takashi kadono
Color Oled(SSD1331) connect to STMicroelectronics Nucleo-F466
mbed-os/targets/TARGET_NUVOTON/TARGET_M2351/device/Reg/qei_reg.h
- Committer:
- kadonotakashi
- Date:
- 2018-10-11
- Revision:
- 3:f3764f852aa8
- Parent:
- 0:8fdf9a60065b
File content as of revision 3:f3764f852aa8:
/**************************************************************************//**
* @file qei_reg.h
* @version V1.00
* @brief QEI register definition header file
*
* @copyright (C) 2017 Nuvoton Technology Corp. All rights reserved.
*****************************************************************************/
#ifndef __QEI_REG_H__
#define __QEI_REG_H__
/*---------------------- Quadrature Encoder Interface -------------------------*/
/**
@addtogroup QEI Quadrature Encoder Interface(QEI)
Memory Mapped Structure for QEI Controller
@{ */
typedef struct
{
/**
* @var QEI_T::CNT
* Offset: 0x00 QEI Counter Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[31:0] |CNT |Quadrature Encoder Interface Counter
* | | |A 32-bit up/down counter
* | | |When an effective phase pulse is detected, this counter is increased by one if the bit DIRF (QEI_STATUS[8]) is one or decreased by one if the bit DIRF is zero
* | | |This register performs an integrator which count value is proportional to the encoder position
* | | |The pulse counter may be initialized to a predetermined value by one of three events occurs:
* | | |1. Software is written if QEIEN (QEI_CTL[29]) = 0.
* | | |2. Compare-match event if QEIEN=1 and QEI is in compare-counting mode.
* | | |3. Index signal change if QEIEN=1 and IDXRLDEN (QEI_CTL[27])=1.
* @var QEI_T::CNTHOLD
* Offset: 0x04 QEI Counter Hold Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[31:0] |CNTHOLD |Quadrature Encoder Interface Counter Hold
* | | |When bit HOLDCNT (QEI_CTL[24]) goes from low to high, the CNT(QEI_CNT[31:0]) is copied into CNTHOLD (QEI_CNTHOLD[31:0]) register.
* @var QEI_T::CNTLATCH
* Offset: 0x08 QEI Counter Index Latch Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[31:0] |CNTLATCH |Quadrature Encoder Interface Counter Index Latch
* | | |When the IDXF (QEI_STATUS[0]) bit is set, the CNT(QEI_CNT[31:0]) is copied into CNTLATCH (QEI_CNTLATCH[31:0]) register.
* @var QEI_T::CNTCMP
* Offset: 0x0C QEI Counter Compare Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[31:0] |CNTCMP |Quadrature Encoder Interface Counter Compare
* | | |If the QEI controller is in the compare-counting mode CMPEN (QEI_CTL[28]) =1, when the value of CNT(QEI_CNT[31:0]) matches CNTCMP(QEI_CNTCMP[31:0]), CMPF will be set
* | | |This register is software writable.
* @var QEI_T::CNTMAX
* Offset: 0x14 QEI Pre-set Maximum Count Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[31:0] |CNTMAX |Quadrature Encoder Interface Preset Maximum Count
* | | |This register value determined by user stores the maximum value which may be the number of the QEI counter for the QEI controller compare-counting mode
* @var QEI_T::CTL
* Offset: 0x18 QEI Controller Control Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[2:0] |NFCLKSEL |Noise Filter Clock Pre-divide Selection
* | | |To determine the sampling frequency of the Noise Filter clock .
* | | |000 = QEI_CLK.
* | | |001 = QEI_CLK/2.
* | | |010 = QEI_CLK/4.
* | | |011 = QEI_CLK/16.
* | | |100 = QEI_CLK/32.
* | | |101 = QEI_CLK/64.
* |[3] |NFDIS |QEI Controller Input Noise Filter Disable Bit
* | | |0 = The noise filter of QEI controller Enabled.
* | | |1 = The noise filter of QEI controller Disabled.
* |[4] |CHAEN |QEA Input to QEI Controller Enable Bit
* | | |0 = QEA input to QEI Controller Disabled.
* | | |1 = QEA input to QEI Controller Enabled.
* |[5] |CHBEN |QEB Input to QEI Controller Enable Bit
* | | |0 = QEB input to QEI Controller Disabled.
* | | |1 = QEB input to QEI Controller Enabled.
* |[6] |IDXEN |IDX Input to QEI Controller Enable Bit
* | | |0 = IDX input to QEI Controller Disabled.
* | | |1 = IDX input to QEI Controller Enabled.
