![](/media/cache/img/default_profile.jpg.50x50_q85.jpg)
Color Oled(SSD1331) connect to STMicroelectronics Nucleo-F466
mbed-os/targets/TARGET_NUVOTON/TARGET_M2351/device/Reg/otg_reg.h
- Committer:
- kadonotakashi
- Date:
- 2018-10-11
- Revision:
- 3:f3764f852aa8
- Parent:
- 0:8fdf9a60065b
File content as of revision 3:f3764f852aa8:
/**************************************************************************//** * @file otg_reg.h * @version V1.00 * @brief OTG register definition header file * * @copyright (C) 2017 Nuvoton Technology Corp. All rights reserved. *****************************************************************************/ #ifndef __OTG_REG_H__ #define __OTG_REG_H__ /*---------------------- USB On-The-Go Controller -------------------------*/ /** @addtogroup OTG USB On-The-Go Controller(OTG) Memory Mapped Structure for OTG Controller @{ */ typedef struct { /** * @var OTG_T::CTL * Offset: 0x00 OTG Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |VBUSDROP |Drop VBUS Control * | | |If user application running on this OTG A-device wants to conserve power, set this bit to drop VBUS * | | |BUSREQ (OTG_CTL[1]) will be also cleared no matter A-device or B-device. * | | |0 = Not drop the VBUS. * | | |1 = Drop the VBUS. * |[1] |BUSREQ |OTG Bus Request * | | |If OTG A-device wants to do data transfers via USB bus, setting this bit will drive VBUS high to detect USB device connection * | | |If user won't use the bus any more, clearing this bit will drop VBUS to save power * | | |This bit will be cleared when A-device goes to A_wait_vfall state * | | |This bit will be also cleared if VBUSDROP (OTG_CTL[0]) bit is set or IDSTS (OTG_STATUS[1]) changed. * | | |If user of an OTG-B Device wants to request VBUS, setting this bit will run SRP protocol * | | |This bit will be cleared if SRP failure (OTG A-device does not provide VBUS after B-device issues SRP in specified interval, defined in OTG specification) * | | |This bit will be also cleared if VBUSDROP (OTG_CTL[0]) bit is set or IDSTS (OTG_STATUS[1]) changed. * | | |0 = Not launch VBUS in OTG A-device or not request SRP in OTG B-device. * | | |1 = Launch VBUS in OTG A-device or request SRP in OTG B-device. * |[2] |HNPREQEN |OTG HNP Request Enable Bit * | | |When USB frame as A-device, set this bit when A-device allows to process HNP protocol -- A-device changes role from Host to Peripheral * | | |This bit will be cleared when OTG state changes from a_suspend to a_peripheral or goes back to a_idle state * | | |When USB frame as B-device, set this bit after the OTG A-device successfully sends a SetFeature (b_hnp_enable) command to the OTG B-device to start role change -- B-device changes role from Peripheral to Host * | | |This bit will be cleared when OTG state changes from b_peripheral to b_wait_acon or goes back to b_idle state. * | | |0 = HNP request Disabled. * | | |1 = HNP request Enabled (A-device can change role from Host to Peripheral or B-device can change role from Peripheral to Host). * | | |Note: Refer to OTG specification to get a_suspend, a_peripheral, a_idle