Diff: sensor.h

Revision:

5:8a3cf73d7ed3

Parent:

4:e5018e5ba340

--- a/sensor.h	Thu Jun 16 08:12:33 2016 +0000
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,111 +0,0 @@
-#include "MicroduinoPinNames.h"
-#include "Config.h"
-#include "AM2321.h"
-
-extern Serial pc;
-#define INTERVAL_pm25    200
-
-//SoftwareSerial pmSerial(4,5);   //PM2.5传感器通讯软串口
-#ifdef OPEN_PM25
-Serial pmSerial(D5, D4); //tx,rx
-#endif
-AnalogIn gLight(A0);
-AnalogIn gCH4(A2);
-AM2321 am2321;
-
-float sensor_tem,sensor_hum,sensor_light,Sensor_etoh;
-
-float sensorPM25 = 6.6;
-
-long map(long x, long in_min, long in_max, long out_min, long out_max)
-{
-    return (x - in_min) * (out_max - out_min) / (in_max - in_min) + out_min;
-}
-
-#ifdef OPEN_PM25
-void PM25_init(void)
-{
-    //pc.printf("Enter PM25_init\r\n");
-    pmSerial.baud(2400);
-}
-
-// 读取PM2.5传感器
-void PM25()
-{
-    //pc.printf("Enter PM25()\r\n");
-    int data_s = 0;    //串口接收数据
-    int num = -1;      //串口接收数据计数
-    int sum = 0;       //校验和
-    int cal[6];        //接收数据缓存
-    float dustDensity = 0;  //PM2.5浓度
-
-    //pmSerial.begin(2400);   //首先启动软串口
-    //pmSerial.baud(2400);
-    //pmSerial.flush();       //清空串口缓存
-
-    while(1) {
-        //pc.printf("PM25:while(1)\r\n");
-        //if(pmSerial.available() > 0) { //串口缓存有数据
-        if (pmSerial.readable() > 0) {
-        //if ((data_s = pmSerial.getc()) != 0) {
-            //myled = 0;
-            //pc.printf("readable() > 0\r\n");
-            //data_s = pmSerial.read();   //读取串口缓存数据
-            data_s = pmSerial.getc();
-            if(data_s == 0xAA) {         //得到数据帧起始位
-                num = 0;                  //开始计数
-            } else if(num >= 0) {
-                num++;                //读到数据，计数+1
-                cal[num-1] = data_s;  //数据保存到缓存中
-                if(num == 6) {         //读到数据帧最后一位
-                    sum = cal[0] + cal[1] + cal[2] + cal[3];  //计算校验和
-                    if(sum == cal[4] && cal[5] == 0xFF) {     //校验和匹配，数据帧最后一位为0xFF，说明接收的数据帧正常
-                        dustDensity = (cal[0]*256 + cal[1])*(5.0/1024)*550;   //计算PM2.5浓度，单位ug/m3
-                    } else {   //接收的数据不正常
-                        dustDensity = 0;    //浓度清零
-                    }
-                    break;
-                }
-            }
-        }
-    }
-    //pmSerial.end();     //关闭软串口
-    //return dustDensity; //返回值
-    sensorPM25 = dustDensity;
-    //pc.printf("sensorPM25 = %f\r\n", sensorPM25);
-}
-#endif
-
-// 读取光照传感器
-void updateLight()
-{
-    //sensor_light = map(analogRead(A0), 0, 1023, 0, 255);
-    //float lvf = gLight;
-    uint16_t lt = gLight.read_u16();
-    //pc.printf("light = %d, lvf = %f\r\n", lt, lvf);
-    sensor_light = map(lt, 0, 65535, 0, 255);// 这里和Arduino不一样，不知道为什么
-}
-
-// 读取甲醛传感器
-void updateCH4()
-{
-    sensorPM25 += 1.0;
-    //Sensor_etoh = map(analogRead(A2), 0, 1023, 0, 30);
-    uint16_t ch4 = gCH4.read_u16();
-    Sensor_etoh = map(ch4, 0, 65535, 0, 30);
-    //pc.printf("CH4 = %d\r\n", ch4);
-}
-
-// 读取温湿度传感器
-void updateTempHumi()
-{
-    static uint32_t cot = 0;
-    cot++;
-    
-    #if 1
-    am2321.read();
-    sensor_tem = am2321.temperature / 10.0;
-    sensor_hum = am2321.humidity / 10.0;
-    #endif
-    //pc.printf("%u:temp = %.1f, hum = %.1f\r\n",cot, sensor_tem, sensor_hum);
-}