* |[9:8] |MODE |QEI Counting Mode Selection
* | | |There are four quadrature encoder pulse counter operation modes.
* | | |00 = X4 Free-counting Mode.
* | | |01 = X2 Free-counting Mode.
* | | |10 = X4 Compare-counting Mode.
* | | |11 = X2 Compare-counting Mode.
* |[12] |CHAINV |Inverse QEA Input Polarity
* | | |0 = Not inverse QEA input polarity.
* | | |1 = QEA input polarity is inverse to QEI controller.
* |[13] |CHBINV |Inverse QEB Input Polarity
* | | |0 = Not inverse QEB input polarity.
* | | |1 = QEB input polarity is inverse to QEI controller.
* |[14] |IDXINV |Inverse IDX Input Polarity
* | | |0 = Not inverse IDX input polarity.
* | | |1 = IDX input polarity is inverse to QEI controller.
* |[16] |OVUNIEN |OVUNF Trigger QEI Interrupt Enable Bit
* | | |0 = OVUNF can trigger QEI controller interrupt Disabled.
* | | |1 = OVUNF can trigger QEI controller interrupt Enabled.
* |[17] |DIRIEN |DIRCHGF Trigger QEI Interrupt Enable Bit
* | | |0 = DIRCHGF can trigger QEI controller interrupt Disabled.
* | | |1 = DIRCHGF can trigger QEI controller interrupt Enabled.
* |[18] |CMPIEN |CMPF Trigger QEI Interrupt Enable Bit
* | | |0 = CMPF can trigger QEI controller interrupt Disabled.
* | | |1 = CMPF can trigger QEI controller interrupt Enabled.
* |[19] |IDXIEN |IDXF Trigger QEI Interrupt Enable Bit
* | | |0 = The IDXF can trigger QEI interrupt Disabled.
* | | |1 = The IDXF can trigger QEI interrupt Enabled.
* |[20] |HOLDTMR0 |Hold QEI_CNT by Timer 0
* | | |0 = TIF (TIMER0_INTSTS[0]) has no effect on HOLDCNT.
* | | |1 = A rising edge of bit TIF(TIMER0_INTSTS[0]) in timer 0 sets HOLDCNT to 1.
* |[21] |HOLDTMR1 |Hold QEI_CNT by Timer 1
* | | |0 = TIF(TIMER1_INTSTS[0]) has no effect on HOLDCNT.
* | | |1 = A rising edge of bit TIF (TIMER1_INTSTS[0]) in timer 1 sets HOLDCNT to 1.
* |[22] |HOLDTMR2 |Hold QEI_CNT by Timer 2
* | | |0 = TIF(TIMER2_INTSTS[0]) has no effect on HOLDCNT.
* | | |1 = A rising edge of bit TIF(TIMER2_INTSTS[0]) in timer 2 sets HOLDCNT to 1.
* |[23] |HOLDTMR3 |Hold QEI_CNT by Timer 3
* | | |0 = TIF (TIMER3_INTSTS[0]) has no effect on HOLDCNT.
* | | |1 = A rising edge of bit TIF(TIMER3_INTSTS[0]) in timer 3 sets HOLDCNT to 1.
* |[24] |HOLDCNT |Hold QEI_CNT Control
* | | |When this bit is set from low to high, the CNT(QEI_CNT[31:0]) is copied into QEI_CNTHOLD
* | | |This bit may be set by writing 1 to it or Timer0~Timer3 interrupt flag TIF (TIMERx_INTSTS[0]).
* | | |0 = No operation.
* | | |1 = QEI_CNT content is captured and stored in QEI_CNTHOLD.
* | | |Note: This bit is automatically cleared after QEI_CNTHOLD holds QEI_CNT value.
* |[25] |IDXLATEN |Index Latch QEI_CNT Enable Bit
* | | |If this bit is set to high, the QEI_CNT content will be latched into QEI_CNTLATCH at every rising on signal CHX.
* | | |0 = The index signal latch QEI counter function Disabled.
* | | |1 = The index signal latch QEI counter function Enabled.
* |[27] |IDXRLDEN |Index Trigger QEI_CNT Reload Enable Bit
* | | |When this bit is high and a rising edge comes on signal CHX, the QEI_CNT will be reset to zero if the counter is in up-counting type (DIRF = 1); while the QEI_CNT will be reloaded with CNTMAX (QEI_CNTMAX[31:0]) content if the counter is in down-counting type (DIRF = 0).
* | | |0 = Reload function Disabled.
* | | |1 = QEI_CNT re-initialized by Index signal Enabled.
