Diff: BME280_SPI/BME280_SPI.cpp

Revision:

0:a8bfd25ff975

diff -r 000000000000 -r a8bfd25ff975 BME280_SPI/BME280_SPI.cpp
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/BME280_SPI/BME280_SPI.cpp	Mon Feb 12 05:04:29 2018 +0000
@@ -0,0 +1,226 @@
+/**
+ ******************************************************************************
+ * @file    BME280_SPI.cpp
+ * @author  Toyomasa Watarai
+ * @version V1.0.0
+ * @date    11 March 2017
+ * @brief   BME280_SPI class implementation
+ ******************************************************************************
+ * @attention
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#include "mbed.h"
+#include "BME280_SPI.h"
+#include "SEGGER_RTT.h"
+
+BME280_SPI::BME280_SPI(PinName mosi, PinName miso, PinName sclk, PinName cs)
+    :
+    _spi(mosi, miso, sclk),
+    _cs(cs),
+    t_fine(0)
+{
+    initialize();
+}
+
+
+BME280_SPI::~BME280_SPI()
+{
+}
+
+void BME280_SPI::initialize()
+{
+    char cmd[18];
+
+    _cs = 1;
+    _spi.format(8, 0); // 8-bit, mode=0
+    _spi.frequency(1000000); // 1MHZ
+
+    _cs = 0;
+    _spi.write(0xd0); // chip_id
+    cmd[0] = _spi.write(0); // read chip_id
+    _cs = 1;
+    
+    DEBUG_PRINT("chip_id = 0x%x\n", cmd[0]);
+
+    _cs = 0;
+    _spi.write(0xf2 & BME280_SPI_MASK); // ctrl_hum
+    _spi.write(0x04); // Humidity oversampling x4
+    _cs = 1;
+
+    _cs = 0;
+    _spi.write(0xf4 & BME280_SPI_MASK); // ctrl_meas
+    _spi.write((4<<5)|(4<<2)|3); // Temparature oversampling x4, Pressure oversampling x4, Normal mode
+    _cs = 1;
+
+    _cs = 0;
+    _spi.write(0xf5 & BME280_SPI_MASK); // config
+    _spi.write(0xa0); // Standby 1000ms, Filter off, 4-wire SPI interface
+    _cs = 1;
+
+    wait(1);
+    
+    _cs = 0;
+    _spi.write(0x88); // read dig_T regs
+    for(int i = 0; i < 6; i++)
+        cmd[i] = _spi.write(0);
+    _cs = 1;
+
+    dig_T1 = (cmd[1] << 8) | cmd[0];
+    dig_T2 = (cmd[3] << 8) | cmd[2];
+    dig_T3 = (cmd[5] << 8) | cmd[4];
+
+    DEBUG_PRINT("dig_T = 0x%x, 0x%x, 0x%x\n", dig_T1, dig_T2, dig_T3);
+    DEBUG_PRINT("dig_T = %d, %d, %d\n", dig_T1, dig_T2, dig_T3);
+
+    _cs = 0;
+    _spi.write(0x8e); // read dig_P regs
+    for(int i = 0; i < 18; i++)
+        cmd[i] = _spi.write(0);
+    _cs = 1;
+
+    dig_P1 = (cmd[ 1] << 8) | cmd[ 0];
+    dig_P2 = (cmd[ 3] << 8) | cmd[ 2];
+    dig_P3 = (cmd[ 5] << 8) | cmd[ 4];
+    dig_P4 = (cmd[ 7] << 8) | cmd[ 6];
+    dig_P5 = (cmd[ 9] << 8) | cmd[ 8];
+    dig_P6 = (cmd[11] << 8) | cmd[10];
+    dig_P7 = (cmd[13] << 8) | cmd[12];
+    dig_P8 = (cmd[15] << 8) | cmd[14];
+    dig_P9 = (cmd[17] << 8) | cmd[16];
+
+    DEBUG_PRINT("dig_P = 0x%x, 0x%x, 0x%x, 0x%x, 0x%x, 0x%x, 0x%x, 0x%x, 0x%x\n", dig_P1, dig_P2, dig_P3, dig_P4, dig_P5, dig_P6, dig_P7, dig_P8, dig_P9);
+    DEBUG_PRINT("dig_P = %d, %d, %d, %d, %d, %d, %d, %d, %d\n", dig_P1, dig_P2, dig_P3, dig_P4, dig_P5, dig_P6, dig_P7, dig_P8, dig_P9);
+
+    _cs = 0;
+    _spi.write(0xA1); // read dig_H1 reg
+    cmd[0] = _spi.write(0);
+    _cs = 1;
+
+    _cs = 0;
+    _spi.write(0xE1); // read dig_H regs
+    for(int i = 0; i < 7; i++)
+        cmd[1+i] = _spi.write(0);
+    _cs = 1;
+
+    dig_H1 = cmd[0];
+    dig_H2 = (cmd[2] << 8) | cmd[1];
