Diff: arch/lpc_emac_config.h

Revision:

4:d827a085afd9

Parent:

3:dd8b8f5b449a

Child:

5:698d868a5285

diff -r dd8b8f5b449a -r d827a085afd9 arch/lpc_emac_config.h
--- a/arch/lpc_emac_config.h	Mon Jul 23 11:52:41 2012 +0000
+++ b/arch/lpc_emac_config.h	Fri Mar 01 15:30:33 2013 +0000
@@ -21,17 +21,17 @@
 * notification. NXP Semiconductors also make no representation or
 * warranty that such application will be suitable for the specified
 * use without further testing or modification.
-**********************************************************************/
-
-#ifndef __LPC_EMAC_CONFIG_H
-#define __LPC_EMAC_CONFIG_H
+**********************************************************************/
+
+#ifndef __LPC_EMAC_CONFIG_H
+#define __LPC_EMAC_CONFIG_H
+
+#include "lwip/opt.h"
 
-#include "lwip/opt.h"
-
-#ifdef __cplusplus
-extern "C"
-{
-#endif
+#ifdef __cplusplus
+extern "C"
+{
+#endif
 
 /** @defgroup lwip_phy_config    LWIP PHY configuration
  * @ingroup lwip_phy
@@ -40,53 +40,53 @@
  * @{
  */
 
-/** \brief  The PHY address connected the to MII/RMII
- */
-#define LPC_PHYDEF_PHYADDR 1    /**< The PHY address on the PHY device. */
-
-/** \brief  Enable autonegotiation mode.
- *          If this is enabled, the PHY will attempt to auto-negotiate the
- *          best link mode if the PHY supports it. If this is not enabled,
- *          the PHY_USE_FULL_DUPLEX and PHY_USE_100MBS defines will be
- *          used to select the link mode. Note that auto-negotiation may
- *          take a few seconds to complete.
- */
-#define PHY_USE_AUTONEG 1 /**< Enables auto-negotiation mode. */
-
-/** \brief  Sets up the PHY interface to either full duplex operation or
- *          half duplex operation if PHY_USE_AUTONEG is not enabled.
- */
-#define PHY_USE_FULL_DUPLEX 1 /**< Sets duplex mode to full. */
-
-/** \brief  Sets up the PHY interface to either 100MBS operation or 10MBS
- *          operation if PHY_USE_AUTONEG is not enabled.
- */
-#define PHY_USE_100MBS 1 /**< Sets data rate to 100Mbps. */
+/** \brief  The PHY address connected the to MII/RMII
+ */
+#define LPC_PHYDEF_PHYADDR 1    /**< The PHY address on the PHY device. */
+
+/** \brief  Enable autonegotiation mode.
+ *          If this is enabled, the PHY will attempt to auto-negotiate the
+ *          best link mode if the PHY supports it. If this is not enabled,
+ *          the PHY_USE_FULL_DUPLEX and PHY_USE_100MBS defines will be
+ *          used to select the link mode. Note that auto-negotiation may
+ *          take a few seconds to complete.
+ */
+#define PHY_USE_AUTONEG 1 /**< Enables auto-negotiation mode. */
+
+/** \brief  Sets up the PHY interface to either full duplex operation or
+ *          half duplex operation if PHY_USE_AUTONEG is not enabled.
+ */
+#define PHY_USE_FULL_DUPLEX 1 /**< Sets duplex mode to full. */
+
+/** \brief  Sets up the PHY interface to either 100MBS operation or 10MBS
+ *          operation if PHY_USE_AUTONEG is not enabled.
+ */
+#define PHY_USE_100MBS 1 /**< Sets data rate to 100Mbps. */
 
 /**          
  * @}
- */
+ */
 
 /** @defgroup lwip_emac_config    LWIP EMAC configuration
  * @ingroup lwip_emac
  *
  * Configuration options for the LPC EMAC.
  * @{
- */
-
-/** \brief  Selects RMII or MII connection type in the EMAC peripheral
- */
-#define LPC_EMAC_RMII 1         /**< Use the RMII or MII driver variant .*/
+ */
 
-/** \brief  Defines the number of descriptors used for RX. This
- *          must be a minimum value of 2.
- */
-#define LPC_NUM_BUFF_RXDESCS 3
-
-/** \brief  Defines the number of descriptors used for TX. Must
- *          be a minimum value of 2.
- */
-#define LPC_NUM_BUFF_TXDESCS 3
+/** \brief  Selects RMII or MII connection type in the EMAC peripheral
+ */
+#define LPC_EMAC_RMII 1         /**< Use the RMII or MII driver variant .*/
+
+/** \brief  Defines the number of descriptors used for RX. This
+ *          must be a minimum value of 2.
+ */
+#define LPC_NUM_BUFF_RXDESCS 3
+
+/** \brief  Defines the number of descriptors used for TX. Must
+ *          be a minimum value of 2.
+ */
+#define LPC_NUM_BUFF_TXDESCS 3
 
 /** \brief  Set this define to 1 to enable bounce buffers for transmit pbufs
  *          that cannot be sent via the zero-copy method. Some chained pbufs
@@ -97,15 +97,15 @@
  *          buffer will be created and used instead.
  */
 #define LPC_TX_PBUF_BOUNCE_EN 1
-
+
 /**          
  * @}
- */
+ */
 
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __LPC_EMAC_CONFIG_H */
-
-/* --------------------------------- End Of File ------------------------------ */
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __LPC_EMAC_CONFIG_H */
+
+/* --------------------------------- End Of File ------------------------------ */