* |[28] |CMPEN |the Compare Function Enable Bit
* | | |The compare function in QEI controller is to compare the dynamic counting QEI_CNT with the compare register CNTCMP( QEI_CNTCMP[31:0]), if CNT(QEI_CNT[31:0]) reaches CNTCMP( QEI_CNTCMP[31:0]), the flag CMPF will be set.
* | | |0 = Compare function Disabled.
* | | |1 = Compare function Enabled.
* |[29] |QEIEN |Quadrature Encoder Interface Controller Enable Bit
* | | |0 = QEI controller function Disabled.
* | | |1 = QEI controller function Enabled.
* @var QEI_T::STATUS
* Offset: 0x2C QEI Controller Status Register
* ---------------------------------------------------------------------------------------------------
* |Bits |Field |Descriptions
* | :----: | :----: | :---- |
* |[0] |IDXF |IDX Detected Flag
* | | |When the QEI controller detects a rising edge on signal CHX it will set flag IDXF to high.
* | | |0 = No rising edge detected on signal CHX.
* | | |1 = A rising edge occurs on signal CHX.
* | | |Note: This bit is only cleared by writing 1 to it.
* |[1] |CMPF |Compare-match Flag
* | | |If the QEI compare function is enabled, the flag is set by hardware while QEI counter up or down counts and reach to the CNTCMP(QEI_CNTCMP[31:0]).
* | | |0 = QEI counter does not match with CNTCMP(QEI_CNTCMP[31:0]).
* | | |1 = QEI counter counts to the same as CNTCMP(QEI_CNTCMP[31:0]).
* | | |Note: This bit is only cleared by writing 1 to it.
* |[2] |OVUNF |QEI Counter Overflow or Underflow Flag
* | | |Flag is set by hardware while QEI_CNT overflows from 0xFFFF_FFFF to zero in free-counting mode or from the CNTMAX (QEI_CNTMAX[31:0]) to zero in compare-counting mode
* | | |Similarly, the flag is set wile QEI counter underflow from zero to 0xFFFF_FFFF or CNTMAX (QEI_CNTMAX[31:0]).
* | | |0 = No overflow or underflow occurs in QEI counter.
* | | |1 = QEI counter occurs counting overflow or underflow.
* | | |Note: This bit is only cleared by writing 1 to it.
* |[3] |DIRCHGF |Direction Change Flag
* | | |Flag is set by hardware while QEI counter counting direction is changed
* | | |Software can clear this bit by writing 1 to it.
* | | |0 = No change in QEI counter counting direction.
* | | |1 = QEI counter counting direction is changed.
* | | |Note: This bit is only cleared by writing 1 to it.
* |[8] |DIRF |QEI Counter Counting Direction Indication
* | | |0 = QEI Counter is in down-counting.
* | | |1 = QEI Counter is in up-counting.
* | | |Note: This bit is set/reset by hardware according to the phase detection between CHA and CHB.
*/
__IO uint32_t CNT; /*!< [0x0000] QEI Counter Register */
__IO uint32_t CNTHOLD; /*!< [0x0004] QEI Counter Hold Register */
__IO uint32_t CNTLATCH; /*!< [0x0008] QEI Counter Index Latch Register */
__IO uint32_t CNTCMP; /*!< [0x000c] QEI Counter Compare Register */
__I uint32_t RESERVE0[1];
__IO uint32_t CNTMAX; /*!< [0x0014] QEI Pre-set Maximum Count Register */
__IO uint32_t CTL; /*!< [0x0018] QEI Controller Control Register */
__I uint32_t RESERVE1[4];
__IO uint32_t STATUS; /*!< [0x002c] QEI Controller Status Register */
} QEI_T;
