Diff: mbed-os/targets/TARGET_NUVOTON/TARGET_NUC472/gpio_api.c

Revision:

0:8fdf9a60065b

diff -r 000000000000 -r 8fdf9a60065b mbed-os/targets/TARGET_NUVOTON/TARGET_NUC472/gpio_api.c
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-os/targets/TARGET_NUVOTON/TARGET_NUC472/gpio_api.c	Wed Oct 10 00:33:53 2018 +0000
@@ -0,0 +1,142 @@
+/* mbed Microcontroller Library
+ * Copyright (c) 2015-2016 Nuvoton
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ *     http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#include "gpio_api.h"
+#include "mbed_assert.h"
+#include "pinmap.h"
+#include "mbed_error.h"
+#include "PeripheralPins.h"
+
+uint32_t gpio_set(PinName pin)
+{
+    if (pin == (PinName) NC) {
+        return 0;
+    }
+    
+    uint32_t pin_index = NU_PINNAME_TO_PIN(pin);
+    
+#if 1
+    pin_function(pin, 0 << NU_MFP_POS(pin_index));
+#else
+    pinmap_pinout(pin, PinMap_GPIO);
+#endif
+
+    return (uint32_t)(1 << pin_index);    // Return the pin mask
+}
+
+int gpio_is_connected(const gpio_t *obj)
+{
+    return (obj->pin != (PinName) NC);
+}
+
+void gpio_init(gpio_t *obj, PinName pin)
+{
+    obj->pin = pin;
+    
+    if (obj->pin == (PinName) NC) {
+        return;
+    }
+
+    obj->mask = gpio_set(pin);
+    /* Default mode/direction */
+    obj->mode = PullUp;
+    obj->direction = PIN_INPUT;
+}
+
+void gpio_mode(gpio_t *obj, PinMode mode)
+{
+    if (obj->pin == (PinName) NC) {
+        return;
+    }
+
+    switch (mode) {
+        case PullNone:
+        case PullDown:
+        case PullUp:
+            /* H/W doesn't support separate configuration for input pull mode/direction.
+             * We translate to input-only/push-pull output I/O mode dependent on direction. */
+            obj->mode = (obj->direction == PIN_INPUT) ? InputOnly : PushPullOutput;
+            break;
+
+        case QuasiBidirectional:
+            /* With quasi-bidirectional I/O mode, before digital input function is performed,
+             * the corresponding bit in GPIOx_DOUT must be set to 1. */
+            obj->mode = QuasiBidirectional;
+            if (obj->direction == PIN_INPUT) {
+                gpio_write(obj, 1);
+            }
+            break;
+
+        case InputOnly:
+        case PushPullOutput:
+            /* We may meet contradictory I/O mode/direction configuration. Favor I/O mode
+             * in the gpio_mode call here. */
+            if (mode == InputOnly) {
+                obj->direction = PIN_INPUT;
+                obj->mode = InputOnly;
+            } else {
+                obj->direction = PIN_OUTPUT;
+                obj->mode = PushPullOutput;
+            }
+            break;
+
+        default:
+            /* Allow for configuring other I/O modes directly */
+            obj->mode = mode;
+            break;
+    }
+
+    pin_mode(obj->pin, obj->mode);
+}
+
+void gpio_dir(gpio_t *obj, PinDirection direction)
+{
+    if (obj->pin == (PinName) NC) {
+        return;
+    }
+
+    obj->direction = direction;
+
+    switch (obj->mode) {
+        case PullNone:
+        case PullDown:
+        case PullUp:
+            /* H/W doesn't support separate configuration for input pull mode/direction.
+             * We translate to input-only/push-pull output I/O mode dependent on direction. */
+            obj->mode = (obj->direction == PIN_INPUT) ? InputOnly : PushPullOutput;
+            break;
+            
+        case QuasiBidirectional:
+            /* With quasi-bidirectional I/O mode, before digital input function is performed,
+             * the corresponding bit in GPIOx_DOUT must be set to 1. */
+            if (obj->direction == PIN_INPUT) {
+                gpio_write(obj, 1);
+            }
+            break;
+
+        case InputOnly:
+        case PushPullOutput:
+            /* We may meet contradictory I/O mode/direction configuration. Favor direction
+             * in the gpio_dir call here. */
+            obj->mode = (obj->direction == PIN_INPUT) ? InputOnly : PushPullOutput;
+            break;
+
+        default:
+            break;
+    }
+
+    pin_mode(obj->pin, obj->mode);
+}