Diff: cmsis/BUILD/mbed/hal/rtc_api.h

Revision:

189:f392fc9709a3

diff -r bcfe06ba3d64 -r f392fc9709a3 cmsis/BUILD/mbed/hal/rtc_api.h
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/cmsis/BUILD/mbed/hal/rtc_api.h	Wed Feb 20 22:31:08 2019 +0000
@@ -0,0 +1,188 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2006-2013 ARM Limited
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+/** \addtogroup hal */
+/** @{*/
+
+#ifndef MBED_RTC_API_H
+#define MBED_RTC_API_H
+
+#include "device.h"
+
+#include <time.h>
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/**
+ * \defgroup hal_rtc RTC hal
+ *
+ * The RTC hal provides a low level interface to the Real Time Counter (RTC) of a
+ * target.
+ *
+ * # Defined behaviour
+ * * The function ::rtc_init is safe to call repeatedly - Verified by test ::rtc_init_test.
+ * * RTC accuracy is at least 10% - Verified by test ::rtc_accuracy_test.
+ * * Init/free doesn't stop RTC from counting - Verified by test ::rtc_persist_test.
+ * * Software reset doesn't stop RTC from counting - Verified by test ::rtc_reset_test.
+ * * Sleep modes don't stop RTC from counting - Verified by test ::rtc_sleep_test.
+ * * Shutdown mode doesn't stop RTC from counting - Not verified.
+ * * The functions ::rtc_write/::rtc_read provides availability to set/get RTC time
+ * - Verified by test ::rtc_write_read_test.
+ * * The functions ::rtc_isenabled returns 1 if the RTC is counting and the time has been set,
+ * 0 otherwise - Verified by test ::rtc_enabled_test.
+ *
+ * # Undefined behaviour
+ * * Calling any function other than ::rtc_init before the initialisation of the RTC
+ *
+ * # Potential bugs
+ * * Incorrect overflow handling - Verified by ::rtc_range_test
+ * * Glitches due to ripple counter - Verified by ::rtc_glitch_test
+ *
+ * @see hal_rtc_tests
+ *
+ * @{
+ */
+
+/**
+ * \defgroup hal_rtc_tests RTC hal tests
+ * The RTC test validate proper implementation of the RTC hal.
+ *
+ * To run the RTC hal tests use the command:
+ *
+ *     mbed test -t <toolchain> -m <target> -n tests-mbed_hal-rtc*
+ */
+
+
+/** Initialize the RTC peripheral
+ *
+ * Powerup the RTC in perpetration for access. This function must be called
+ * before any other RTC functions ares called. This does not change the state
+ * of the RTC. It just enables access to it.
+ *
+ * @note This function is safe to call repeatedly - Tested by ::rtc_init_test
+ *
+ * Example Implementation Pseudo Code:
+ * @code
+ * void rtc_init()
+ * {
+ *     // Enable clock gate so processor can read RTC registers
+ *     POWER_CTRL |= POWER_CTRL_RTC_Msk;
+ *
+ *     // See if the RTC is already setup
+ *     if (!(RTC_STATUS & RTC_STATUS_COUNTING_Msk)) {
+ *
+ *         // Setup the RTC clock source
+ *         RTC_CTRL |= RTC_CTRL_CLK32_Msk;
+ *     }
+ * }
+ * @endcode
+ */
+void rtc_init(void);
+
+/** Deinitialize RTC
+ *
+ * Powerdown the RTC in preparation for sleep, powerdown or reset. That should only
+ * affect the CPU domain and not the time keeping logic.
+ * After this function is called no other RTC functions should be called
+ * except for ::rtc_init.
+ *
+ * @note This function does not stop the RTC from counting - Tested by ::rtc_persist_test
+ *
+ * Example Implementation Pseudo Code:
+ * @code
+ * void rtc_free()
+ * {
+ *     // Disable clock gate since processor no longer needs to read RTC registers
+ *     POWER_CTRL &= ~POWER_CTRL_RTC_Msk;
+ * }
+ * @endcode
+ */
+void rtc_free(void);
+
+/** Check if the RTC has the time set and is counting
+ *
+ * @retval 0 The time reported by the RTC is not valid
+ * @retval 1 The time has been set the RTC is counting
+ *
+ * Example Implementation Pseudo Code:
+ * @code
+ * int rtc_isenabled()
+ * {
+ *     if (RTC_STATUS & RTC_STATUS_COUNTING_Msk) {
+ *         return 1;
+ *     } else {
+ *         return 0;
+ *     }
+ * }
+ * @endcode
+ */
+int rtc_isenabled(void);
+
+/** Get the current time from the RTC peripheral
+ *
+ * @return The current time in seconds
+ *
+ * @note Some RTCs are not synchronized with the main clock. If
+ * this is the case with your RTC then you must read the RTC time
+ * in a loop to prevent reading the wrong time due to a glitch.
+ * The test ::rtc_glitch_test is intended to catch this bug.
+ *
+ * Example implementation for an unsynchronized ripple counter:
+ * @code
+ * time_t rtc_read()
+ * {
+ *     uint32_t val;
+ *     uint32_t last_val;
+ *
+ *     // Loop until the same value is read twice
+ *     val = RTC_SECONDS;
+ *     do {
+ *         last_val = val;
+ *         val = RTC_SECONDS;
+ *     } while (last_val != val);
+ *
+ *     return (time_t)val;
+ * }
+ * @endcode
+ */
+time_t rtc_read(void);
+
+/** Write the current time in seconds to the RTC peripheral
+ *
+ * @param t The current time to be set in seconds.
+ *
+ * Example Implementation Pseudo Code:
+ * @code
+ * void rtc_write(time_t t)
+ * {
+ *     RTC_SECONDS = t;
+ * }
+ * @endcode
+ */
+void rtc_write(time_t t);
+
+/**@}*/
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
+
+/** @}*/