/**
@addtogroup QEI_CONST QEI Bit Field Definition
Constant Definitions for QEI Controller
@{ */
#define QEI_CNT_CNT_Pos (0) /*!< QEI_T::CNT: CNT Position */
#define QEI_CNT_CNT_Msk (0xfffffffful << QEI_CNT_CNT_Pos) /*!< QEI_T::CNT: CNT Mask */
#define QEI_CNTHOLD_CNTHOLD_Pos (0) /*!< QEI_T::CNTHOLD: CNTHOLD Position */
#define QEI_CNTHOLD_CNTHOLD_Msk (0xfffffffful << QEI_CNTHOLD_CNTHOLD_Pos) /*!< QEI_T::CNTHOLD: CNTHOLD Mask */
#define QEI_CNTLATCH_CNTLATCH_Pos (0) /*!< QEI_T::CNTLATCH: CNTLATCH Position */
#define QEI_CNTLATCH_CNTLATCH_Msk (0xfffffffful << QEI_CNTLATCH_CNTLATCH_Pos) /*!< QEI_T::CNTLATCH: CNTLATCH Mask */
#define QEI_CNTCMP_CNTCMP_Pos (0) /*!< QEI_T::CNTCMP: CNTCMP Position */
#define QEI_CNTCMP_CNTCMP_Msk (0xfffffffful << QEI_CNTCMP_CNTCMP_Pos) /*!< QEI_T::CNTCMP: CNTCMP Mask */
#define QEI_CNTMAX_CNTMAX_Pos (0) /*!< QEI_T::CNTMAX: CNTMAX Position */
#define QEI_CNTMAX_CNTMAX_Msk (0xfffffffful << QEI_CNTMAX_CNTMAX_Pos) /*!< QEI_T::CNTMAX: CNTMAX Mask */
#define QEI_CTL_NFCLKSEL_Pos (0) /*!< QEI_T::CTL: NFCLKSEL Position */
#define QEI_CTL_NFCLKSEL_Msk (0x7ul << QEI_CTL_NFCLKSEL_Pos) /*!< QEI_T::CTL: NFCLKSEL Mask */
#define QEI_CTL_NFDIS_Pos (3) /*!< QEI_T::CTL: NFDIS Position */
#define QEI_CTL_NFDIS_Msk (0x1ul << QEI_CTL_NFDIS_Pos) /*!< QEI_T::CTL: NFDIS Mask */
#define QEI_CTL_CHAEN_Pos (4) /*!< QEI_T::CTL: CHAEN Position */
#define QEI_CTL_CHAEN_Msk (0x1ul << QEI_CTL_CHAEN_Pos) /*!< QEI_T::CTL: CHAEN Mask */
#define QEI_CTL_CHBEN_Pos (5) /*!< QEI_T::CTL: CHBEN Position */
#define QEI_CTL_CHBEN_Msk (0x1ul << QEI_CTL_CHBEN_Pos) /*!< QEI_T::CTL: CHBEN Mask */
#define QEI_CTL_IDXEN_Pos (6) /*!< QEI_T::CTL: IDXEN Position */
#define QEI_CTL_IDXEN_Msk (0x1ul << QEI_CTL_IDXEN_Pos) /*!< QEI_T::CTL: IDXEN Mask */
#define QEI_CTL_MODE_Pos (8) /*!< QEI_T::CTL: MODE Position */
#define QEI_CTL_MODE_Msk (0x3ul << QEI_CTL_MODE_Pos) /*!< QEI_T::CTL: MODE Mask */
#define QEI_CTL_CHAINV_Pos (12) /*!< QEI_T::CTL: CHAINV Position */
#define QEI_CTL_CHAINV_Msk (0x1ul << QEI_CTL_CHAINV_Pos) /*!< QEI_T::CTL: CHAINV Mask */
#define QEI_CTL_CHBINV_Pos (13) /*!< QEI_T::CTL: CHBINV Position */
#define QEI_CTL_CHBINV_Msk (0x1ul << QEI_CTL_CHBINV_Pos) /*!< QEI_T::CTL: CHBINV Mask */
#define QEI_CTL_IDXINV_Pos (14) /*!< QEI_T::CTL: IDXINV Position */
#define QEI_CTL_IDXINV_Msk (0x1ul << QEI_CTL_IDXINV_Pos) /*!< QEI_T::CTL: IDXINV Mask */
#define QEI_CTL_OVUNIEN_Pos (16) /*!< QEI_T::CTL: OVUNIEN Position */
#define QEI_CTL_OVUNIEN_Msk (0x1ul << QEI_CTL_OVUNIEN_Pos) /*!< QEI_T::CTL: OVUNIEN Mask */
#define QEI_CTL_DIRIEN_Pos (17) /*!< QEI_T::CTL: DIRIEN Position */