and b_idle state. * |[4] |OTGEN |OTG Function Enable Bit * | | |User needs to set this bit to enable OTG function while USB frame configured as OTG device * | | |When USB frame not configured as OTG device, this bit is must be low. * | | |0= OTG function Disabled. * | | |1 = OTG function Enabled. * |[5] |WKEN |OTG ID Pin Wake-up Enable Bit * | | |0 = OTG ID pin status change wake-up function Disabled. * | | |1 = OTG ID pin status change wake-up function Enabled. * @var OTG_T::PHYCTL * Offset: 0x04 OTG PHY Control Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |OTGPHYEN |OTG PHY Enable Bit * | | |When USB frame is configured as OTG-device or ID-dependent, user needs to set this bit before using OTG function * | | |If device is not configured as OTG-device nor ID-dependent , this bit is "don't care". * | | |0 = OTG PHY Disabled. * | | |1 = OTG PHY Enabled. * |[1] |IDDETEN |ID Detection Enable Bit * | | |0 = Detect ID pin status Disabled. * | | |1 = Detect ID pin status Enabled. * |[4] |VBENPOL |Off-chip USB VBUS Power Switch Enable Polarity * | | |The OTG controller will enable off-chip USB VBUS power switch to provide VBUS power when need * | | |A USB_VBUS_EN pin is used to control the off-chip USB VBUS power switch. * | | |The polarity of enabling off-chip USB VBUS power switch (high active or low active) depends on the selected component * | | |Set this bit as following according to the polarity of off-chip USB VBUS power switch. * | | |0 = The off-chip USB VBUS power switch enable is active high. * | | |1 = The off-chip USB VBUS power switch enable is active low. * |[5] |VBSTSPOL |Off-chip USB VBUS Power Switch Status Polarity * | | |The polarity of off-chip USB VBUS power switch valid signal depends on the selected component * | | |A USB_VBUS_ST pin is used to monitor the valid signal of the off-chip USB VBUS power switch * | | |Set this bit as following according to the polarity of off-chip USB VBUS power switch. * | | |0 = The polarity of off-chip USB VBUS power switch valid status is high. * | | |1 = The polarity of off-chip USB VBUS power switch valid status is low. * @var OTG_T::INTEN * Offset: 0x08 OTG Interrupt Enable Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |ROLECHGIEN|Role (Host or Peripheral) Changed Interrupt Enable Bit * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * |[1] |VBEIEN |VBUS Error Interrupt Enable Bit * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * | | |Note: VBUS error means going to a_vbus_err state. Please refer to A-device state diagram in OTG specification. * |[2] |SRPFIEN |SRP Fail Interrupt Enable Bit * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * |[3] |HNPFIEN |HNP Fail Interrupt Enable Bit * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * |[4] |GOIDLEIEN |OTG Device Goes to IDLE State Interrupt Enable Bit * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * | | |Note: Going to idle state means going to a_idle or b_idle state * | | |Please refer to A-device state diagram and B-device state diagram in OTG spec. * |[5] |IDCHGIEN |IDSTS Changed