![](/media/cache/img/default_profile.jpg.50x50_q85.jpg)
v
Dependencies: mbed SeeedShieldBot BluetoothSerial
main.cpp
- Committer:
- m1kl
- Date:
- 2021-11-28
- Revision:
- 0:4da4b81151c6
File content as of revision 0:4da4b81151c6:
#include "mbed.h" #include "BluetoothSerial.h" #include "SeeedStudioShieldBot.h" // The following configuration must be done on the NUCLEO board: // - Close SB62/SB63 and open SB13/SB14 solder bridges to enable the D0/D1 pins // - Open SB21 solder bridge to disconnect the LED BluetoothSerial bluetooth(D1, D0); // TX, RX #ifdef TARGET_NUCLEO_L053R8 #define PWM1 D6 // Connect D6 and D8 #define PWM2 D12 #else // NUCLEO_F072RB #define PWM1 D8 #define PWM2 D12 #endif SeeedStudioShieldBot bot( PWM1, D9, D11, // Right motor pins (PwmOut, DigitalOut, DigitalOut) -> Motor 1 PWM2, D10, D13, // Left motor pins (PwmOut, DigitalOut, DigitalOut) -> Motor 2 A0, A1, A2, A3, A4 // Sensors pins (all DigitalIn) ); // Disable the feature by wiring A5 to GND DigitalIn ReadSensorsEnabled(A5, PullUp); // Enable it for debugging on hyperterminal #define DEBUG 0 #if DEBUG == 1 Serial pc(PC_10, PC_11); // Connect PC10 and CN3-RX #define PC_DEBUG(args...) pc.printf(args) #else #define PC_DEBUG(args...) #endif Ticker tick; float speed = 1.0; // Used to select the motors speed int stop = 0; // Used to stop the motors when a sensor detects something void ReadCommand(void) { int cmd = 0; PC_DEBUG(">>> Read command...\n"); if (bluetooth.readable()) { cmd = bluetooth.getc(); PC_DEBUG(">>> Bluetooth read [%c]\n", cmd); // Ignore the receive command (excepted "Backward") if a sensor has detected something. if ((stop) && (cmd != '2')) return; switch (cmd) { case '1': // Forward bot.forward(speed); break; case '2': // Backward bot.backward(speed); break; case '3': // Left bot.left(speed); break; case '4': // Right bot.right(speed); break; case '5': // Turn left forward bot.turn_right(speed); break; case '6': // Turn right forward bot.turn_left(speed); break; case '7': // Turn left backward bot.turn_right(-speed); break; case '8': // Turn right backward bot.turn_left(-speed); break; case '9': // Slow speed = 0.5; break; case 'A': // Fast speed = 1.0; break; default: // Stop bot.stopAll(); break; } } } int main() { PC_DEBUG("\n\nSeeed Bluetooth shield test started.\n"); // Enable motors bot.enable_right_motor(); bot.enable_left_motor(); PC_DEBUG(">>> Bluetooth setup..."); bluetooth.setup(); PC_DEBUG("done\n"); PC_DEBUG(">>> Bluetooth in slave mode..."); bluetooth.slave("bt_seeed_1"); // default PIN code: 0000 PC_DEBUG("done\n"); wait(2); PC_DEBUG(">>> Bluetooth connect..."); bluetooth.connect(); PC_DEBUG("done\n"); tick.attach(ReadCommand, 0.3); // Every 300 ms read Bluetooth command // Check if motors are alive bot.left(speed); wait(0.2); bot.right(speed); wait(0.2); bot.stopAll(); while (1) { // Stop the motors if a sensor has detected something. if ((!bot.rightSensor || !bot.inRightSensor || !bot.centreSensor || !bot.inLeftSensor || !bot.leftSensor) && ReadSensorsEnabled) { if (!stop) bot.stopAll(); stop = 1; } else { stop = 0; } } }