mbed library sources

Dependents:   Freedman_v2 Nucleo_i2c_OLED_BME280_copy

Fork of mbed-src by mbed official

targets/hal/TARGET_STM/TARGET_STM32F3/pinmap.c

Committer:
kaizen
Date:
2015-08-24
Revision:
614:d1b257119699
Parent:
508:4f5903e025e6

File content as of revision 614:d1b257119699:

/* mbed Microcontroller Library
 *******************************************************************************
 * Copyright (c) 2014, STMicroelectronics
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 *    this list of conditions and the following disclaimer.
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 * 3. Neither the name of STMicroelectronics nor the names of its contributors
 *    may be used to endorse or promote products derived from this software
 *    without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *******************************************************************************
 */
#include "mbed_assert.h"
#include "pinmap.h"
#include "PortNames.h"
#include "mbed_error.h"

// GPIO mode look-up table
// Warning: the elements order must be the same as the one defined in PinNames.h
static const uint32_t gpio_mode[13] = {
    GPIO_MODE_INPUT,              //  0 = STM_MODE_INPUT
    GPIO_MODE_OUTPUT_PP,          //  1 = STM_MODE_OUTPUT_PP
    GPIO_MODE_OUTPUT_OD,          //  2 = STM_MODE_OUTPUT_OD
    GPIO_MODE_AF_PP,              //  3 = STM_MODE_AF_PP
    GPIO_MODE_AF_OD,              //  4 = STM_MODE_AF_OD
    GPIO_MODE_ANALOG,             //  5 = STM_MODE_ANALOG
    GPIO_MODE_IT_RISING,          //  6 = STM_MODE_IT_RISING
    GPIO_MODE_IT_FALLING,         //  7 = STM_MODE_IT_FALLING
    GPIO_MODE_IT_RISING_FALLING,  //  8 = STM_MODE_IT_RISING_FALLING
    GPIO_MODE_EVT_RISING,         //  9 = STM_MODE_EVT_RISING
    GPIO_MODE_EVT_FALLING,        // 10 = STM_MODE_EVT_FALLING
    GPIO_MODE_EVT_RISING_FALLING, // 11 = STM_MODE_EVT_RISING_FALLING
    0x10000000                    // 12 = STM_MODE_IT_EVT_RESET (not in STM32Cube HAL)
};

// Enable GPIO clock and return GPIO base address
uint32_t Set_GPIO_Clock(uint32_t port_idx)
{
    uint32_t gpio_add = 0;
    switch (port_idx) {
        case PortA:
            gpio_add = GPIOA_BASE;
            __GPIOA_CLK_ENABLE();
            break;
        case PortB:
            gpio_add = GPIOB_BASE;
            __GPIOB_CLK_ENABLE();
            break;
        case PortC:
            gpio_add = GPIOC_BASE;
            __GPIOC_CLK_ENABLE();
            break;
        case PortD:
            gpio_add = GPIOD_BASE;
            __GPIOD_CLK_ENABLE();
            break;
#if defined(GPIOE_BASE)
        case PortE:
            gpio_add = GPIOE_BASE;
            __GPIOE_CLK_ENABLE();
            break;
#endif
        case PortF:
            gpio_add = GPIOF_BASE;
            __GPIOF_CLK_ENABLE();
            break;
        default:
            error("Pinmap error: wrong port number.");
            break;
    }
    return gpio_add;
}

/**
 * Configure pin (mode, speed, output type and pull-up/pull-down)
 */
void pin_function(PinName pin, int data)
{
    MBED_ASSERT(pin != (PinName)NC);
    // Get the pin informations
    uint32_t mode  = STM_PIN_MODE(data);
    uint32_t pupd  = STM_PIN_PUPD(data);
    uint32_t afnum = STM_PIN_AFNUM(data);

    uint32_t port_index = STM_PORT(pin);
    uint32_t pin_index  = STM_PIN(pin);

    // Enable GPIO clock
    uint32_t gpio_add = Set_GPIO_Clock(port_index);
    GPIO_TypeDef *gpio = (GPIO_TypeDef *)gpio_add;

    // Configure GPIO
    GPIO_InitTypeDef GPIO_InitStructure;
    GPIO_InitStructure.Pin       = (uint32_t)(1 << pin_index);
    GPIO_InitStructure.Mode      = gpio_mode[mode];
    GPIO_InitStructure.Pull      = pupd;
    GPIO_InitStructure.Speed     = GPIO_SPEED_HIGH;
    GPIO_InitStructure.Alternate = afnum;
    HAL_GPIO_Init(gpio, &GPIO_InitStructure);

    // [TODO] Disconnect JTAG-DP + SW-DP signals.
    // Warning: Need to reconnect under reset
    //if ((pin == PA_13) || (pin == PA_14)) {
    //
    //}
}

/**
 * Configure pin pull-up/pull-down
 */
void pin_mode(PinName pin, PinMode mode)
{
    MBED_ASSERT(pin != (PinName)NC);
    uint32_t port_index = STM_PORT(pin);
    uint32_t pin_index  = STM_PIN(pin);

    // Enable GPIO clock
    uint32_t gpio_add = Set_GPIO_Clock(port_index);
    GPIO_TypeDef *gpio = (GPIO_TypeDef *)gpio_add;

    // Configure pull-up/pull-down resistors
    uint32_t pupd = (uint32_t)mode;
    if (pupd > 2) {
        pupd = 0; // Open-drain = No pull-up/No pull-down
    }
    gpio->PUPDR &= (uint32_t)(~(GPIO_PUPDR_PUPDR0 << (pin_index * 2)));
    gpio->PUPDR |= (uint32_t)(pupd << (pin_index * 2));
}