Interrupt Enable Bit * | | |If this bit is set to 1 and IDSTS (OTG_STATUS[1]) status is changed from high to low or from low to high, an interrupt will be asserted. * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * |[6] |PDEVIEN |Act As Peripheral Interrupt Enable Bit * | | |If this bit is set to 1 and the device is changed as a peripheral, an interrupt will be asserted. * | | |0 = This device as a peripheral interrupt Disabled. * | | |1 = This device as a peripheral interrupt Enabled. * |[7] |HOSTIEN |Act As Host Interrupt Enable Bit * | | |If this bit is set to 1 and the device is changed as a host, an interrupt will be asserted. * | | |0 = This device as a host interrupt Disabled. * | | |1 = This device as a host interrupt Enabled. * |[8] |BVLDCHGIEN|B-device Session Valid Status Changed Interrupt Enable Bit * | | |If this bit is set to 1 and BVLD (OTG_STATUS[3]) status is changed from high to low or from low to high, an interrupt will be asserted. * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * |[9] |AVLDCHGIEN|A-device Session Valid Status Changed Interrupt Enable Bit * | | |If this bit is set to 1 and AVLD (OTG_STATUS[4]) status is changed from high to low or from low to high, an interrupt will be asserted. * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * |[10] |VBCHGIEN |VBUSVLD Status Changed Interrupt Enable Bit * | | |If this bit is set to 1 and VBUSVLD (OTG_STATUS[5]) status is changed from high to low or from low to high, an interrupt will be asserted. * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * |[11] |SECHGIEN |SESSEND Status Changed Interrupt Enable Bit * | | |If this bit is set to 1 and SESSEND (OTG_STATUS[2]) status is changed from high to low or from low to high, an interrupt will be asserted. * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * |[13] |SRPDETIEN |SRP Detected Interrupt Enable Bit * | | |0 = Interrupt Disabled. * | | |1 = Interrupt Enabled. * @var OTG_T::INTSTS * Offset: 0x0C OTG Interrupt Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |ROLECHGIF |OTG Role Change Interrupt Status * | | |This flag is set when the role of an OTG device changed from a host to a peripheral, or changed from a peripheral to a host while USB_ID pin status does not change. * | | |0 = OTG device role not changed. * | | |1 = OTG device role changed. * | | |Note: Write 1 to clear this flag. * |[1] |VBEIF |VBUS Error Interrupt Status * | | |This bit will be set when voltage on VBUS cannot reach a minimum valid threshold 4.4V within a maximum time of 100ms after OTG A-device starting to drive VBUS high. * | | |0 = OTG A-device drives VBUS over threshold voltage before this interval expires. * | | |1 = OTG A-device cannot drive VBUS over threshold voltage before this interval expires. * | | |Note: Write 1 to clear this flag and recover from the VBUS error state. * |[2] |SRPFIF |SRP Fail Interrupt Status * | | |After initiating SRP, an OTG B-device will wait for the OTG A-device to drive VBUS high at least TB_SRP_FAIL minimum, defined in OTG specification * | | |This flag is