mbed library sources modified for open wear
Dependents: openwear-lifelogger-example
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_F334R8/stm32f3xx_hal_smbus.c
- Revision:
- 237:f3da66175598
diff -r 6ac0938ee349 -r f3da66175598 targets/cmsis/TARGET_STM/TARGET_NUCLEO_F334R8/stm32f3xx_hal_smbus.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_F334R8/stm32f3xx_hal_smbus.c Tue Jun 24 14:45:08 2014 +0100 @@ -0,0 +1,1902 @@ +/** + ****************************************************************************** + * @file stm32f3xx_hal_smbus.c + * @author MCD Application Team + * @version V1.0.1 + * @date 18-June-2014 + * @brief SMBUS HAL module driver. + * + * This file provides firmware functions to manage the following + * functionalities of the System Management Bus (SMBus) peripheral, + * based on I2C principales of operation : + * + Initialization and de-initialization functions + * + IO operation functions + * + Peripheral State and Errors functions + * + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + The SMBUS HAL driver can be used as follows: + + (#) Declare a SMBUS_HandleTypeDef handle structure, for example: + SMBUS_HandleTypeDef hsmbus; + + (#)Initialize the SMBUS low level resources by implement the HAL_SMBUS_MspInit ()API: + (##) Enable the SMBUSx interface clock + (##) SMBUS pins configuration + (+++) Enable the clock for the SMBUS GPIOs + (+++) Configure SMBUS pins as alternate function open-drain + (##) NVIC configuration if you need to use interrupt process + (+++) Configure the SMBUSx interrupt priority + (+++) Enable the NVIC SMBUS IRQ Channel + + (#) Configure the Communication Clock Timing, Bus Timeout, Own Address1, Master Adressing Mode, + Dual Addressing mode, Own Address2, Own Address2 Mask, General call, Nostretch mode, + Peripheral mode and Packet Error Check mode in the hsmbus Init structure. + + (#) Initialize the SMBUS registers by calling the HAL_SMBUS_Init() API: + (+) These API's configures also the low level Hardware GPIO, CLOCK, CORTEX...etc) + by calling the customed HAL_SMBUS_MspInit(&hsmbus) API. + + (#) To check if target device is ready for communication, use the function HAL_SMBUS_IsDeviceReady() + + (#) For SMBUS IO operations, only one mode of operations is available within this driver : + + *** Interrupt mode IO operation *** + =================================== + [..] + (+) Transmit in master/host SMBUS mode an amount of data in non blocking mode using HAL_SMBUS_Master_Transmit_IT() + (++) At transmission end of transfer HAL_SMBUS_MasterTxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_SMBUS_MasterTxCpltCallback + (+) Receive in master/host SMBUS mode an amount of data in non blocking mode using HAL_SMBUS_Master_Receive_IT() + (++) At reception end of transfer HAL_SMBUS_MasterRxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_SMBUS_MasterRxCpltCallback + (+) Abort a master/host SMBUS process commnunication with Interrupt using HAL_SMBUS_Master_Abort_IT() + (++) The associated previous transfer callback is called at the end of abort process + (++) mean HAL_SMBUS_MasterTxCpltCallback in case of previous state was master transmit + (++) mean HAL_SMBUS_MasterRxCpltCallback in case of previous state was master receive + (+) Enable/disable the Address listen mode in slave/device or host/slave SMBUS mode + using HAL_SMBUS_Slave_Listen_IT() HAL_SMBUS_DisableListen_IT() + (++) When address slave/device SMBUS match, HAL_SMBUS_SlaveAddrCallback is executed and user can + add his own code to check the Address Match Code and the transmission direction request by master/host (Write/Read). + (++) At Listen mode end HAL_SMBUS_SlaveListenCpltCallback is executed and user can + add his own code by customization of function pointer HAL_SMBUS_SlaveListenCpltCallback + (+) Transmit in slave/device SMBUS mode an amount of data in non blocking mode using HAL_SMBUS_Slave_Transmit_IT() + (++) At transmission end of transfer HAL_SMBUS_SlaveTxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_SMBUS_SlaveTxCpltCallback + (+) Receive in slave/device SMBUS mode an amount of data in non blocking mode using HAL_SMBUS_Slave_Receive_IT() + (++) At reception end of transfer HAL_SMBUS_SlaveRxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_SMBUS_SlaveRxCpltCallback + (+) Enable/Disable the SMBUS alert mode using HAL_SMBUS_EnableAlert_IT() HAL_SMBUS_DisableAlert_IT() + (++) When SMBUS Alert is generated HAL_SMBUS_ErrorCallback() is executed and user can + add his own code by customization of function pointer HAL_SMBUS_ErrorCallback + to check the Alert Error Code using function HAL_SMBUS_GetError() + (+) Get HAL state machine or error values using HAL_SMBUS_GetState() or HAL_SMBUS_GetError() + (+) In case of transfer Error, HAL_SMBUS_ErrorCallback() function is executed and user can + add his own code by customization of function pointer HAL_SMBUS_ErrorCallback + to check the Error Code using function HAL_SMBUS_GetError() + + *** SMBUS HAL driver macros list *** + ================================== + [..] + Below the list of most used macros in SMBUS HAL driver. + + (+) __HAL_SMBUS_ENABLE: Enable the SMBUS peripheral + (+) __HAL_SMBUS_DISABLE: Disable the SMBUS peripheral + (+) __HAL_SMBUS_GET_FLAG : Checks whether the specified SMBUS flag is set or not + (+) __HAL_SMBUS_CLEAR_FLAG : Clears the specified SMBUS pending flag + (+) __HAL_SMBUS_ENABLE_IT: Enables the specified SMBUS interrupt + (+) __HAL_SMBUS_DISABLE_IT: Disables the specified SMBUS interrupt + + [..] + (@) You can refer to the SMBUS HAL driver header file for more useful macros + + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f3xx_hal.h" + +/** @addtogroup STM32F3xx_HAL_Driver + * @{ + */ + +/** @defgroup SMBUS + * @brief SMBUS HAL module driver + * @{ + */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +#define TIMING_CLEAR_MASK ((uint32_t)0xF0FFFFFF) /*<! SMBUS TIMING clear register Mask */ +#define HAL_TIMEOUT_ADDR ((uint32_t)10000) /* 10 s */ +#define HAL_TIMEOUT_BUSY ((uint32_t)25) /* 25 ms */ +#define HAL_TIMEOUT_DIR ((uint32_t)25) /* 25 ms */ +#define HAL_TIMEOUT_RXNE ((uint32_t)25) /* 25 ms */ +#define HAL_TIMEOUT_STOPF ((uint32_t)25) /* 25 ms */ +#define HAL_TIMEOUT_TC ((uint32_t)25) /* 25 ms */ +#define HAL_TIMEOUT_TCR ((uint32_t)25) /* 25 ms */ +#define HAL_TIMEOUT_TXIS ((uint32_t)25) /* 25 ms */ +#define MAX_NBYTE_SIZE 255 + +/* Private macro -------------------------------------------------------------*/ +#define __SMBUS_GET_ISR_REG(__HANDLE__) ((__HANDLE__)->Instance->ISR) +#define __SMBUS_CHECK_FLAG(__ISR__, __FLAG__) ((((__ISR__) & ((__FLAG__) & SMBUS_FLAG_MASK)) == ((__FLAG__) & SMBUS_FLAG_MASK))) + +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +static HAL_StatusTypeDef SMBUS_WaitOnFlagUntilTimeout(SMBUS_HandleTypeDef *hsmbus, uint32_t Flag, FlagStatus Status, uint32_t Timeout); + +static HAL_StatusTypeDef SMBUS_Enable_IRQ(SMBUS_HandleTypeDef *hsmbus, uint16_t InterruptRequest); +static HAL_StatusTypeDef SMBUS_Disable_IRQ(SMBUS_HandleTypeDef *hsmbus, uint16_t InterruptRequest); +static HAL_StatusTypeDef SMBUS_Master_ISR(SMBUS_HandleTypeDef *hsmbus); +static HAL_StatusTypeDef SMBUS_Slave_ISR(SMBUS_HandleTypeDef *hsmbus); + +static void SMBUS_TransferConfig(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t Size, uint32_t Mode, uint32_t Request); + +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup SMBUS_Private_Functions + * @{ + */ + +/** @defgroup HAL_SMBUS_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and de-initialization functions ##### + =============================================================================== + [..] This subsection provides a set of functions allowing to initialize and + de-initialiaze the SMBUSx peripheral: + + (+) User must Implement HAL_SMBUS_MspInit() function in which he configures + all related peripherals resources (CLOCK, GPIO, IT and NVIC ). + + (+) Call the function HAL_SMBUS_Init() to configure the selected device with + the selected configuration: + (++) Clock Timing + (++) Bus Timeout + (++) Analog Filer mode + (++) Own Address 1 + (++) Addressing mode (Master, Slave) + (++) Dual Addressing mode + (++) Own Address 2 + (++) Own Address 2 Mask + (++) General call mode + (++) Nostretch mode + (++) Packet Error Check mode + (++) Peripheral mode + + + (+) Call the function HAL_SMBUS_DeInit() to restore the default configuration + of the selected SMBUSx periperal. + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the SMBUS according to the specified parameters + * in the SMBUS_InitTypeDef and create the associated handle. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_Init(SMBUS_HandleTypeDef *hsmbus) +{ + /* Check the SMBUS handle allocation */ + if(hsmbus == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance)); + assert_param(IS_SMBUS_ANALOG_FILTER(hsmbus->Init.AnalogFilter)); + assert_param(IS_SMBUS_OWN_ADDRESS1(hsmbus->Init.OwnAddress1)); + assert_param(IS_SMBUS_ADDRESSING_MODE(hsmbus->Init.AddressingMode)); + assert_param(IS_SMBUS_DUAL_ADDRESS(hsmbus->Init.DualAddressMode)); + assert_param(IS_SMBUS_OWN_ADDRESS2(hsmbus->Init.OwnAddress2)); + assert_param(IS_SMBUS_OWN_ADDRESS2_MASK(hsmbus->Init.OwnAddress2Masks)); + assert_param(IS_SMBUS_GENERAL_CALL(hsmbus->Init.GeneralCallMode)); + assert_param(IS_SMBUS_NO_STRETCH(hsmbus->Init.NoStretchMode)); + assert_param(IS_SMBUS_PEC(hsmbus->Init.PacketErrorCheckMode)); + assert_param(IS_SMBUS_PERIPHERAL_MODE(hsmbus->Init.PeripheralMode)); + + if(hsmbus->State == HAL_SMBUS_STATE_RESET) + { + /* Init the low level hardware : GPIO, CLOCK, NVIC */ + HAL_SMBUS_MspInit(hsmbus); + } + + hsmbus->State = HAL_SMBUS_STATE_BUSY; + + /* Disable the selected SMBUS peripheral */ + __HAL_SMBUS_DISABLE(hsmbus); + + /*---------------------------- SMBUSx TIMINGR Configuration ------------------------*/ + /* Configure SMBUSx: Frequency range */ + hsmbus->Instance->TIMINGR = hsmbus->Init.Timing & TIMING_CLEAR_MASK; + + /*---------------------------- SMBUSx TIMEOUTR Configuration ------------------------*/ + /* Configure SMBUSx: Bus Timeout */ + hsmbus->Instance->TIMEOUTR &= ~I2C_TIMEOUTR_TIMOUTEN; + hsmbus->Instance->TIMEOUTR &= ~I2C_TIMEOUTR_TEXTEN; + hsmbus->Instance->TIMEOUTR = hsmbus->Init.SMBusTimeout; + + /*---------------------------- SMBUSx OAR1 Configuration -----------------------*/ + /* Configure SMBUSx: Own Address1 and ack own address1 mode */ + hsmbus->Instance->OAR1 &= ~I2C_OAR1_OA1EN; + + if(hsmbus->Init.OwnAddress1 != 0) + { + if(hsmbus->Init.AddressingMode == SMBUS_ADDRESSINGMODE_7BIT) + { + hsmbus->Instance->OAR1 = (I2C_OAR1_OA1EN | hsmbus->Init.OwnAddress1); + } + else /* SMBUS_ADDRESSINGMODE_10BIT */ + { + hsmbus->Instance->OAR1 = (I2C_OAR1_OA1EN | I2C_OAR1_OA1MODE | hsmbus->Init.OwnAddress1); + } + } + + /*---------------------------- SMBUSx CR2 Configuration ------------------------*/ + /* Configure SMBUSx: Addressing Master mode */ + if(hsmbus->Init.AddressingMode == SMBUS_ADDRESSINGMODE_10BIT) + { + hsmbus->Instance->CR2 = (I2C_CR2_ADD10); + } + /* Enable the AUTOEND by default, and enable NACK (should be disable only during Slave process) */ + /* AUTOEND and NACK bit will be manage during Transfer process */ + hsmbus->Instance->CR2 |= (I2C_CR2_AUTOEND | I2C_CR2_NACK); + + /*---------------------------- SMBUSx OAR2 Configuration -----------------------*/ + /* Configure SMBUSx: Dual mode and Own Address2 */ + hsmbus->Instance->OAR2 = (hsmbus->Init.DualAddressMode | hsmbus->Init.OwnAddress2 | (hsmbus->Init.OwnAddress2Masks << 8)); + + /*---------------------------- SMBUSx CR1 Configuration ------------------------*/ + /* Configure SMBUSx: Generalcall and NoStretch mode */ + hsmbus->Instance->CR1 = (hsmbus->Init.GeneralCallMode | hsmbus->Init.NoStretchMode | hsmbus->Init.PacketErrorCheckMode | hsmbus->Init.PeripheralMode | hsmbus->Init.AnalogFilter); + + /* Enable Slave Byte Control only in case of Packet Error Check is enabled and SMBUS Peripheral is set in Slave mode */ + if( (hsmbus->Init.PacketErrorCheckMode == SMBUS_PEC_ENABLED) + && ( (hsmbus->Init.PeripheralMode == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE) || (hsmbus->Init.PeripheralMode == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE_ARP) ) ) + { + hsmbus->Instance->CR1 |= I2C_CR1_SBC; + } + + /* Enable the selected SMBUS peripheral */ + __HAL_SMBUS_ENABLE(hsmbus); + + hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE; + hsmbus->PreviousState = HAL_SMBUS_STATE_READY; + hsmbus->State = HAL_SMBUS_STATE_READY; + + return HAL_OK; +} + +/** + * @brief DeInitializes the SMBUS peripheral. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_DeInit(SMBUS_HandleTypeDef *hsmbus) +{ + /* Check the SMBUS handle allocation */ + if(hsmbus == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance)); + + hsmbus->State = HAL_SMBUS_STATE_BUSY; + + /* Disable the SMBUS Peripheral Clock */ + __HAL_SMBUS_DISABLE(hsmbus); + + /* DeInit the low level hardware: GPIO, CLOCK, NVIC */ + HAL_SMBUS_MspDeInit(hsmbus); + + hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE; + hsmbus->PreviousState = HAL_SMBUS_STATE_RESET; + hsmbus->State = HAL_SMBUS_STATE_RESET; + + /* Release Lock */ + __HAL_UNLOCK(hsmbus); + + return HAL_OK; +} + +/** + * @brief SMBUS MSP Init. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval None + */ + __weak void HAL_SMBUS_MspInit(SMBUS_HandleTypeDef *hsmbus) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SMBUS_MspInit could be implemented in the user file + */ +} + +/** + * @brief SMBUS MSP DeInit + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval None + */ + __weak void HAL_SMBUS_MspDeInit(SMBUS_HandleTypeDef *hsmbus) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SMBUS_MspDeInit could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup HAL_SMBUS_Group2 IO operation functions + * @brief Data transfers functions + * +@verbatim + =============================================================================== + ##### IO operation functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to manage the SMBUS data + transfers. + + (#) Blocking mode function to check if device is ready for usage is : + (++) HAL_SMBUS_IsDeviceReady() + + (#) There is only one mode of transfer: + (++) No-Blocking mode : The communication is performed using Interrupts. + These functions return the status of the transfer startup. + The end of the data processing will be indicated through the + dedicated SMBUS IRQ when using Interrupt mode. + + (#) No-Blocking mode functions with Interrupt are : + (++) HAL_SMBUS_Master_Transmit_IT() + (++) HAL_SMBUS_Master_Receive_IT() + (++) HAL_SMBUS_Slave_Transmit_IT() + (++) HAL_SMBUS_Slave_Receive_IT() + (++) HAL_SMBUS_Slave_Listen_IT() or alias HAL_SMBUS_EnableListen_IT() + (++) HAL_SMBUS_DisableListen_IT() + (++) HAL_SMBUS_EnableAlert_IT() + (++) HAL_SMBUS_DisableAlert_IT() + + (#) A