Diff: TARGET_NUMAKER_PFM_M453/TOOLCHAIN_ARM_STD/m451_scuart.h

Revision:

171:3a7713b1edbc

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/TARGET_NUMAKER_PFM_M453/TOOLCHAIN_ARM_STD/m451_scuart.h	Thu Nov 08 11:45:42 2018 +0000
@@ -0,0 +1,279 @@
+/**************************************************************************//**
+ * @file     sc.h
+ * @version  V3.00
+ * $Revision: 7 $
+ * $Date: 15/08/11 10:26a $
+ * @brief    M451 series Smartcard UART mode (SCUART) driver header file
+ *
+ * @note
+ * Copyright (C) 2013~2015 Nuvoton Technology Corp. All rights reserved.
+ *****************************************************************************/
+#ifndef __SCUART_H__
+#define __SCUART_H__
+
+#ifdef __cplusplus
+extern "C"
+{
+#endif
+
+
+/** @addtogroup Standard_Driver Standard Driver
+  @{
+*/
+
+/** @addtogroup SCUART_Driver SCUART Driver
+  @{
+*/
+
+/** @addtogroup SCUART_EXPORTED_CONSTANTS SCUART Exported Constants
+  @{
+*/
+#define SCUART_CHAR_LEN_5     (0x3ul << SC_UARTCTL_WLS_Pos)  /*!< Set SCUART word length to 5 bits */
+#define SCUART_CHAR_LEN_6     (0x2ul << SC_UARTCTL_WLS_Pos)  /*!< Set SCUART word length to 6 bits */
+#define SCUART_CHAR_LEN_7     (0x1ul << SC_UARTCTL_WLS_Pos)  /*!< Set SCUART word length to 7 bits */
+#define SCUART_CHAR_LEN_8     (0)                            /*!< Set SCUART word length to 8 bits */
+
+#define SCUART_PARITY_NONE    (SC_UARTCTL_PBOFF_Msk)         /*!< Set SCUART transfer with no parity   */
+#define SCUART_PARITY_ODD     (SC_UARTCTL_OPE_Msk)           /*!< Set SCUART transfer with odd parity  */
+#define SCUART_PARITY_EVEN    (0)                            /*!< Set SCUART transfer with even parity */
+
+#define SCUART_STOP_BIT_1     (SC_CTL_NSB_Msk)                 /*!< Set SCUART transfer with one stop bit  */
+#define SCUART_STOP_BIT_2     (0)                               /*!< Set SCUART transfer with two stop bits */
+
+
+/*@}*/ /* end of group SCUART_EXPORTED_CONSTANTS */
+
+
+/** @addtogroup SCUART_EXPORTED_FUNCTIONS SCUART Exported Functions
+  @{
+*/
+
+/* TX Macros */
+/**
+  * @brief Write Data to Tx data register.
+  * @param[in] sc The pointer of smartcard module.
+  * @param[in] u8Data Data byte to transmit.
+  * @return None
+  * @details By writing data to DAT register, the SC will send out an 8-bit data.
+  * \hideinitializer
+  */
+#define SCUART_WRITE(sc, u8Data) ((sc)-> DAT = (u8Data))
+
+/**
+  * @brief Get TX FIFO empty flag status from register.
+  * @param[in] sc The pointer of smartcard module.
+  * @return Transmit FIFO empty status.
+  * @retval 0 Transmit FIFO is not empty.
+  * @retval SC_STATUS_TXEMPTY_Msk Transmit FIFO is empty.
+  * @details When the last byte of TX buffer has been transferred to Transmitter Shift Register, hardware sets TXEMPTY bit (SC_STATUS[9]) high.
+  *          It will be cleared when writing data into DAT (SC_DAT[7:0]).
+  * \hideinitializer
+  */
+#define SCUART_GET_TX_EMPTY(sc) ((sc)->STATUS & SC_STATUS_TXEMPTY_Msk)
+
+/**
+  * @brief Get TX FIFO full flag status from register.
+  * @param[in] sc The pointer of smartcard module.
+  * @retval 0 Transmit FIFO is not full.
+  * @retval SC_STATUS_TXFULL_Msk Transmit FIFO is full.
+  * @details TXFULL(SC_STATUS[10]) is set when TX pointer is equal to 4, otherwise is cleared by hardware.
+  * \hideinitializer
+  */
+#define SCUART_GET_TX_FULL(sc) ((sc)->STATUS & SC_STATUS_TXFULL_Msk)
+
+/**
+  * @brief Wait specified smartcard port transmission complete.
+  * @param[in] sc The pointer of smartcard module.
+  * @return None
+  * @details TXACT (SC_STATUS[31]) is cleared automatically when TX transfer is finished or the last byte transmission has completed.
+  * @note This macro blocks until transmit complete.
+  * \hideinitializer
+  */
+#define SCUART_WAIT_TX_EMPTY(sc) while((sc)->STATUS & SC_STATUS_TXACT_Msk)
+
+/**
+  * @brief Check specified smartcard port transmit FIFO is full or not.