set when the OTG B-device does not get VBUS high after this interval. * | | |0 = OTG B-device gets VBUS high before this interval. * | | |1 = OTG B-device does not get VBUS high before this interval. * | | |Note: Write 1 to clear this flag. * |[3] |HNPFIF |HNP Fail Interrupt Status * | | |When A-device has granted B-device to be host and USB bus is in SE0 (both USB_D+ and USB_D- low) state, this bit will be set when A-device does not connect after specified interval expires. * | | |0 = A-device connects to B-device before specified interval expires. * | | |1 = A-device does not connect to B-device before specified interval expires. * | | |Note: Write 1 to clear this flag. * |[4] |GOIDLEIF |OTG Device Goes to IDLE Interrupt Status * | | |Flag is set if the OTG device transfers from non-idle state to idle state * | | |The OTG device will be neither a host nor a peripheral. * | | |0 = OTG device does not go back to idle state (a_idle or b_idle). * | | |1 = OTG device goes back to idle state(a_idle or b_idle). * | | |Note 1: Going to idle state means going to a_idle or b_idle state. Please refer to OTG specification. * | | |Note 2: Write 1 to clear this flag. * |[5] |IDCHGIF |ID State Change Interrupt Status * | | |0 = IDSTS (OTG_STATUS[1]) not toggled. * | | |1 = IDSTS (OTG_STATUS[1]) from high to low or from low to high. * | | |Note: Write 1 to clear this flag. * |[6] |PDEVIF |Act As Peripheral Interrupt Status * | | |0= This device does not act as a peripheral. * | | |1 = This device acts as a peripheral. * | | |Note: Write 1 to clear this flag. * |[7] |HOSTIF |Act As Host Interrupt Status * | | |0= This device does not act as a host. * | | |1 = This device acts as a host. * | | |Note: Write 1 to clear this flag. * |[8] |BVLDCHGIF |B-device Session Valid State Change Interrupt Status * | | |0 = BVLD (OTG_STATUS[3]) is not toggled. * | | |1 = BVLD (OTG_STATUS[3]) from high to low or low to high. * | | |Note: Write 1 to clear this status. * |[9] |AVLDCHGIF |A-device Session Valid State Change Interrupt Status * | | |0 = AVLD (OTG_STATUS[4]) not toggled. * | | |1 = AVLD (OTG_STATUS[4]) from high to low or low to high. * | | |Note: Write 1 to clear this status. * |[10] |VBCHGIF |VBUSVLD State Change Interrupt Status * | | |0 = VBUSVLD (OTG_STATUS[5]) not toggled. * | | |1 = VBUSVLD (OTG_STATUS[5]) from high to low or from low to high. * | | |Note: Write 1 to clear this status. * |[11] |SECHGIF |SESSEND State Change Interrupt Status * | | |0 = SESSEND (OTG_STATUS[2]) not toggled. * | | |1 = SESSEND (OTG_STATUS[2]) from high to low or from low to high. * | | |Note: Write 1 to clear this flag. * |[13] |SRPDETIF |SRP Detected Interrupt Status * | | |0 = SRP not detected. * | | |1 = SRP detected. * | | |Note: Write 1 to clear this status. * @var OTG_T::STATUS * Offset: 0x10 OTG Status Register * --------------------------------------------------------------------------------------------------- * |Bits |Field |Descriptions * | :----: | :----: | :---- | * |[0] |OVERCUR |Over Current Condition * | | |The voltage on VBUS cannot reach a