Jinbuhm Kim
/
W5500_Driver
Wiznet W5500 driver and TCP/UDP loopback
Diff: Ethernet/wizchip_conf.h
- Revision:
- 0:2513c6696bdc
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/Ethernet/wizchip_conf.h Fri Dec 13 07:35:58 2013 +0000 @@ -0,0 +1,404 @@ +/* Wiznet W5500 Library + * Copyright (c) 2013, WIZnet Co., LTD. + * + * Licensed under the Apache License, Version 2.0 (the "License"); + * you may not use this file except in compliance with the License. + * You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an "AS IS" BASIS, + * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + */ + +/** + * @defgroup extra_functions 2. WIZnet Extra Functions + * + * @brief These functions is optional function. It could be replaced at WIZCHIP I/O function because they were made by WIZCHIP I/O functions. + * @details There are functions of configuring WIZCHIP, network, interrupt, phy, network information and timer. \n + * + */ +#ifdef __cplusplus +extern "C" { +#endif + +#ifndef _WIZCHIP_CONF_H_ +#define _WIZCHIP_CONF_H_ + +#include <stdint.h> +#include "W5500/w5500.h" + +#define _WIZCHIP_SOCK_NUM_ 8 ///< The count of independant socket of @b WIZCHIP + + +/******************************************************** +* WIZCHIP BASIC IF functions for SPI, SDIO, I2C , ETC. +*********************************************************/ +/** + * @ingroup DATA_TYPE + * @brief The set of callback functions for W5500:@ref WIZCHIP_IO_Functions W5200:@ref WIZCHIP_IO_Functions_W5200 + */ +typedef struct __WIZCHIP +{ + /** + * The set of critical section callback func. + */ + struct _CRIS + { + void (*_enter) (void); ///< crtical section enter + void (*_exit) (void); ///< critial section exit + }CRIS; + /** + * The set of @ref\_WIZCHIP_ select control callback func. + */ + struct _CS + { + void (*_select) (void); ///< @ref \_WIZCHIP_ selected + void (*_deselect)(void); ///< @ref \_WIZCHIP_ deselected + }CS; + /** + * The set of interface IO callback func. + */ + union _IF + { + /** + * For SPI interface IO + */ + struct + { + uint8_t (*_read_byte) (void); + void (*_write_byte) (uint8_t wb); + }SPI; + }IF; +}_WIZCHIP; + +extern _WIZCHIP WIZCHIP; + +/** + * @ingroup DATA_TYPE + * WIZCHIP control type enumration used in @ref ctlwizchip(). + */ +typedef enum +{ + CW_RESET_WIZCHIP, ///< Resets WIZCHIP by softly + CW_INIT_WIZCHIP, ///< Inializes to WIZCHIP with SOCKET buffer size 2 or 1 dimension array typed uint8_t. + CW_GET_INTERRUPT, ///< Get Interrupt status of WIZCHIP + CW_CLR_INTERRUPT, ///< Clears interrupt + CW_SET_INTRMASK, ///< Masks interrupt + CW_GET_INTRMASK, ///< Get interrupt mask + CW_SET_INTRTIME, ///< Set interval time between the current and next interrupt. + CW_GET_INTRTIME, ///< Set interval time between the current and next interrupt. + CW_GET_ID, ///< Gets WIZCHIP name. + + CW_RESET_PHY, ///< Resets internal PHY. Valid Only W5000 + CW_SET_PHYCONF, ///< When PHY configured by interal register, PHY operation mode (Manual/Auto, 10/100, Half/Full). Valid Only W5000 + CW_GET_PHYCONF, ///< Get PHY operation mode in interal register. Valid Only W5000 + CW_GET_PHYSTATUS, ///< Get real PHY status on operating. Valid Only W5000 + CW_SET_PHYPOWMODE, ///< Set PHY power mode as noraml and down when PHYSTATUS.OPMD == 1. Valid Only W5000 + + CW_GET_PHYPOWMODE, ///< Get PHY Power mode as down or normal + CW_GET_PHYLINK ///< Get PHY Link status +}ctlwizchip_type; + +/** + * @ingroup DATA_TYPE + * Network control type enumration used in @ref ctlnetwork(). + */ +typedef enum +{ + CN_SET_NETINFO, ///< Set