 1 interrupt clear flag
* @arg HRTIM_MASTER_IT_MCMP2: Master compare 2 interrupt clear flag
@@ -2920,9 +2919,9 @@
#define __HAL_HRTIM_MASTER_CLEAR_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->sMasterRegs.MICR = (__INTERRUPT__))
/** @brief Clears the specified HRTIM Timerx pending flag.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __TIMER__: specified the timing unit (Timer A to E)
- * @param __INTERRUPT__: specifies the interrupt pending bit to clear.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __TIMER__ specified the timing unit (Timer A to E)
+ * @param __INTERRUPT__ specifies the interrupt pending bit to clear.
* This parameter can be one of the following values:
* @arg HRTIM_TIM_IT_CMP1: Timer compare 1 interrupt clear flag
* @arg HRTIM_TIM_IT_CMP2: Timer compare 2 interrupt clear flag
@@ -2944,8 +2943,8 @@
/* DMA HANDLING */
/** @brief Enables or disables the specified HRTIM common interrupts.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __INTERRUPT__: specifies the interrupt source to enable or disable.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __INTERRUPT__ specifies the interrupt source to enable or disable.
* This parameter can be one of the following values:
* @arg HRTIM_IT_FLT1: Fault 1 interrupt enable
* @arg HRTIM_IT_FLT2: Fault 2 interrupt enable
@@ -2961,8 +2960,8 @@
#define __HAL_HRTIM_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((__HANDLE__)->Instance->sCommonRegs.IER &= ~(__INTERRUPT__))
/** @brief Enables or disables the specified HRTIM Master timer DMA requets.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __DMA__: specifies the DMA request to enable or disable.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __DMA__ specifies the DMA request to enable or disable.
* This parameter can be one of the following values:
* @arg HRTIM_MASTER_DMA_MCMP1: Master compare 1 DMA resquest enable
* @arg HRTIM_MASTER_DMA_MCMP2: Master compare 2 DMA resquest enable
@@ -2977,9 +2976,9 @@
#define __HAL_HRTIM_MASTER_DISABLE_DMA(__HANDLE__, __DMA__) ((__HANDLE__)->Instance->sMasterRegs.MDIER &= ~(__DMA__))
/** @brief Enables or disables the specified HRTIM Timerx DMA requests.
- * @param __HANDLE__: specifies the HRTIM Handle.
- * @param __TIMER__: specified the timing unit (Timer A to E)
- * @param __DMA__: specifies the DMA request to enable or disable.
+ * @param __HANDLE__ specifies the HRTIM Handle.
+ * @param __TIMER__ specified the timing unit (Timer A to E)
+ * @param __DMA__ specifies the DMA request to enable or disable.
* This parameter can be one of the following values:
* @arg HRTIM_TIM_DMA_CMP1: Timer compare 1 DMA resquest enable
* @arg HRTIM_TIM_DMA_CMP2: Timer compare 2 DMA resquest enable
@@ -3010,12 +3009,12 @@
#define __HAL_HRTIM_TIMER_CLEAR_FLAG(__HANDLE__, __TIMER__, __FLAG__) ((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].TIMxICR = (__FLAG__))
/** @brief Sets the HRTIM timer Counter Register value on runtime
- * @param __HANDLE__: HRTIM Handle.
- * @param __TIMER__: HRTIM timer
+ * @param __HANDLE__ HRTIM Handle.
+ * @param __TIMER__ HRTIM timer
* This parameter can be one of the following values:
* @arg 0x5 for master timer
* @arg 0x0 to 0x4 for timers A to E
- * @param __COUNTER__: specifies the Counter Register new value.
+ * @param __COUNTER__ specifies the Counter Register new value.
* @retval None
*/
#define __HAL_HRTIM_SETCOUNTER(__HANDLE__, __TIMER__, __COUNTER__) \
@@ -3023,8 +3022,8 @@
((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].CNTxR = (__COUNTER__)))
/** @brief Gets the HRTIM timer Counter Register value on runtime
- * @param __HANDLE__: HRTIM Handle.
- * @param __TIMER__: HRTIM timer
+ * @param __HANDLE__ HRTIM Handle.
+ * @param __TIMER__ HRTIM timer
* This parameter can be one of the following values:
* @arg 0x5 for master timer
* @arg 0x0 to 0x4 for timers A to E
@@ -3035,12 +3034,12 @@
((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].CNTxR))
/** @brief Sets the HRTIM timer Period value on runtime
- * @param __HANDLE__: HRTIM Handle.
- * @param __TIMER__: HRTIM timer
+ * @param __HANDLE__ HRTIM Handle.
+ * @param __TIMER__ HRTIM timer
* This parameter can be one of the following values:
* @arg 0x5 for master timer
* @arg 0x0 to 0x4 for timers A to E
- * @param __PERIOD__: specifies the Period Register new value.
+ * @param __PERIOD__ specifies the Period Register new value.