+    dig_H3 = cmd[3];
+    dig_H4 = (cmd[4] << 4) | (cmd[5] & 0x0f);
+    dig_H5 = (cmd[6] << 4) | ((cmd[5]>>4) & 0x0f);
+    dig_H6 = cmd[7];
+
+    DEBUG_PRINT("dig_H = 0x%x, 0x%x, 0x%x, 0x%x, 0x%x, 0x%x\n", dig_H1, dig_H2, dig_H3, dig_H4, dig_H5, dig_H6);
+    DEBUG_PRINT("dig_H = %d, %d, %d, %d, %d, %d\n", dig_H1, dig_H2, dig_H3, dig_H4, dig_H5, dig_H6);
+}
+
+float BME280_SPI::getTemperature()
+{
+    uint32_t temp_raw;
+    float tempf;
+    char cmd[3];
+
+    _cs = 0;
+    _spi.write(0xfa);
+    for(int i = 0; i < 3; i++)
+        cmd[i] = _spi.write(0);
+    _cs = 1;
+
+    temp_raw = (cmd[0] << 12) | (cmd[1] << 4) | (cmd[2] >> 4);
+
+    int32_t temp;
+
+    temp =
+        (((((temp_raw >> 3) - (dig_T1 << 1))) * dig_T2) >> 11) +
+        ((((((temp_raw >> 4) - dig_T1) * ((temp_raw >> 4) - dig_T1)) >> 12) * dig_T3) >> 14);
+
+    t_fine = temp;
+    temp = (temp * 5 + 128) >> 8;
+    SEGGER_RTT_printf(0, "temp is %d", temp/100);
+    tempf = (float)temp;
+
+    return (tempf/100.0f);
+}
+
+float BME280_SPI::getPressure()
+{
+    uint32_t press_raw;
+    float pressf;
+    char cmd[3];
+
+    _cs = 0;
+    _spi.write(0xf7); // press_msb
+    for(int i = 0; i < 3; i++)
+        cmd[i] = _spi.write(0);
+    _cs = 1;
+
+    press_raw = (cmd[0] << 12) | (cmd[1] << 4) | (cmd[2] >> 4);
+
+    int32_t var1, var2;
+    uint32_t press;
+
+    var1 = (t_fine >> 1) - 64000;
+    var2 = (((var1 >> 2) * (var1 >> 2)) >> 11) * dig_P6;
+    var2 = var2 + ((var1 * dig_P5) << 1);
+    var2 = (var2 >> 2) + (dig_P4 << 16);
+    var1 = (((dig_P3 * (((var1 >> 2)*(var1 >> 2)) >> 13)) >> 3) + ((dig_P2 * var1) >> 1)) >> 18;
+    var1 = ((32768 + var1) * dig_P1) >> 15;
+    if (var1 == 0) {
+        return 0;
+    }
+    press = (((1048576 - press_raw) - (var2 >> 12))) * 3125;
+    if(press < 0x80000000) {
+        press = (press << 1) / var1;
+    } else {
+        press = (press / var1) * 2;
+    }
+    var1 = ((int32_t)dig_P9 * ((int32_t)(((press >> 3) * (press >> 3)) >> 13))) >> 12;
+    var2 = (((int32_t)(press >> 2)) * (int32_t)dig_P8) >> 13;
+    press = (press + ((var1 + var2 + dig_P7) >> 4));
+    SEGGER_RTT_printf(0, "pressure is %d", press/100);
+    
+    pressf = (float)press;
+    return (pressf/100.0f);
+}
+
+float BME280_SPI::getHumidity()
+{
+    uint32_t hum_raw;
+    float humf;
+    char cmd[2];
+
+    _cs = 0;
+    _spi.write(0xfd); // hum_msb
+    for(int i = 0; i < 2; i++)
+        cmd[i] = _spi.write(0);
+    _cs = 1;
+
+    hum_raw = (cmd[0] << 8) | cmd[1];
+
+    int32_t v_x1;
+
+    v_x1 = t_fine - 76800;
+    v_x1 =  (((((hum_raw << 14) -(((int32_t)dig_H4) << 20) - (((int32_t)dig_H5) * v_x1)) +
+               ((int32_t)16384)) >> 15) * (((((((v_x1 * (int32_t)dig_H6) >> 10) *
+                                            (((v_x1 * ((int32_t)dig_H3)) >> 11) + 32768)) >> 10) + 2097152) *
+                                            (int32_t)dig_H2 + 8192) >> 14));
+    v_x1 = (v_x1 - (((((v_x1 >> 15) * (v_x1 >> 15)) >> 7) * (int32_t)dig_H1) >> 4));
+    v_x1 = (v_x1 < 0 ? 0 : v_x1);
+    v_x1 = (v_x1 > 419430400 ? 419430400 : v_x1);
+    SEGGER_RTT_printf(0, "humidity is %d", (v_x1 >> 12)/1024);
+    
+    humf = (float)(v_x1 >> 12);
+
+    return (humf/1024.0f);
+}