Network with @ref wiz_NetInfo + CN_GET_NETINFO, ///< Get Network with @ref wiz_NetInfo + CN_SET_NETMODE, ///< Set network mode as WOL, PPPoE, Ping Block, and Force ARP mode + CN_GET_NETMODE, ///< Get network mode as WOL, PPPoE, Ping Block, and Force ARP mode + CN_SET_TIMEOUT, ///< Set network timeout as retry count and time. + CN_GET_TIMEOUT, ///< Get network timeout as retry count and time. +}ctlnetwork_type; + +/** + * @ingroup DATA_TYPE + * Interrupt kind when CW_SET_INTRRUPT, CW_GET_INTERRUPT, CW_SET_INTRMASK + * and CW_GET_INTRMASK is used in @ref ctlnetwork(). + * It can be used with OR operation. + */ +typedef enum +{ + IK_WOL = (1 << 4), ///< Wake On Lan by receiving the magic packet. Valid in W500. + + IK_PPPOE_TERMINATED = (1 << 5), ///< PPPoE Disconnected + + IK_DEST_UNREACH = (1 << 6), ///< Destination IP & Port Unreable, No use in W5200 + + IK_IP_CONFLICT = (1 << 7), ///< IP conflict occurred + + IK_SOCK_0 = (1 << 8), ///< Socket 0 interrupt + IK_SOCK_1 = (1 << 9), ///< Socket 1 interrupt + IK_SOCK_2 = (1 << 10), ///< Socket 2 interrupt + IK_SOCK_3 = (1 << 11), ///< Socket 3 interrupt + IK_SOCK_4 = (1 << 12), ///< Socket 4 interrupt, No use in 5100 + IK_SOCK_5 = (1 << 13), ///< Socket 5 interrupt, No use in 5100 + IK_SOCK_6 = (1 << 14), ///< Socket 6 interrupt, No use in 5100 + IK_SOCK_7 = (1 << 15), ///< Socket 7 interrupt, No use in 5100 + + IK_SOCK_ALL = (0xFF << 8) ///< All Socket interrpt +}intr_kind; + +#define PHY_CONFBY_HW 0 ///< Configured PHY operation mode by HW pin +#define PHY_CONFBY_SW 1 ///< Configured PHY operation mode by SW register +#define PHY_MODE_MANUAL 0 ///< Configured PHY operation mode with user setting. +#define PHY_MODE_AUTONEGO 1 ///< Configured PHY operation mode with auto-negotiation +#define PHY_SPEED_10 0 ///< Link Speed 10 +#define PHY_SPEED_100 1 ///< Link Speed 100 +#define PHY_DUPLEX_HALF 0 ///< Link Half-Duplex +#define PHY_DUPLEX_FULL 1 ///< Link Full-Duplex +#define PHY_LINK_OFF 0 ///< Link Off +#define PHY_LINK_ON 1 ///< Link On +#define PHY_POWER_NORM 0 ///< PHY power normal mode +#define PHY_POWER_DOWN 1 ///< PHY power down mode + + +/** + * @ingroup DATA_TYPE + * It configures PHY configuration when CW_SET PHYCONF or CW_GET_PHYCONF in W5500, + * and it indicates the real PHY status configured by HW or SW in all WIZCHIP. \n + * Valid only in W5500. + */ +typedef struct wiz_PhyConf_t +{ + uint8_t by; ///< set by @ref PHY_CONFBY_HW or @ref PHY_CONFBY_SW + uint8_t mode; ///< set by @ref PHY_MODE_MANUAL or @ref PHY_MODE_AUTONEGO + uint8_t speed; ///< set by @ref PHY_SPEED_10 or @ref PHY_SPEED_100 + uint8_t duplex; ///< set by @ref PHY_DUPLEX_HALF @ref PHY_DUPLEX_FULL + //uint8_t power; ///< set by @ref PHY_POWER_NORM or @ref PHY_POWER_DOWN + //uint8_t link; ///< Valid only in CW_GET_PHYSTATUS. set by @ref PHY_LINK_ON or PHY_DUPLEX_OFF + }wiz_PhyConf; + +/** + * @ingroup DATA_TYPE + * It used in setting dhcp_mode of @ref wiz_NetInfo. + */ +typedef enum +{ + NETINFO_STATIC = 1, ///< Static IP configuration by manually. + NETINFO_DHCP ///< Dynamic IP configruation from a DHCP sever +}dhcp_mode; + +/** + * @ingroup DATA_TYPE + * Network Information for WIZCHIP + */ +typedef struct wiz_NetInfo_t +{ + uint8_t mac[6]; ///< Source Mac Address + uint8_t ip[4]; ///< Source IP Address + uint8_t sn[4]; ///< Subnet Mask + uint8_t gw[4]; ///< Gateway IP Address + uint8_t dns[4]; ///< DNS server IP Address + dhcp_mode dhcp; ///< 1 - Static, 2 - DHCP +}wiz_NetInfo; + +/** + * @ingroup DATA_TYPE + * Network mode + */ +typedef enum +{ + NM_FORCEARP = (1<<1), ///< Force to APP send whenever udp data is sent. Valid only in W5500 + NM_WAKEONLAN = (1<<5), ///< Wake On Lan + NM_PINGBLOCK = (1<<4), ///< Block ping-request + NM_PPPOE = (1<<3), ///< PPPoE mode +}netmode_type; + +/** + * @ingroup DATA_TYPE + * Used in CN_SET_TIMEOUT or CN_GET_TIMEOUT of @ref ctlwizchip() for timeout configruation. + */ +typedef struct wiz_NetTimeout_t +{ + uint8_t retry_cnt; ///< retry count + uint16_t time_100us; ///< time unit 100us +}wiz_NetTimeout; + +/** + *@brief Registers call back function for critical section of I/O functions such as + *\ref WIZCHIP_READ, @ref WIZCHIP_WRITE, @ref WIZCHIP_READ_BUF and @ref WIZCHIP_WRITE_BUF. + *@param cris_en : callback function for critical section enter. + *@param cris_ex : callback function for critical section exit. + *@todo Describe @ref WIZCHIP_CRITICAL_ENTER and @ref WIZCHIP_CRITICAL_EXIT marco or register your functions. + *@note If you do not describe or register, default functions(@ref wizchip_cris_enter & @ref wizchip_cris_exit) is called. + */ +void reg_wizchip_cris_cbfunc(void(*cris_en)(void), void(*cris_ex)(void)); + + +/** + *@brief Registers call back function for WIZCHIP select & deselect. + *@param cs_sel : callback function for WIZCHIP select + *@param cs_desel : callback fucntion for WIZCHIP deselect + *@todo Describe @ref wizchip_cs_select and @ref wizchip_cs_deselect function or register your functions. + *@note If you do not describe or register, null function is called. + */ +void reg_wizchip_cs_cbfunc(void(*cs_sel)(void), void(*cs_desel)(void)); + +/** + *@brief Registers call back function for SPI interface. + *@param spi_rb : callback function to read byte usig SPI + *@param spi_wb : callback function to write byte usig SPI + *@todo Describe \ref wizchip_spi_readbyte and \ref wizchip_spi_writebyte function + *or register your functions. + *@note If you do not describe or register, null function is called. + */ +void reg_wizchip_spi_cbfunc(uint8_t (*spi_rb)(void), void (*spi_wb)(uint8_t wb)); + +/** + * @ingroup extra_functions + * @brief Controls to the WIZCHIP. + * @details Resets WIZCHIP & internal PHY, Configures PHY mode, Monitor PHY(Link,Speed,Half/Full/Auto), + * controls interrupt & mask and so on. + * @param cwtype : Decides to the control type + * @param arg : arg type is dependent on cwtype. + * @return 0 : Success \n + * -1 : Fail because of invalid \ref ctlwizchip_type or unsupported \ref ctlwizchip_type in WIZCHIP + */ +int8_t ctlwizchip(ctlwizchip_type cwtype, void* arg); + +/** + * @ingroup extra_functions + * @brief Controls to network. + * @details Controls to network environment, mode, timeout and so on. + * @param cntype : Input. Decides to the control type + * @param arg : Inout. arg type is dependent on cntype. + * @return -1 : Fail because of invalid \ref ctlnetwork_type or unsupported \ref ctlnetwork_type in WIZCHIP \n + * 0 : Success + */ +int8_t ctlnetwork(ctlnetwork_type cntype, void* arg); + + +/* + * The following functions are implemented for internal use. + * but You can call these functions for code size reduction instead of ctlwizchip() and ctlnetwork(). + */ + +/** + * @ingroup extra_functions + * @brief Reset WIZCHIP by softly. + */ +void wizchip_sw_reset(void); + +/** + * @ingroup extra_functions + * @brief Initializes WIZCHIP with socket buffer size + * @param txsize Socket tx buffer sizes. If null, initialized the default size 2KB. + * @param rxsize Socket rx buffer sizes. If null, initialized the default size 2KB. + * @return 0 : succcess \n + * -1 : fail. Invalid buffer size + */ +int8_t wizchip_init(uint8_t* txsize, uint8_t* rxsize); + +/** + * @ingroup extra_functions + * @brief Clear Interrupt of WIZCHIP. + * @param intr : @ref intr_kind value operated OR. It can type-cast to uint16_t. + */ +void wizchip_clrinterrupt(intr_kind intr); + +/** + * @ingroup extra_functions + * @brief Get Interrupt of WIZCHIP. + * @return @ref intr_kind value operated OR. It can type-cast to uint16_t. + */ +intr_kind wizchip_getinterrupt(void); + +/** + * @ingroup extra_functions + * @brief Mask or Unmask Interrupt of WIZCHIP. + * @param intr : @ref intr_kind value operated OR. It can type-cast to uint16_t. + */ +void wizchip_setinterruptmask(intr_kind intr); + +/** + * @ingroup extra_functions + * @brief Get Interrupt mask of WIZCHIP. + * @return : The operated OR vaule of @ref intr_kind. It can type-cast to uint16_t. + */ +intr_kind wizchip_getinterruptmask(void); + +int8_t wizphy_getphylink(void); ///< get the link status of phy in WIZCHIP. No use in W5100 +int8_t wizphy_getphypmode(void); ///< get the power mode of PHY in WIZCHIP. No use in W5100 + + void wizphy_reset(void); ///< Reset phy. Vailid only in W5500 +/** + * @ingroup extra_functions + * @brief Set the phy information for WIZCHIP without power mode + * @param phyconf : @ref wiz_PhyConf + */ + void wizphy_setphyconf(wiz_PhyConf* phyconf); + /** + * @ingroup extra_functions + * @brief Get phy configuration information. + * @param phyconf : @ref wiz_PhyConf + */ + void wizphy_getphyconf(wiz_PhyConf* phyconf); + /** + * @ingroup extra_functions + * @brief Get phy status. + * @param phyconf : @ref wiz_PhyConf + */ + void wizphy_getphystat(wiz_PhyConf* phyconf); + /** + * @ingroup extra_functions + * @brief set the power mode of phy inside WIZCHIP. Refer to @ref PHYCFGR in W5500, @ref PHYSTATUS in W5200 + * @param pmode Settig value of power down mode. + */ + int8_t wizphy_setphypmode(uint8_t pmode); + +/** +* @ingroup extra_functions + * @brief Set the network information for WIZCHIP + * @param pnetinfo : @ref wizNetInfo + */ +void wizchip_setnetinfo(wiz_NetInfo* pnetinfo); + +/** + * @ingroup extra_functions + * @brief Get the network information for WIZCHIP + * @param pnetinfo : @ref wizNetInfo + */ +void wizchip_getnetinfo(wiz_NetInfo* pnetinfo); + +/** + * @ingroup extra_functions + * @brief Set the network mode such WOL, PPPoE, Ping Block, and etc. + * @param pnetinfo Value of network mode. Refer to @ref netmode_type. + */ +int8_t wizchip_setnetmode(netmode_type netmode); + +/** + * @ingroup extra_functions + * @brief Get the network mode such WOL, PPPoE, Ping Block, and etc. + * @return Value of network mode. Refer to @ref netmode_type. + */ +netmode_type wizchip_getnetmode(void); + +/** + * @ingroup extra_functions + * @brief Set retry time value(@ref RTR) and retry count(@ref RCR). + * @details @ref RTR configures the retransmission timeout period and @ref RCR configures the number of time of retransmission. + * @param nettime @ref RTR value and @ref RCR value. Refer to @ref wiz_NetTimeout. + */ +void wizchip_settimeout(wiz_NetTimeout* nettime); + +/** + * @ingroup extra_functions + * @brief Get retry time value(@ref RTR) and retry count(@ref RCR). + * @details @ref RTR configures the retransmission timeout period and @ref RCR configures the number of time of retransmission. + * @param nettime @ref RTR value and @ref RCR value. Refer to @ref wiz_NetTimeout. + */ +void wizchip_gettimeout(wiz_NetTimeout* nettime); + +#endif // _WIZCHIP_CONF_H_ + +#ifdef __cplusplus +} +#endif