* @retval None
*/
#define __HAL_HRTIM_SETPERIOD(__HANDLE__, __TIMER__, __PERIOD__) \
@@ -3048,8 +3047,8 @@
((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].PERxR = (__PERIOD__)))
/** @brief Gets the HRTIM timer Period Register value on runtime
- * @param __HANDLE__: HRTIM Handle.
- * @param __TIMER__: HRTIM timer
+ * @param __HANDLE__ HRTIM Handle.
+ * @param __TIMER__ HRTIM timer
* This parameter can be one of the following values:
* @arg 0x5 for master timer
* @arg 0x0 to 0x4 for timers A to E
@@ -3060,12 +3059,12 @@
((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].PERxR))
/** @brief Sets the HRTIM timer clock prescaler value on runtime
- * @param __HANDLE__: HRTIM Handle.
- * @param __TIMER__: HRTIM timer
+ * @param __HANDLE__ HRTIM Handle.
+ * @param __TIMER__ HRTIM timer
* This parameter can be one of the following values:
* @arg 0x5 for master timer
* @arg 0x0 to 0x4 for timers A to E
- * @param __PRESCALER__: specifies the clock prescaler new value.
+ * @param __PRESCALER__ specifies the clock prescaler new value.
* This parameter can be one of the following values:
* @arg HRTIM_PRESCALERRATIO_MUL32: fHRCK: 4.608 GHz - Resolution: 217 ps - Min PWM frequency: 70.3 kHz (fHRTIM=144MHz)
* @arg HRTIM_PRESCALERRATIO_MUL16: fHRCK: 2.304 GHz - Resolution: 434 ps - Min PWM frequency: 35.1 KHz (fHRTIM=144MHz)
@@ -3078,12 +3077,12 @@
* @retval None
*/
#define __HAL_HRTIM_SETCLOCKPRESCALER(__HANDLE__, __TIMER__, __PRESCALER__) \
- (((__TIMER__) == HRTIM_TIMERINDEX_MASTER) ? ((__HANDLE__)->Instance->sMasterRegs.MCR |= (__PRESCALER__)) :\
- ((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].TIMxCR |= (__PRESCALER__)))
+ (((__TIMER__) == HRTIM_TIMERINDEX_MASTER) ? (MODIFY_REG((__HANDLE__)->Instance->sMasterRegs.MCR, HRTIM_MCR_CK_PSC, (__PRESCALER__))) :\
+ (MODIFY_REG((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].TIMxCR, HRTIM_TIMCR_CK_PSC, (__PRESCALER__))))
/** @brief Gets the HRTIM timer clock prescaler value on runtime
- * @param __HANDLE__: HRTIM Handle.
- * @param __TIMER__: HRTIM timer
+ * @param __HANDLE__ HRTIM Handle.
+ * @param __TIMER__ HRTIM timer
* This parameter can be one of the following values:
* @arg 0x5 for master timer
* @arg 0x0 to 0x4 for timers A to E
@@ -3094,17 +3093,17 @@
((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].TIMxCR & HRTIM_TIMCR_CK_PSC))
/** @brief Sets the HRTIM timer Compare Register value on runtime
- * @param __HANDLE__: HRTIM Handle.
- * @param __TIMER__: HRTIM timer
+ * @param __HANDLE__ HRTIM Handle.
+ * @param __TIMER__ HRTIM timer
* This parameter can be one of the following values:
* @arg 0x0 to 0x4 for timers A to E
- * @param __COMPAREUNIT__: timer compare unit
+ * @param __COMPAREUNIT__ timer compare unit
* This parameter can be one of the following values:
* @arg HRTIM_COMPAREUNIT_1: Compare unit 1
* @arg HRTIM_COMPAREUNIT_2: Compare unit 2
* @arg HRTIM_COMPAREUNIT_3: Compare unit 3
* @arg HRTIM_COMPAREUNIT_4: Compare unit 4
- * @param __COMPARE__: specifies the Compare new value.
+ * @param __COMPARE__ specifies the Compare new value.
* @retval None
*/
#define __HAL_HRTIM_SETCOMPARE(__HANDLE__, __TIMER__, __COMPAREUNIT__, __COMPARE__) \
@@ -3120,11 +3119,11 @@
((__HANDLE__)->Instance->sTimerxRegs[(__TIMER__)].CMP4xR = (__COMPARE__))))
/** @brief Gets the HRTIM timer Compare Register value on runtime
- * @param __HANDLE__: HRTIM Handle.
- * @param __TIMER__: HRTIM timer
+ * @param __HANDLE__ HRTIM Handle.
+ * @param __TIMER__ HRTIM timer
* This parameter can be one of the following values:
* @arg 0x0 to 0x4 for timers A to E
- * @param __COMPAREUNIT__: timer compare unit
+ * @param __COMPAREUNIT__ timer compare unit
* This parameter can be one of the following values:
* @arg HRTIM_COMPAREUNIT_1: Compare unit 1
* @arg HRTIM_COMPAREUNIT_2: Compare unit 2
