mbed library sources
Fork of mbed-src by
targets/hal/TARGET_Atmel/TARGET_SAM21/drivers/sercom/i2c/quick_start_master/qs_i2c_master_basic_use.h
- Committer:
- mbed_official
- Date:
- 2015-07-17
- Revision:
- 592:a274ee790e56
- Parent:
- 579:53297373a894
File content as of revision 592:a274ee790e56:
/** * \page asfdoc_sam0_sercom_i2c_master_basic_use_case Quick Start Guide for SERCOM I2C Master - Basic * * In this use case, the I<SUP>2</SUP>C will used and set up as follows: * - Master mode * - 100KHz operation speed * - Not operational in standby * - 10000 packet timeout value * - 65535 unknown bus state timeout value * * * \section asfdoc_sam0_sercom_i2c_master_basic_use_case_prereq Prerequisites * The device must be connected to an I<SUP>2</SUP>C slave. * * \section asfdoc_sam0_sercom_i2c_master_basic_use_setup Setup * * \subsection asfdoc_sam0_sercom_i2c_master_basic_use_setup_code Code * The following must be added to the user application: * * - A sample buffer to send, a sample buffer to read: * \snippet qs_i2c_master_basic_use.c packet_data * * - Slave address to access: * \snippet qs_i2c_master_basic_use.c address * * - Number of times to try to send packet if it fails: * \snippet qs_i2c_master_basic_use.c timeout * * - Globally accessible module structure: * \snippet qs_i2c_master_basic_use.c dev_inst * * - Function for setting up the module: * \snippet qs_i2c_master_basic_use.c initialize_i2c * * - Add to user application \c main(): * \snippet qs_i2c_master_basic_use.c init * * \subsection asfdoc_sam0_sercom_i2c_master_basic_use_setup_workflow Workflow * -# Configure and enable module. * \snippet qs_i2c_master_basic_use.c initialize_i2c * -# Create and initialize configuration structure. * \snippet qs_i2c_master_basic_use.c init_conf * -# Change settings in the configuration. * \snippet qs_i2c_master_basic_use.c conf_change * -# Initialize the module with the set configurations. * \snippet qs_i2c_master_basic_use.c init_module * -# Enable the module. * \snippet qs_i2c_master_basic_use.c enable_module * -# Create a variable to see when we should stop trying to send packet. * \snippet qs_i2c_master_basic_use.c timeout_counter * -# Create a packet to send. * \snippet qs_i2c_master_basic_use.c packet * * \section asfdoc_sam0_sercom_i2c_master_basic_use_implemenation Implementation * \subsection asfdoc_sam0_sercom_i2c_master_basic_use_implemenation_code Code * Add to user application \c main(): * \snippet qs_i2c_master_basic_use.c main * * \subsection asfdoc_sam0_sercom_i2c_master_basic_use_implemenation_workflow Workflow * -# Write packet to slave. * \snippet qs_i2c_master_basic_use.c write_packet * The module will try to send the packet TIMEOUT number of times or until it is * successfully sent. * -# Read packet from slave. * \snippet qs_i2c_master_basic_use.c read_packet * The module will try to read the packet TIMEOUT number of times or until it is * successfully read. */ /** * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a> */ #include <asf.h> #include <conf_clocks.h>