set of Transfer Complete Callbacks are provided in No_Blocking mode: + (++) HAL_SMBUS_MasterTxCpltCallback() + (++) HAL_SMBUS_MasterRxCpltCallback() + (++) HAL_SMBUS_SlaveTxCpltCallback() + (++) HAL_SMBUS_SlaveRxCpltCallback() + (++) HAL_SMBUS_SlaveAddrCallback() or alias HAL_SMBUS_AddrCallback() + (++) HAL_SMBUS_SlaveListenCpltCallback() or alias HAL_SMBUS_ListenCpltCallback() + (++) HAL_SMBUS_ErrorCallback() + +@endverbatim + * @{ + */ + +/** + * @brief Transmit in master/host SMBUS mode an amount of data in no-blocking mode with Interrupt + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @param DevAddress: Target device address + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be sent + * @param XferOptions: Options of Transfer, value of @ref SMBUS_XferOptions_definition + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_Master_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions) +{ + /* Check the parameters */ + assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if(hsmbus->State == HAL_SMBUS_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hsmbus); + + hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_TX; + hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE; + /* Prepare transfer parameters */ + hsmbus->pBuffPtr = pData; + hsmbus->XferCount = Size; + hsmbus->XferOptions = XferOptions; + + /* In case of Quick command, remove autoend mode */ + /* Manage the stop generation by software */ + if(hsmbus->pBuffPtr == NULL) + { + hsmbus->XferOptions &= ~SMBUS_AUTOEND_MODE; + } + + if(Size > MAX_NBYTE_SIZE) + { + hsmbus->XferSize = MAX_NBYTE_SIZE; + } + else + { + hsmbus->XferSize = Size; + } + + /* Send Slave Address */ + /* Set NBYTES to write and reload if size > MAX_NBYTE_SIZE and generate RESTART */ + if( (hsmbus->XferSize == MAX_NBYTE_SIZE) && (hsmbus->XferSize < hsmbus->XferCount) ) + { + SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_GENERATE_START_WRITE); + } + else + { + /* If transfer direction not change, do not generate Restart Condition */ + /* Mean Previous state is same as current state */ + if(hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_TX) + { + SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP); + } + /* Else transfer direction change, so generate Restart with new transfer direction */ + else + { + SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_GENERATE_START_WRITE); + } + + /* If PEC mode is enable, size to transmit manage by SW part should be Size-1 byte, corresponding to PEC byte */ + /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */ + if(__HAL_SMBUS_GET_PEC_MODE(hsmbus) != RESET) + { + hsmbus->XferSize--; + hsmbus->XferCount--; + } + } + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Note : The SMBUS interrupts must be enabled after unlocking current process + to avoid the risk of SMBUS interrupt handle execution before current + process unlock */ + SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_TX); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive in master/host SMBUS mode an amount of data in no-blocking mode with Interrupt + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @param DevAddress: Target device address + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be sent + * @param XferOptions: Options of Transfer, value of @ref SMBUS_XferOptions_definition + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_Master_Receive_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions) +{ + /* Check the parameters */ + assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if(hsmbus->State == HAL_SMBUS_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hsmbus); + + hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_RX; + hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE; + + /* Prepare transfer parameters */ + hsmbus->pBuffPtr = pData; + hsmbus->XferCount = Size; + hsmbus->XferOptions = XferOptions; + + /* In case of Quick command, remove autoend mode */ + /* Manage the stop generation by software */ + if(hsmbus->pBuffPtr == NULL) + { + hsmbus->XferOptions &= ~SMBUS_AUTOEND_MODE; + } + + if(Size > MAX_NBYTE_SIZE) + { + hsmbus->XferSize = MAX_NBYTE_SIZE; + } + else + { + hsmbus->XferSize = Size; + } + + /* Send Slave Address */ + /* Set NBYTES to write and reload if size > MAX_NBYTE_SIZE and generate RESTART */ + if( (hsmbus->XferSize == MAX_NBYTE_SIZE) && (hsmbus->XferSize < hsmbus->XferCount) ) + { + SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_GENERATE_START_READ); + } + else + { + /* If transfer direction not change, do not generate Restart Condition */ + /* Mean Previous state is same as current state */ + if(hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_RX) + { + SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP); + } + /* Else transfer direction change, so generate Restart with new transfer direction */ + else + { + SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_GENERATE_START_READ); + } + } + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Note : The SMBUS interrupts must be enabled after unlocking current process + to avoid the risk of SMBUS interrupt handle execution before current + process unlock */ + SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_RX); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Abort a master/host SMBUS process commnunication with Interrupt + * @note : This abort can be called only if state is ready + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @param DevAddress: Target device address + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_Master_Abort_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress) +{ + if(hsmbus->State == HAL_SMBUS_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hsmbus); + + /* Keep the same state as previous */ + /* to perform as well the call of the corresponding end of transfer callback */ + if(hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_TX) + { + hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_TX; + } + else if(hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_RX) + { + hsmbus->State = HAL_SMBUS_STATE_MASTER_BUSY_RX; + } + else + { + /* Wrong usage of abort function */ + /* This function should be used only in case of abort monitored by master device */ + return HAL_ERROR; + } + hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE; + + /* Set NBYTES to 1 to generate a dummy read on SMBUS peripheral */ + /* Set AUTOEND mode, this will generate a NACK then STOP condition to abort the current transfer */ + SMBUS_TransferConfig(hsmbus, DevAddress, 1, SMBUS_AUTOEND_MODE, SMBUS_NO_STARTSTOP); + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Note : The SMBUS interrupts must be enabled after unlocking current process + to avoid the risk of SMBUS interrupt handle execution before current + process unlock */ + if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX) + { + SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_TX); + } + else if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX) + { + SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_RX); + } + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Transmit in slave/device SMBUS mode an amount of data in no-blocking mode with Interrupt + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be sent + * @param XferOptions: Options of Transfer, value of @ref SMBUS_XferOptions_definition + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_Slave_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint8_t *pData, uint16_t Size, uint32_t XferOptions) +{ + /* Check the parameters */ + assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if(hsmbus->State == HAL_SMBUS_STATE_LISTEN) + { + if((pData == NULL) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Disable Interrupts, to prevent preemption during treatment in case of multicall */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR | SMBUS_IT_TX); + + /* Process Locked */ + __HAL_LOCK(hsmbus); + + hsmbus->State |= HAL_SMBUS_STATE_SLAVE_BUSY_TX; + hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE; + + /* Enable Address Acknowledge */ + hsmbus->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Prepare transfer parameters */ + hsmbus->pBuffPtr = pData; + hsmbus->XferSize = Size; + hsmbus->XferCount = Size; + hsmbus->XferOptions = XferOptions; + + if(Size > MAX_NBYTE_SIZE) + { + hsmbus->XferSize = MAX_NBYTE_SIZE; + } + else + { + hsmbus->XferSize = Size; + } + + /* Set NBYTES to write and reload if size > MAX_NBYTE_SIZE and generate RESTART */ + if( (hsmbus->XferSize == MAX_NBYTE_SIZE) && (hsmbus->XferSize < hsmbus->XferCount) ) + { + SMBUS_TransferConfig(hsmbus,0,hsmbus->XferSize, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_NO_STARTSTOP); + } + else + { + /* Set NBYTE to transmit */ + SMBUS_TransferConfig(hsmbus,0,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP); + + /* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */ + /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */ + if(__HAL_SMBUS_GET_PEC_MODE(hsmbus) != RESET) + { + hsmbus->XferSize--; + hsmbus->XferCount--; + } + } + + /* Clear ADDR flag after prepare the transfer parameters */ + /* This action will generate an acknowledge to the HOST */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus,SMBUS_FLAG_ADDR); + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Note : The SMBUS interrupts must be enabled after unlocking current process + to avoid the risk of SMBUS interrupt handle execution before current + process unlock */ + /* REnable ADDR interrupt */ + SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_TX | SMBUS_IT_ADDR); + + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Receive in slave/device SMBUS mode an amount of data in no-blocking mode with Interrupt + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @param pData: Pointer to data buffer + * @param Size: Amount of data to be sent + * @param XferOptions: Options of Transfer, value of @ref SMBUS_XferOptions_definition + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_Slave_Receive_IT(SMBUS_HandleTypeDef *hsmbus, uint8_t *pData, uint16_t Size, uint32_t XferOptions) +{ + /* Check the parameters */ + assert_param(IS_SMBUS_TRANSFER_OPTIONS_REQUEST(XferOptions)); + + if(hsmbus->State == HAL_SMBUS_STATE_LISTEN) + { + if((pData == NULL) || (Size == 0)) + { + return HAL_ERROR; + } + + /* Disable Interrupts, to prevent preemption during treatment in case of multicall */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR | SMBUS_IT_RX); + + /* Process Locked */ + __HAL_LOCK(hsmbus); + + hsmbus->State |= HAL_SMBUS_STATE_SLAVE_BUSY_RX; + hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE; + + /* Enable Address Acknowledge */ + hsmbus->Instance->CR2 &= ~I2C_CR2_NACK; + + /* Prepare transfer parameters */ + hsmbus->pBuffPtr = pData; + hsmbus->XferSize = Size; + hsmbus->XferCount = Size; + hsmbus->XferOptions = XferOptions; + + /* Set NBYTE to receive */ + /* If XferSize equal "1", or XferSize equal "2" with PEC requested (mean 1 data byte + 1 PEC byte */ + /* no need to set RELOAD bit mode, a ACK will be automatically generated in that case */ + /* else need to set RELOAD bit mode to generate an automatic ACK at each byte Received */ + /* This RELOAD bit will be reset for last BYTE to be receive in SMBUS_Slave_ISR */ + if((hsmbus->XferSize == 1) || ((hsmbus->XferSize == 2) && (__HAL_SMBUS_GET_PEC_MODE(hsmbus) != RESET))) + { + SMBUS_TransferConfig(hsmbus,0,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP); + } + else + { + SMBUS_TransferConfig(hsmbus,0, 1, hsmbus->XferOptions | SMBUS_RELOAD_MODE, SMBUS_NO_STARTSTOP); + } + + /* Clear ADDR flag after prepare the transfer parameters */ + /* This action will generate an acknowledge to the HOST */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus,SMBUS_FLAG_ADDR); + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Note : The SMBUS interrupts must be enabled after unlocking current process + to avoid the risk of SMBUS interrupt handle execution before current + process unlock */ + /* REnable ADDR interrupt */ + SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_RX | SMBUS_IT_ADDR); + + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief This function enable the Address listen mode + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_Slave_Listen_IT(SMBUS_HandleTypeDef *hsmbus) +{ + hsmbus->State = HAL_SMBUS_STATE_LISTEN; + + /* Enable the Address Match interrupt */ + SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_ADDR); + + return HAL_OK; +} + +/** + * @brief This function disable the Address listen mode + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_DisableListen_IT(SMBUS_HandleTypeDef *hsmbus) +{ + /* Disable Address listen mode only if a transfer is not ongoing */ + if(hsmbus->State == HAL_SMBUS_STATE_LISTEN) + { + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Disable the Address Match interrupt */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief This function enable the SMBUS alert mode. + * @param hsmbus : pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUSx peripheral. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_EnableAlert_IT(SMBUS_HandleTypeDef *hsmbus) +{ + /* Enable SMBus alert */ + hsmbus->Instance->CR1 |= I2C_CR1_ALERTEN; + + /* Clear ALERT flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ALERT); + + /* Enable Alert Interrupt */ + SMBUS_Enable_IRQ(hsmbus, SMBUS_IT_ALERT); + + return HAL_OK; +} +/** + * @brief This function disable the SMBUS alert mode. + * @param hsmbus : pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUSx peripheral. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_DisableAlert_IT(SMBUS_HandleTypeDef *hsmbus) +{ + /* Enable SMBus alert */ + hsmbus->Instance->CR1 &= ~I2C_CR1_ALERTEN; + + /* Disable Alert Interrupt */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ALERT); + + return HAL_OK; +} +/** + * @brief Checks if target device is ready for communication. + * @note This function is used with Memory devices + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @param DevAddress: Target device address + * @param Trials: Number of trials + * @param Timeout: Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_SMBUS_IsDeviceReady(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint32_t Trials, uint32_t Timeout) +{ + uint32_t tickstart = 0; + + __IO uint32_t SMBUS_Trials = 0; + + if(hsmbus->State == HAL_SMBUS_STATE_READY) + { + if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_BUSY) != RESET) + { + return HAL_BUSY; + } + + /* Process Locked */ + __HAL_LOCK(hsmbus); + + hsmbus->State = HAL_SMBUS_STATE_BUSY; + hsmbus->ErrorCode = HAL_SMBUS_ERROR_NONE; + + do + { + /* Generate Start */ + hsmbus->Instance->CR2 = __HAL_SMBUS_GENERATE_START(hsmbus->Init.AddressingMode,DevAddress); + + /* No need to Check TC flag, with AUTOEND mode the stop is automatically generated */ + /* Wait until STOPF flag is set or a NACK flag is set*/ + tickstart = HAL_GetTick(); + while((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_STOPF) == RESET) && (__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF) == RESET) && (hsmbus->State != HAL_SMBUS_STATE_TIMEOUT)) + { + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0) || ((HAL_GetTick()-tickstart) > Timeout)) + { + /* Device is ready */ + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + return HAL_TIMEOUT; + } + } + } + + /* Check if the NACKF flag has not been set */ + if (__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF) == RESET) + { + /* Wait until STOPF flag is reset */ + if(SMBUS_WaitOnFlagUntilTimeout(hsmbus, SMBUS_FLAG_STOPF, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* Clear STOP Flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF); + + /* Device is ready */ + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + return HAL_OK; + } + else + { + /* Wait until STOPF flag is reset */ + if(SMBUS_WaitOnFlagUntilTimeout(hsmbus, SMBUS_FLAG_STOPF, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* Clear NACK Flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF); + + /* Clear STOP Flag, auto generated with autoend*/ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF); + } + + /* Check if the maximum allowed number of trials has been reached */ + if (SMBUS_Trials++ == Trials) + { + /* Generate Stop */ + hsmbus->Instance->CR2 |= I2C_CR2_STOP; + + /* Wait until STOPF flag is reset */ + if(SMBUS_WaitOnFlagUntilTimeout(hsmbus, SMBUS_FLAG_STOPF, RESET, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* Clear STOP Flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF); + } + }while(SMBUS_Trials < Trials); + + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + return HAL_TIMEOUT; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief This function handles SMBUS event interrupt request. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval None + */ +void HAL_SMBUS_EV_IRQHandler(SMBUS_HandleTypeDef *hsmbus) +{ + uint32_t tmpisrvalue = 0; + + /* Use a local variable to store the current ISR flags */ + /* This action will avoid a wrong treatment due to ISR flags change during interrupt handler */ + tmpisrvalue = __SMBUS_GET_ISR_REG(hsmbus); + + /* SMBUS in mode Transmitter ---------------------------------------------------*/ + if (((__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TXIS) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TCR) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TC) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_STOPF) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_AF) != RESET)) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, (SMBUS_IT_TCI| SMBUS_IT_STOPI| SMBUS_IT_NACKI | SMBUS_IT_TXI)) != RESET)) + { + /* Slave mode selected */ + if ((hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_TX) == HAL_SMBUS_STATE_SLAVE_BUSY_TX) + { + SMBUS_Slave_ISR(hsmbus); + } + /* Master mode selected */ + else if((hsmbus->State & HAL_SMBUS_STATE_MASTER_BUSY_TX) == HAL_SMBUS_STATE_MASTER_BUSY_TX) + { + SMBUS_Master_ISR(hsmbus); + } + } + + /* SMBUS in mode Receiver ----------------------------------------------------*/ + if (((__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_RXNE) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TCR) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TC) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_STOPF) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_AF) != RESET)) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, (SMBUS_IT_TCI| SMBUS_IT_STOPI| SMBUS_IT_NACKI | SMBUS_IT_RXI)) != RESET)) + { + /* Slave mode selected */ + if ((hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_RX) == HAL_SMBUS_STATE_SLAVE_BUSY_RX) + { + SMBUS_Slave_ISR(hsmbus); + } + /* Master mode selected */ + else if((hsmbus->State & HAL_SMBUS_STATE_MASTER_BUSY_RX) == HAL_SMBUS_STATE_MASTER_BUSY_RX) + { + SMBUS_Master_ISR(hsmbus); + } + } + + /* SMBUS in mode Listener Only --------------------------------------------------*/ + if (((__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_ADDR) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_STOPF) != RESET) || (__SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_AF) != RESET)) + && ((__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ADDRI) != RESET) || (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_STOPI) != RESET) || (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_NACKI) != RESET))) + { + if (hsmbus->State == HAL_SMBUS_STATE_LISTEN) + { + SMBUS_Slave_ISR(hsmbus); + } + } +} + +/** + * @brief This function handles SMBUS error interrupt request. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval None + */ +void HAL_SMBUS_ER_IRQHandler(SMBUS_HandleTypeDef *hsmbus) +{ + /* SMBUS Bus error interrupt occurred ------------------------------------*/ + if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_BERR) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET)) + { + hsmbus->ErrorCode |= HAL_SMBUS_ERROR_BERR; + + /* Clear BERR flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_BERR); + } + + /* SMBUS Over-Run/Under-Run interrupt occurred ----------------------------------------*/ + if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_OVR) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET)) + { + hsmbus->ErrorCode |= HAL_SMBUS_ERROR_OVR; + + /* Clear OVR flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_OVR); + } + + /* SMBUS Arbitration Loss error interrupt occurred ------------------------------------*/ + if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_ARLO) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET)) + { + hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ARLO; + + /* Clear ARLO flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ARLO); + } + + /* SMBUS Timeout error interrupt occurred ---------------------------------------------*/ + if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TIMEOUT) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET)) + { + hsmbus->ErrorCode |= HAL_SMBUS_ERROR_BUSTIMEOUT; + + /* Clear TIMEOUT flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_TIMEOUT); + } + + /* SMBUS Alert error interrupt occurred -----------------------------------------------*/ + if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_ALERT) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET)) + { + hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ALERT; + + /* Clear ALERT flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_ALERT); + } + + /* SMBUS Packet Error Check error interrupt occurred ----------------------------------*/ + if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_PECERR) != RESET) && (__HAL_SMBUS_GET_IT_SOURCE(hsmbus, SMBUS_IT_ERRI) != RESET)) + { + hsmbus->ErrorCode |= HAL_SMBUS_ERROR_PECERR; + + /* Clear PEC error flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_PECERR); + } + + /* Call the Error Callback in case of Error detected */ + if((hsmbus->ErrorCode != HAL_SMBUS_ERROR_NONE)&&(hsmbus->ErrorCode != HAL_SMBUS_ERROR_ACKF)) + { + /* Do not Reset the the HAL state in case of ALERT error */ + if((hsmbus->ErrorCode & HAL_SMBUS_ERROR_ALERT) != HAL_SMBUS_ERROR_ALERT) + { + /* Reset only HAL_SMBUS_STATE_SLAVE_BUSY_XX and HAL_SMBUS_STATE_MASTER_BUSY_XX */ + /* keep HAL_SMBUS_STATE_LISTEN if set */ + hsmbus->State &= ~((uint32_t)(HAL_SMBUS_STATE_MASTER_BUSY_RX | HAL_SMBUS_STATE_MASTER_BUSY_TX | HAL_SMBUS_STATE_SLAVE_BUSY_RX | HAL_SMBUS_STATE_SLAVE_BUSY_TX)); + } + + /* Call the Error callback to prevent upper layer */ + HAL_SMBUS_ErrorCallback(hsmbus); + } +} + +/** + * @brief Master Tx Transfer completed callbacks. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval None + */ + __weak void HAL_SMBUS_MasterTxCpltCallback(SMBUS_HandleTypeDef *hsmbus) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SMBUS_TxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Master Rx Transfer completed callbacks. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval None + */ +__weak void HAL_SMBUS_MasterRxCpltCallback(SMBUS_HandleTypeDef *hsmbus) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SMBUS_TxCpltCallback could be implemented in the user file + */ +} + +/** @brief Slave Tx Transfer completed callbacks. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval None + */ + __weak void HAL_SMBUS_SlaveTxCpltCallback(SMBUS_HandleTypeDef *hsmbus) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SMBUS_TxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Slave Rx Transfer completed callbacks. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval None + */ +__weak void HAL_SMBUS_SlaveRxCpltCallback(SMBUS_HandleTypeDef *hsmbus) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SMBUS_TxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Slave Address Match callbacks. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @param TransferDirection: Master request Transfer Direction (Write/Read) + * @param AddrMatchCode: Address Match Code + * @retval None + */ +__weak void HAL_SMBUS_SlaveAddrCallback(SMBUS_HandleTypeDef *hsmbus, uint8_t TransferDirection, uint16_t AddrMatchCode) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SMBUS_SlaveAddrCallback could be implemented in the user file + */ +} + +/** + * @brief Listen Complete callbacks. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval None + */ +__weak void HAL_SMBUS_SlaveListenCpltCallback(SMBUS_HandleTypeDef *hsmbus) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SMBUS_SlaveListenCpltCallback could be implemented in the user file + */ +} + +/** + * @brief SMBUS error callbacks. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval None + */ + __weak void HAL_SMBUS_ErrorCallback(SMBUS_HandleTypeDef *hsmbus) +{ + /* NOTE : This function Should not be modified, when the callback is needed, + the HAL_SMBUS_ErrorCallback could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup HAL_SMBUS_Group3 Peripheral State and Errors functions + * @brief Peripheral State and Errors functions + * +@verbatim + =============================================================================== + ##### Peripheral State and Errors functions ##### + =============================================================================== + [..] + This subsection permit to get in run-time the status of the peripheral + and the data flow. + +@endverbatim + * @{ + */ + +/** + * @brief Returns the SMBUS state. + * @param hsmbus : SMBUS handle + * @retval HAL state + */ +HAL_SMBUS_StateTypeDef HAL_SMBUS_GetState(SMBUS_HandleTypeDef *hsmbus) +{ + return hsmbus->State; +} + +/** +* @brief Return the SMBUS error code +* @param hsmbus : pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. +* @retval SMBUS Error Code +*/ +uint32_t HAL_SMBUS_GetError(SMBUS_HandleTypeDef *hsmbus) +{ + return hsmbus->ErrorCode; +} + +/** + * @} + */ + +/** + * @brief Interrupt Sub-Routine which handle the Interrupt Flags Master Mode + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval HAL status + */ +static HAL_StatusTypeDef SMBUS_Master_ISR(SMBUS_HandleTypeDef *hsmbus) +{ + uint16_t DevAddress; + + /* Process Locked */ + __HAL_LOCK(hsmbus); + + if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF) != RESET) + { + /* Clear NACK Flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF); + + /* Set corresponding Error Code */ + /* No need to generate STOP, it is automatically done */ + hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ACKF; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Call the Error callback to prevent upper layer */ + HAL_SMBUS_ErrorCallback(hsmbus); + } + else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_STOPF) != RESET) + { + + /* Call the corresponding callback to inform upper layer of End of Transfer */ + if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX) + { + /* Disable Interrupt */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX); + + /* Clear STOP Flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF); + + /* Clear Configuration Register 2 */ + __HAL_SMBUS_RESET_CR2(hsmbus); + + /* Flush remaining data in Fifo register in case of error occurs before TXEmpty */ + /* Disable the selected SMBUS peripheral */ + __HAL_SMBUS_DISABLE(hsmbus); + + hsmbus->PreviousState = HAL_SMBUS_STATE_READY; + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* REenable the selected SMBUS peripheral */ + __HAL_SMBUS_ENABLE(hsmbus); + + HAL_SMBUS_MasterTxCpltCallback(hsmbus); + } + else if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX) + { + /* Disable Interrupt */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX); + + /* Clear STOP Flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF); + + /* Clear Configuration Register 2 */ + __HAL_SMBUS_RESET_CR2(hsmbus); + + hsmbus->PreviousState = HAL_SMBUS_STATE_READY; + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + HAL_SMBUS_MasterRxCpltCallback(hsmbus); + } + } + else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_RXNE) != RESET) + { + /* Read data from RXDR */ + (*hsmbus->pBuffPtr++) = hsmbus->Instance->RXDR; + hsmbus->XferSize--; + hsmbus->XferCount--; + } + else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TXIS) != RESET) + { + /* Write data to TXDR */ + hsmbus->Instance->TXDR = (*hsmbus->pBuffPtr++); + hsmbus->XferSize--; + hsmbus->XferCount--; + } + else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TCR) != RESET) + { + if((hsmbus->XferSize == 0)&&(hsmbus->XferCount!