minimum VBUS valid threshold, 4.4V minimum, within a maximum time of 100ms after OTG A-device drives VBUS high. * | | |0 = OTG A-device drives VBUS successfully. * | | |1 = OTG A-device cannot drives VBUS high in this interval. * |[1] |IDSTS |USB_ID Pin State of Mini-/Micro- Plug * | | |0 = Mini-A/Micro-A plug is attached. * | | |1 = Mini-B/Micro-B plug is attached. * |[2] |SESSEND |Session End Status * | | |When VBUS voltage is lower than 0.4V, this bit will be set to 1 * | | |Session end means no meaningful power on VBUS. * | | |0 = Session is not end. * | | |1 = Session is end. * |[3] |BVLD |B-device Session Valid Status * | | |0 = B-device session is not valid. * | | |1 = B-device session is valid. * |[4] |AVLD |A-device Session Valid Status * | | |0 = A-device session is not valid. * | | |1 = A-device session is valid. * |[5] |VBUSVLD |VBUS Valid Status * | | |When VBUS is larger than 4.7V, this bit will be set to 1. * | | |0 = VBUS is not valid. * | | |1 = VBUS is valid. * |[6] |ASPERI |As Peripheral Status * | | |When OTG as peripheral, this bit is set. * | | |0: OTG not as peripheral * | | |1: OTG as peripheral * |[7] |ASHOST |As Host Status * | | |When OTG as Host, this bit is set. * | | |0: OTG not as Host * | | |1: OTG as Host */ __IO uint32_t CTL; /*!< [0x0000] OTG Control Register */ __IO uint32_t PHYCTL; /*!< [0x0004] OTG PHY Control Register */ __IO uint32_t INTEN; /*!< [0x0008] OTG Interrupt Enable Register */ __IO uint32_t INTSTS; /*!< [0x000c] OTG Interrupt Status Register */ __I uint32_t STATUS; /*!< [0x0010] OTG Status Register */ } OTG_T; /** @addtogroup OTG_CONST OTG Bit Field Definition Constant Definitions for OTG Controller @{ */ #define OTG_CTL_VBUSDROP_Pos (0) /*!< OTG_T::CTL: VBUSDROP Position */ #define OTG_CTL_VBUSDROP_Msk (0x1ul << OTG_CTL_VBUSDROP_Pos) /*!< OTG_T::CTL: VBUSDROP Mask */ #define OTG_CTL_BUSREQ_Pos (1) /*!< OTG_T::CTL: BUSREQ Position */ #define OTG_CTL_BUSREQ_Msk (0x1ul << OTG_CTL_BUSREQ_Pos) /*!< OTG_T::CTL: BUSREQ Mask */ #define OTG_CTL_HNPREQEN_Pos (2) /*!< OTG_T::CTL: HNPREQEN Position */ #define OTG_CTL_HNPREQEN_Msk (0x1ul << OTG_CTL_HNPREQEN_Pos) /*!< OTG_T::CTL: HNPREQEN Mask */ #define OTG_CTL_OTGEN_Pos (4) /*!< OTG_T::CTL: OTGEN Position */ #define OTG_CTL_OTGEN_Msk (0x1ul << OTG_CTL_OTGEN_Pos) /*!< OTG_T::CTL: OTGEN Mask */ #define OTG_CTL_WKEN_Pos (5) /*!< OTG_T::CTL: WKEN Position */ #define OTG_CTL_WKEN_Msk (0x1ul << OTG_CTL_WKEN_Pos) /*!< OTG_T::CTL: WKEN Mask */ #define OTG_PHYCTL_OTGPHYEN_Pos (0) /*!< OTG_T::PHYCTL: OTGPHYEN Position */ #define OTG_PHYCTL_OTGPHYEN_Msk (0x1ul << OTG_PHYCTL_OTGPHYEN_Pos) /*!< OTG_T::PHYCTL: OTGPHYEN Mask */ #define OTG_PHYCTL_IDDETEN_Pos (1) /*!< OTG_T::PHYCTL: IDDETEN Position */ #define OTG_PHYCTL_IDDETEN_Msk (0x1ul << OTG_PHYCTL_IDDETEN_Pos) /*!< OTG_T::PHYCTL: IDDETEN Mask */ #define OTG_PHYCTL_VBENPOL_Pos (4) /*!< OTG_T::PHYCTL: VBENPOL Position */ #define OTG_PHYCTL_VBENPOL_Msk (0x1ul << OTG_PHYCTL_VBENPOL_Pos) /*!< OTG_T::PHYCTL: VBENPOL Mask */ #define OTG_PHYCTL_VBSTSPOL_Pos (5) /*!