File content as of revision 12:ec9768677cea:

#include "dot_util.h"
 
#if ACTIVE_EXAMPLE == AUTO_OTA_EXAMPLE

/////////////////////////////////////////////////////////////
// * these options must match the settings on your gateway //
// * edit their values to match your configuration         //
// * frequency sub band is only relevant for the 915 bands //
// * either the network name and passphrase can be used or //
//     the network ID (8 bytes) and KEY (16 bytes)         //
/////////////////////////////////////////////////////////////
static std::string network_name = "MultiTech";
static std::string network_passphrase = "MultiTech";
static uint8_t network_id[] = { 0x6C, 0x4E, 0xEF, 0x66, 0xF4, 0x79, 0x86, 0xA6 };
static uint8_t network_key[] = { 0x1F, 0x33, 0xA1, 0x70, 0xA5, 0xF1, 0xFD, 0xA0, 0xAB, 0x69, 0x7A, 0xAE, 0x2B, 0x95, 0x91, 0x6B };
static uint8_t frequency_sub_band = 0;
static bool public_network = false;
static uint8_t ack = 1;

// deepsleep consumes slightly less current than sleep
// in sleep mode, IO state is maintained, RAM is retained, and application will resume after waking up
// in deepsleep mode, IOs float, RAM is lost, and application will start from beginning after waking up
// if deep_sleep == true, device will enter deepsleep mode
static bool deep_sleep = true;

mDot* dot = NULL;

Serial pc(USBTX, USBRX);

#if defined(TARGET_XDOT_L151CC)
I2C i2c(I2C_SDA, I2C_SCL);
ISL29011 lux(i2c);
#else
AnalogIn lux(XBEE_AD0);
#endif

int main() {
    pc.baud(115200);

    mts::MTSLog::setLogLevel(mts::MTSLog::TRACE_LEVEL);
    
    dot = mDot::getInstance();

    if (!dot->getStandbyFlag()) {
        // start from a well-known state
        logInfo("defaulting Dot configuration");
        dot->resetConfig();
        dot->resetNetworkSession();

        // make sure library logging is turned on
        dot->setLogLevel(mts::MTSLog::INFO_LEVEL);

        // update configuration if necessary
        // in AUTO_OTA mode the session is automatically saved, so saveNetworkSession and restoreNetworkSession are not needed
        if (dot->getJoinMode() != mDot::AUTO_OTA) {
            logInfo("changing network join mode to AUTO_OTA");
            if (dot->setJoinMode(mDot::AUTO_OTA) != mDot::MDOT_OK) {
                logError("failed to set network join mode to AUTO_OTA");
            }
        }
        // in OTA and AUTO_OTA join modes, the credentials can be passed to the library as a name and passphrase or an ID and KEY
        // only one method or the other should be used!
        // network ID = crc64(network name)
        // network KEY = cmac(network passphrase)
        update_ota_config_name_phrase(network_name, network_passphrase, frequency_sub_band, public_network, ack);
        //update_ota_config_id_key(network_id, network_key, frequency_sub_band, public_network, ack);
    
        // save changes to configuration
        logInfo("saving configuration");
        if (!dot->saveConfig()) {
            logError("failed to save configuration");
        }
    
        // display configuration
        display_config();
    }

    while (true) {
        uint16_t light;
        std::vector<uint8_t> tx_data;

        // join network if not joined
        if (!dot->getNetworkJoinStatus()) {
            join_network();
        }

#if defined(TARGET_XDOT_L151CC)
        // configure the ISL29011 sensor on the xDot-DK for continuous ambient light sampling, 16 bit conversion, and maximum range
        lux.setMode(ISL29011::ALS_CONT);
        lux.setResolution(ISL29011::ADC_16BIT);
        lux.setRange(ISL29011::RNG_64000);

        // get the latest light sample and send it to the gateway
        light = lux.getData();
        tx_data.push_back((light >> 8) & 0xFF);
        tx_data.push_back(light & 0xFF);
        logInfo("light: %lu [0x%04X]", light, light);
        send_data(tx_data);

        // put the LSL29011 ambient light sensor into a low power state
        lux.setMode(ISL29011::PWR_DOWN);
#else 
        // get some dummy data and send it to the gateway
        light = lux.read_u16();
        tx_data.push_back((light >> 8) & 0xFF);
        tx_data.push_back(light & 0xFF);
        logInfo("light: %lu [0x%04X]", light, light);
        send_data(tx_data);
#endif

        // ONLY ONE of the three functions below should be uncommented depending on the desired wakeup method
        //sleep_wake_rtc_only(deep_sleep);
        //sleep_wake_interrupt_only(deep_sleep);
        sleep_wake_rtc_or_interrupt(deep_sleep);
    }
 
    return 0;
}

#endif