+  * @param[in] sc The pointer of smartcard module.
+  * @retval 0 Transmit FIFO is not full.
+  * @retval 1 Transmit FIFO is full.
+  * @details TXFULL(SC_STATUS[10]) indicates TX buffer full or not.
+  *          This is set when TX pointer is equal to 4, otherwise is cleared by hardware.
+  * \hideinitializer
+  */
+#define SCUART_IS_TX_FULL(sc) ((sc)->STATUS & SC_STATUS_TXFULL_Msk ? 1 : 0)
+
+/**
+  * @brief Check specified smartcard port transmission is over.
+  * @param[in] sc The pointer of smartcard module.
+  * @retval 0 Transmit is not complete.
+  * @retval 1 Transmit complete.
+  * @details TXACT (SC_STATUS[31]) is set by hardware when TX transfer is in active and the STOP bit of the last byte has been transmitted.
+  * \hideinitializer
+  */
+#define SCUART_IS_TX_EMPTY(sc) ((sc)->STATUS & SC_STATUS_TXACT_Msk ? 0 : 1)
+
+
+/* RX Macros */
+
+/**
+  * @brief Read Rx data register.
+  * @param[in] sc The pointer of smartcard module.
+  * @return The oldest data byte in RX FIFO.
+  * @details By reading DAT register, the SC will return an 8-bit received data.
+  * \hideinitializer
+  */
+#define SCUART_READ(sc) ((sc)->DAT)
+
+/**
+  * @brief Get RX FIFO empty flag status from register.
+  * @param[in] sc The pointer of smartcard module.
+  * @retval 0 Receive FIFO is not empty.
+  * @retval SC_STATUS_RXEMPTY_Msk Receive FIFO is empty.
+  * @details When the last byte of Rx buffer has been read by CPU, hardware sets RXEMPTY(SC_STATUS[1]) high.
+  *          It will be cleared when SC receives any new data.
+  * \hideinitializer
+  */
+#define SCUART_GET_RX_EMPTY(sc) ((sc)->STATUS & SC_STATUS_RXEMPTY_Msk)
+
+
+/**
+  * @brief Get RX FIFO full flag status from register.
+  * @param[in] sc The pointer of smartcard module.
+  * @retval 0 Receive FIFO is not full.
+  * @retval SC_STATUS_TXFULL_Msk Receive FIFO is full.
+  * @details RXFULLF(SC_STATUS[2]) is set when RX pointer is equal to 4, otherwise it is cleared by hardware.
+  * \hideinitializer
+  */
+#define SCUART_GET_RX_FULL(sc) ((sc)->STATUS & SC_STATUS_RXFULL_Msk)
+
+/**
+  * @brief Check if receive data number in FIFO reach FIFO trigger level or not.
+  * @param[in] sc The pointer of smartcard module.
+  * @retval 0 The number of bytes in receive FIFO is less than trigger level.
+  * @retval 1 The number of bytes in receive FIFO equals or larger than trigger level.
+  * @details RDAIF(SC_INTSTS[0]) is used for received data reaching trigger level RXTRGLV (SC_CTL[7:6]) interrupt status flag.
+  * @note If receive trigger level is \b not 1 byte, this macro return 0 does not necessary indicates there is no data in FIFO.
+  * \hideinitializer
+  */
+#define SCUART_IS_RX_READY(sc) ((sc)->INTSTS & SC_INTSTS_RDAIF_Msk ? 1 : 0)
+
+/**
+  * @brief Check specified smartcard port receive FIFO is full or not.
+  * @param[in] sc The pointer of smartcard module.
+  * @retval 0 Receive FIFO is not full.
+  * @retval 1 Receive FIFO is full.
+  * @details RXFULLF(SC_STATUS[2]) is set when RX pointer is equal to 4, otherwise it is cleared by hardware.
+  * \hideinitializer
+  */
+#define SCUART_IS_RX_FULL(sc) ((sc)->STATUS & SC_STATUS_RXFULL_Msk ? 1 : 0)
+
+/* Interrupt Macros */
+
+/**
+  * @brief Enable specified interrupts.
+  * @param[in] sc The pointer of smartcard module.
+  * @param[in] u32Mask Interrupt masks to enable, a combination of following bits.
+  *             - \ref SC_INTEN_RXTOIF_Msk
+  *             - \ref SC_INTEN_TERRIEN_Msk
+  *             - \ref SC_INTEN_TBEIEN_Msk
+  *             - \ref SC_INTEN_RDAIEN_Msk
+  * @return None
+  * @details The macro is used to enable receiver buffer time-out interrupt, transfer error interrupt,
+  *          transmit buffer empty interrupt or receive data reach trigger level interrupt.
+  * \hideinitializer
+  */
+#define SCUART_ENABLE_INT(sc, u32Mask) ((sc)->INTEN |= (u32Mask))
+
+/**
+  * @brief Disable specified interrupts.
