Diff: main.cpp

Revision:

0:b5fb7b3adfe2

Child:

1:b0e6c82af2ef

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp	Sat Sep 28 04:32:20 2013 +0000
@@ -0,0 +1,90 @@
+// MBED driver for AD9850 digital synthesizer using hacked SPI interface
+// Liam Goudge Sept 2013
+
+#include "mbed.h"
+
+SPI device (p5,p6,p7); // MOSI, MISO (not used), SCLK
+DigitalOut CS(p8); // Use pin 8 as a fake Chip select
+DigitalOut ADReset(p15); // Pin 15 is reset line for AD9850
+
+Serial pc(USBTX, USBRX); // tx, rx for debug terminal
+
+int reverseBits (int source)
+{
+// Unfortunately need to invert bit order of the desired frequency setting since MBED only allows for MSB first from SPI. We need LSB first for AD9850
+    int mask=0;;
+    int i=0;
+    int target=0;
+    int bitTarget=0x80000000; // Hard-wired for 32-bit inversion
+
+    for (i=0;i<32;i++) { // ditto
+        mask=1<<i;   
+        bitTarget=1<<(31-i); // ditto
+
+        if (source & mask)
+            target=target | bitTarget;
+    } 
+    return target;
+}    
+     
+void writeSPI(int frq, int phase)
+{           
+// Send the 40-bit packet. MBED only allows max 16-bit packets so we send 40-bits as 16, 16, 8
+    device.format(16,0); // 16-bits per packet, mode 0 (CPOL=0 CPHA=0)
+    device.frequency(1000000); //SPI clock set to 1MHz
+
+    wait_ms(5);
+
+    // First do chip select. Need to use a GPIO to fake the chip select since MBED doesn't allow to set positive logic CS signal
+    CS=1; // assert chip select (a.k.a FQ_UD frequency update input to AD9850)
+    wait_ms(5);
+    CS=0;
+        
+    device.write(frq>>16); // Write upper 16-bits first starting with bit 31
+    device.write(frq); // Now lower 16 bits starting with bit 15
+    
+    device.format(8,0); // Need to reset to 8-bit data since MBED only allows max 16-bit packets. For 40-bits we do 16, 16, 8
+    device.write(phase); // This is phase and factory settings byte
+
+    // Now pulse FQ_UD again to signal the end of the packet
+    CS=0;
+    wait_ms(5);
+    CS=1;
+    wait_ms(5);
+    CS=0;
+}
+    
+
+int main()
+{
+    int targetFrq=0x147AE148; // This is desired sine wave frequency for the AD9850, here set to 10MHz
+    int increment=0x346DC6; // This is a 100KHz frequency increment
+
+    // Reset the AD9850. Active high logic. Minimum reset period 5 clock cycles (5/125MHz)
+    ADReset=0;
+    wait_ms(5);
+    ADReset=1;
+    wait_ms(5);
+    ADReset=0;
+    
+    while(1)
+    {
+    
+    while (targetFrq<0x28F5C28F) // 20MHz
+    {
+        writeSPI(reverseBits(targetFrq),0);
+        targetFrq=targetFrq+increment;
+        //wait_ms(100);
+        }
+        
+    while (targetFrq>0x147AE148) // 10MHz
+    {
+        writeSPI(reverseBits(targetFrq),0);
+        targetFrq=targetFrq-increment;
+        //wait_ms(100);
+        }  
+    
+    }      
+        
+        
+}
\ No newline at end of file