< OTG_T::PHYCTL: VBSTSPOL Position */ #define OTG_PHYCTL_VBSTSPOL_Msk (0x1ul << OTG_PHYCTL_VBSTSPOL_Pos) /*!< OTG_T::PHYCTL: VBSTSPOL Mask */ #define OTG_INTEN_ROLECHGIEN_Pos (0) /*!< OTG_T::INTEN: ROLECHGIEN Position */ #define OTG_INTEN_ROLECHGIEN_Msk (0x1ul << OTG_INTEN_ROLECHGIEN_Pos) /*!< OTG_T::INTEN: ROLECHGIEN Mask */ #define OTG_INTEN_VBEIEN_Pos (1) /*!< OTG_T::INTEN: VBEIEN Position */ #define OTG_INTEN_VBEIEN_Msk (0x1ul << OTG_INTEN_VBEIEN_Pos) /*!< OTG_T::INTEN: VBEIEN Mask */ #define OTG_INTEN_SRPFIEN_Pos (2) /*!< OTG_T::INTEN: SRPFIEN Position */ #define OTG_INTEN_SRPFIEN_Msk (0x1ul << OTG_INTEN_SRPFIEN_Pos) /*!< OTG_T::INTEN: SRPFIEN Mask */ #define OTG_INTEN_HNPFIEN_Pos (3) /*!< OTG_T::INTEN: HNPFIEN Position */ #define OTG_INTEN_HNPFIEN_Msk (0x1ul << OTG_INTEN_HNPFIEN_Pos) /*!< OTG_T::INTEN: HNPFIEN Mask */ #define OTG_INTEN_GOIDLEIEN_Pos (4) /*!< OTG_T::INTEN: GOIDLEIEN Position */ #define OTG_INTEN_GOIDLEIEN_Msk (0x1ul << OTG_INTEN_GOIDLEIEN_Pos) /*!< OTG_T::INTEN: GOIDLEIEN Mask */ #define OTG_INTEN_IDCHGIEN_Pos (5) /*!< OTG_T::INTEN: IDCHGIEN Position */ #define OTG_INTEN_IDCHGIEN_Msk (0x1ul << OTG_INTEN_IDCHGIEN_Pos) /*!< OTG_T::INTEN: IDCHGIEN Mask */ #define OTG_INTEN_PDEVIEN_Pos (6) /*!< OTG_T::INTEN: PDEVIEN Position */ #define OTG_INTEN_PDEVIEN_Msk (0x1ul << OTG_INTEN_PDEVIEN_Pos) /*!< OTG_T::INTEN: PDEVIEN Mask */ #define OTG_INTEN_HOSTIEN_Pos (7) /*!< OTG_T::INTEN: HOSTIEN Position */ #define OTG_INTEN_HOSTIEN_Msk (0x1ul << OTG_INTEN_HOSTIEN_Pos) /*!< OTG_T::INTEN: HOSTIEN Mask */ #define OTG_INTEN_BVLDCHGIEN_Pos (8) /*!< OTG_T::INTEN: BVLDCHGIEN Position */ #define OTG_INTEN_BVLDCHGIEN_Msk (0x1ul << OTG_INTEN_BVLDCHGIEN_Pos) /*!< OTG_T::INTEN: BVLDCHGIEN Mask */ #define OTG_INTEN_AVLDCHGIEN_Pos (9) /*!< OTG_T::INTEN: AVLDCHGIEN Position */ #define OTG_INTEN_AVLDCHGIEN_Msk (0x1ul << OTG_INTEN_AVLDCHGIEN_Pos) /*!< OTG_T::INTEN: AVLDCHGIEN Mask */ #define OTG_INTEN_VBCHGIEN_Pos (10) /*!< OTG_T::INTEN: VBCHGIEN Position */ #define OTG_INTEN_VBCHGIEN_Msk (0x1ul << OTG_INTEN_VBCHGIEN_Pos) /*!< OTG_T::INTEN: VBCHGIEN Mask */ #define OTG_INTEN_SECHGIEN_Pos (11) /*!< OTG_T::INTEN: SECHGIEN Position */ #define OTG_INTEN_SECHGIEN_Msk (0x1ul << OTG_INTEN_SECHGIEN_Pos) /*!< OTG_T::INTEN: SECHGIEN Mask */ #define OTG_INTEN_SRPDETIEN_Pos (13) /*!< OTG_T::INTEN: SRPDETIEN Position */ #define OTG_INTEN_SRPDETIEN_Msk (0x1ul << OTG_INTEN_SRPDETIEN_Pos) /*!< OTG_T::INTEN: SRPDETIEN Mask */ #define OTG_INTSTS_ROLECHGIF_Pos (0) /*!< OTG_T::INTSTS: ROLECHGIF Position */ #define OTG_INTSTS_ROLECHGIF_Msk (0x1ul << OTG_INTSTS_ROLECHGIF_Pos) /*!< OTG_T::INTSTS: ROLECHGIF Mask */ #define OTG_INTSTS_VBEIF_Pos (1) /*!< OTG_T::INTSTS: VBEIF Position */ #define OTG_INTSTS_VBEIF_Msk (0x1ul << OTG_INTSTS_VBEIF_Pos) /*!< OTG_T::INTSTS: VBEIF Mask */ #define OTG_INTSTS_SRPFIF_Pos (2) /*!< OTG_T::INTSTS: SRPFIF Position */ #define OTG_INTSTS_SRPFIF_Msk (0x1ul << OTG_INTSTS_SRPFIF_Pos) /*!< OTG_T::INTSTS: SRPFIF Mask */ #define OTG_INTSTS_HNPFIF_Pos (3) /*!< OTG_T::INTSTS: HNPFIF Position */ #define OTG_INTSTS_HNPFIF_Msk (0x1ul << OTG_INTSTS_HNPFIF_Pos) /*!