mbed library sources modified for open wear
Dependents: openwear-lifelogger-example
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_STM32F407VG/stm32f4xx_hal_pwr_ex.c
- Revision:
- 297:ec1b66a3d094
- Parent:
- 242:7074e42da0b2
diff -r 34c3abf3e563 -r ec1b66a3d094 targets/cmsis/TARGET_STM/TARGET_STM32F407VG/stm32f4xx_hal_pwr_ex.c --- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_STM32F407VG/stm32f4xx_hal_pwr_ex.c Thu Aug 21 15:00:08 2014 +0100 @@ -0,0 +1,329 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_pwr_ex.c + * @author MCD Application Team + * @version V1.1.0RC2 + * @date 14-May-2014 + * @brief Extended PWR HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of PWR extension peripheral: + * + Peripheral Extended features functions + * + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @defgroup PWREx + * @brief PWR HAL module driver + * @{ + */ + +#ifdef HAL_PWR_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +#define PWR_OVERDRIVE_TIMEOUT_VALUE 1000 +#define PWR_BKPREG_TIMEOUT_VALUE 1000 +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup PWREx_Private_Functions + * @{ + */ + +/** @defgroup PWREx_Group1 Peripheral Extended features functions + * @brief Peripheral Extended features functions + * +@verbatim + + =============================================================================== + ##### Peripheral extended features functions ##### + =============================================================================== + + *** Main and Backup Regulators configuration *** + ================================================ + [..] + (+) The backup domain includes 4 Kbytes of backup SRAM accessible only from + the CPU, and address in 32-bit, 16-bit or 8-bit mode. Its content is + retained even in Standby or VBAT mode when the low power backup regulator + is enabled. It can be considered as an internal EEPROM when VBAT is + always present. You can use the HAL_PWR_EnableBkUpReg() function to + enable the low power backup regulator. + + (+) When the backup domain is supplied by VDD (analog switch connected to VDD) + the backup SRAM is powered from VDD which replaces the VBAT power supply to + save battery life. + + (+) The backup SRAM is not mass erased by a tamper event. It is read + protected to prevent confidential data, such as cryptographic private + key, from being accessed. The backup SRAM can be erased only through + the Flash interface when a protection level change from level 1 to + level 0 is requested. + -@- Refer to the description of Read protection (RDP) in the Flash + programming manual. + + (+) The main internal regulator can be configured to have a tradeoff between + performance and power consumption when the device does not operate at + the maximum frequency. This is done through __HAL_PWR_MAINREGULATORMODE_CONFIG() + macro which configure VOS bit in PWR_CR register + + Refer to the product datasheets for more details. + + *** FLASH Power Down configuration **** + ======================================= + [..] + (+) By setting the FPDS bit in the PWR_CR register by using the + HAL_PWR_EnableFlashPowerDown() function, the Flash memory also enters power + down mode when the device enters Stop mode. When the Flash memory + is in power down mode, an additional startup delay is incurred when + waking up from Stop mode. + + (+) For STM32F42xxx/43xxx Devices, the scale can be modified only when the PLL + is OFF and the HSI or HSE clock source is selected as system clock. + The new value programmed is active only when the PLL is ON. + When the PLL is OFF, the voltage scale 3 is automatically selected. + Refer to the datasheets for more details. + + *** Over-Drive and Under-Drive configuration **** + ================================================= + [..] + (+) For STM32F42xxx/43xxx Devices, in Run mode: the main regulator has + 2 operating modes available: + (++) Normal mode: The CPU and core logic operate at maximum frequency at a given + voltage scaling (scale 1, scale 2 or scale 3) + (++) Over-drive mode: This mode allows the CPU and the core logic to operate at a + higher frequency than the normal mode for a given voltage scaling (scale 1, + scale 2 or scale 3). This mode is enabled through HAL_PWREx_EnableOverDrive() function and + disabled by HAL_PWREx_DisableOverDrive() function, to enter or exit from Over-drive mode please follow + the sequence described in Reference manual. + + (+) For STM32F42xxx/43xxx Devices, in Stop mode: the main regulator or low power regulator + supplies a low power voltage to the 1.2V domain, thus preserving the content of registers + and internal SRAM. 2 operating modes are available: + (++) Normal mode: the 1.2V domain is preserved