#define QEI_CTL_DIRIEN_Msk (0x1ul << QEI_CTL_DIRIEN_Pos) /*!< QEI_T::CTL: DIRIEN Mask */
#define QEI_CTL_CMPIEN_Pos (18) /*!< QEI_T::CTL: CMPIEN Position */
#define QEI_CTL_CMPIEN_Msk (0x1ul << QEI_CTL_CMPIEN_Pos) /*!< QEI_T::CTL: CMPIEN Mask */
#define QEI_CTL_IDXIEN_Pos (19) /*!< QEI_T::CTL: IDXIEN Position */
#define QEI_CTL_IDXIEN_Msk (0x1ul << QEI_CTL_IDXIEN_Pos) /*!< QEI_T::CTL: IDXIEN Mask */
#define QEI_CTL_HOLDTMR0_Pos (20) /*!< QEI_T::CTL: HOLDTMR0 Position */
#define QEI_CTL_HOLDTMR0_Msk (0x1ul << QEI_CTL_HOLDTMR0_Pos) /*!< QEI_T::CTL: HOLDTMR0 Mask */
#define QEI_CTL_HOLDTMR1_Pos (21) /*!< QEI_T::CTL: HOLDTMR1 Position */
#define QEI_CTL_HOLDTMR1_Msk (0x1ul << QEI_CTL_HOLDTMR1_Pos) /*!< QEI_T::CTL: HOLDTMR1 Mask */
#define QEI_CTL_HOLDTMR2_Pos (22) /*!< QEI_T::CTL: HOLDTMR2 Position */
#define QEI_CTL_HOLDTMR2_Msk (0x1ul << QEI_CTL_HOLDTMR2_Pos) /*!< QEI_T::CTL: HOLDTMR2 Mask */
#define QEI_CTL_HOLDTMR3_Pos (23) /*!< QEI_T::CTL: HOLDTMR3 Position */
#define QEI_CTL_HOLDTMR3_Msk (0x1ul << QEI_CTL_HOLDTMR3_Pos) /*!< QEI_T::CTL: HOLDTMR3 Mask */
#define QEI_CTL_HOLDCNT_Pos (24) /*!< QEI_T::CTL: HOLDCNT Position */
#define QEI_CTL_HOLDCNT_Msk (0x1ul << QEI_CTL_HOLDCNT_Pos) /*!< QEI_T::CTL: HOLDCNT Mask */
#define QEI_CTL_IDXLATEN_Pos (25) /*!< QEI_T::CTL: IDXLATEN Position */
#define QEI_CTL_IDXLATEN_Msk (0x1ul << QEI_CTL_IDXLATEN_Pos) /*!< QEI_T::CTL: IDXLATEN Mask */
#define QEI_CTL_IDXRLDEN_Pos (27) /*!< QEI_T::CTL: IDXRLDEN Position */
#define QEI_CTL_IDXRLDEN_Msk (0x1ul << QEI_CTL_IDXRLDEN_Pos) /*!< QEI_T::CTL: IDXRLDEN Mask */
#define QEI_CTL_CMPEN_Pos (28) /*!< QEI_T::CTL: CMPEN Position */
#define QEI_CTL_CMPEN_Msk (0x1ul << QEI_CTL_CMPEN_Pos) /*!< QEI_T::CTL: CMPEN Mask */
#define QEI_CTL_QEIEN_Pos (29) /*!< QEI_T::CTL: QEIEN Position */
#define QEI_CTL_QEIEN_Msk (0x1ul << QEI_CTL_QEIEN_Pos) /*!< QEI_T::CTL: QEIEN Mask */
#define QEI_STATUS_IDXF_Pos (0) /*!< QEI_T::STATUS: IDXF Position */
#define QEI_STATUS_IDXF_Msk (0x1ul << QEI_STATUS_IDXF_Pos) /*!< QEI_T::STATUS: IDXF Mask */
#define QEI_STATUS_CMPF_Pos (1) /*!< QEI_T::STATUS: CMPF Position */
#define QEI_STATUS_CMPF_Msk (0x1ul << QEI_STATUS_CMPF_Pos) /*!< QEI_T::STATUS: CMPF Mask */
#define QEI_STATUS_OVUNF_Pos (2) /*!< QEI_T::STATUS: OVUNF Position */
#define QEI_STATUS_OVUNF_Msk (0x1ul << QEI_STATUS_OVUNF_Pos) /*!< QEI_T::STATUS: OVUNF Mask */
#define QEI_STATUS_DIRCHGF_Pos (3) /*!< QEI_T::STATUS: DIRCHGF Position */
#define QEI_STATUS_DIRCHGF_Msk (0x1ul << QEI_STATUS_DIRCHGF_Pos) /*!< QEI_T::STATUS: DIRCHGF Mask */
#define QEI_STATUS_DIRF_Pos (8) /*!< QEI_T::STATUS: DIRF Position */
#define QEI_STATUS_DIRF_Msk (0x1ul << QEI_STATUS_DIRF_Pos) /*!< QEI_T::STATUS: DIRF Mask */
/**@}*/ /* QEI_CONST */
/**@}*/ /* end of QEI register group */
#endif /* __QEI_REG_H__ */