< OTG_T::INTSTS: HNPFIF Mask */ #define OTG_INTSTS_GOIDLEIF_Pos (4) /*!< OTG_T::INTSTS: GOIDLEIF Position */ #define OTG_INTSTS_GOIDLEIF_Msk (0x1ul << OTG_INTSTS_GOIDLEIF_Pos) /*!< OTG_T::INTSTS: GOIDLEIF Mask */ #define OTG_INTSTS_IDCHGIF_Pos (5) /*!< OTG_T::INTSTS: IDCHGIF Position */ #define OTG_INTSTS_IDCHGIF_Msk (0x1ul << OTG_INTSTS_IDCHGIF_Pos) /*!< OTG_T::INTSTS: IDCHGIF Mask */ #define OTG_INTSTS_PDEVIF_Pos (6) /*!< OTG_T::INTSTS: PDEVIF Position */ #define OTG_INTSTS_PDEVIF_Msk (0x1ul << OTG_INTSTS_PDEVIF_Pos) /*!< OTG_T::INTSTS: PDEVIF Mask */ #define OTG_INTSTS_HOSTIF_Pos (7) /*!< OTG_T::INTSTS: HOSTIF Position */ #define OTG_INTSTS_HOSTIF_Msk (0x1ul << OTG_INTSTS_HOSTIF_Pos) /*!< OTG_T::INTSTS: HOSTIF Mask */ #define OTG_INTSTS_BVLDCHGIF_Pos (8) /*!< OTG_T::INTSTS: BVLDCHGIF Position */ #define OTG_INTSTS_BVLDCHGIF_Msk (0x1ul << OTG_INTSTS_BVLDCHGIF_Pos) /*!< OTG_T::INTSTS: BVLDCHGIF Mask */ #define OTG_INTSTS_AVLDCHGIF_Pos (9) /*!< OTG_T::INTSTS: AVLDCHGIF Position */ #define OTG_INTSTS_AVLDCHGIF_Msk (0x1ul << OTG_INTSTS_AVLDCHGIF_Pos) /*!< OTG_T::INTSTS: AVLDCHGIF Mask */ #define OTG_INTSTS_VBCHGIF_Pos (10) /*!< OTG_T::INTSTS: VBCHGIF Position */ #define OTG_INTSTS_VBCHGIF_Msk (0x1ul << OTG_INTSTS_VBCHGIF_Pos) /*!< OTG_T::INTSTS: VBCHGIF Mask */ #define OTG_INTSTS_SECHGIF_Pos (11) /*!< OTG_T::INTSTS: SECHGIF Position */ #define OTG_INTSTS_SECHGIF_Msk (0x1ul << OTG_INTSTS_SECHGIF_Pos) /*!< OTG_T::INTSTS: SECHGIF Mask */ #define OTG_INTSTS_SRPDETIF_Pos (13) /*!< OTG_T::INTSTS: SRPDETIF Position */ #define OTG_INTSTS_SRPDETIF_Msk (0x1ul << OTG_INTSTS_SRPDETIF_Pos) /*!< OTG_T::INTSTS: SRPDETIF Mask */ #define OTG_STATUS_OVERCUR_Pos (0) /*!< OTG_T::STATUS: OVERCUR Position */ #define OTG_STATUS_OVERCUR_Msk (0x1ul << OTG_STATUS_OVERCUR_Pos) /*!< OTG_T::STATUS: OVERCUR Mask */ #define OTG_STATUS_IDSTS_Pos (1) /*!< OTG_T::STATUS: IDSTS Position */ #define OTG_STATUS_IDSTS_Msk (0x1ul << OTG_STATUS_IDSTS_Pos) /*!< OTG_T::STATUS: IDSTS Mask */ #define OTG_STATUS_SESSEND_Pos (2) /*!< OTG_T::STATUS: SESSEND Position */ #define OTG_STATUS_SESSEND_Msk (0x1ul << OTG_STATUS_SESSEND_Pos) /*!< OTG_T::STATUS: SESSEND Mask */ #define OTG_STATUS_BVLD_Pos (3) /*!< OTG_T::STATUS: BVLD Position */ #define OTG_STATUS_BVLD_Msk (0x1ul << OTG_STATUS_BVLD_Pos) /*!< OTG_T::STATUS: BVLD Mask */ #define OTG_STATUS_AVLD_Pos (4) /*!< OTG_T::STATUS: AVLD Position */ #define OTG_STATUS_AVLD_Msk (0x1ul << OTG_STATUS_AVLD_Pos) /*!< OTG_T::STATUS: AVLD Mask */ #define OTG_STATUS_VBUSVLD_Pos (5) /*!< OTG_T::STATUS: VBUSVLD Position */ #define OTG_STATUS_VBUSVLD_Msk (0x1ul << OTG_STATUS_VBUSVLD_Pos) /*!< OTG_T::STATUS: VBUSVLD Mask */ #define OTG_STATUS_ASPERI_Pos (6) /*!< OTG_T::STATUS: ASPERI Position */ #define OTG_STATUS_ASPERI_Msk (0x1ul << OTG_STATUS_ASPERI_Pos) /*!< OTG_T::STATUS: ASPERI Mask */ #define OTG_STATUS_ASHOST_Pos (7) /*!< OTG_T::STATUS: ASHOST Position */ #define OTG_STATUS_ASHOST_Msk (0x1ul << OTG_STATUS_ASHOST_Pos) /*!< OTG_T::STATUS: ASHOST Mask */ /**@}*/ /* OTG_CONST */ /**@}*/ /* end of OTG register group */ #endif /* __OTG_REG_H__ */