in nominal leakage mode. This mode is only + available when the main regulator or the low power regulator is used in Scale 3 or + low voltage mode. + (++) Under-drive mode: the 1.2V domain is preserved in reduced leakage mode. This mode is only + available when the main regulator or the low power regulator is in low voltage mode. + +@endverbatim + * @{ + */ + +/** + * @brief Enables the Backup Regulator. + * @param None + * @retval HAL status + */ +HAL_StatusTypeDef HAL_PWREx_EnableBkUpReg(void) +{ + uint32_t timeout = 0; + + *(__IO uint32_t *) CSR_BRE_BB = (uint32_t)ENABLE; + + /* Get timeout */ + timeout = HAL_GetTick() + PWR_BKPREG_TIMEOUT_VALUE; + /* Wait till Backup regulator ready flag is set */ + while(__HAL_PWR_GET_FLAG(PWR_FLAG_BRR) == RESET) + { + if(HAL_GetTick() >= timeout) + { + return HAL_TIMEOUT; + } + } + return HAL_OK; +} + +/** + * @brief Disables the Backup Regulator. + * @param None + * @retval HAL status + */ +HAL_StatusTypeDef HAL_PWREx_DisableBkUpReg(void) +{ + uint32_t timeout = 0; + + *(__IO uint32_t *) CSR_BRE_BB = (uint32_t)DISABLE; + + /* Get timeout */ + timeout = HAL_GetTick() + PWR_BKPREG_TIMEOUT_VALUE; + /* Wait till Backup regulator ready flag is set */ + while(__HAL_PWR_GET_FLAG(PWR_FLAG_BRR) != RESET) + { + if(HAL_GetTick() >= timeout) + { + return HAL_TIMEOUT; + } + } + return HAL_OK; +} + +/** + * @brief Enables the Flash Power Down in Stop mode. + * @param None + * @retval None + */ +void HAL_PWREx_EnableFlashPowerDown(void) +{ + *(__IO uint32_t *) CR_FPDS_BB = (uint32_t)ENABLE; +} + +/** + * @brief Disables the Flash Power Down in Stop mode. + * @param None + * @retval None + */ +void HAL_PWREx_DisableFlashPowerDown(void) +{ + *(__IO uint32_t *) CR_FPDS_BB = (uint32_t)DISABLE; +} + +#if defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx) +/** + * @brief Activates the Over-Drive mode. + * @note These macros can be used only for STM32F42xx/STM32F43xx devices. + * This mode allows the CPU and the core logic to operate at a higher frequency + * than the normal mode for a given voltage scaling (scale 1, scale 2 or scale 3). + * @note It is recommended to enter or exit Over-drive mode when the application is not running + * critical tasks and when the system clock source is either HSI or HSE. + * During the Over-drive switch activation, no peripheral clocks should be enabled. + * The peripheral clocks must be enabled once the Over-drive mode is activated. + * @param None + * @retval HAL status + */ +HAL_StatusTypeDef HAL_PWREx_ActivateOverDrive(void) +{ + uint32_t timeout = 0; + + __PWR_CLK_ENABLE(); + + /* Enable the Over-drive to extend the clock frequency to 180 Mhz */ + __HAL_PWR_OVERDRIVE_ENABLE(); + + /* Get timeout */ + timeout = HAL_GetTick() + PWR_OVERDRIVE_TIMEOUT_VALUE; + while(!__HAL_PWR_GET_FLAG(PWR_FLAG_ODRDY)) + { + if(HAL_GetTick() >= timeout) + { + return HAL_TIMEOUT; + } + } + + /* Enable the Over-drive switch */ + __HAL_PWR_OVERDRIVESWITCHING_ENABLE(); + + /* Get timeout */ + timeout = HAL_GetTick() + PWR_OVERDRIVE_TIMEOUT_VALUE; + while(!__HAL_PWR_GET_FLAG(PWR_FLAG_ODSWRDY)) + { + if(HAL_GetTick() >= timeout) + { + return HAL_TIMEOUT; + } + } + return HAL_OK; +} + +/** + * @brief Deactivates the Over-Drive mode. + * @note These macros can be used only for STM32F42xx/STM32F43xx devices. + * This mode allows the CPU and the core logic to operate at a higher frequency + * than the normal mode for a given voltage scaling (scale 1, scale 2 or scale 3). + * @note It is recommended to enter or exit Over-drive mode when the application is not running + * critical tasks and when the system clock source is either HSI or HSE. + * During the Over-drive switch activation, no peripheral clocks should be enabled. + * The peripheral clocks must be enabled once the Over-drive mode is activated. + * @param None + * @retval HAL status + */ +HAL_StatusTypeDef HAL_PWREx_DeactivateOverDrive(void) +{ + uint32_t timeout = 0; + + __PWR_CLK_ENABLE(); + + /* Disable the Over-drive switch */ + __HAL_PWR_OVERDRIVESWITCHING_DISABLE(); + + /* Get timeout */ + timeout = HAL_GetTick() + PWR_OVERDRIVE_TIMEOUT_VALUE; + + while(__HAL_PWR_GET_FLAG(PWR_FLAG_ODSWRDY)) + { + if(HAL_GetTick() >= timeout) + { + return HAL_TIMEOUT; + } + } + + /* Disable the Over-drive */ + __HAL_PWR_OVERDRIVE_DISABLE(); + + /* Get timeout */ + timeout = HAL_GetTick() + PWR_OVERDRIVE_TIMEOUT_VALUE; + + while(__HAL_PWR_GET_FLAG(PWR_FLAG_ODRDY)) + { + if(HAL_GetTick() >= timeout) + { + return HAL_TIMEOUT; + } + } + + return HAL_OK; +} +#endif /* STM32F427xx || STM32F437xx || STM32F429xx || STM32F439xx */ +/** + * @} + */ + +/** + * @} + */ + +#endif /* HAL_PWR_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/