+  * @param[in] sc The pointer of smartcard module.
+  * @param[in] u32Mask Interrupt masks to disable, a combination of following bits.
+  *             - \ref SC_INTEN_RXTOIF_Msk
+  *             - \ref SC_INTEN_TERRIEN_Msk
+  *             - \ref SC_INTEN_TBEIEN_Msk
+  *             - \ref SC_INTEN_RDAIEN_Msk
+  * @return None
+  * @details The macro is used to disable receiver buffer time-out interrupt, transfer error interrupt,
+  *          transmit buffer empty interrupt or receive data reach trigger level interrupt.
+  * \hideinitializer
+  */
+#define SCUART_DISABLE_INT(sc, u32Mask) ((sc)->INTEN &= ~(u32Mask))
+
+/**
+  * @brief Get specified interrupt flag/status.
+  * @param[in] sc The pointer of smartcard module.
+  * @param[in] u32Type Interrupt flag/status to check, could be one of following value:
+  *             - \ref SC_INTSTS_RBTOIF_Msk
+  *             - \ref SC_INTSTS_TERRIF_Msk
+  *             - \ref SC_INTSTS_TBEIF_Msk
+  *             - \ref SC_INTSTS_RDAIF_Msk
+  * @return The status of specified interrupt.
+  * @retval 0 Specified interrupt does not happened.
+  * @retval 1 Specified interrupt happened.
+  * @details The macro is used to get receiver buffer time-out interrupt status, transfer error interrupt status,
+  *          transmit buffer empty interrupt status or receive data reach interrupt status.
+  * \hideinitializer
+  */
+#define SCUART_GET_INT_FLAG(sc, u32Type) ((sc)->INTSTS & (u32Type) ? 1 : 0)
+
+/**
+  * @brief Clear specified interrupt flag/status.
+  * @param[in] sc The pointer of smartcard module.
+  * @param[in] u32Type Interrupt flag/status to clear, could be the combination of following values:
+  *             - \ref SC_INTSTS_RBTOIF_Msk
+  *             - \ref SC_INTSTS_TERRIF_Msk
+  *             - \ref SC_INTSTS_TBEIF_Msk
+  * @return None
+  * @details The macro is used to clear receiver buffer time-out interrupt flag, transfer error interrupt flag or
+  *          transmit buffer empty interrupt flag.
+  * \hideinitializer
+  */
+#define SCUART_CLR_INT_FLAG(sc, u32Type) ((sc)->INTSTS = (u32Type))
+
+/**
+  * @brief Get receive error flag/status.
+  * @param[in] sc The pointer of smartcard module.
+  * @return Current receive error status, could one of following errors:
+  * @retval SC_STATUS_PEF_Msk Parity error.
+  * @retval SC_STATUS_FEF_Msk Frame error.
+  * @retval SC_STATUS_BEF_Msk Break error.
+  * @details The macro is used to get receiver parity error status, receiver frame error status or
+  *          receiver break error status.
+  * \hideinitializer
+  */
+#define SCUART_GET_ERR_FLAG(sc) ((sc)->STATUS & (SC_STATUS_PEF_Msk | SC_STATUS_FEF_Msk | SC_STATUS_BEF_Msk))
+
+/**
+  * @brief Clear specified receive error flag/status.
+  * @param[in] sc The pointer of smartcard module.
+  * @param[in] u32Mask Receive error flag/status to clear, combination following values:
+  *             - \ref SC_STATUS_PEF_Msk
+  *             - \ref SC_STATUS_FEF_Msk
+  *             - \ref SC_STATUS_BEF_Msk
+  * @return None
+  * @details The macro is used to clear receiver parity error flag, receiver frame error flag or
+  *          receiver break error flag.
+  * \hideinitializer
+  */
+#define SCUART_CLR_ERR_FLAG(sc, u32Mask) ((sc)->STATUS = (u32Mask))
+
+void SCUART_Close(SC_T* sc);
+uint32_t SCUART_Open(SC_T* sc, uint32_t u32baudrate);
+uint32_t SCUART_Read(SC_T* sc, uint8_t *pu8RxBuf, uint32_t u32ReadBytes);
+uint32_t SCUART_SetLineConfig(SC_T* sc, uint32_t u32Baudrate, uint32_t u32DataWidth, uint32_t u32Parity, uint32_t  u32StopBits);
+void SCUART_SetTimeoutCnt(SC_T* sc, uint32_t u32TOC);
+void SCUART_Write(SC_T* sc, uint8_t *pu8TxBuf, uint32_t u32WriteBytes);
+
+/*@}*/ /* end of group SCUART_EXPORTED_FUNCTIONS */
+
+/*@}*/ /* end of group SCUART_Driver */
+
+/*@}*/ /* end of group Standard_Driver */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif //__SCUART_H__
+
+/*** (C) COPYRIGHT 2013~2015 Nuvoton Technology Corp. ***/