=0)) + { + DevAddress = (hsmbus->Instance->CR2 & I2C_CR2_SADD); + + if(hsmbus->XferCount > MAX_NBYTE_SIZE) + { + SMBUS_TransferConfig(hsmbus, DevAddress, MAX_NBYTE_SIZE, (SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE)), SMBUS_NO_STARTSTOP); + hsmbus->XferSize = MAX_NBYTE_SIZE; + } + else + { + hsmbus->XferSize = hsmbus->XferCount; + SMBUS_TransferConfig(hsmbus,DevAddress,hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP); + /* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */ + /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */ + if(__HAL_SMBUS_GET_PEC_MODE(hsmbus) != RESET) + { + hsmbus->XferSize--; + hsmbus->XferCount--; + } + } + } + else if((hsmbus->XferSize == 0)&&(hsmbus->XferCount==0)) + { + /* Call TxCpltCallback if no stop mode is set */ + if(__HAL_SMBUS_GET_STOP_MODE(hsmbus) != SMBUS_AUTOEND_MODE) + { + /* Call the corresponding callback to inform upper layer of End of Transfer */ + if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX) + { + /* Disable Interrupt */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX); + hsmbus->PreviousState = hsmbus->State; + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + HAL_SMBUS_MasterTxCpltCallback(hsmbus); + } + else if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX) + { + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX); + hsmbus->PreviousState = hsmbus->State; + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + HAL_SMBUS_MasterRxCpltCallback(hsmbus); + } + } + } + } + else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TC) != RESET) + { + if(hsmbus->XferCount == 0) + { + /* Specific use case for Quick command */ + if(hsmbus->pBuffPtr == NULL) + { + /* Generate a Stop command */ + hsmbus->Instance->CR2 |= I2C_CR2_STOP; + } + /* Call TxCpltCallback if no stop mode is set */ + else if(__HAL_SMBUS_GET_STOP_MODE(hsmbus) != SMBUS_AUTOEND_MODE) + { + /* No Generate Stop, to permit restart mode */ + /* The stop will be done at the end of transfer, when SMBUS_AUTOEND_MODE enable */ + + /* Call the corresponding callback to inform upper layer of End of Transfer */ + if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_TX) + { + /* Disable Interrupt */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX); + hsmbus->PreviousState = hsmbus->State; + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + HAL_SMBUS_MasterTxCpltCallback(hsmbus); + } + else if(hsmbus->State == HAL_SMBUS_STATE_MASTER_BUSY_RX) + { + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX); + hsmbus->PreviousState = hsmbus->State; + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + HAL_SMBUS_MasterRxCpltCallback(hsmbus); + } + } + } + } + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + return HAL_OK; +} +/** + * @brief Interrupt Sub-Routine which handle the Interrupt Flags Slave Mode + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @retval HAL status + */ +static HAL_StatusTypeDef SMBUS_Slave_ISR(SMBUS_HandleTypeDef *hsmbus) +{ + uint8_t TransferDirection = 0; + uint16_t SlaveAddrCode = 0; + + /* Process Locked */ + __HAL_LOCK(hsmbus); + + if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_AF) != RESET) + { + /* Check that SMBUS transfer finished */ + /* if yes, normal usecase, a NACK is sent by the HOST when Transfer is finished */ + /* Mean XferCount == 0*/ + /* So clear Flag NACKF only */ + if(hsmbus->XferCount == 0) + { + /* Clear NACK Flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF); + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + } + else + { + /* if no, error usecase, a Non-Acknowledge of last Data is generated by the HOST*/ + /* Clear NACK Flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_AF); + + /* Set HAL State to "Idle" State, mean to LISTEN state */ + /* So reset Slave Busy state */ + hsmbus->PreviousState = hsmbus->State; + hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_TX); + hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_RX); + + /* Disable RX/TX Interrupts, keep only ADDR Interrupt */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX | SMBUS_IT_TX); + + /* Set ErrorCode corresponding to a Non-Acknowledge */ + hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ACKF; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Call the Error callback to prevent upper layer */ + HAL_SMBUS_ErrorCallback(hsmbus); + } + } + else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_ADDR) != RESET) + { + TransferDirection = __HAL_SMBUS_GET_DIR(hsmbus); + SlaveAddrCode = __HAL_SMBUS_GET_ADDR_MATCH(hsmbus); + + /* Disable ADDR interrupt to prevent multiple ADDRInterrupt*/ + /* Other ADDRInterrupt will be treat in next Listen usecase */ + __HAL_SMBUS_DISABLE_IT(hsmbus, SMBUS_IT_ADDRI); + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Call Slave Addr callback */ + HAL_SMBUS_SlaveAddrCallback(hsmbus, TransferDirection, SlaveAddrCode); + } + else if((__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_RXNE) != RESET) || (__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TCR) != RESET)) + { + if( (hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_RX) == HAL_SMBUS_STATE_SLAVE_BUSY_RX) + { + /* Read data from RXDR */ + (*hsmbus->pBuffPtr++) = hsmbus->Instance->RXDR; + hsmbus->XferSize--; + hsmbus->XferCount--; + + if(hsmbus->XferCount == 1) + { + /* Receive last Byte, can be PEC byte in case of PEC BYTE enabled */ + /* or only the last Byte of Transfer */ + /* So reset the RELOAD bit mode */ + hsmbus->XferOptions &= ~SMBUS_RELOAD_MODE; + SMBUS_TransferConfig(hsmbus,0 ,1 , hsmbus->XferOptions, SMBUS_NO_STARTSTOP); + } + else if(hsmbus->XferCount == 0) + { + /* Last Byte is received, disable Interrupt */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX); + + /* Remove HAL_SMBUS_STATE_SLAVE_BUSY_RX, keep only HAL_SMBUS_STATE_LISTEN */ + hsmbus->PreviousState = hsmbus->State; + hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_RX); + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Call the Rx complete callback to inform upper layer of the end of receive process */ + HAL_SMBUS_SlaveRxCpltCallback(hsmbus); + } + else + { + /* Set Reload for next Bytes */ + SMBUS_TransferConfig(hsmbus,0, 1, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_NO_STARTSTOP); + + /* Ack last Byte Read */ + hsmbus->Instance->CR2 &= ~I2C_CR2_NACK; + } + } + else if( (hsmbus->State & HAL_SMBUS_STATE_SLAVE_BUSY_TX) == HAL_SMBUS_STATE_SLAVE_BUSY_TX) + { + if((hsmbus->XferSize == 0)&&(hsmbus->XferCount!=0)) + { + if(hsmbus->XferCount > MAX_NBYTE_SIZE) + { + SMBUS_TransferConfig(hsmbus, 0, MAX_NBYTE_SIZE, (SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE)), SMBUS_NO_STARTSTOP); + hsmbus->XferSize = MAX_NBYTE_SIZE; + } + else + { + hsmbus->XferSize = hsmbus->XferCount; + SMBUS_TransferConfig(hsmbus, 0, hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP); + /* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */ + /* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */ + if(__HAL_SMBUS_GET_PEC_MODE(hsmbus) != RESET) + { + hsmbus->XferSize--; + hsmbus->XferCount--; + } + } + } + } + } + else if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_TXIS) != RESET) + { + /* Write data to TXDR only if XferCount not reach "0" */ + /* A TXIS flag can be set, during STOP treatment */ + /* Check if all Datas have already been sent */ + /* If it is the case, this last write in TXDR is not sent, correspond to a dummy TXIS event */ + if(hsmbus->XferCount > 0) + { + /* Write data to TXDR */ + hsmbus->Instance->TXDR = (*hsmbus->pBuffPtr++); + hsmbus->XferCount--; + hsmbus->XferSize--; + } + + if(hsmbus->XferCount == 0) + { + /* Last Byte is Transmitted */ + /* Remove HAL_SMBUS_STATE_SLAVE_BUSY_TX, keep only HAL_SMBUS_STATE_LISTEN */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_TX); + hsmbus->PreviousState = hsmbus->State; + hsmbus->State &= ~((uint32_t)HAL_SMBUS_STATE_SLAVE_BUSY_TX); + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Call the Tx complete callback to inform upper layer of the end of transmit process */ + HAL_SMBUS_SlaveTxCpltCallback(hsmbus); + } + } + + /* Check if STOPF is set */ + if(__HAL_SMBUS_GET_FLAG(hsmbus, SMBUS_FLAG_STOPF) != RESET) + { + if((hsmbus->State & HAL_SMBUS_STATE_LISTEN) == HAL_SMBUS_STATE_LISTEN) + { + /* Disable RX and TX Interrupts */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_RX | SMBUS_IT_TX); + + /* Disable ADDR Interrupt */ + SMBUS_Disable_IRQ(hsmbus, SMBUS_IT_ADDR); + + /* Disable Address Acknowledge */ + hsmbus->Instance->CR2 |= I2C_CR2_NACK; + + /* Clear Configuration Register 2 */ + __HAL_SMBUS_RESET_CR2(hsmbus); + + /* Clear STOP Flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus, SMBUS_FLAG_STOPF); + + /* Clear ADDR flag */ + __HAL_SMBUS_CLEAR_FLAG(hsmbus,SMBUS_FLAG_ADDR); + + hsmbus->XferOptions = 0; + hsmbus->PreviousState = hsmbus->State; + hsmbus->State = HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + /* Call the Listen Complete callback, to prevent upper layer of the end of Listen usecase */ + HAL_SMBUS_SlaveListenCpltCallback(hsmbus); + } + } + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + return HAL_OK; +} +/** + * @brief Manage the enabling of Interrupts + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @param InterruptRequest : Value of @ref SMBUS_Interrupt_configuration_definition. + * @retval HAL status + */ +static HAL_StatusTypeDef SMBUS_Enable_IRQ(SMBUS_HandleTypeDef *hsmbus, uint16_t InterruptRequest) +{ + uint32_t tmpisr = 0; + + if((InterruptRequest & SMBUS_IT_ALERT) == SMBUS_IT_ALERT) + { + /* Enable ERR interrupt */ + tmpisr |= SMBUS_IT_ERRI; + } + + if((InterruptRequest & SMBUS_IT_ADDR) == SMBUS_IT_ADDR) + { + /* Enable ADDR, STOP interrupt */ + tmpisr |= SMBUS_IT_ADDRI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_ERRI; + } + + if((InterruptRequest & SMBUS_IT_TX) == SMBUS_IT_TX) + { + /* Enable ERR, TC, STOP, NACK, RXI interrupt */ + tmpisr |= SMBUS_IT_ERRI | SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_TXI; + } + + if((InterruptRequest & SMBUS_IT_RX) == SMBUS_IT_RX) + { + /* Enable ERR, TC, STOP, NACK, TXI interrupt */ + tmpisr |= SMBUS_IT_ERRI | SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_RXI; + } + + /* Enable interrupts only at the end */ + /* to avoid the risk of SMBUS interrupt handle execution before */ + /* all interrupts requested done */ + __HAL_SMBUS_ENABLE_IT(hsmbus, tmpisr); + + return HAL_OK; +} +/** + * @brief Manage the disabling of Interrupts + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @param InterruptRequest : Value of @ref SMBUS_Interrupt_configuration_definition. + * @retval HAL status + */ +static HAL_StatusTypeDef SMBUS_Disable_IRQ(SMBUS_HandleTypeDef *hsmbus, uint16_t InterruptRequest) +{ + uint32_t tmpisr = 0; + + if( ((InterruptRequest & SMBUS_IT_ALERT) == SMBUS_IT_ALERT) && (hsmbus->State == HAL_SMBUS_STATE_READY) ) + { + /* Disable ERR interrupt */ + tmpisr |= SMBUS_IT_ERRI; + } + + if((InterruptRequest & SMBUS_IT_TX) == SMBUS_IT_TX) + { + /* Disable TC, STOP, NACK, TXI interrupt */ + tmpisr |= SMBUS_IT_TCI | SMBUS_IT_TXI; + + if((__HAL_SMBUS_GET_ALERT_ENABLED(hsmbus) == RESET) + && ((hsmbus->State & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN)) + { + /* Disable ERR interrupt */ + tmpisr |= SMBUS_IT_ERRI; + } + + if((hsmbus->State & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN) + { + /* Disable STOPI, NACKI */ + tmpisr |= SMBUS_IT_STOPI | SMBUS_IT_NACKI; + } + } + + if((InterruptRequest & SMBUS_IT_RX) == SMBUS_IT_RX) + { + /* Disable TC, STOP, NACK, RXI interrupt */ + tmpisr |= SMBUS_IT_TCI | SMBUS_IT_RXI; + + if((__HAL_SMBUS_GET_ALERT_ENABLED(hsmbus) == RESET) + && ((hsmbus->State & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN)) + { + /* Disable ERR interrupt */ + tmpisr |= SMBUS_IT_ERRI; + } + + if((hsmbus->State & HAL_SMBUS_STATE_LISTEN) != HAL_SMBUS_STATE_LISTEN) + { + /* Disable STOPI, NACKI */ + tmpisr |= SMBUS_IT_STOPI | SMBUS_IT_NACKI; + } + } + + if((InterruptRequest & SMBUS_IT_ADDR) == SMBUS_IT_ADDR) + { + /* Enable ADDR, STOP interrupt */ + tmpisr |= SMBUS_IT_ADDRI | SMBUS_IT_STOPI | SMBUS_IT_NACKI; + + if(__HAL_SMBUS_GET_ALERT_ENABLED(hsmbus) == RESET) + { + /* Disable ERR interrupt */ + tmpisr |= SMBUS_IT_ERRI; + } + } + + /* Disable interrupts only at the end */ + /* to avoid a breaking situation like at "t" time */ + /* all disable interrupts request are not done */ + __HAL_SMBUS_DISABLE_IT(hsmbus, tmpisr); + + return HAL_OK; +} +/** + * @brief This function handles SMBUS Communication Timeout. + * @param hsmbus : Pointer to a SMBUS_HandleTypeDef structure that contains + * the configuration information for the specified SMBUS. + * @param Flag: specifies the SMBUS flag to check. + * @param Status: The new Flag status (SET or RESET). + * @param Timeout: Timeout duration + * @retval HAL status + */ +static HAL_StatusTypeDef SMBUS_WaitOnFlagUntilTimeout(SMBUS_HandleTypeDef *hsmbus, uint32_t Flag, FlagStatus Status, uint32_t Timeout) +{ + uint32_t tickstart = HAL_GetTick(); + + /* Wait until flag is set */ + if(Status == RESET) + { + while(__HAL_SMBUS_GET_FLAG(hsmbus, Flag) == RESET) + { + /* Check for the Timeout */ + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0) || ((HAL_GetTick()-tickstart) > Timeout)) + { + hsmbus->PreviousState = hsmbus->State; + hsmbus->State= HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + return HAL_TIMEOUT; + } + } + } + } + else + { + while(__HAL_SMBUS_GET_FLAG(hsmbus, Flag) != RESET) + { + /* Check for the Timeout */ + if(Timeout != HAL_MAX_DELAY) + { + if((Timeout == 0) || ((HAL_GetTick()-tickstart) > Timeout)) + { + hsmbus->PreviousState = hsmbus->State; + hsmbus->State= HAL_SMBUS_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hsmbus); + + return HAL_TIMEOUT; + } + } + } + } + return HAL_OK; +} + +/** + * @brief Handles SMBUSx communication when starting transfer or during transfer (TC or TCR flag are set). + * @param hsmbus: SMBUS handle. + * @param DevAddress: specifies the slave address to be programmed. + * @param Size: specifies the number of bytes to be programmed. + * This parameter must be a value between 0 and 255. + * @param Mode: new state of the SMBUS START condition generation. + * This parameter can be one or a combination of the following values: + * @arg SMBUS_NO_MODE: No specific mode enabled. + * @arg SMBUS_RELOAD_MODE: Enable Reload mode. + * @arg SMBUS_AUTOEND_MODE: Enable Automatic end mode. + * @arg SMBUS_SOFTEND_MODE: Enable Software end mode and Reload mode. + * @param Request: new state of the SMBUS START condition generation. + * This parameter can be one of the following values: + * @arg SMBUS_NO_STARTSTOP: Don't Generate stop and start condition. + * @arg SMBUS_GENERATE_STOP: Generate stop condition (Size should be set to 0). + * @arg SMBUS_GENERATE_START_READ: Generate Restart for read request. + * @arg SMBUS_GENERATE_START_WRITE: Generate Restart for write request. + * @retval None + */ +static void SMBUS_TransferConfig(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t Size, uint32_t Mode, uint32_t Request) +{ + uint32_t tmpreg = 0; + + /* Check the parameters */ + assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance)); + assert_param(IS_SMBUS_TRANSFER_MODE(Mode)); + assert_param(IS_SMBUS_TRANSFER_REQUEST(Request)); + + /* Get the CR2 register value */ + tmpreg = hsmbus->Instance->CR2; + + /* clear tmpreg specific bits */ + tmpreg &= (uint32_t)~((uint32_t)(I2C_CR2_SADD | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_AUTOEND | I2C_CR2_RD_WRN | I2C_CR2_START | I2C_CR2_STOP | I2C_CR2_PECBYTE)); + + /* update tmpreg */ + tmpreg |= (uint32_t)(((uint32_t)DevAddress & I2C_CR2_SADD) | (((uint32_t)Size << 16 ) & I2C_CR2_NBYTES) | \ + (uint32_t)Mode | (uint32_t)Request); + + /* update CR2 register */ + hsmbus->Instance->CR2 = tmpreg; +} + +/** + * @} + */ + +#endif /* HAL_SMBUS_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/