Initial commit
Diff: mbed-dev-master/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F405RG/device/system_clock.c
- Revision:
- 0:bb348c97df44
diff -r 000000000000 -r bb348c97df44 mbed-dev-master/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F405RG/device/system_clock.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/mbed-dev-master/targets/TARGET_STM/TARGET_STM32F4/TARGET_MTS_MDOT_F405RG/device/system_clock.c Wed Sep 16 01:11:49 2020 +0000 @@ -0,0 +1,105 @@ +/* mbed Microcontroller Library +* Copyright (c) 2006-2017 ARM Limited +* +* Licensed under the Apache License, Version 2.0 (the "License"); +* you may not use this file except in compliance with the License. +* You may obtain a copy of the License at +* +* http://www.apache.org/licenses/LICENSE-2.0 +* +* Unless required by applicable law or agreed to in writing, software +* distributed under the License is distributed on an "AS IS" BASIS, +* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +* See the License for the specific language governing permissions and +* limitations under the License. +*/ + +#include "stm32f4xx.h" + + +/** +/*!< Uncomment the following line if you need to relocate your vector Table in + Internal SRAM. */ +/* #define VECT_TAB_SRAM */ +#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field. + This value must be a multiple of 0x200. */ + +/** + * @brief Setup the microcontroller system + * Initialize the FPU setting, vector table location and External memory + * configuration. + * @param None + * @retval None + */ +void SystemInit(void) +{ + /* FPU settings ------------------------------------------------------------*/ +#if (__FPU_PRESENT == 1) && (__FPU_USED == 1) + SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */ +#endif + /* Reset the RCC clock configuration to the default reset state ------------*/ + /* Set HSION bit */ + RCC->CR |= (uint32_t)0x00000001; + + /* Reset CFGR register */ + RCC->CFGR = 0x00000000; + + /* Reset HSEON, CSSON and PLLON bits */ + RCC->CR &= (uint32_t)0xFEF6FFFF; + + /* Reset PLLCFGR register */ + RCC->PLLCFGR = 0x24003010; + + /* Reset HSEBYP bit */ + RCC->CR &= (uint32_t)0xFFFBFFFF; + + /* Disable all interrupts */ + RCC->CIR = 0x00000000; + +#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM) + SystemInit_ExtMemCtl(); +#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */ + + /* Configure the Vector Table location add offset address ------------------*/ +#ifdef VECT_TAB_SRAM + SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */ +#else + SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */ +#endif + +} + +/** + * @brief Configures the System clock source, PLL Multiplier and Divider factors, + * AHB/APBx prescalers and Flash settings + * @note This function should be called only once the RCC clock configuration + * is reset to the default reset state (done in SystemInit() function). + * @param None + * @retval None + */ +void SetSysClock(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + __HAL_RCC_PWR_CLK_ENABLE(); + + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2); + + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = 26; + RCC_OscInitStruct.PLL.PLLN = 192; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; + RCC_OscInitStruct.PLL.PLLQ = 4; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1); +}